Casablanca Fan Company Nouvelle manual

N OUVELLE OWNERS MANUAL[...]

1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) • The blad es in each pack are m atched f or equ al[...]

2 Calculation of 32 ° Use th e tear-o ff Ceiling Angle T emplate card in serted in th e back of this m an ual, it provi des you with a simple ‘go’ or ‘no-g o’ for in stalling your f an on a sloped ceiling. SLOPED CEILING INST ALLA TIONS MOUNTING RECOMMEND A TIONS 7 ′ MINIMUM P ole Length Standard Standard 6 ″ 12 ″ 12 ″ 18 ″ 24 ?[...]

3 INST ALLA TION INSTRUCTIONS Unpacking: Bef ore assembling and installing y our ceiling fan, r emov e all parts fr om the shipping cartons and check them against the parts listed in instructions . Bef ore discar ding pack aging material, be certain that all parts have been r emoved. CEILING HARDW ARE[...]

4 AD APT OR PLA TE INST ALLA TION JOIST Step 2. Route the outlet bo x wires thr ough the 1 / 2 ″ diam- eter outer hole o f the can opy adaptor plate . Attach th e crossbar an d canopy ad aptor plate to outlet box with screws provi ded . Step 3. With the lar g e wash er attach ed , pass th e lag scr ew through th e cen ter hole o f canopy adaptor [...]

5 FAN PREP ARA TION - HARDW ARE TIP: Use m asking tape to tempor arily h old the m otor cover to the downr od ball; this will ease downr od installati on. FAN PREP ARA TION 2 Note: For the next 5 prepara- tion steps it is convenient to leave the fan body in the lower carton styrof oam as it provides a stable work-top. DOWNROD & BALL ASSEMBL Y P[...]

6[...]

7[...]

8 FEL T W ASHER (4 PER BLADE) BLADE SCREW (4 PER BLADE) Step 10. Attach th e blades to the blad e hold ers with four o f the flat h ead 10-24 X 9 / 16 ″ blad e screws an d #10 felt washers pr ovi ded . Ha nd tigh ten securely . BLADE & BLADE HOLDER INST ALLA TION BLADE HOLDER SCREW (2 PER BLADE HOLDER) BLADE HOLDERS & HARDW ARE BLADE HOLD[...]

9 Step 12. Remove th e wir e nuts on th e BLACK an d WHITE wires fr om the f an. If n ecessary r emove th e in sulation from th e last 1 / 2 ” o f each wire (f an an d li ght fixtur e). Step 14. Attach th e switch h ousing wir es to the li ght fixture wir es by placing th e bar e ends o f the wir es to- geth er and th en securin g with a wire n u[...]

10 Step 16. Install thr ee fing er screws in to each li gh t fitter . T urn only once or twi ce . Step 17. P osition th e shad e fully in the fitter an d tigh ten each fing er scr ew two turns each in rotati on until th e shade is cen tered in th e fit- ter . Ch eck that the shad e is captured by th e fing er screws by ligh tly pulling on th e shad[...]

11 NO LIGHT FIXTURE OPTION - HARDW ARE ASSEMBL Y NO LIGHT FIXTURE OPTION - HARDW ARE LOWER SWIT CH HOUSING CAP THREADED BUTTON Step 20. Line up th e center holes o f the cap an d lower switch housin g to allow th e thread ed button to be installed. Hand tigh ten secur ely NO LIGHT FIXTURE OPTION - INST ALLA TION NO LIGHT FIXTURE OPTION - INST ALLA [...]

INTELI•TOUCH ♦ ♦ ♦ ♦ ♦ SINGLE W -32 INST ALLA TION The wall con trol in stalls in the same m anner as an ordinary li ght switch, using an e xisting juncti on box an d wirin g. This contr oller is design ed to si gnal the f an microcomputer as well as perf orm n orm al switchin g oper ations . For this r eason th e f ollowing pr ecaution[...]

13 INTELI•T OUCH OPERA TION ♦ POWER + + + + Progr ammed into every In teli-T ouch Series f an is an A uto- m atic Dem onstr ation Pr ogram. I t can be used to fully dem on strate an d test the oper ation o f the f an. T o enter the demonstration pr ogram: 1. T urn off f or at least three secon ds . This will clear the f an mem ory read y for pr[...]

14 Th e Ligh t-Minder pr ogram automati cally turns OFF th e f an moun ted ligh ts after two hours . T o enter the Light-Minder Progr am: 1. T urn th e OFF f or at least three secon ds. 2. T urn th e ON. 3. Immedi ately operate the button s in the f ollowing sequen ce: + + + 4. A series o f tones indi cates this comman d has been accepted. Th e fan[...]

15 TROUBLESHOO TING Befor e Requesting Service: Please follo w this troubleshooting guide bef ore contacting y our dealer for assist ance . Caring for Finishes : For cleanin g, a soft brush or lin t-free cloth should be used to pr event scr atchin g the finish. A vacuum clean er brush nozzle can r emove h eavier dust. Surf ace smud ges or an accu- [...]

17 ©COPYRIGHT 2000 CASABLANCA FAN COMPANY • U.S. PATENT PENDING PRINTED IN ROC 761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-CASA-1ST (227-2178) www.CasablancaFanCo.com[...]