Abit LG95C manual

LG-95Z V2.0 LG-95C Motherboard Intel Socket 775 Installation Guide[...]

ii LG-95Z V2.0/LG-95C Copyright and Warranty Notice The information in thi s document is sub ject to change witho ut notice and does not represent a commitmen t on part of the vend or, who assumes no liability or responsibility for any errors that may appe ar in this manual. No warranty or representation, either expressed or implied, is ma de w ith[...]

LG-95Z V2.0/LG-95C iii Contents 1. Hardware Setup ................................................ 1 1.1 Specif ications ............................................................. 1 1.2 Choosing a Comp uter Ch assis...................................... 2 1.3 Installing Motherboard ................................................ 2 1.4 Checking [...]

iv LG-95Z V2.0/LG-95C LG-95Z V2.0 Layout LG-95C Layout ※ The motherboard and its com ponent layouts illustrated in t he following chapter of this manual were mainly based on model “LG-95Z V2.0”, unless specifically stat ed.[...]

LG-95Z V2.0/LG-95C 1 1. Hardware Setup 1.1 Specifications CPU • LGA775 socket for Intel Core 2 Duo / Pentium Dual- Core / Pentium D / Pentium 4 / Cel eron D processor with 800MHz FSB • Supports Intel Hyper-Threading Technolo gy Chipset • LG-95Z V2.0: Intel 945GZ / ICH7 • LG-95C: Intel 945GC / ICH7 Memory • 2x 240-pin DIMM slots support up[...]

2 LG-95Z V2.0/LG-95C 1.2 Choosing a Computer Chassis • Choose a chassi s big enough to ins tall this mo therboard. • As some features for th is mo therboard are implemented by cabling connectors o n the motherboard to in dicators and switches or buttons on th e chassis, make sure your chass is supports all the features required. • I f t h e r[...]

LG-95Z V2.0/LG-95C 3 1.4 Checking Jumper Settings For a 2-pin jumper, plug t he jumper cap on both pins will make it C L O S E ( S H O R T ) . R e m o v e t h e j u m p e r c a p , o r p l u g i t o n e i t h e r p i n (reserved for future use) will leave it at OPEN position. SHORT OPEN OPEN For a 3-pin jumper, pin 1~2 or pin 2~3 c an be shorted by[...]

4 LG-95Z V2.0/LG-95C or “ CMOS checksum error ” displays on monitor, this backup battery is no longer functional and has to be renewed. To renew the backup battery: 1. Power off the system and disconnect with AC power source. 2. Remove the exhausted battery. 3. Insert a new CR2032 or equivalent batt ery. Pay attention to its polarity. The “ +[...]

LG-95Z V2.0/LG-95C 5 1.5.2 Front Panel Switches and Indicators Headers This header is used for connect ing switches and LED indicators on the chassis front panel. Watch the power LED pin posi tion and orientation. The mark “+” align to the pin in the figure belo w stands for positive polari ty for the LED connectio n. Please pay attention when [...]

6 LG-95Z V2.0/LG-95C 1.6 Installing Hardware ※ DO NOT scratch the motherboard when installing hardware. An accidental scratch of a tiny surfa ce-mount component may seriously damage the motherboard. ※ In order to protect the contact pi ns, please pay atte ntion to these notices: 1. A maximum 20 cycl es of CPU installa tion is recommended. 2. Ne[...]

LG-95Z V2.0/LG-95C 7 5. Use your left hand to hold the load plate, and use your right thumb to peel the cap off. ※ The cap plays an important role in protecting contact pins. In order to prevent bent pin, PUT ON the cap after operation or testing. 6. Lower the plate onto the CPU package. Engage the load lever while gently pressing down t he load [...]

8 LG-95Z V2.0/LG-95C 1.6.2 DDR2 Memory Slots • To reach the optimum perf ormance in dual-channel configurations, install identical DDR2 DIMM p airs for each channel. • Install DIMMs with the same CAS latency. To reach the optim um compatibility, obtain memory m odules from the same vendor. ※ Usually there is no hardware or BIOS setup required[...]

LG-95Z V2.0/LG-95C 9 1.7 Connecting Peripheral Devices 1.7.1 Floppy and IDE Disk Drive Connectors Connect the single end a t the longer length of rib bon cable to the FDD on the board, the two con nectors on the oth er end to the floppy disk drives connector. Generally you need only one floppy dis k drive in your system. ※ The red line on the rib[...]

10 LG-95Z V2.0/LG-95C 1.7.3 Additional USB 2.0 Port Headers Each header supports 2x additional USB 2. 0 ports by co nnecting bracket or cable to the rear I/O panel or the front-mou nted USB ports of your chassis. Pin Pin Assignment Pin Pin Assignment 1 VCC 2 VCC 3 Data0 - 4 Data1 - 5 Data0 + 6 Data1 + 7 Ground 8 Ground 10 NC ※ Make sure the conne[...]

LG-95Z V2.0/LG-95C 11 1.7.5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. Pin Signal Name Function 1 AUD_MIC Front Panel Microphone input signal 2 AUD_GND Ground used by Analog Audio Circuits 3 AUD_MIC_BIAS Microphone Power 4 AUD_VCC Filtered +5V used by Analog Audio Circuits 5 AUD_F_R Ri[...]

12 LG-95Z V2.0/LG-95C 1.8 Connecting Rear Panel I/O Devices The rear I/O part of this mo therboard provides the f ollowing I/O ports: • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • LPT1: Connects to printer or o ther devices that sup port this communication protocol. • COM1: Connects to external mode m, mouse or o[...]

LG-95Z V2.0/LG-95C 13 2. BIOS Setup This motherboard prov ides a programmable EEPROM so that you can u p d a t e t h e B I O S u t i l i t y . T h e B I O S ( B a s i c I n p u t / O u t p u t S y s t e m ) i s a program that de als with the ba sic level of com munication betw een processor and peripherals. Us e th e BIOS Setup program only when in[...]

14 LG-95Z V2.0/LG-95C 3. Driver & Utility The “Driver & Utili ty CD” that came packed wi th this motherboard contains drivers , utilities and s oftware applications requi red for its basi c and advanced features. Place the “Driver & Utility CD” i nto the CD-RO M drive in your system. The following installa tion auto-ru n screen [...]

LG-95Z V2.0/LG-95C 15 4. Appendix 4.1 規格（繁體中文） 處理器 • 支援具備 800MHz 前端匯流排的 Intel Core 2 Duo / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D 處理器 • 支援 Intel Hyper-Threading 技術 晶片組 • LG-95Z V2.0 ： Intel 945GZ / ICH7 • LG-95C ： Intel 945GC / ICH7 記憶體 • 2 條 240 針?[...]

16 LG-95Z V2.0/LG-95C 4.2 规格（简体中文） 处理器 • 支持具备 800MHz 前端总线的 Intel Core 2 Duo / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D 处理器 • 支持 Intel 超线程技术 芯片组 • LG-95Z V2.0 ： Intel 945GZ / ICH7 • LG-95C ： Intel 945GC / ICH7 内存 • 2 条 240 针脚 DIMM 插槽支持最?[...]

LG-95Z V2.0/LG-95C 17 4.3 Troubleshooting (How to Get Technical Support?) 4.3.1 Q & A Q: D o I need to clear the CMOS befo re I use a new motherbo ard to assemble my new computer system? A: Yes, we highly recommen d that you clear t he CMOS before install ing a new mothe rboard. Please move the CMOS jumper fro m its default 2-3 position to 1-2 [...]

18 LG-95Z V2.0/LG-95C Example: Memory bra nd: Kingston (KVR533D2N4/1G) • Memory size: Type in the size of your memory module . Example: 512M* 4PCS • Memory configuration: Type in the memory conf iguration in BIOS setting. Example: Memory Timing : 2.5-3-3-7 @533MHz • Graphics information: Note Graphics card’s brand, model and driver version [...]

LG-95Z V2.0/LG-95C 19 4.4 Contact Information Taiwan Head Office Universal ABIT Co., Ltd. 6F, No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan Tel: 886-2-8751-3380 Fax: 886-2-8751-3381 Sales: sales@abit.com.tw Marketing: market@abit.com.tw North America, South America Universal ABIT (U SA) Corporation 2901 Bayview Drive, Fremont, CA 94538, U.S.A[...]

P/N: 4310-0000-86 Rev. 3.00 http://www.abit.com.tw[...]