Bissell 37N1 manual

2 Thank Y ou USER'S GUIDE 37N1 SERIES 220-240V Safe ty Instr uctions Product Vie w Assembly Operations Maintenance and Car e T roubleshoo ting R eplacement Parts 3 4 5 6-7 8-12 13 14 W arranty Consumer Services 15 16[...]

www .bissell.com T hanks f or buying a BISSELL Clean view Compact Dual C y clonic W e’re glad you pur chased a BISSELL Cleanview Compact Dual Cyclonic vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Y our BISSELL Cleanview Compact Dual Cyclonic vacuum is well made[...]

When using an electrical appliance, basic precautions should be observed, including the follo wing: READ ALL INSTR UCTIONS BEF ORE USING Y OUR UPRIGHT V A CUUM. W ARNING : To reduce the r isk of fi re , electric shoc k, or injury: ■ Do not use outdoors or on wet surfaces. ■ Do not leave machine when it is plugged in. ■ Do not use with damaged[...]

www .bissell.com 4 P roduct view CAUTION: Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures. *The Filter Media, not the vacuum as a whole, complies with the High Efficiency Par ticulate Air (HEP A) filter specification (EN 1822-1:2009). Handle Crevice T ool Dusting/ Upholster y T ool Hose W and[...]

www .bissell.com A ssembly The only tool you’ll need to assemble your vacuum is a screwdriver . Attach handle to vacuum 1. Locate the vacuum handle and remove the screw packet taped to the handle. 2. Stand the vacuum upright and from the rear of the unit, slide the base of the handle firmly into the grooves at the top of the vacuum body . 3. Ensu[...]

www .bissell.com O perations 6 Power Switch T he power switch is located on the left side of the vacuum. Push the rocker switch “ON” (1) to vacuum, and “OFF” (0) when cleaning is complete. Handle position Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three clean[...]

www .bissell.com 7 O perations Special tools Y our vacuum is not only a power ful carpet and rug vacuum cleaner , it’ s also a versatile above floor vacuum cleaner when you select one of the special tools. 1. Raise handle to upright position. 2. Remove hose from hose wand base. 3. Attach one of the tools by firmly pushing it onto the vacuum hose.[...]

www .bissell.com M aintenance and care 8 T o maximize your cleaning per for - mance and extend the life of your vacuum, it is very impor tant that you empty your dirt container and check and clean your filters frequently . Perform the following maintenance steps 1. Empty the dirt container when the dir t reaches the “full” line on the dirt con-[...]

www .bissell.com 9 M aintenance and care 1. Unplug the vacuum from electrical outlet. 2. The foam motor filter protects the motor from dirt par ticles. It is located in the slide out tray underneath the dir t con- tainer . If the filter becomes dirty , pull out the tray , lift out the foam filter pad and clean it. NOTE: The foam motor filter may be[...]

www .bissell.com M aintenance and care 10 Y ou should check your vacuum cleaner ’ s rotating floor brush and drive belt regu - larly for wear or damage. Y ou should also clean the brush and brush ends of strings, hair and carpet fibers. This type of debris can wrap around the brush and hamper its ability to effectively clean your carpet. Also rem[...]

www .bissell.com 11 M aintenance and care Replace drive belt 1. Unplug the vacuum from electrical outlet. 2. With rotating floor brush removed from vacuum cleaner (refer to page 10, steps 1-4 of check rotating floor brush and drive belt), grasp old drive belt and remove from motor pulley . Discard the old drive belt. 3. Place new drive belt over mo[...]

www .bissell.com M aintenance and care 12 Clearing clog Low suction, poor pickup or no suction may be due to a clog in the vacuum cleaner . If you notice a change in the sound of the vacuum motor , check for clogs. 1. T urn power switch off. Unplug cleaner from electrical outlet. 2. Empty dirt container . 3. Check upper tank for build up or clogs. [...]

www .bissell.com 13 T roubleshooting W ARNING: T o reduce the risk of electric shock, turn power OFF and dis - connect plug from electrical outlet before perfor ming maintenance or troubleshooting. V acuum cleaner won’ t turn Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Damaged power cord 2. Unplug, check for [...]

Item Part No. Part Name 1 203-2166 Dirt Container 2 203-2165 Hose 3 203-2171 Foam Motor Filter 4 203-2172 HEP A Media Filter* 5 203-2164 Crevice T ool 6 203-1527 Dusting Brush/Upholster y T ool www .bissell.com R eplacement parts - 14 1 6 2345 *The Filter Media, not the vacuum as a whole, complies with the High Efficiency Particulate Air (HEP A) fi[...]

www .bissell.com 15 W arr anty - BISSELL Cle anV ie w ™ Multi Cy clonic V acuum This warranty gives you specific legal rights, and you may also have other rights which may var y from countr y to countr y . If you need additional instruction regarding this warranty or have questions regarding what it may cover , please contact BISSELL Consumer Ser[...]

©2011 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 110-4361 Rev 3/11 Visit our website at: www .bissell.com B ISSELL consumer services www .bissell.com 16 If your BISSELL product should require service: Call BISSELL Consumer Ser vices at the numbers below and we will give you the location of a BISS[...]