Cisco Systems D200 manual

CH A P T E R 19-1 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 19 DLPs D200 to D299 DLP-D201 Apply a Lock-On Note T o apply a lock -on to a protect card in a 1:1 or 1:N protection grou p, the protect card must b e acti ve. If the prote ct card is in standby , th e Lock On button is disa bled. T o make the protect card acti ve, you must sw[...]

19-2 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D202 Apply a Lockout The Lock On stat e has been applied and t raf f ic cann ot be switch ed to the w orking car d. T o clear t he Lock On state, see the “DLP-D203 Clear a Lock-O n or Lockout” task on page 19-3 . Step 8 Return to your ori ginating proc[...]

19-3 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D203 Clear a Lock-On or Lo ckout DLP-D203 Clear a Lock-On or Lockout Step 1 In node vie w , click the Maintenance > Protection tabs. Step 2 In the Protection Groups list , click the protectio n group that contains the card you w ant to clear . Step 3 In[...]

19-4 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D205 Clean Fiber Conne ctors with CLETOP Step 3 Blo w-dry using filtered air . Step 4 Use an inspection microscope to inspect each fiber connector for dirt, cracks, or scratches. If the connector is not clean, repeat Steps 1 to 3 . Step 5 Insert the f ib e[...]

19-5 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D206 Clean the Fiber Adapters DLP-D206 Clean the Fiber Adapters Step 1 Remov e the dust plu g from the f iber adapter . Step 2 Insert a CLET OP stick swab (1410 0400) into the adapter op ening and rotate the swab . Step 3 Place dust plugs on th e fib er ad[...]

19-6 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D208 Change External Al arms Using the AIC-I Card DLP-D208 Change External Alarms Using the AIC-I Card Step 1 Confir m that e xternal-de vice relay s are wired to the ENVIR ALARMS IN p ins on the MIC-A/P Front Mount Electrical Connection (FMEC). See the ?[...]

19-7 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D210 Change AIC-I Card Orderwire Settings Step 3 On the External Controls subtab, modify any of t he follo wing f ields for each external contro l wired to the ONS 1545 4 SDH MIC-A/P card. For definitions of these fields, see the “NTP-D247 Pro vision Ext[...]

19-8 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D211 Provision CE- 1000-4 Ethernet Ports DLP-D211 Provision CE-1000-4 Ethernet Ports Note Y ou can provision SONET contiguous concatenated (CCA T) or virtual concatenat ed ( VCA T) circuits for the CE-1000-4 before or after pro visioning the card’ s Ethe[...]

19-9 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D212 Create a User Data Channel Circuit Note Reprovision ing an Ethernet port on the CE-1000- 4 card does not reset the Ethernet statistics for that port. Step 6 Return to your ori ginating procedure (NTP). DLP-D212 Create a User Data Channel Circuit Step [...]

19-10 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D213 Provision th e Card Mode for ML-Series Ethernet Cards DLP-D213 Provision the Card Mode for ML-Series Ethernet Cards Step 1 In node vie w , double-click the ML-Series Ethernet card graphic to open the card. Step 2 Click the Pro visioning > Card tab[...]

19-11 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D215 Consolidate Links in Network View Step 2 Click the Pro visioning > Line tabs for all cards except the G-Series card. For the G-Series card, click the Provisio ning > Port tabs. Step 3 In the Admin State column for the tar get port, choose on e [...]

19-12 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D215 Consolidate Links in Ne twork View Step 1 From the V iew men u, choose Go to Network V i ew . CTC shows the link icons by default. Step 2 As needed, perfo rm one or more o f the follo wing steps: • T o toggle link icons on and of f, go to Step 3 . [...]

19-13 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D215 Consolidate Links in Network View Figur e 19-2 Consolidated Links in Networ k View Figure 19-3 sh o ws a dif feren t network vie w with local DCC link consolidation between t wo nodes. Figur e 19-3 Networ k View with Local Link Consolidation Step 6 T[...]

19-14 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D216 Change the STM-N Card ALS Maintenance Settings b. Check the check box es ne xt to the links t hat you want to display . c. Click OK . Step 10 Return to your ori ginating procedure (NTP). DLP-D216 Change the STM-N Card ALS Maintenance Settings Note Fo[...]

19-15 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D216 Change the STM-N Card ALS Maintenance Settings Step 4 Click Apply . If the change affects traf f ic, a warning message displays. Click Ye s to complete the change. Step 5 Return to your ori ginating procedure (NTP). T able 1 9-2 STM-N Maint enance Se[...]

19-16 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D217 MS-SPRing Exercise Ring Test DLP-D217 MS-SPRing Exercise Ring Test Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 Click the Pro visioning > MS-SPRing tabs. Step 3 Click the ro w of the MS-SPRing you will e x ercise, then click E[...]

19-17 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D217 MS-SPRing Exercise Ring T est Step 5 Exercise the east port: a. Right-click the east port o f any MS-SPRing node and choose Set East Pr otection Opera tion . Note For tw o fiber MS- SPRings, the squares on the node icons represen t the MS-SPRing work[...]

19-18 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D218 Provision SNCP Ring Se lectors During Circuit Creation DLP-D218 Provision SNCP Ring Selectors During Circuit Creation Note Provisioning SD-P or SF-P thresholds on the Circuit Attrib utes page of the Circuit Creation wizard sets the values only for SN[...]

19-19 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D219 Provision a Low-Order Tunnel Route DLP-D219 Provision a Low-Order Tunnel Route Step 1 In the Circuit Creation wizard i n th e Route Revie w and Edit area, click the source node icon if it is not already selected. Arrows indicate the a vailable sp ans[...]

19-20 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D221 Provision E-Series Ethe rnet Ports for VLA N Membership Note Both 1000 Full and Au to modes set the E1000-2- G port to the 1000 Mbps and Full duple x operating mode; ho wever , flow con trol is disabled when 1000 Full is selected. Choosi ng Auto mode[...]

19-21 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D221 Provision E-Series Ether net Ports for VLAN Membership • If a port is a member of only one VLAN, cho ose Untag from the Port column in the VLAN’ s row . Choose -- for all the other VLAN ro ws in that Port col umn. Note The VLAN with Untag selecte[...]

19-22 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D222 Provision G-Series Ethern et Ports DLP-D222 Provision G-Series Ethernet Ports Step 1 In node vie w , double-click the G-Series card graphic to open the card. Step 2 Click the Pro visioning > Por t tabs. Step 3 For each G-Seri es port, pro vision t[...]

19-23 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D223 Download an Alarm Severity Profile Note Reprovision ing an Ethernet po rt on the G-Series card does n ot reset the Ethernet statistics for that port. Step 6 Return to your ori ginating procedure (NTP). DLP-D223 Download an Alarm Severity Profile Step[...]

19-24 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D224 Adjust the Java Virtual Memory Heap Size Note The Default alarm profile list contains alarm and condition se v erities that correspond when applicable to default valu es esta blished in T elcordia GR-253-CORE. Note All default or user -def ined se v [...]

19-25 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D225 Enable Alarm Filtering Step 7 Ty p e 512 in the V ariable V alue field. Step 8 Click OK . Step 9 Reboot your PC. Step 10 Return to your ori ginating procedure (NTP). DLP-D225 Enable Alarm Filtering Step 1 At node, network, or car d vie w , click the [...]

19-26 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D227 Disable Alarm Filtering DLP-D227 Disable Alarm Filtering Step 1 At node, network, or car d vie w , click the Alarms tab . Step 2 Click the Filter tool at the lo wer -ri ght side of the bottom to olbar . Alarm filt ering is enabled if the t ool is ind[...]

19-27 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D230 Change a Circuit State In the Circuits on Span dialog bo x, you can vie w the follo wing in formation about the cir cuits that tra verse th e span. The information t hat appears depends on the circuit type. F or lo w-order and high-or der circuits pr[...]

19-28 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D231 Edit a Circuit Name Step 5 In the Set Circuit State di alog box, choose the administrati v e state fr om the T arget Circuit Admin State drop-do wn list: • Unlocked—Puts the circuit cr oss-connects in the Unlock ed-enabled service state. • Lock[...]

19-29 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D232 Change Active and Standby Spa n Color Step 2 Click the circuit you wa nt to rename, then cli ck Edit . Step 3 If you want to edit a VCA T circuit member name, complete the fol lo wing steps in the Edit Circuit window to access the Edit Member wind o [...]

19-30 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D233 Edit SNCP Circuit Path Selectors c. Click OK to close the Pick a Color dialog box. If you wa nt to change th e standb y span color , continue with Step 5 . If not, click OK to s av e th e change an d close the Pref erences dialog box , or click Apply[...]

19-31 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D234 Roll the Source or De stination of One Optical Circuit • (VC4 circuits onl y) In the VC LO Circuit s Only area, set the follo wing t hresholds: – SF threshold—Sets the SNCP si gnal failure BER threshold. – SD threshold— Sets the SNCP si gna[...]

19-32 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D234 Roll the Source or Destination of One Op tical Circuit Figur e 1 9-5 Selecting Single Roll At tr ibut es Step 6 Click Next . Step 7 In the Pi vot/ Fixed Poi nt 1 windo w , click the square in the graphic image that repr esents the facility that you w[...]

19-33 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D234 Roll the Source or De stination of One Optical Circuit Figur e 1 9-7 Selecting a New Endpoint Step 10 Click Finish . On the Circuits tab, t he circuit status for the Roll Fro m port changes from DISCO VERED to R O LL_PENDING. Step 11 Click the Rolls [...]

19-34 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D235 Roll One Cross-Connec t from an Optical Circuit to a Second Optical Circuit Figur e 19-8 Viewing the Rolls T ab Step 12 If you selected Manual in Step 5 , click the rolled f acility on the Roll s tab and then click Complete . If you selected Auto, co[...]

19-35 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D235 Roll One Cross-Connect from an Op tical Circuit to a Second Optical Circuit b. From the Circuit Roll T y pe drop-do wn list, choose Single to indicate that yo u want t o roll a single connection from the Roll Fro m circuit to the Roll T o circuit. c.[...]

19-36 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Conn ects on One Optic al Circuit Using Automatic Ro uting • A roll can be forced onto th e Roll T o Circuit destination without a v a lid signal by using t he Force V alid Signal button. If you choose Force V alid Signal, traff ic o[...]

19-37 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Figur e 1 9-1 0 Selecting Dual Roll At tr ibutes Step 6 Click Next . Step 7 In the Pi v ot/Fix ed Point 1 w indo w , click the square re presenting the f ix ed path of the first c[...]

19-38 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Conn ects on One Optic al Circuit Using Automatic Ro uting Figure 1 9-1 1 Setting Roll Routing Pr efer enc es Step 13 T o route the circuit ov er a protected path, check Fully Protected Path . (If you do not w ant to route th e circuit[...]

19-39 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D236 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Step 16 If you check ed Re vie w Route Before Creation in Step 12 : a. In the Roll Route Re vie w an d Edit area, re vie w the circuit rout e. T o add or delete a circuit span, se[...]

19-40 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D237 Roll Two Cross-Conn ects on One Optic al Circuit Using Manual Routing DLP-D237 Roll Two Cross-Connects on O ne Optical Circuit Using Manual Routing Step 1 From the V iew men u, choose Go T o Network V iew . Step 2 Click the Circui ts tab . Step 3 Cli[...]

19-41 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D237 Roll Two Cross-Connects on One Optical Circuit Using Manual Routing Step 13 Set the circuit path protect ion: • T o route the circuit on a protected path, leav e Fully Protected Path check ed and continue with Step 14 . • T o create an unprotecte[...]

19-42 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D238 Roll Two Cross- Connects from One O ptical Circuit to a Secon d Optical Cir cuit Note Y ou cannot complete a ro ll if you cancel led the sibling roll. Y ou must complete the two rolls together . Step 20 For both manual an d automatic rolls, click Fin[...]

19-43 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D238 Roll Two Cross-Connects from One Op tical Circuit to a Second Optical Circuit Step 9 Complete one of the follo wing : • If multiple Roll Fro m paths exist, th e Select Roll From dialog box appears. Select t he path from which you want to rol l traf[...]

19-44 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D239 Delete a Roll DLP-D239 Delete a Roll Step 1 From the V iew men u, choose Go T o Network V iew . Step 2 Click the Circ uits > Rolls tabs. Step 3 Click the rolled circuit that you w ant to delete. Step 4 From the T ools menu, ch oose Circuits > D[...]

19-45 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D241 Clear an MS-SPRing Manual Ring Switch Step 1 From node or netw ork vie w , click the Cir cuits > Rolls tabs. Step 2 Click the rolled circuit that you w ant to cancel. Step 3 Click Cancel . Step 4 Return to your ori ginating procedure (NTP). DLP-D2[...]

19-46 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D242 Create an MS -SPRing on a Single Node DLP-D242 Create an MS-SPRing on a Single Node Step 1 In node vie w , click the Pr ovisioning > MS -SPRing tabs. Step 2 In the Suggestion dialog box, cli ck OK . Step 3 In the Create MS-SPRing dialog box, enter[...]

19-47 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D243 Create a VLAN DLP-D243 Create a VLAN Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 From the T ools menu, ch oose Manage VLANS . Step 3 In the All VLANs dialog box, click Cr eate . Step 4 In the Def ine Ne w VLAN dialog box , compl[...]

19-48 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D244 Use the Reinitialization Tool to Clea r the Database and Up load Software (Windows) DLP-D244 Use the Reinitialization Tool to Clear the Database and Upload Software (Windows) Caution Restoring a node to the f actory conf ig uration deletes all cross-[...]

19-49 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D244 Use the Re initializa tion Tool to Clear the Database an d Upload Software (Windows) • User ID—Enter the user ID needed to access the node. • Password—Enter the password for the user ID. • Upload Package—Check this box to send the softwar[...]

19-50 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D245 Use the Reinitialization Tool to Cl ear the Database and Upload Software (UNIX) DLP-D245 Use the Reinitialization Tool to Clear the Database and Upload Software (UNIX) Step 1 Insert the system so ftware CD containi ng the reinit tool, softw are, and [...]

19-51 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D246 Provision E-Series Ethernet Card Mode Step 5 Click Go . Caution Before continuing with t he next st ep, verify t hat the database to upload is corr ect. Y ou cannot rev erse the upload process after you click Y es. Step 6 Re vie w the information on [...]

19-52 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D247 Change an STM- N Card Step 6 Repeat Steps 1 through 5 for other nodes, as ne cessary . Step 7 Return to your ori ginating procedure (NTP). DLP-D247 Change an STM-N Card Caution Physically removing an STM-N card can cause a lo ss of working traf fi c [...]

19-53 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D248 Delete VLANs Step 5 Complete the “NTP-D16 Install STM-N Card s and Connectors” procedure on page 2-7 . Step 6 Return to your ori ginating procedure (NTP). DLP-D248 Delete VLANs Note VLANs in use will not be deleted. Step 1 From the V iew men u, c[...]

19-54 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D249 Provision IP Settings Step 2 Click the Pro visioning > Network > General tabs. Step 3 Complete the follo wing informati on in the f ields listed: • IP Address—T ype the IP address assigned to the ONS 154 54 SDH node. Note If TCC2P cards are[...]

19-55 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D249 Provision IP Settings • Net/Subnet Mask Length—T ype the subnet mask length (decimal number representin g the subnet mask length in bits) or click the arro ws to adjust th e subnet mask length. Th e subnet mask leng th is the same for all ONS 154[...]

19-56 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D249 Provision IP Settings Step 6 Click OK . The network vie w appears. The node icon appears in gray , during which time you cannot access the node. Step 7 Double-click the node icon when it b ecomes green. As necessary , complete the “DLP-D65 Create a[...]

19-57 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D250 Set Up or Change Open Shortest Path First Protocol DLP-D250 Set Up or Change Open Shortest Path First Protocol Step 1 In node vie w , click the Pr ovisioning > Netw ork > OSPF tabs. Step 2 On the top left side of the OSPF tab, complete the foll[...]

19-58 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D250 Set Up or Change Open Shortest Path First Protocol Step 5 Provision the OSPF pr iority and interv al settings: The OSPF priority and interv al defaults are ones most commonly used b y OSPF routers. V erify that these defaults match the ones used by t[...]

19-59 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D251 Set Up or Change Routing Information Protocol • Retransmit Int (sec)—Sets the time th at will elapse before a packet is resent. Fi ve seconds is the default. • Dead Int (sec)—Sets the number of seconds that will pass while an O SPF router’ [...]

19-60 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D254 TCC2/TCC2P Card Active/Standby Switch Test Step 6 If you want to complete an address summary , comp lete the following steps. If not, con tinue with Step 7 . Complete the address summary only i f the ONS 15454 SDH is a ga te way NE with multi ple ex [...]

19-61 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D255 Cross-Connect Card Side Switch Test Step 9 After the node ic on turns gree n (within 1 to 2 minutes), dou ble-click it. On t he shelf graphi c, observe the following: • The pre vious standby TCC2/TCC2P card has a green A CT LED. • The pre vious a[...]

19-62 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D256 View Ethernet Statistics PM Parameters Step 5 Click the Maintenance > Cross-Connect tabs. Step 6 In the Cross-Connect Cards area, make a note of the activ e and standb y slots. Step 7 On the shelf graphic, verify that the acti ve cross-connect car[...]

19-63 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D257 View Ethernet Utilizatio n PM Parameters Step 3 Click the Statistics subtab . Step 4 Click Refresh . Performance monitoring statistics appear for each port on the card. Step 5 V iew the PM parameter n ames in the P aram column. The current PM paramet[...]

19-64 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D258 View Ethernet History PM Parameters DLP-D258 View Ethernet History PM Parameters Step 1 In node vie w , double-click the E-Se ries or G-Series Ethernet card where you w ant to vie w PM counts. The card vie w appears. Step 2 Click the Perf ormance tab[...]

19-65 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D260 Set Auto-Refresh In terval for Displayed PM Counts • 15 min : This option displays the specif ied PM counts in fi fteen-minute time interv als. • 1 hour : This optio n displays th e specified PM coun ts in one- hour time i ntervals. • 1 day : T[...]

19-66 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D261 Refresh PM Counts for a Different Port DLP-D261 Refresh PM Counts for a Different Port Step 1 In node vie w , double-cl ick the STM-N card where you w ant to vie w PM counts. The card vi e w appears. Step 2 Click the Perf ormance tab . Step 3 In the [...]

19-67 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D262 Filter the Display of Circuits • Direction—Choose one to f ilter circui ts based on direction: An y (direction not used t o filt er circuits), 1-way (display only o ne-way circuits), or 2-way (display only two-way circuits). • OCHNC Di r—(DWD[...]

19-68 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D263 Edit S NCP Dual-Ring Inte rconnect Circuit Hold-Off Timer Step 5 Click OK . Circuits match ing the attrib utes in th e Filter Circuit s dialog box appear in th e Circuits wi n d ow . Step 6 T o turn filtering off, click the Filter ic on in the lower [...]

19-69 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D264 Provision a J1 Path Trace o n Circuit Source and Destination Ports DLP-D264 Provision a J1 Path Trace on Circuit Source and Destination Ports Note This task assumes that you are setting up path trace on a bidirectional circuit and sett ing up transmi[...]

19-70 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D264 Provision a J1 Path T race on Circuit Source and Destination Ports Note If neither port is on a transmi t/recei ve card , you will not be ab le to complete this p rocedure. If one port is on a transmit/recei ve card and the ot her is on a recei ve -o[...]

19-71 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D264 Provision a J1 Path Trace o n Circuit Source and Destination Ports d. (Check box visibility depends o n card selection) Click the Disable AIS on C2 Mis-Match check box if you w ant to suppress the A IS when a C2 mismatch occurs. e. Click Appl y , the[...]

19-72 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D265 Change the Login Legal Disclaimer When you di splay the de tailed circuit window , path trace is indicated b y an M ( manual path trace) or an A (automatic path trace) at the circuit source and destination p orts. Step 13 Return to your ori ginating [...]

19-73 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D266 Change IP Settings Step 4 Click Apply . Step 5 Return to your ori ginating procedure (NTP). DLP-D266 Change IP Settings Caution Changing the node IP address, subnet mask, or II OP listener port causes the TCC2/TCC2P cards to reboot. If Ethernet circu[...]

19-74 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D268 Apply a Custom Networ k View Backgr ound Map If you changed a netw ork f ield that will cause the no de to reboot, the Change Netw ork Conf iguration confi rmation dialog box appears. If you changed a g ate way setting, a con fir mation appropriate t[...]

19-75 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D269 Enable Dialog Bo x Do-Not-Display Option DLP-D269 Enable Dialog Box Do-Not-Display Option Note If any user who has righ ts to perfor m an operation (f or example, creating a circuit) selects the “Do not sho w this dialog again” check box on a dia[...]

19-76 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D271 Change Node Se curity Policy on a Single Node Step 2 If you want to modify th e idle user timeout period, click t he hour (H) and minut e (M) arro ws in the Idl e User T imeout area for the securit y lev el you w ant to pro vision: RETRIEVE, MAINTEN [...]

19-77 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D272 Change Node Security Poli cy on Multiple Nodes DLP-D272 Change Node Security Policy on Multiple Nodes Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 Click the Provisioning > Security > Policy tabs. A r ead-only table of nod e[...]

19-78 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D273 Modify SNMP Trap De stination • Disable Inacti v e User—If check ed, disables users wh o do not log into the nod e for the period of time specified i n the Inacti v e Duration box. The Inact i ve Dur ation range is 45 to 90 days. Step 9 In the Se[...]

19-79 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D293 Perform a Manual Span Upgrade on a Two-Fiber MS-SPRing Step 9 SNMP settings are no w co nf igured. T o view SNMP information f or each node, highligh t the node IP address in the T rap Destinations area of the SNMP windo w . Confirm that the chang es[...]

19-80 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D294 Perfor m a Manual Span Upgr ade on a Four-Fi ber MS-SPRing Step 10 When cards in both endpoi nt nodes ha v e been successfully upgraded and all the f acility alarms (LOS, SD, or SF) are cleared, remove the F orce switch fro m both end points on the u[...]

19-81 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D295 Perform a M anual Span Upgrade on an SNCP Step 8 V erify that the transmit signal f alls wit hin the acceptabl e range. See T able 2-4 on page 2-17 for STM-N card transmit and recei v e le v els. Step 9 Complete the “DLP-D338 Instal l Fiber -Optic [...]

19-82 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D296 Perfor m a Manual Span Up grade on a 1+1 Protec tion Group Step 10 Complete the “DLP-D198 Clear an SNCP Force Switch” task on page 18-85 when cards in bo th endpoin t nodes hav e been successfully upgraded and all th e facility alarms (LOS, SD, o[...]

19-83 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D297 Perform a Manual Spa n Upgrade on an Unprotected Span Step 9 V erify that the transmit signal f alls wit hin the acceptabl e range. See T able 2-4 on page 2-17 for STM-N card transmit and recei v e le v els. Step 10 Complete the “NTP-D19 Install Fi[...]

19-84 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D298 Check th e Network for Alar ms and Conditions Step 6 When you ha ve f inished Steps 3 through 5 for bo th nodes, install the ne w STM-N cards in both endpoints and attach the f iber to t he cards. W ait for the IM PR OPRMVL alarm to clea r and the ca[...]

19-85 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D299 Initiate an M S-SPRing Span Lockout DLP-D299 Initiate an MS-SPRing Span Lockout Caution T raf f ic is not protected during a span lockout. Step 1 From the V iew men u, choose Go to Network V i ew . Step 2 Click the Pro visioning > MS-SPRing tabs. [...]

19-86 Cisco ONS 15454 SDH Procedure Guide, R7.2 October 2007 Chapter 19 DLPs D200 to D299 DLP- D299 Initiate an MS-SPRing Span Lockout Step 6 From the File menu, choose Close . Step 7 Return to your ori ginating procedure (NTP).[...]