ZyXEL Communications ES-3148 manual

ES-3148 Intelligent Layer 2+ Switch 48-port Fast Ethernet + 2 Gigabit Ethernet Ports 2 GbE Dual Personality Interfaces (Copper/SFP) User ’ s Guide V ersion 3.70 8/2006 Edition 1[...]

[...]

ES-3148 User’s Guide Copyright 3 Copyright Copyright © 2006 by ZyXEL Communication s Corporation . The contents of this publication ma y not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into an y language, or transmitted in any fo rm or by any means, electronic, mechanical, magnetic, optical , ch[...]

ES-3148 User’s Guide 4 Certifications Certifications Federal Communications Commissi on (FCC) Interference St atement This device complies with Part 15 of FCC rules. Operation is subject to th e following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interferen[...]

ES-3148 User’s Guide Safety Warnings 5 Safety W arnings For your safety , be sure to read and fo llow all warning notices and instructions. • Do NOT use this p roduct near water , for example, in a wet basement or near a swimming pool. • Do NOT expose your device to dampness, dust or corrosive liquids. • Do NOT store thin gs on the device. [...]

ES-3148 User’s Guide 6 Safety Warnings This product is recyclable. Dispose of it properly .[...]

ES-3148 User’s Guide ZyXEL Limited Warranty 7 ZyXEL Limited W arranty ZyXEL warrants to the original end user (purchaser) th at this product is free from any defect s in materials or workmanship for a period of up to two yea rs from the date of purchase. During the warranty period, and upon proof of purchase, sh ould the product have indica tions[...]

ES-3148 User’s Guide 8 Customer Suppo rt Customer Support Please have the following information rea dy when you contact customer support. • Product model and serial number . • W arranty Information. • Date that you received your device. • Brief description of the problem an d the steps you took to solve it. METHOD LOCATION SUPPORT E-MAIL [...]

ES-3148 User’s Guide Customer Support 9 +” is the (prefix) number you enter to make an interna tional telephone call. NORWAY support@zyxel.no +47-22-80-61-80 www .zyxel.no ZyXEL Communications A/S Nils Hansens vei 13 0667 Oslo Norway sales@zyxel.no +47-22-80-61-81 POLAND info@pl.zyxel.com +48 (22) 333 8250 www .pl.zyxel.com ZyXEL Communications[...]

ES-3148 User’s Guide 10 Customer Suppo rt[...]

ES-3148 User’s Guide Table of Contents 11 T able of Content s Copyright .................................................. ................................................................ 3 Certifications ............................................ ................................................................ 4 Safety W arnings ..............[...]

ES-3148 User’s Guide 12 Table of Contents Chapter 3 Hardware Overview .................................. .............................................................. 47 3.1 Panel Connections ......................... ................. ................ ............. ................ .....47 3.1.1 Ethernet Ports ........ ............. ...........[...]

ES-3148 User’s Guide Table of Contents 13 Chapter 7 Basic Setting ........... ..................................................................................... ......... 73 7.1 Overview ......................... ................ ............. ................ ............. ................ ......... 73 7.2 System Inf ormation ................[...]

ES-3148 User’s Guide 14 Table of Contents 1 1.1.1 STP T erminology ........ ................ ................ ................ ................ .......... 107 1 1.1.2 How S TP Works .. ............. ................ ................ ................. ............ .......108 1 1.1.3 STP Port S tates ............................ ................ ..[...]

ES-3148 User’s Guide Table of Contents 15 Chapter 17 Port Security ....................................................... .................................................. 137 17.1 About Port Security ... ................ ................ ............. ................ ................ ....... 137 17.2 Port Security Setup ....... ..............[...]

ES-3148 User’s Guide 16 Table of Contents 22.1.3 IGMP Snooping ......... ................ ............. ................ ................ ............. 165 22.2 Multicast S tatus ......... ............. ................ ................ ............. ................ .......... 166 22.3 Multicast Setting .................. ................ ......[...]

ES-3148 User’s Guide Table of Contents 17 Chapter 27 Access Control ......................................... ..................................................... ....... 195 27.1 Access Control Overview .......... ................. ................ ................ ............. ...195 27.2 The Access Cont rol Main Screen ...... ...............[...]

ES-3148 User’s Guide 18 Table of Contents Chapter 32 ARP T able....................................................................... ....................................... 225 32.1 ARP T able Overview ........... ................ ................ ................ ............. ............. 225 32.1.1 How ARP Works ..... ................. ....[...]

ES-3148 User’s Guide Table of Contents 19 35.2.5 show mac address-table .. ................ ............. ................ ................ .......265 35.3 ping ........................... ................ ............. ................ ............. ................ .......... 266 35.4 traceroute ......... ................ ............. ........[...]

ES-3148 User’s Guide 20 Table of Contents 37.2.1 1 qos priority ......... ................ ............. ................ ............. ................ ....... 290 37.2.12 name ............... ................ ............. ................ ................ ................ ....... 291 37.2.13 speed-duplex ............... ................ ......[...]

ES-3148 User’s Guide Table of Contents 21 Appendix A Product Specifications ................................................................................. ....... 313 Appendix B IP Addresses and Subnetting ...................................................................... ....... 317 Index ..................................... ............[...]

ES-3148 User’s Guide 22 Table of Contents[...]

ES-3148 User’s Guide List of Figure s 23 List of Figures Figure 1 Backbone Application ............ .......... ................ ............. ................ .......... 38 Figure 2 Bridging Application ............ ... .......... ............. ................ ............. ............. 39 Figure 3 High Performance Switched Application ........[...]

ES-3148 User’s Guide 24 List of Figures Figure 39 Protocol Based VLAN ....... ................ ................ ................. ................ ... 96 Figure 40 Protocol Based VLAN Configurat ion Example ................... ................ ... 97 Figure 41 Port Based VLAN Setup (All Connected) .................... ................... ....... [...]

ES-3148 User’s Guide List of Figure s 25 Figure 82 S tatic Routing ................. ................ ................ ................ ................ ....... 181 Figure 83 DiffServ .......... ................ ............. ................ ................ ............. ............. 183 Figure 84 DiffServ .......... ................ .........[...]

ES-3148 User’s Guide 26 List of Figures[...]

ES-3148 User’s Guide List of Tables 27 List of T ables T able 1 Front Panel ..... ................ ............. ................ ................ ................ ............. 47 T able 2 Rear Panel ......... ................ ............. ................ ................ ................ .......... 50 T able 3 LEDs ........... ...............[...]

ES-3148 User’s Guide 28 List of Tables T able 39 Port Aut hentication: RADIUS . ................. ................ ................... ............. 133 T able 40 Port Aut hentication: 802.1x .......................... ................ ................ .......... 134 T able 41 Port Sec urity ....... ................ ................ .............[...]

ES-3148 User’s Guide List of Tables 29 T able 82 Configure C lone ..... ................ ................. ................ ................ ............. ... 228 T able 83 Command Interpret er Mode Summary ............ ................ .................... ... 233 T able 84 Command Summary: User Mode ....... ................ ................. ..[...]

ES-3148 User’s Guide 30 List of Tables[...]

ES-3148 User’s Guide Preface 31 Preface Congratulations on you r purchase of th e ES-3148 Intelligent Layer 2+ Switch. This preface introduces you to the ES-3148 and discusses the conventions of this User ’ s Guide. It also provides informatio n on other related documentation. About This U ser's Guide This manual is designed to guide you t[...]

ES-3148 User’s Guide 32 Preface Graphics Icons Key User Guide Feedback Help us help you. E-mail all User Guide-related comments, questions or suggestions for improvement to techwriters@zyxel.com.tw or send regular mail to The T echnical Writi ng T eam, ZyXEL Communications Corp., 6 Inno vatio n Road II, Science-Based Industrial Park, Hsinchu, 300[...]

ES-3148 User’s Guide Chapter 1 Getting to K now Your Switch 33 C HAPTER 1 Getting to Know Y our Switch This chapter introduces the main feat ures and applications of the switch. 1.1 Introduction The ES-3148 is a stand-alone layer 2+ Ethernet switch with 48 10/1 00Mbps ports, two RJ-4 5 Gigabit ports for stacking and 2 dual personality interfaces [...]

ES-3148 User’s Guide 34 Chapte r 1 Getting to Know Your Switch Queuing Queuing is used to help solv e performance degradation when there is network congestion. Three scheduling services are supported: Strict Priority Queuing (SP Q ), W eighted Round Robin (WRR) and W eighted Fair Schedule (WFS). This allows the switch to maintain separate queues [...]

ES-3148 User’s Guide Chapter 1 Getting to K now Your Switch 35 Port Authentication and Security For security , the switch allows authentication using IEEE 802.1x with an ex ternal RADIUS server and port security that allows only p ackets with dynamically learned MAC addresses and/or configured static MAC addres ses to pass through a port on the s[...]

ES-3148 User’s Guide 36 Chapte r 1 Getting to Know Your Switch IP Protoc ols • IP Host (No routing) • T elnet for configuration and mon itoring • SNMP for management • SNMP MIB II (RFC 1213) • SNMP v1 RFC 1 157 • SNMPv2, SNMPv2c or later version, compliant wi th RFC 201 1 SNMPv2 MIB for IP , RFC 2012 SNMPv2 MIB for TCP , RFC 2013 SNMP[...]

ES-3148 User’s Guide Chapter 1 Getting to K now Your Switch 37 1.3 Hardware Features This section describes the hardware features of the ES-3148. 48 10/100 Mbp s F ast Ethernet Port s Connect up to 48 comp uters or switches to the 10/100 Mbps auto-negotiating, automatic cable sensing (auto-MDIX) Ethernet RJ-45 ports. Mini-GBIC Slo t s Install SPF[...]

ES-3148 User’s Guide 38 Chapte r 1 Getting to Know Your Switch 1.4.1 Backbone Application In this application, the switch is an ideal solution for small ne two rks where rapid growth ca n be expected in the near future. The switch can be used stand alone for a group of heavy traffic users. Y ou can connect computers directly to the switch’ s po[...]

ES-3148 User’s Guide Chapter 1 Getting to K now Your Switch 39 Figure 2 Bridging Application 1.4.3 High Performance Switched Example The switch is ideal for connectin g two networks that need h igh bandwidth. In the followin g example, use trunking to connect these two networks. Switching to higher-speed LA Ns such as A T M (Asynchronous Transmis[...]

ES-3148 User’s Guide 40 Chapte r 1 Getting to Know Your Switch A VLAN (V irtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Stations on a logical network belong to on e group. A station can belong to more than one group. W ith VLAN, a stati on cannot directly talk to or hear from stations that a[...]

ES-3148 User’s Guide Chapter 1 Getting to K now Your Switch 41 Figure 5 Shared Server Using VLAN Example[...]

ES-3148 User’s Guide 42 Chapte r 1 Getting to Know Your Switch[...]

ES-3148 User’s Guide Chapter 2 Hardware Installation and Connection 43 C HAPTER 2 Hardware Inst allation and Connection This chapter shows you how to install and connect the switch. 2.1 Freest anding Inst allation 1 Make sure the switch is clean and dry . 2 Set the switch on a smooth, level surface st rong enough to support the weight of the swit[...]

ES-3148 User’s Guide 44 Chapter 2 Hardware Inst allation and Conne ction 2.2 Mounting the Switch on a Rack This section lists the rack mounting requirements and precautions and describes the installation steps. 2.2.1 Rack-mounted Installation Requirement s • T wo mounting brackets. • Eight M3 flat head screws and a #2 Philips screwdriver . ?[...]

ES-3148 User’s Guide Chapter 2 Hardware Installation and Connection 45 Figure 8 Mounting the Switch on a Ra ck 2 Using a #2 Philips screwdriver , install the M5 flat head screws through the mounting bracket holes into the rack. 3 Repeat steps 1 and 2 to attach the second mounting bracke t on the other side of the rack.[...]

ES-3148 User’s Guide 46 Chapter 2 Hardware Inst allation and Conne ction[...]

ES-3148 User’s Guide Chapter 3 Hardware Overview 47 C HAPTER 3 Hardware Overview This chapter describes the front panel a nd rear pa nel of the switch and shows you how to make the hardware conn ections. 3.1 Panel Connections The figure below shows the fro nt panel of the switch. Figure 9 Front Panel The following table describes the ports on the[...]

ES-3148 User’s Guide 48 Chapter 3 Hardware Overview There are two pairs of Gigabit Ethernet/mini-GB IC ports. The mini-GBI C ports have priority over the Gigabit port s . This means that if a mini-GBIC port and the corresponding Gi gabit port are connected at the same time, the Gigabit port will be disabled. The spee d of the Gigabit Ethernet/min[...]

ES-3148 User’s Guide Chapter 3 Hardware Overview 49 Figure 10 T ransceiver Installation Example 2 Press the transceiver firmly until it clicks into place. 3 The switch automatically detects the installed transceiver . Check the LEDs to verify that it is functioning properly . Figure 1 1 Installed T ransceiver 3.1.2.2 T r anscei ver Remova l Use t[...]

ES-3148 User’s Guide 50 Chapter 3 Hardware Overview 3.2 Rear Panel The following figure shows th e rear panel of the ES-3148. Figure 14 Rear Panel The following table describes the ports on the panels. 3.2.1 Console Port For local management, you can use a computer w ith terminal emulation software configured to the following parameters: • VT10[...]

ES-3148 User’s Guide Chapter 3 Hardware Overview 51 3.2.2 External Backup Power Supply Connector The switch supports extern al backup power supply (BPS). The backup power supply co nstantly monitors the status of the internal power supply . The backup power supply automatically provides po wer to the switch in the event of a power failure. Once t[...]

ES-3148 User’s Guide 52 Chapter 3 Hardware Overview LNK/ACT Green Blinking The system is transmitti ng/receiving to/from a 10 Mbps or a 1000 Mbps Ethernet network. On The link to a 10 Mbps or a 1000 Mbps Ethernet network is up. Amber Blinking The system is transmitting/r eceiving to/from a 100 Mbp s Ethernet network. On The link to a 100 Mbps Eth[...]

ES-3148 User’s Guide Chapter 4 The Web Configurator 53 C HAPTER 4 The W eb Configurator This section introduces the con figuration and functions of the web configurator . 4.1 Introduction The web configu rator is an HTML-based ma nage ment interface that allows easy switch setup and management via Interne t browser . Use In ternet Explorer 6.0 an[...]

ES-3148 User’s Guide 54 Chapter 4 The Web Configurator 4 Click OK to view the first web configurator screen. 4.3 The St atus Screen The St a t u s screen is the first screen that displa ys when yo u access the web config urator . The following figure shows the navigat ing co mponen ts of a web configurator screen. Figure 16 Web Configura tor Home[...]

ES-3148 User’s Guide Chapter 4 The Web Configurator 55 4.4 Menu Overview In the navigation panel, click a main l ink to reveal a list of submenu links. Table 4 Navigation Panel Sub-links Overview BASIC SETTING ADVANCED APPLICATION ROUTING PROTOCOL MANAGEMENT[...]

ES-3148 User’s Guide 56 Chapter 4 The Web Configurator The following table lists the various web configurator screens within the sub-links. Table 5 Web Configurator Screen Sub- links Details BASIC SETTING ADVANCED APPLICATION ROUTING PROTOCOL MANAGEMENT System Info General Setup Switch Setup IP Setup Port Setup VLAN VLAN S tatus VLAN Port Setting[...]

ES-3148 User’s Guide Chapter 4 The Web Configurator 57 The following table describes the links in the navigation panel. Table 6 Navigation Panel Links LINK DESCRIPTION Basic Settings System Info This link t akes you to a screen that displays general system and hardware monitoring information. General Setup This link takes you to a screen w here y[...]

ES-3148 User’s Guide 58 Chapter 4 The Web Configurator 4.4.1 Change Y our Password After you log in for the first time, it is reco mmended y ou change the default admin istrator password. Click Management , Access Control and then Logins to display the next screen. Routing Protocol S tatic Routing This link takes you to screens wher e you can con[...]

ES-3148 User’s Guide Chapter 4 The Web Configurator 59 Figure 17 Change Administr ator Login Password 4.5 Saving Y our Configuration When you are done mo difying the settings in a screen, click Apply to save your changes back to the run-time memory . Settings in the run-time memory are lost when the ES-3148’ s power is turned off. Click the Sav[...]

ES-3148 User’s Guide 60 Chapter 4 The Web Configurator 6 Forg etting the password and/or IP address. 7 Preventing all services from accessing the switch. 8 Changing a service port number but for getting it. Note: Be careful not to lock yourself and others out of the switch. T ry using the out-of-band management port before resetting the switch. T[...]

ES-3148 User’s Guide Chapter 4 The Web Configurator 61 Figure 18 Example Xmodem Upload 7 After a configuration file upload, type atgo to restart the switch. Figure 19 Reload the C onfiguration file: Via Console Po rt The switch is now reinitialized with a default configuration file including the default password of “1234”. 4.7.2 Reset to the [...]

ES-3148 User’s Guide 62 Chapter 4 The Web Configurator 4 Ty p e atbr after the " Enter Debug Mode " message. Figure 20 Resetting the Switch: V ia the Console Port 5 After the resetting, type atgo to restart the switch. 4.8 Logging Out of the W eb Configurator Click Logout in a screen to exit the web configurator . Y ou have to log in wi[...]

ES-3148 User’s Guide Chapter 5 Initial Setup Example 63 C HAPTER 5 Initial Setup Example This chapter shows how to set up the switch for an example network. 5.1 Overview The following lists the configuration steps for the initial setup: • Create a V LAN • Set port VLAN ID • Configure the switch IP management address 5.1.1 Creating a VLAN VL[...]

ES-3148 User’s Guide 64 Chapter 5 Initial Setup Example 1 Click Advanced App lication and VLAN in the navigation panel and click the St a t i c VLAN link. 2 In the S tatic VLAN screen, select ACTIVE , enter a descriptive name in the Name field and enter 2 in the VLAN Group ID field for the VLAN2 network. Note: The VLAN Group ID field in this scre[...]

ES-3148 User’s Guide Chapter 5 Initial Setup Example 65 Figure 23 Initial Setup Network Example: Port VID 1 Click Advanced App lications and VLAN in the navigation panel. Then click the VLAN Port Setting link. 2 Enter 2 in the PVID field for port 1 and clic k Apply to save your changes back to the run-time memory . Settings in the run-time memory[...]

ES-3148 User’s Guide 66 Chapter 5 Initial Setup Example 3 Click Basic Setting and IP Setup in the navigation panel. 4 Configure the related fields in the IP Setup screen. For the VLAN2 network, enter 192.168.2.1 as th e IP address and 255.255.255 .0 as the subnet mask. 5 In the VID field, enter the ID of the VLAN gr oup to which you want this man[...]

ES-3148 User’s Guide Chapter 6 Syst em Status an d Port Statist ics 67 C HAPTER 6 System S t atus and Port S t atistics This chapter describes the system status (web configurator ho me page) and port details screens. 6.1 Port S tatus Summary The home screen o f the web configurator dis plays a port statistical summary table with links to each por[...]

ES-3148 User’s Guide 68 Chapter 6 System Status and Port Statistics 6.1.1 St atus: Port Det ails Click a number in the Port column in the St a t u s screen to display indivi dual port statistics. Use this screen to check status and detailed performance data about an individual port on the switch. Link This field disp lays the speed (either 10M fo[...]

ES-3148 User’s Guide Chapter 6 Syst em Status an d Port Statist ics 69 Figure 26 S tatus: Port Details The following table describes the labels in this screen. Table 8 Status: Port Details LABEL DESCRIPTION Port Info Name This field shows the name of the port. Link This field shows whether the Ethernet connection is down, and th e speed/duplex mo[...]

ES-3148 User’s Guide 70 Chapter 6 System Status and Port Statistics LACP This field shows if LACP is enabled on this port or not. TxPkts This field shows the number of transmitted frames on this port RxPkts This field shows the number of received frames on this port Errors This field shows the number of receive d errors on this port. Tx KB/s This[...]

ES-3148 User’s Guide Chapter 6 Syst em Status an d Port Statist ics 71 64 This field shows the number of packet s (including bad packets) received that were 64 octets in length. 65-127 This field shows the number of packets (including bad packets) received that were between 65 and 127 octets in length. 128-255 This field shows the number of packe[...]

ES-3148 User’s Guide 72 Chapter 6 System Status and Port Statistics[...]

ES-3148 User’s Guide Chapter 7 Basic Setting 73 C HAPTER 7 Basic Setting This chapter describes how to configure the System Info, General Setup , Switch Setup , IP Setup and Port Setup screens. 7.1 Overview The System Info screen displays general switch info rmation (such as fi rmware version number) and hardware polling inform ation (such as fan[...]

ES-3148 User’s Guide 74 Chapter 7 Basic Setting Figure 27 System Info The following table describes the labels in this screen. Table 9 System Info LABEL DESCRIPTION System Name This field displays the descriptive name of the switch for identificati on purposes. ZyNOS F/W Ve r s i o n This field displays the versio n number of th e switch ' s[...]

ES-3148 User’s Guide Chapter 7 Basic Setting 75 7.3 General Setup Use this screen to configure general settings such as the system name and time. Cl ick Basic Setting and General Setup in the navigation panel to di splay the screen as shown. F AN speed (RPM) A properly functioning fan is an essentia l component (along with a sufficiently ventilat[...]

ES-3148 User’s Guide 76 Chapter 7 Basic Setting Figure 28 General Setup The following table describes the labels in this screen. Table 10 General Setup LABEL DESCRIPTION System Name Choose a descriptive name for identification purposes. This name consists of up to 64 printable characters; spaces are allowed. Location Enter the geogra phic locatio[...]

ES-3148 User’s Guide Chapter 7 Basic Setting 77 7.4 Introduction to VLANs A VLAN (V irtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Device s on a logical network belong to one group. A device can belong to more than one group. W ith VLAN, a device cannot directly talk to or hear from devices [...]

ES-3148 User’s Guide 78 Chapter 7 Basic Setting Note: VLAN is unidirectional; it only govern s outgoing traf fic. See Chapter 8 on pa ge 87 for information on port-ba sed and 802.1Q tagged VLANs. 7.5 Switch Setup Screen Click Basic Setting and then Switch Setup in the navigation panel to display the scree n as shown. The VLAN setup screens ch ang[...]

ES-3148 User’s Guide Chapter 7 Basic Setting 79 Aging T ime Enter a time from 10 to 3000 seconds. This is how long all dynamically lear ned MAC addresses remain in the MAC address table before they age out (a nd must be relearned). GARP T imer: Switches join VLANs by making a declaratio n. A declaration is made by issuing a Join message using GAR[...]

ES-3148 User’s Guide 80 Chapter 7 Basic Setting 7.6 IP Setup Use the IP Setup screen to configure the default gate way device, the default domain name server and add switch IP address. 7.6.1 Manage ment IP Addresses The switch needs an IP address for it to be mana ged over the network. The factory default IP address is 192.168.1.1. The subnet mas[...]

ES-3148 User’s Guide Chapter 7 Basic Setting 81 Figure 30 IP Setup[...]

ES-3148 User’s Guide 82 Chapter 7 Basic Setting The following table describes the labels in this screen. T able 12 IP Setup LABEL DESCRIPTION Domain Name Server DNS (Domain Name System) is for mapping a doma in name to its corresponding IP address and vice versa. Enter a d omain name server IP addre ss in order to be ab le to use a domain name i [...]

ES-3148 User’s Guide Chapter 7 Basic Setting 83 7.7 Port Setup Use this screen to configur e switch port settings. Click Basic Setting and then Port Setup in the navigation panel to enter the port configuration screen. Full-duplex mode oper ation only applies to poin t-to-point access (for example, when attaching the switch to a workstation, serv[...]

ES-3148 User’s Guide 84 Chapter 7 Basic Setting Figure 31 Port Setup The following table describes the labels in this screen. Table 13 Port Setup LABEL DESCRIPTION * Settings in this row apply to all ports. Use this row only if you want to make some settings the same for all ports. Use this row first to set the common settings and then make adjus[...]

ES-3148 User’s Guide Chapter 7 Basic Setting 85 Flow Control A concentration of traffic on a port decreases port bandwidth and overflows buffer memory causing packet discards and frame losses. Flow Contro l is used to regulate transmission of signals to match t he bandwi dth of the receiving port. The switch uses IEEE802.3x flow control in full d[...]

ES-3148 User’s Guide 86 Chapter 7 Basic Setting[...]

ES-3148 User’s Guide Chapter 8 VLAN 87 C HAPTER 8 VLAN The type of screen you see here depends o n the VLAN T ype you selected in the Switch Setup screen. This chapter shows you how to conf igure 802.1Q tagge d and port-based VLANs. 8.1 Introduction to IEEE 802.1Q T agged VLAN A tagged VLAN uses an explicit tag (VLAN ID) in the MAC header to iden[...]

ES-3148 User’s Guide 88 Chapter 8 VLAN 8.2 Automatic VLAN Registration GARP and GVRP are the protocols used to auto matically register VLAN membership acros s switches. 8.2.1 GARP GARP (Generic Attribute Registration Protocol) allows network switches to register and de- register attribute values with other GARP par ticipants within a brid ged LAN[...]

ES-3148 User’s Guide Chapter 8 VLAN 89 8.3 Port VLAN T runking Enable VLAN T runking on a port to allow frames belong ing to unknown VLAN groups to pass through that port. This is useful if yo u want to set up VLAN groups on end devices without having to configure the same VLAN groups on intermediary devices. Refer to the following figure. Suppos[...]

ES-3148 User’s Guide 90 Chapter 8 VLAN 8.5 St atic VLAN Use a static VLAN to decide whether an incoming frame on a port should be • sent to a VLAN group as normal d epends on its VLAN tag. • sent to a group whether it has a VLAN tag or not. • blocked from a VLAN group regardless of its VLAN tag. Y ou can also tag all outgoing frames (that w[...]

ES-3148 User’s Guide Chapter 8 VLAN 91 8.5.2 St atic VLAN Det ails Use this screen to view detailed port se ttings and status of the VLAN group. See Section 8. 5 on page 90 for more information on static VLAN . Click on an index number in the VLAN St a t u s screen to display VLAN details. Figure 35 S tatic VLAN Details The following table descri[...]

ES-3148 User’s Guide 92 Chapter 8 VLAN Figure 36 VLAN: S tatic VLAN The following table describes the re lated labels in this screen. Table 17 VLAN: S tatic VLAN LABEL DESCRIPTION ACTIVE Select this check box to activate the VLA N settings. Name Ente r a descriptive name fo r the VL AN group for identification purposes. VLAN Group ID Enter the VL[...]

ES-3148 User’s Guide Chapter 8 VLAN 93 8.5.4 Configure VLAN Port Settings Use the VLAN Port Setting screen to configure the static VLAN (IEEE 802.1Q) settings on a port. See Section 8.5 on page 90 for more information on static VLAN. Click the VLAN Port Setting link in the VLAN S tatus screen. Figure 37 VLAN: VLAN Port Setting Add Click Add to sa[...]

ES-3148 User’s Guide 94 Chapter 8 VLAN The following table describes the labels in this screen. Table 18 VLAN: VLAN Port Setting LABEL DESCRIPTION GVRP GVRP (GARP VLAN Registration Protocol) is a registration protocol that defines a way for switches to register necessary VLAN memb ers on ports across the network. Select this check box to permit V[...]

ES-3148 User’s Guide Chapter 8 VLAN 95 8.6 Protocol Based VLANs Protocol based VLANs allow you to group traffi c into logical VLANs based on the protocol you specify . When an upstream frame is receive d on a port (configured fo r a protocol based VLAN), the switch checks if a tag is added already and its protocol. The untagged packets of the sam[...]

ES-3148 User’s Guide 96 Chapter 8 VLAN Figure 39 Protocol Based VLAN The following table describes the labels in this screen. Table 19 Protocol Ba se d VLAN Setup LABEL DESCRIPTION Active Check thi s box to activate this protocol based VLAN. Port T ype a port to be included in this protocol based VLAN. This port must belong to a static VLAN in or[...]

ES-3148 User’s Guide Chapter 8 VLAN 97 8.8 Create an IP-based VLAN Example This example shows you how to create an IP VLAN which includes ports 1, 4 and 8. Follow these steps: 1 Activate this protocol based VLAN. 2 T ype the port numb er you want to include in this protoco l based VLAN. T yp e 1 . 3 Give this protocol-based VLAN a desc riptive na[...]

ES-3148 User’s Guide 98 Chapter 8 VLAN 2 Change the value in the Port field to the next port you want to add. 3 Click Add . 8.9 Port-based VLAN Setup Port-based VLANs are VLANs where the packet forwarding de cision is based on the destination MAC address and its associated port. Port-based VLANs require allowed outgoing ports to be defined for ea[...]

ES-3148 User’s Guide Chapter 8 VLAN 99 Figure 41 Port Based VLAN Se tup (All Conn ected)[...]

ES-3148 User’s Guide 100 Chapter 8 VLAN Figure 42 Port Based VLAN Setu p (Port Isolation)[...]

ES-3148 User’s Guide Chapter 8 VLAN 101 The following table describes the labels in this screen. Table 20 Port Based VLAN Setup LABEL DESCRIPTION Setting Wizard Choose All connected or Port isolation . All connected means all ports can communicate with each other , that is, there are no virtual LANs. All incoming and outgoing ports are selected. [...]

ES-3148 User’s Guide 102 Chapter 8 VLAN[...]

ES-3148 User’s Guide Chapter 9 Static MAC Fo rwarding 103 C HAPTER 9 S t atic MAC Forwarding Use these screens to configure static MAC address forwarding. 9.1 Configuring S t atic MAC Forwarding A static MAC address is an address that has been manually entered in the MAC address table. St atic MAC addresses d o not age out. Wh en you set up stati[...]

ES-3148 User’s Guide 104 Cha pter 9 Static MAC Forwar ding The following table describes the labels in this screen. Table 21 S tatic MAC Forw arding LABEL DESCRIPTION Active Select this check box to activate your rule. Y ou may te mporarily deactivate a rule without deleting it by clearing this check box. Name En ter a descriptive name for identi[...]

ES-3148 User’s Guide Chapter 10 Filtering 105 C HAPTER 10 Filtering This chapter discusses static IP and MAC address port filtering. 10.1 Configure a Filtering Rule Filtering means sifting traf fic going through the switch based on the sour c e and/or dest ination MAC addresses and VLAN group (ID). Click Advanced App lication and Filtering in the[...]

ES-3148 User’s Guide 106 Chapter 10 Filte ring Action Select Discard source to drop frame from the sour ce MAC address (specified in the MAC field). The switch can still send frames to the MAC address. Select D iscard destinatio n to drop frames to th e desti nation MAC a ddress (specified in the MAC address). The switch can still rece ive frames[...]

ES-3148 User’s Guide Chapter 11 S panning T ree Protoc ol 107 C HAPTER 11 S p anning T ree Protocol The switch supports Spanning T ree Protocol (S TP) and Rapid Spanning T ree Protocol (RSTP) as defined in the fo llowing standards. • IEEE 802.1D Span ning T ree Protocol • IEEE 802.1w Rap id Spanning T ree Protocol The switch also allows you t[...]

ES-3148 User’s Guide 108 Chapter 11 Spa nning Tr ee Protocol On each bridge, the root port is the port thro ugh which this bridge communicates with the root. It is the port on this switch with the lowest path cost to the root (the root path cost). If there is no root port, then this switch has been accepte d as the root bridge of the spanning tre[...]

ES-3148 User’s Guide Chapter 11 S panning T ree Protoc ol 109 1 1.1.4 Multiple RSTP MRSTP (Multiple RSTP) is ZyXEL ’ s proprietary feature that is comp atible with RSTP and STP . W ith MRSTP , you can have more than one spanning tree on your switch and assign port(s) to each tree. Each spanning tree operates independently with its own bridge in[...]

ES-3148 User’s Guide 110 Chapter 11 Spa nning Tr ee Protocol Figure 46 S panning T ree Protocol RSTP and MRSTP The following table describes the labels in this screen. 1 1.3 Configure Rapid Sp a nning T ree Protocol Use this screen to configure RSTP settings, see Section 11.1 on page 107 for more information on RSTP . Click RSTP in the Advanced A[...]

ES-3148 User’s Guide Chapter 11 S panning T ree Protoc ol 111 Figure 47 RSTP: Configu ration The following table describes the labels in this screen. Table 26 RSTP: Confi guration LABEL DESCRIPTION S tatus Click Status to display the RSTP Statu s screen (see F igure 48 on page 1 13 ). Active Select this check box to activat e RSTP . Clear thi s c[...]

ES-3148 User’s Guide 112 Chapter 11 Spa nning Tr ee Protocol 1 1.4 Rapid Sp anning T r ee Protocol St atus Click Advanced Appli cation , Spanning T r ee Protocol in the navigation panel to display the status screen as shown next. See Section 1 1.1 on page 107 for more information on RSTP . Note: This screen is only available af ter you activate R[...]

ES-3148 User’s Guide Chapter 11 S panning T ree Protoc ol 113 Figure 48 Rapid S p anning T ree Protocol: St atus The following table describes the labels in this screen. 1 1.5 Configure Multiple Rapid Sp anning T ree Protocol T o configure MRSTP , select MRSTP in the Advanced Application , Spanning T ree Pro tocol screen. See Section 1 1.1 on pag[...]

ES-3148 User’s Guide 114 Chapter 11 Spa nning Tr ee Protocol Figure 49 MRSTP: Configuration The following table describes the labels in this screen. Table 28 MRSTP: Configuration LABEL DESCRIPTION S tatus Click Stat us to display the MRSTP St atus screen (see Figure 48 on page 1 13 ). T ree This is a read only index number of the STP tre es. Acti[...]

ES-3148 User’s Guide Chapter 11 S panning T ree Protoc ol 115 1 1.6 Multiple Rapid Sp anning T r ee Protocol St atus Click Advanced Appli cation , Spanning T r ee Protocol in the navigation panel to display the status screen as shown next. See Section 1 1.1 on page 107 for more information on MRSTP . Note: This screen is only available af ter y o[...]

ES-3148 User’s Guide 116 Chapter 11 Spa nning Tr ee Protocol Figure 50 MRSTP: S tatus The following table describes the labels in this screen. Table 29 S panning T ree Protocol: S tatus LABEL DESCRIPTION Configuration Click Configuration to configure MRSTP settings. Refer to Secti on 1 1.3 on page 11 0 . T ree Select which STP tree conf iguration[...]

ES-3148 User’s Guide Chapter 12 Bandwidth Control 117 C HAPTER 12 Bandwid th Control This chapter shows you h o w you can cap the max imum bandwidth using the Bandwidth Control screen. 12.1 Bandwid th Control Overview Bandwidth control mean s defining a maximum allowable bandwidth for incoming and/or out- going traf fic flows on a port. 12.1.1 CI[...]

ES-3148 User’s Guide 118 Chapter 12 Bandwidth Control Figure 51 Bandwidt h Control The following table describes the re lated labels in this screen. Table 30 Bandwidt h Control LABEL DESCRIPTION Active Select this check box to enable ban dwidth control on the switch. Port This field di splays the port number . * Settings in this row apply to all [...]

ES-3148 User’s Guide Chapter 12 Bandwidth Control 119 Apply Click Apply to save your changes to the switch’s run-time memory . The switch loses these changes if it is turned off or loses power , so use the Save link on the top navigation panel to save your changes to the non-volatile memory when you are done configuring. Cancel Click Cancel to [...]

ES-3148 User’s Guide 120 Chapter 12 Bandwidth Control[...]

ES-3148 User’s Guide Chapter 13 Broadcast Storm Control 121 C HAPTER 13 Broadcast S torm Control This chapter introduces and sh ows you how to configure t he broadcast storm control feat ure. 13.1 Broadcast S torm Control Setup Broadcast storm control limits the number of broadcast, multicast and destination lookup failure (DLF) packets the switc[...]

ES-3148 User’s Guide 122 Chapter 13 Broadcast Storm Control The following table describes the labels in this screen. Table 31 Broadcast S torm Control LABEL DESCRIPTION Active Select this check box to enable traffic storm control on the switch. Clea r this check box to disable this feature. Port This field displays a port number. * Settings in th[...]

ES-3148 User’s Guide Chapter 14 Mirroring 123 C HAPTER 14 Mirroring This chapter discusses the Mirror setup screens. 14.1 Port Mirroring Setup Port mirroring allows you to copy a traffic flow to a monitor port (the port you copy the traffi c to) in order that you can examine the traffi c from the monitor port without interference. Click Advanced [...]

ES-3148 User’s Guide 124 Chapter 14 Mirroring The following table describes the labels in this screen. Table 32 Mirroring LABEL DESCRIPTION Active Select this check box to activate port mirroring on the switch. Cle ar this check box to disable the feature. Monitor Port The monitor port is the port you copy the traffic to in order to examine it in[...]

ES-3148 User’s Guide Chapter 15 Link Aggregation 125 C HAPTER 15 Link Aggregation This chapter shows you how to logically aggreg ate physical links to fo rm one logical, higher - bandwidth link. 15.1 Link Aggregation Overview Link aggregation (trunking) is the grouping of physical ports into one logical higher-capacity link. Y ou may want to trun[...]

ES-3148 User’s Guide 126 Chapter 15 Link Aggregation 15.2.1 Link Aggregation ID LACP aggregation ID consists of the following information 1 : 15.3 Link Aggregation Control Protocol S t atus Click Advanced App lication , Link Aggr egation in the navigation panel. The Link Aggregation Control Pr otocol S t atus screen disp lays by default. See Sect[...]

ES-3148 User’s Guide Chapter 15 Link Aggregation 127 The following table describes the labels in this screen. 15.4 Link Aggregation Setup Click Configuration in the Link Aggr egation Control P rotocol S tatus screen to display the screen shown next. See Section 15.1 on page 125 for more informatio n on link aggregation. Table 35 Link Aggregation [...]

ES-3148 User’s Guide 128 Chapter 15 Link Aggregation Figure 55 Link Aggregation: Configuration The following table describes the labels in this screen. Table 36 Link Aggregation Control Protocol: Configur ation LABEL DESCRIPTION Link Aggregation Control Protocol Active Select this checkbox to enable Link Aggregati on Control Protocol (LACP). Syst[...]

ES-3148 User’s Guide Chapter 15 Link Aggregation 129 Group ID The field identifies the link ag gregation group , that is, one logical link containing multiple ports. Active Select this option to activate a trunk group. Dynamic (LACP) Select this check box to enable LACP for a trunk. Port This field displays the port number . * Settings in this ro[...]

ES-3148 User’s Guide 130 Chapter 15 Link Aggregation[...]

ES-3148 User’s Guide Chapter 16 Port Authentication 131 C HAPTER 16 Port Authentication This chapter describes the 802.1x authenti cation method and RADIUS server connection setup. See Section 36.9 on page 281 for information on how to u se the commands to configure additional Radius server settings as well as multiple Radius server configuration[...]

ES-3148 User’s Guide 132 Chapter 16 Por t Authent ication Note: Refer to the document ation that comes with your RADIUS server on how to configure a VSA. The following table describes the VSAs supported on the switch. 16.1.1.2 T unnel Pr otocol Attribute Y ou can configure tunnel protocol attributes on the RADIUS server to assign a port on the sw[...]

ES-3148 User’s Guide Chapter 16 Port Authentication 133 Click Advanced App lication , Port Authentication in the navigation pa nel to display the screen as shown. Figure 57 Port Authentication 16.2.1 Configuring RADI US Server Settings Use this screen to configure your RADIUS server settings. See Section 16.1.1 on page 131 for more information on[...]

ES-3148 User’s Guide 134 Chapter 16 Por t Authent ication 16.2.2 Activate IEEE 802.1x Security Use this screen to activate IEEE 802.1x security . From the Port Authentica tion screen, display the configuration screen as shown. Figure 59 Port Authentication: 802.1x The following table describes the labels in this screen. Table 40 Port Authenticati[...]

ES-3148 User’s Guide Chapter 16 Port Authentication 135 * Set tings in this row apply to all port s. Use this row only if you want to make some settings the same for all ports. Use this row first to set the common settings an d then make adjustments on a port-by-port basis. Note: Changes in this row are copied to all the port s as soon as you mak[...]

ES-3148 User’s Guide 136 Chapter 16 Por t Authent ication[...]

ES-3148 User’s Guide Chapter 17 Port Security 137 C HAPTER 17 Port Security This chapter shows you how to set up port security . 17.1 About Port Security Port security allows only packets w ith dynami cally learned MAC addresses and/or configured static MAC addresses to pass through a port on the switch. The switch can learn up to 16K MAC address[...]

ES-3148 User’s Guide 138 Chapter 17 Port Security Figure 60 Port Security The following table describes the labels in this screen. Table 41 Port Security LABEL DESCRIPTION Active Select th is option to enable port security on the switch. Port This field displays a port number . * Settings in this row apply to all ports. Use this row only if you w[...]

ES-3148 User’s Guide Chapter 17 Port Security 139 Apply Click Apply to save your changes to the switch’s run-time memory . The switch loses these changes if it is turned off or loses power , so use the Save link on the top navigation panel to save your changes to the non-vola tile memory when you are done configuring. Cancel Click Cance l to re[...]

ES-3148 User’s Guide 140 Chapter 17 Port Security[...]

ES-3148 User’s Guide Chapter 18 Classifier 141 C HAPTER 18 Classifier This chapter introduces and shows you how to configure the packet cl assifier on the switch. 18.1 About the Classifier and QoS Quality of Service (QoS) refers to both a networ k's ability to deliver data with minimum delay , and the networking methods used to control th e [...]

ES-3148 User’s Guide 142 Chapter 18 Classifier Figure 61 Classif ier The following table describes the labels in this screen. Table 42 Classifier LABEL DESCRIPTION Active Select this option to enable this rule. Name Enter a descriptive name for this rule fo r identifying purposes. Packet Format S pecify the format of the packet. Choices are All ,[...]

ES-3148 User’s Guide Chapter 18 Classifier 143 Layer 2 S pecify the fields below to configure a layer 2 classifie r . VLAN Select Any to classify traffic from any VLAN or select the second option and specify the source VLAN ID in the field provided. Priority Select Any to classify traffic from any prio rity leve l or select the second option and [...]

ES-3148 User’s Guide 144 Chapter 18 Classifier 18.3 V iewing and Editing Classifier Configuration T o view a summary of the classifier configuration, scroll down to th e summar y table at the bottom of the Clas sifier screen. T o change the settings of a rule, click a number in the Index field. Note: When two rules conflict with each other , a hi[...]

ES-3148 User’s Guide Chapter 18 Classifier 145 Some of the most common IP ports are: 18.4 Classifier Example The following figure shows an example where you configure a classifier that identifies all traffic from MAC address 00:50:ba:ad:4f:81 on port 2. Chaosnet 0804 X.25 Level 3 0805 XNS Compat 0807 Banyan Systems 0BAD BBN Simnet 5208 IBM SNA 80[...]

ES-3148 User’s Guide 146 Chapter 18 Classifier Figure 63 Classifier: Example[...]

ES-3148 User’s Guide Chapter 19 Policy Rule 147 C HAPTER 19 Policy Rule This chapter shows you how to configure policy rules. 19.1 Policy Rules Overview A classifier distinguishes traffic into flows based on the configured criteria (refer to Chapter 18 on page 141 for more information). A policy rule ensures that a traffic flow gets the requested[...]

ES-3148 User’s Guide 148 Chapter 19 Policy Rule 19.2 Configuring Policy Rules Y ou must first configure a classifier in the Classifier screen. Refer to Section 18.2 on page 141 for more information. Click Advanced App lications and then Policy Rul e in the navigation panel to display the screen as shown.[...]

ES-3148 User’s Guide Chapter 19 Policy Rule 149 Figure 64 Policy[...]

ES-3148 User’s Guide 150 Chapter 19 Policy Rule The following table describes the labels in this screen. Table 46 Policy LABEL DESCRIPTION Active Select this option to enabl e the policy . Name Enter a descriptive name for identification purposes. Classifier(s) This field displays the active classifier(s) you configu re in the Classifie r screen.[...]

ES-3148 User’s Guide Chapter 19 Policy Rule 151 19.3 V iewing and Editing Policy Configuration T o view a summary of the classifier configuration, scroll down to th e summar y table at the bottom of the Policy screen. T o change the settings of a rule, click a number in the Index field. Figure 65 Policy: Summary T able Diffserv Select No change t[...]

ES-3148 User’s Guide 152 Chapter 19 Policy Rule The following table describes the labels in this screen. 19.4 Policy Example The figure below shows an example Policy screen where you configure a policy to limit bandwidth and discard out-of-band traffic on a traffic flow classified using the Exam ple classifier (refer to Section 18.4 on page 145 )[...]

ES-3148 User’s Guide Chapter 19 Policy Rule 153 Figure 66 Policy Example[...]

ES-3148 User’s Guide 154 Chapter 19 Policy Rule[...]

ES-3148 User’s Guide Chapter 20 Q ueuing M ethod 155 C HAPTER 20 Queuing Method This chapter introduces th e queuing methods sup ported. 20.1 Queuing Method Overview Queuing is used to help solve performance degradation when there is network congestion. Use the Queuing Method screen to configure queuing algorith ms for outgoing traf fic. See also[...]

ES-3148 User’s Guide 156 Chapter 20 Que uing Method 20.1.3 We ighted Round Robin Scheduling (WRR) Round Robin Scheduling services queues on a rotati ng basis and is activated only when a port has more traffic than it can handle. A queue is a given an amount of bandwidth irrespective of the incoming traf fic on that port . This queue then moves to[...]

ES-3148 User’s Guide Chapter 20 Q ueuing M ethod 157 Figure 67 Queuing M ethod The following table describes the labels in this screen. Table 48 Queuing Me thod LABEL DESCRIPTION Method Select SPQ ( S tri ctly Priority Queuing), WFQ (Weighted Fair Scheduling) or WRR (Weighted Round Robin). S trictly Priori ty services queues based on priority onl[...]

ES-3148 User’s Guide 158 Chapter 20 Que uing Method * Settings in this row appl y to all ports. Use this row only if you want to make some settings the same for all ports. Use this row first to set the common settin gs and then make adjustments on a port-by-port basis. Note: Changes in this row are copied to all the ports as soon as you make them[...]

ES-3148 User’s Guide Chapter 21 VLAN Stacking 159 C HAPTER 21 VLAN S t acking This chapter shows you how to configure VLAN stacking on your switch. See the chapter on VLANs for more background informatio n on V irtual LAN 21.1 VLAN S t acking Overview A service provider can use VLAN stacking to allow it to distinguis h multiple customers VLANs, e[...]

ES-3148 User’s Guide 160 Chapter 21 VLAN Stacking Figure 68 VLAN S tacking Example 21.2 VLAN S t acking Port Roles Each port can have three VLAN stacking “roles”, Normal , Access Port and T unnel (the latter is for Gigabit ports only). • Select Normal for “regular” (non-VLAN stacking) IEEE 802.1Q frame switching. • Select Access Port [...]

ES-3148 User’s Guide Chapter 21 VLAN Stacking 161 Ty p e is a standard Ethernet type code identifyi ng the frame and indicates that whether the frame carries IEEE 802.1Q tag information. SP TPID (Service Provider T ag Protocol Identifier) is the service prov ider VLAN stacking tag type. Many vendors use 0x8100 or 0x9100. TPID (T ag Protocol Ident[...]

ES-3148 User’s Guide 162 Chapter 21 VLAN Stacking 21.4 Configuring VLAN S t acking Click Advanced App lications and then VLAN S tacking to display the screen as shown. Figure 69 VLAN S tacking The following table describes the labels in this screen. Table 52 VLAN Stacking LABEL DESCRIPTION Active Select this checkbox to enable VLAN stacking on th[...]

ES-3148 User’s Guide Chapter 21 VLAN Stacking 163 * Settings in this row apply to all ports. Use this row only if you want to make some settings the same for all ports. Use this row first to set the common settings and then make adjustments on a port-by-port basis. Note: Changes in th is row are copied to all the ports as soon as you make them. R[...]

ES-3148 User’s Guide 164 Chapter 21 VLAN Stacking[...]

ES-3148 User’s Guide Chapter 22 Multicast 165 C HAPTER 22 Multicast This chapter shows you how to conf igure various multicast features. 22.1 Multicast Overview T raditionally , IP packets are transmitted in one of either two ways - Unicast (1 sender to 1 recipient) or Broadcast (1 sender to everybod y on the network). Multicast delivers IP packe[...]

ES-3148 User’s Guide 166 Chapter 22 Multicast The switch forwards multicast traffic destined for multicast groups (that it has learned from IGMP snooping or that you have manually configured) to ports tha t are members of that group. IGMP snooping generates no additional ne twork traf fic, allowing you to significantly reduce multicast traffic pa[...]

ES-3148 User’s Guide Chapter 22 Multicast 167 Figure 71 Multicast Setting The following table describes the labels in this screen. Table 54 Multicast Setting LABEL DESCRIPTION IGMP Snooping Use these settings to configure IGMP Sno oping. Active Select Active to enable IGMP Snooping to forward group multicast traffic only to ports that are members[...]

ES-3148 User’s Guide 168 Chapter 22 Multicast Unknown Multicast F rame S pecify the action to perform when the switch receives an unknown multicast frame. Sel e ct Drop to discard the frame(s) . Select Floo ding to send the frame(s) to all ports. Reserved Multicast Group Multicast addresses (224.0.0.0 to 224.0 .0.255) are reserved for the local s[...]

ES-3148 User’s Guide Chapter 22 Multicast 169 22.4 IGMP Filtering Profile IGMP filter profiles allow you to control access to IGMP multicast groups. This allows you to have a service available to a specific IGMP multicast group. Y ou can configure an IGMP filter profile for an IGMP multicast group that has access to a service (like a SIP server f[...]

ES-3148 User’s Guide 170 Chapter 22 Multicast 22.5 MVR Overview Multicast VLAN Registration (MV R) is designed for applicatio ns (such as Media- on-Demand (MoD)) that use multicast traffi c across an Ethe rnet ring-based servic e provider network. MVR allows one single multicast VLAN to be shared among dif ferent subscriber VLANs on the network. [...]

ES-3148 User’s Guide Chapter 22 Multicast 171 22.5.2 MVR Modes Y ou can set your switch to operate in either dynamic or compatible mode. In dynamic mode, the switch sends IGMP leave and join reports to th e other multicast devices (such as multicast routers or servers) in the mu lticast VLAN. This allows the multicast devic es to update the multi[...]

ES-3148 User’s Guide 172 Chapter 22 Multicast Note: Y ou can create up to three multicast VLANs and up to 256 multicast rules on the switch. Y our switch automatically creates a static VLAN (with the same VID) when you create a multicast VLAN in this screen. Figure 75 MVR The following table describes the re lated labels in this screen. Table 56 [...]

ES-3148 User’s Guide Chapter 22 Multicast 173 22.7 MVR Group Configuration All source ports and receiver ports belonging to a multicast group can receive multicast data sent to this multicast group. Configure MVR IP multicast group address(es) in the Group Configuration screen. Click Group Configuration in the MVR screen. Mode S pecify the MVR mo[...]

ES-3148 User’s Guide 174 Chapter 22 Multicast Note: A port can belong to more than o ne multicast VLAN. However , IP multica st group addresses in dif ferent multicast VLANs cannot overlap. Figure 76 MVR: Group Configuratio n The following table describes the labels in this screen. Table 57 MVR: Group Configuratio n LABEL DESCRIPTION Multicast VL[...]

ES-3148 User’s Guide Chapter 22 Multicast 175 22.7.1 MVR Conf iguration Example The following figure shows a network example wh ere ports 1, 2 and 3 on the switch belong to VLAN 1. In addition, port 7 belo ngs to the multicast group with VID 200 to receive multicast traffic (the News and Movie channels) from the remote streaming media server , S [...]

ES-3148 User’s Guide 176 Chapter 22 Multicast Figure 78 MVR Configuration Example T o set the switch to forward the multicast group traffic to the su bscribers, configure multicast group settings in the Gr oup Configuration screen. The following fi gure shows an example where two multicast groups ( News and Movie ) are configured for the multicas[...]

ES-3148 User’s Guide Chapter 22 Multicast 177 Figure 79 MVR Group Configuration Exampl e Figure 80 MVR Group Configuration Exampl e[...]

ES-3148 User’s Guide 178 Chapter 22 Multicast[...]

ES-3148 User’s Guide Chapter 2 3 DHCP Relay 179 C HAPTER 23 DHCP Relay This chapter shows you how to set up DHCP relay . 23.1 DHCP Relay Overview DHCP (Dynamic Host Configuration Protocol , RFC 2131 and RFC 2132) allows indiv idual clients to obtain TCP/IP configuration at st art-up from a DHCP serve r . Y ou can co nfigure the switch to relay cl[...]

ES-3148 User’s Guide 180 Chapter 23 DHCP Relay Figure 81 DHCP Relay The following table describes the labels in this screen. Table 58 DHCP Relay LABEL DESCRIPTION Active Select this check box to enable DHCP relay . Remote DHCP Server 1 .. 3 Enter the IP address of a DHCP server in dotted decimal notation. Relay Agent Informatio n Select the Optio[...]

ES-3148 User’s Guide Chapter 24 Static Rout e 181 C HAPTER 24 S t atic Route This chapter shows you how to configure static routes. 24.1 Configuring S t atic Route Stat ic routes tell the switch how to forwar d IP traffic when you configure the TCP/IP parameters manually . Click IP Application , S tatic Routing in the navigation panel to di splay[...]

ES-3148 User’s Guide 182 Chapter 24 Static Route Destination IP Address This parameter specifies the IP network add ress of the final destination. Routing is always based on network nu mber . If you need to spec ify a route to a single host, use a subnet mask of 255.255.255.255 in the subn et mask field to force the network number to be identical[...]

ES-3148 User’s Guide Chapter 25 DiffSer v Code Point 183 C HAPTER 25 DiffServ Code Point This chapter shows you how to set up Dif fserv Code Point (DSCP) on each port and how to convert DSCP values to IEEE 802.1p values. 25.1 DiffServ Overview DiffServ Code Point (DSCP) is a field used for packe t classification on DiffServ networks. The higher t[...]

ES-3148 User’s Guide 184 Chapter 25 DiffServ Code Po int The following table describes the related labe ls you use to create a static route. 25.3 Configure DSCP Setting Use this screen to convert DSCP prio rity to IEEE 802.1p priority . Click IP Application , DiffServ , DSCP in the navigation panel to di splay the screen as shown. Figure 84 Dif f[...]

ES-3148 User’s Guide Chapter 25 DiffSer v Code Point 185 The following table describes the related labe ls you use to create a static route. Table 61 Static Routing LABEL DESCRIPTION Diffserv Click this to return to the main DiffServ screen. DSCP to 802.1p Mapping In this section you map each DSCP value with an 802.1p value in the drop down list [...]

ES-3148 User’s Guide 186 Chapter 25 DiffServ Code Po int[...]

ES-3148 User’s Guide Chapter 26 Maintenance 187 C HAPTER 26 Maintenance This chapter explains how to configure the ma intenance screens that let you maintain the firmware and configuration files. 26.1 The Maintenance Screen Click Management , Maintenance in the navigation panel to open the following scre en. Figure 85 Maintenance The following ta[...]

ES-3148 User’s Guide 188 Chapter 26 Maintenance 26.2 Load Factory Default s Follow the steps below to reset the sw itch back to the factory defaults. 1 In the Maintenance screen, click the Click Here button next to Load Factory Default to clear all switch configuration information yo u configured and return to the factory defaults. 2 Click OK to [...]

ES-3148 User’s Guide Chapter 26 Maintenance 189 Note: Note: Clicking the Apply or Add b utton does NOT save the changes permanently . All unsaved changes are erased af ter you reboot the switch. 26.4 Reboot System Reboot System allows you to restart the switch withou t physically turning the power of f. It also allows you to lo ad configuration o[...]

ES-3148 User’s Guide 190 Chapter 26 Maintenance Figure 88 Firmware Upg rade T ype the path and file name of the firmware f ile you wish to upload to the switch in the File Path text box or click Br owse to locate it. After you have specified the file, click Upgrade . After the firmware upgrade pr ocess is complete, see the System Info screen to v[...]

ES-3148 User’s Guide Chapter 26 Maintenance 191 Back up your current switch config uration to a computer using the Back up Configur ation screen. Figure 90 Backup Config uration Follow the steps below to back up the current switch configuration to your computer in this screen. 1 Click Backup . 2 Click Save to display the Save As screen. 3 Choose [...]

ES-3148 User’s Guide 192 Chapter 26 Maintenance 26.8.1.1 Example FTP Commands ftp> put firmware.bin ras This is a sample FTP session showing the transfer of the computer file "firmware.bin" to the switch. ftp> get config config.cfg This is a sample FTP session saving the current configuration to a file called “config.cfg” on y[...]

ES-3148 User’s Guide Chapter 26 Maintenance 193 26.8.3 GUI-based FTP Clients The following table describes some of the commands that you may see in GUI-based FTP clients. 26.8.4 FTP Restrictions FTP will not work when: • FTP service is disabled in the Service Access Control screen. • The IP address(es) in the Remote Management screen does n o[...]

ES-3148 User’s Guide 194 Chapter 26 Maintenance[...]

ES-3148 User’s Guide Chapter 27 Access Control 195 C HAPTER 27 Access Control This chapter describes how to control access to the switch. 27.1 Access Control Overview A console port and FTP are allowed one session each, T elnet and SSH sh are four sessions, up to five W eb sessions (five di fferent usernames and passwords ) and/or limitless SNMP [...]

ES-3148 User’s Guide 196 Chapter 27 Access Control 27.3 About SNMP Simple Network Management Protocol (SNMP) is an application lay e r protocol used to manage and monitor TCP/IP-based devices. SNMP is used to exchange management information between th e network manag ement system (NMS) and a network element (NE). A manager station can m anage and[...]

ES-3148 User’s Guide Chapter 27 Access Control 197 27.3.1 Supported MIBs MIBs let administrators collect statisti c s and monitor status and performance. The switch supports the following MIBs: • SNMP MIB II (RFC 1213) • RFC 1 157 SNMP v1 • RFC 1493 Bridge MIBs • RFC 1643 Ethernet MIBs • RFC 1 155 SMI • RFC 2674 SNMPv2, SNMPv2c • RF[...]

ES-3148 User’s Guide 198 Chapter 27 Access Control 27.3.3 Configuring SNMP From the Access Control screen, display the SNMP screen. Y ou can click Access Contr ol to go back to the Access C ontrol screen. Figure 93 Access Control: SNMP The following table describes the labels in this screen. 27.3.4 Setting Up Login Account s Up to five people (on[...]

ES-3148 User’s Guide Chapter 27 Access Control 199 • A non-administrator (usernam e is something other than admin ) is someone who can view but not configure switch settings. Click Access Control from the navigation panel and then click Logins from this screen. Figure 94 Access Control: Logins The following table describes the labels in this sc[...]

ES-3148 User’s Guide 200 Chapter 27 Access Control 27.4 SSH Overview Unlike T elnet or FTP , which transmit data in clear text, SSH (Secure Shell) is a secure communication protoc ol that combines authenticatio n and data encryption to provide secure encrypted communication between two hosts over an unsecured network. Figure 95 SSH Communication [...]

ES-3148 User’s Guide Chapter 27 Access Control 201 Figure 96 How SSH W orks 1 Host Identification The SSH client s ends a conn ection request to the SSH server . The server identifies itself with a host key . The client encrypts a rand omly generated session key with the host key and server key and sends the result back to the server . The client[...]

ES-3148 User’s Guide 202 Chapter 27 Access Control 27.6.1 Requirement s for Using SSH Y ou must install an SSH client pr ogram on a client computer (W indows or Linux operati ng system) that is used to co nnect to the switch over SSH. 27.7 Introduction to HTTPS HTTPS (HyperT ext Transfer Protocol over Secure Socket Layer , or HTTP over SSL) is a [...]

ES-3148 User’s Guide Chapter 27 Access Control 203 27.8 HTTPS Example If you haven’t changed the default HTTPS port on the switch, then in your browser enter “https://switch IP Address/” as the web site address where “switch IP Address” is the IP address or domain name of the switch you wish to access. 27.8.1 Internet Explorer W arning [...]

ES-3148 User’s Guide 204 Chapter 27 Access Control Figure 99 Security Certificate 1 (Net scape) Figure 100 Security Certificate 2 (Net scape) 27.8.3 The Main Screen After you accept the certificat e an d enter the login username and password, the switch main screen appears. A lock displayed in the bottom ri ght of the browser status bar denote s [...]

ES-3148 User’s Guide Chapter 27 Access Control 205 Figure 101 Example: Lock Denotin g a Secure Connectio n 27.9 Service Port Access Control Service Access Control allows you to decide what services you may use to access the switch. Y ou may also change the default service port an d config ure “trusted co mputer(s)” for each service in the Rem[...]

ES-3148 User’s Guide 206 Chapter 27 Access Control Figure 102 Access Control: Service Access Control The following table describes th e fields in this screen. 27.10 Remote Management From the Access Control screen, display the Remote Management screen as shown next. Y ou can specify a group of one or more “trust ed computers” from which an ad[...]

ES-3148 User’s Guide Chapter 27 Access Control 207 Figure 103 Access Control: Remote Management The following table describes the labels in this screen. Table 71 Access Control: Remote Management LABEL DESCRIPTION Entry This is the client set index number . A “client set” is a group of one or more “trusted computers” from which an adminis[...]

ES-3148 User’s Guide 208 Chapter 27 Access Control[...]

ES-3148 User’s Guide Chapter 28 Diagnostic 209 C HAPTER 28 Diagnostic This chapter explains the Diagnostic screen. 28.1 Diagnostic Click Management , Diagnostic in the navi gation pane l to open th is screen. Use this screen to check system logs, ping IP addresses or perform port tests. Figure 104 Diagnostic The following table describes the labe[...]

ES-3148 User’s Guide 210 Chapter 28 Diagnostic[...]

ES-3148 User’s Guide Chapter 29 Syslog 211 C HAPTER 29 Syslog This chapter explains the syslog screens. 29.1 Syslog Overview The syslog protocol allows devices to send event notification messages across an IP network to syslog servers that collect the event mes sages. A syslog-enabled device can generate a syslog message and send it to a syslog s[...]

ES-3148 User’s Guide 212 Chapter 29 Syslog Figure 105 Syslog The following table describes the labels in this screen. 29.3 Syslog Server Setup Click Management and then Syslog in the navigation pa nel to display the Syslog Setup screen. Click the Syslog Server Setup link to open the following screen. Use this screen to configure a list of externa[...]

ES-3148 User’s Guide Chapter 29 Syslog 213 Figure 106 Syslog: Server Se tup The following table describes the labels in this screen. Table 75 Syslog: Server Setup LABEL DESCRIPTION Active Select this check box to have the device send logs to this syslog server. Clear the check box if you want to create a syslog se rver entry but not hav e the dev[...]

ES-3148 User’s Guide 214 Chapter 29 Syslog[...]

ES-3148 User’s Guide Chapter 30 Clu ster Mana gement 215 C HAPTER 30 Cluster Management This chapter introduces cluster management. 30.1 Cluster Management S t atus Overview Cluster Managemen t allows you to manage s witches through one switch, ca lled the cluster manager . The switches must be directly connec ted and be in the same VLAN group so[...]

ES-3148 User’s Guide 216 Chapter 3 0 Cluster Management Figure 107 Clustering Application Example 30.2 Cluster Management S t atus Click Management , Cluster Management in the navigation panel to display the following screen. Note: A cluster can only have one manager .[...]

ES-3148 User’s Guide Chapter 30 Clu ster Mana gement 217 Figure 108 Cluster Management: S tatu s The following table describes the labels in this screen. 30.2.1 Cluster Member Switch Management Go to the Clustering Management S tatus screen of the cluster manager switch and then select an Index hyperlink from the list of members to go to that clu[...]

ES-3148 User’s Guide 218 Chapter 3 0 Cluster Management Figure 109 Cluster Managem ent: Cluster Member W eb Configurator Screen 30.2.1.1 Uploading Firmware to a Cluster Member Switch Y ou can use FTP to upload firmwa re to a cluster member switch through the cluster manager switch as shown in the following example.[...]

ES-3148 User’s Guide Chapter 30 Clu ster Mana gement 219 Figure 1 10 Example: Uploading Firmwar e to a Cluster Member Switch The following table explains some of the FTP parameters. 30.3 Clustering Management Configuration Use this screen to configure clustering management. Click Configuration from the Cluster Management screen to display the nex[...]

ES-3148 User’s Guide 220 Chapter 3 0 Cluster Management Figure 1 1 1 Clustering Management Configu ration The following table describes the labels in this screen. Table 79 Clustering Mana gement Configuration LABEL DESCRIPTION Clustering Manager Active Select Active to have this switch become the cluster manager switch. A cluster can only have on[...]

ES-3148 User’s Guide Chapter 30 Clu ster Mana gement 221 Apply Click Apply to save your changes to the switch’s run-time memory . The switch loses these chang es if it is turned off or loses power , so use the Save link on the top navigation panel to save your chang es to the non-volatile memory wh en you are done configuring. Cancel Click Canc[...]

ES-3148 User’s Guide 222 Chapter 3 0 Cluster Management[...]

ES-3148 User’s Guide Chapter 31 MAC Table 223 C HAPTER 31 MAC T able This chapter introduces the MAC T able scre en. 31.1 MAC T able Overview The MAC T able screen (a MAC table is also known as a filtering database) shows how frames are forwarded or filtered across the switch’ s ports. It shows what device MAC address, belonging to what VLAN gr[...]

ES-3148 User’s Guide 224 Chapter 31 MAC Table 31.2 V iewing the MAC T able Click Management , MAC T able in the navigation panel to di splay the following screen. Figure 1 13 MAC T able The following table describes the labels in this screen. Table 80 MAC Table LABEL DESCRIPTION Sort by Click one of the followi ng buttons to di splay and arrang e[...]

ES-3148 User’s Guide Chapter 32 ARP Table 225 C HAPTER 32 ARP T able This chapter introduces ARP T able. 32.1 ARP T able Overview Address Resolution Protocol (ARP) is a prot ocol for mapping an Internet Protocol address (IP address) to a physical machine address, al so known as a Media Access Control or MAC address, on the local area network. An [...]

ES-3148 User’s Guide 226 Chapter 32 ARP Table Figure 1 14 ARP T able The following table describes the labels in this screen. Table 81 ARP Table LABEL DESCRIPTION Index This is the ARP T a ble entry number . IP Address This is the learned IP address of a device connecte d to a switch port with corresponding MAC address below . MAC Address This is[...]

ES-3148 User’s Guide Chapter 33 Config ure Clone 227 C HAPTER 33 Configure Clone This chapter shows you how you can copy the settings of one port onto other ports. 33.1 Configure Clone Cloning allows you to co py the basic and advanced settings fro m a sour ce port to a destination port or ports. Click Management , Configure Clon e to open the fo[...]

ES-3148 User’s Guide 228 Chapter 33 Configure Clone The following table describes the labels in this screen. Table 82 Configure Clone LABEL DESCRIPTION Source/ Destination Port Enter the source port under the So urce label. This port’ s attributes are copied. Enter the destination port or ports under the Destination label. Th ese are the ports [...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 229 C HAPTER 34 Introducing Commands This chapter introduces commands and gives a summary of commands available. 34.1 Overview In addition to the web con figurator , you can use commands to configure the switch. Use commands for advanced switch diagnosis and troubleshooting. If you ha ve prob[...]

ES-3148 User’s Guide 230 Chapter 34 Introducing Commands 34.2.1.1 Initial Screen When you turn on your switch, it performs several internal tests as well as line initialization. Y ou can view the initialization in formation using the console port . After the initialization, the login screen displays (refer to Section 34.3 on page 230 ). Use the f[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 231 • The optional fields in a command are enclosed in square brackets [], for instance, configure snmp-server [contact <syst em contact>] [location <system location>] means that the contact and location fields are optional. • “Command” refers to a co mmand used in the com[...]

ES-3148 User’s Guide 232 Chapter 34 Introducing Commands Use the following commands to specify privilege levels for login accounts. Syntax: logins username <username> password <password> logins username <username> privilege <0-14> where 34.7 Command Modes There are three command modes: User , Enable and Configur e . The mo[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 233 The following table describ es command interpreter mode s and how to access them. Enter exit to quit from the current mo de or enter logout to exit the comm and interpreter . 34.8 Getting Help The system includes a help faci lity to provi de you with the following information about the co[...]

ES-3148 User’s Guide 234 Chapter 34 Introducing Commands • List of available commands under a command group. • Detailed descriptions of the commands. 34.8.1 List of A vailable Commands Enter “ help ” to displa y a list of a vailable co mma nds and the corresponding su b commands. sysname> help Commands available: help logout exit histo[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 235 Enter “ ? ” to display a list of comman d s you can use. Enter <command> help to display detaile d sub commands and para meters. Enter <command> ? to display detailed help inform ation about the sub commands and parameters. sysname# ? baudrate Change baud rate boot Perfor [...]

ES-3148 User’s Guide 236 Chapter 34 Introducing Commands 34.9 Using Command History The switch keeps a list of recently used commands availa ble to you for reuse. Y ou can use any commands in the history agai n by pressing the up ( y ) or down ( z ) arrow key to scroll through the previously used commands and press [ENTER] . Use the history comma[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 237 34.10.2 Logging Out In User or Enable mode, enter the exit or logout command to log out of the CLI. In Co nfig mode entering exit takes you out of the Config mode and into Enable mo de and entering logout logs you out of the CLI. 34.1 1 Command Summary The following sections summarize the[...]

ES-3148 User’s Guide 238 Chapter 34 Introducing Commands 34.1 1.2 Enable Mo de The following table describes the co mmands available for Enable mode. help Displays command help information. 0 ssh <1|2> <[user@]dest- ip> Connects to an SSH server with the specified SSH version. 0 Table 84 Command Summary: Use r Mode (continued) COMMAND[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 239 port-isolation Displays port isolation settings. 13 spanning-tree config Di splays S panning Tree Protocol (STP) settings. 13 mrstp <treeIndex> Displays the STP settings for the specific tree. 13 mac address-ta ble <all [mac|vid|port]> Displays MAC address table. Y ou can sort[...]

ES-3148 User’s Guide 240 Chapter 34 Introducing Commands bandwidth- control Displays bandwidth control settings on th e port(s). 13 egress Displays outgoin g port information on the port(s). 13 bstorm-control Displays broadcast storm control settings on th e port(s). 13 igmp-immediate- leave Displays IGMP immediate leave settings on th e port(s).[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 241 session Displays current HTTPS session(s). 13 certificate Displays the HTTPS certificates. 13 key <rsa|dsa> Displays the HTTPS key . 13 timeout Displays the HT TPS session timeout. 13 multi-login Displays multi-login information 13 plt Displays Packet Loop T est (PL T). 13 mac-aging[...]

ES-3148 User’s Guide 242 Chapter 34 Introducing Commands baudrate <1|2|3|4|5> Changes the co nsole port speed. Choices are 1 (9600), 2 (19200), 3(38400), 4 (57600 ) and 5 (1 15200). 13 boot config <index> Restarts the system with the specified configuration fil e. 13 reload config <index> Restarts the system and use the specifie[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 243 34.1 1.3 General Configuration Mode The following table lists the commands in Configuration (or Config) mode. help Displays command help informat ion. 13 ssh <1|2> <[user@]dest-ip> Connects to an SSH server with the specified SSH version. 13 [command </>] Connects to an [...]

ES-3148 User’s Guide 244 Chapter 34 Introducing Commands mac-forward mac <mac-addr> vlan <vlan-id> interface <interface-id> Removes the specified MAC forwarding entry , belonging to a VLAN group (if any) forwarded through an interface(s). 13 mac <mac-addr> vlan <vlan-id> interface <interface-id> inactive Enable[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 245 port-access- authenticator Disables port authentication on the switch. 13 <port-list> Disables authentication on the listed ports. 13 <port-list> reauthenticate Disables the re-authenticati on mechanism on the listed port(s). 13 port-security Disables port security on the swit[...]

ES-3148 User’s Guide 246 Chapter 34 Introducing Commands policy <name> Deletes the po licy . A policy sets actions for classifier traffic. 13 <name> inactive Enables a policy . 13 vlan <vlan-id> Deletes the static VLAN entry . 13 dhcp-relay Disables DHCP relay . 13 option Disables the relay agent information option 82. 13 inform[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 247 vlan <1-4094> Enters the VLAN configuration mode. See Section 34.1 1.5 on page 259 for more information. 13 vlan-type <802.1q|port- based> S pecifies the VLAN type. 13 igmp- snooping Enables IGMP snooping. 13 host-timeout <1-16711450> Sets the host timeout va lue. 13 lea[...]

ES-3148 User’s Guide 248 Chapter 34 Introducing Commands name-server <ip> Sets the IP address of a domain name server . 13 address default- gateway <ip> Sets the default gateway's IP address for the out-of-band management port. 13 address <ip> <mask> Sets the IP address and subnet mask of the out-of-band management po[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 249 member <mac- address> password <password-str> Sets the cluster member switch's hardware MAC address and passw ord. 13 rcommand <mac- address> Logs into a clu ster member switch. 13 classifier <name> <[ packet-format <802.3untag|802. 3tag|EtherIIunta g|Et[...]

ES-3148 User’s Guide 250 Chapter 34 Introducing Commands policy <name> classifier <classifier- list> < [ vlan<vlan-id> ] [ egress-port <port-num> ] [ priority <0-7> ] [ dscp <0- 63>] [ tos <0-7> ] [ bandwidth <bandwidth> ] [ outgoing- packet-format <tagged|untagged > ] [ out- of-profile-dsc[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 251 timeout <1-1000> Specifies the RADIUS server timeout value. 13 mode <priority|roun d-robin> S pecifies the mode for RADIUS server selection. 13 port- access- authentica tor Enables 802.1x authentication o n the switch. 13 <port-list> Enables 802.1x authentication o n the[...]

ES-3148 User’s Guide 252 Chapter 34 Introducing Commands hello-time <1- 10> maximum-age <6-40> forward- delay <4-30> Sets Hello T ime, Maximum Age and Forward Delay . 13 <port-list> Enables STP on a specified port. 13 <port-list> path-cost <1- 65535> Sets the STP p ath cost for a specified port. 13 <port-lis[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 253 storm- control Enables broadcast storm control on the switch. 13 bandwidth- control Enables bandwidth control. 13 mac-aging- time <10-3000> Sets learned MAC aging time. 13 snmp- server get-community <property> Sets the get community . 13 set-community <property> Sets the[...]

ES-3148 User’s Guide 254 Chapter 34 Introducing Commands <index> start- addr <ip> end- addr <ip> service <[telnet] [ftp] [http] [icmp] [snmp] [ssh] [https]> S pecifies a group of trusted computer(s) from which an administrator may use a service to manage the switch. 13 admin- password <pw-string> <confirm-string&g[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 255 34.1 1.4 interface port-channel Commands The following table lists the interface port-channel commands in configuration mode. Use these commands to configure the ports. option Allows the switch to add DHCP relay agent information. 13 information Allows the switch to add system name to age[...]

ES-3148 User’s Guide 256 Chapter 34 Introducing Commands igmp-querier- mode <auto|fixed|edg e> Sets the IGMP querier mode of a port. Selects auto to treat the IGMP queries normally , fixed to always treat the port as a querier port no matter there i s a query or edge to treat the port as a non- querier p ort which dr ops any IGMP queries re[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 257 egress Enables bandwidth limits allowed for outgoing traffic on the port(s). 13 egress <Kbps> Sets the maximum bandwidth allowed for outgoing traffic on the port(s). 13 broadcast-limit Enables broadcast storm con trol limit on the switch. 13 <pkt/s> Sets how many broadcast pac[...]

ES-3148 User’s Guide 258 Chapter 34 Introducing Commands igmp-filtering profile Disables IGMP filte ring on the port. 13 igmp-group- limited Disables IGMP group l imitation. 13 ingress-check Disables ingress checking o n the port(s). 13 gvrp Disable GVRP on the port(s). 13 flow-control Disables flow control on the port(s). 13 vlan-trunking Disabl[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 259 34.1 1.5 config-vlan Commands The following table lists the vlan commands in configuration mode. protocol-based- vlan name <name> ethernet-type <ethernet-type> vlan <vid> priority <0-7> Creates a protocol based VLAN with the specified parameters. 13 inactive Disabl[...]

ES-3148 User’s Guide 260 Chapter 34 Introducing Commands 34.1 1.6 mvr Comm ands The following table lists the mvr commands in configuration mode. ip address inband-default dhcp-bootp Sets the default in-band interface to use a sta tic IP address in this VLAN. The switch will use the default IP address of 0.0.0.0 if you do not configure a static I[...]

ES-3148 User’s Guide Chapter 34 Intro ducing Comma nds 261 receiver-port <port-list> Sets the receiver port(s). An MVR receiver port ca n only receive mult icast traffic i n a multicast VLAN. 13 inactive Disables MVR settings. 13 mode <dynamic|compati ble> Sets th e MVR mode ( dynamic or compatible ). 13 name <name-str> Sets the[...]

ES-3148 User’s Guide 262 Chapter 34 Introducing Commands[...]

ES-3148 User’s Guide Chapter 35 User and Enable Mode Commands 263 C HAPTER 35 User and Enable Mode Commands This chapter describes some commands which yo u can perform in the User and Ena ble modes. 35.1 Overview The following command examples show how you can use User and Enab le mode s to diagnose and manage you r switch. 35.2 show Commands The[...]

ES-3148 User’s Guide 264 Chapter 35 User and En able Mode Commands 35.2.2 show ip Syntax: show ip This command displays the IP re lated information (such as IP address and subnet mask) on all switch interfaces. The following figure shows th e default interface settings. 35.2.3 show logging Syntax: show logging This command displays the system log[...]

ES-3148 User’s Guide Chapter 35 User and Enable Mode Commands 265 This command displays statistics of a port. The following ex ample shows that po rt 2 is up and the related information. 35.2.5 show mac address-table Syntax: show mac address-table <all <sort>|s tatic> Where <sort> = Specifies the sorting criteria (MAC, VID or po[...]

ES-3148 User’s Guide 266 Chapter 35 User and En able Mode Commands This command displays the MAC address(es) st ored in the switch. The following example shows the static MAC address table. 35.3 ping Syntax: ping <ip|host-name> < [in-band|out-o f-band|vlan <vlan-id> ] [ size <0-1472> ] [ -t ]> where This command sends Ping[...]

ES-3148 User’s Guide Chapter 35 User and Enable Mode Commands 267 where This command displays information about the route to an Ethernet device. The following example displays route information to an Ethernet device with an IP address of 192.168.1.100 . 35.5 Copy Port Attributes Use the copy running-config command to copy attributes of one port t[...]

ES-3148 User’s Guide 268 Chapter 35 User and En able Mode Commands where An example is shown next. • Copy all att ributes of port 1 to port 2 • Copy selected attributes (active, ba ndwidth limit and STP settings) to ports 5-8 35.6 Configuration File Maintenance The following sections shows how to manage the configuration files. 35.6.1 Using a[...]

ES-3148 User’s Guide Chapter 35 User and Enable Mode Commands 269 Note: When you use the write memory command without specifying a configuration file index number , the switch saves the changes t o the configuration file the switch is currently usin g. 35.6.2 Resetting to the Factory Default Follow the steps below to reset the sw itch back to the[...]

ES-3148 User’s Guide 270 Chapter 35 User and En able Mode Commands[...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 271 C HAPTER 36 Configuration Mode Commands This chapter describes how to enable and config ure your switc h’ s feat ures using commands. For more background information, see the f eature specific chapters which proceed the commands chapters. 36.1 Enabling IGMP Snooping T o enable I[...]

ES-3148 User’s Guide 272 Chapter 36 Config uration Mod e Commands • Enable IGMP snooping on the switch. • Set the host-timeout and leave-timeout values to 30 seconds • Set the switch to drop packet s from unknown multicast groups. 36.2 Configure IGMP Filter Use the following commands in the config mo de to configure IGMP filtering profiles.[...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 273 36.3 Enabling STP Use the spanning-tree or the mrstp commands to enable and configure STP on the switch. The dif ference between the com mands is that spanning-tree only all ows you to set up one spanning tree configuratio n and the mrstp command allows you to set up multiple ones[...]

ES-3148 User’s Guide 274 Chapter 36 Config uration Mod e Commands An exampl e using spanning-tree command is shown next. • Enable STP on the switch. • Set the bridge priority of the switch to 0. • Set the Hello T ime to 4, Maximum Age to 20 and Forward Delay to 15 on the switch. • Enable STP on port 5 with a path cost of 150. • Set the [...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 275 36.4 no Command Examples These are the commonly used comm and examples that belong to the no group of commands. The no group commands are commands which are preceded by keyword no . This command negates the intended ac tion of the command. In most case s the no command disables, r[...]

ES-3148 User’s Guide 276 Chapter 36 Config uration Mod e Commands where An example is shown next. • Enable the IP route with the IP addres s of 192.168.1 1.1 and subn et mask of 255.255.255.0. This ip route must have alr eady been created and made inactive prior to re-enable command being applied. 36.4.4 Other Examples of no Commands In some ca[...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 277 36.4.4.2 no port-access-authenticator Syntax: no port-access-authenticator no port-access-authenticator <port-l ist> reauthenticate no port-access-authenticator <port-l ist> where An example is shown next. • Disable authentication on the switch. • Disable re-authen[...]

ES-3148 User’s Guide 278 Chapter 36 Config uration Mod e Commands • Disable the secure shell RSA1 encryption key . • Remove the remote host with IP ad dress 172.165.1.8 from the list of known hosts. • Remove the remote host with IP address 172.165.1.9 and with an SSH-RSA encryption key from the list of kn own hosts. 36.5 Queuing Method Comm[...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 279 Syntax: ip route <ip> <mask> <next-hop-ip> ip route <ip> <mask> <next-hop-ip> [ metric <metric>][name <name>] [inactive] where An example is shown next. • Create a static route with the destination IP address of 172.21.1.104, subne[...]

ES-3148 User’s Guide 280 Chapter 36 Config uration Mod e Commands where An example is shown next. • Create a filtering rule cal led “filter1”. • Drop packets coming from and going to MAC address 00:12 :00:12:00:12 on VLAN. 36.8 Enabling T runking T o create and e nable a trunk, enter trunk followed by the ports which you want to group and[...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 281 • Create trunk 1 on the switch. • Place ports 5-8 in trunk 1. • Enable dynamic l ink aggregation (LACP) on trunk 1. 36.9 Enabling Port Authentication T o enable a port authentication, you need to specify yo ur RADIUS server details and select the ports which require external[...]

ES-3148 User’s Guide 282 Chapter 36 Config uration Mod e Commands See Section 36.9.2 on page 2 82 for an example. 36.9.2 Port Authentication Settings Use the port-access-authenticator command to configure port security on the switch. Syntax: port-access-authenticator port-access-authenticator <port-list > port-access-authenticator <port-[...]

ES-3148 User’s Guide Chapter 36 C onfigurat ion Mode Com mands 283 An example is shown next. • Specify RADIUS server 1 with IP address 10.10.10.1, port 1890 a nd the string secretKey as the password. See Section 36.9.1 on page 281 for more information on RADIUS server commands. • Specify the timeout period of 30 seconds that the switch w ill [...]

ES-3148 User’s Guide 284 Chapter 36 Config uration Mod e Commands[...]

ES-3148 User’s Guide Chapter 37 Interfa ce Commands 285 C HAPTER 37 Interface Commands These are some commonly used configur ation commands that belong to the interface group of commands . 37.1 Overview The interface commands allow you to configur e the switch on a port by port basis. 37.2 Interface Command Examples This section provides examples[...]

ES-3148 User’s Guide 286 Chapter 37 Inte rface Comm ands where An example is shown next. • Enable ports 1, 3, 4 and 5 for configuration. • Set the BPDU control to tunnel , to forward BPDUs received on ports one, three, four and five. 37.2.3 broadcast-limit Syntax: broadcast-limit broadcast-limit <pkt/s> where An example is shown next. ?[...]

ES-3148 User’s Guide Chapter 37 Interfa ce Commands 287 Syntax: bandwidth-limit bandwidth-limit pir <Kbps> bandwidth-limit cir <Kbps> bandwidth-limit egress <Kbps> where An example is shown next. • Enable port one for config uration. • Enable bandwidth contro l. • Set the outgoing traffic bandwidt h limit to 5000Kbps. • [...]

ES-3148 User’s Guide 288 Chapter 37 Inte rface Comm ands • Enable port mirroring. • Enable the monitor port 3. • Enable ports 1, 4, 5 and 6 for configuration. • Enable port mirroring on the ports. • Enable port mirroring for outgoi ng traffic. T raffic is copied from ports 1, 4, 5 and 6 to port three in order to examine it in more detai[...]

ES-3148 User’s Guide Chapter 37 Interfa ce Commands 289 • Enable ingress checking on the interface. 37.2.8 frame-type Syntax: frame-type <all|tagged|untagged> where An example is shown next. • Enable ports one, three, four an d five for configuration. • Enable ingress checking on the ports. • Enable tagged frame-types on the interfa[...]

ES-3148 User’s Guide 290 Chapter 37 Inte rface Comm ands • Set the queue weights from Q0 to Q7. 37.2.10 egress set Syntax: egress set <port-list> where An example is shown next. • Enable port-based VLAN tagging on the switch. • Enable ports one, three, four an d five for configuration. • Set the outgoing traffic ports as the CPU (0)[...]

ES-3148 User’s Guide Chapter 37 Interfa ce Commands 291 37.2.12 name Syntax: name <port-name-string> where An example is shown next. • Enable ports one, three, four an d five for configuration. • Set a name for the ports. 37.2.13 speed-duplex Syntax: speed-duplex <auto|10-half|10-full|1 00-half|100-full|1000-full> where An example[...]

ES-3148 User’s Guide 292 Chapter 37 Inte rface Comm ands An example is shown next. • Select ports 3-6 for internal loopback test. • Execute the test command. • V iew the results. 37.3 Interface no Command Examples Similar to the no commands in the Enable and Config mode s, the no commands for the Interface sub mode also disable certain feat[...]

ES-3148 User’s Guide Chapter 38 IEEE 802.1Q Tagg ed VLAN Commands 293 C HAPTER 38 IEEE 802.1Q T agged VLAN Commands This chapter describes the IEEE 802.1Q T agged VLAN and associated commands. 38.1 Configuring T agged VLAN The following procedur e shows you how to configure tagg ed VLAN. 1 Use the IEEE 802.1Q tagged VLAN comman ds to configure ta[...]

ES-3148 User’s Guide 294 Chapter 38 IEEE 802.1Q Tagged VLAN Commands 38.2 Global VLAN1Q T agged VLAN Configuration Commands This section shows you how to configure and monitor the IEEE 802.1Q T agged VLAN. 38.2.1 GARP St atus Syntax: show garp This command shows the switch’ s GARP timer se ttings, including the join, leave and leave all timers.[...]

ES-3148 User’s Guide Chapter 38 IEEE 802.1Q Tagg ed VLAN Commands 295 Switches join VLANs by making a declaration. A declaration is made by issuing a Join message using GARP . Declarations are withdraw n by issuing a Leave message. A Leave All message terminates all registrations. GARP timers set declaration timeout values. The following example [...]

ES-3148 User’s Guide 296 Chapter 38 IEEE 802.1Q Tagged VLAN Commands 38.3.1 Set Port VID Syntax: pvid <VID> where This command sets the default VLAN ID on the port(s). The following ex ample sets the default VID to 200 on ports 1 to 5. 38.3.2 Set Accept able Frame T ype Syntax: frame-type <all|tagged|untagged> where This command sets [...]

ES-3148 User’s Guide Chapter 38 IEEE 802.1Q Tagg ed VLAN Commands 297 38.3.4 Modify St atic VLAN Use the following commands in the config-vla n mode to configure the static VLAN table. Syntax: vlan <vlan-id> fixed <port-list> forbidden <port-list> name <name-str> normal <port-list> untagged <port-list> no fixed[...]

ES-3148 User’s Guide 298 Chapter 38 IEEE 802.1Q Tagged VLAN Commands 3 The switch notes what the SVLAN table say s (that is, the SVLAN tells the switch whether or not to forward a frame and if the forwarde d frames shoul d have tags). 4 Then the switch applies the port filter to finish the forwar ding decision. This means that frames may be d rop[...]

ES-3148 User’s Guide Chapter 38 IEEE 802.1Q Tagg ed VLAN Commands 299 38.5 Disable VLAN Syntax: vlan <vlan-id> inactive This command disables the specified VLAN ID in the SVLAN (S tatic VLAN) table. 38.6 Show VLAN Setting Syntax: show vlan This command shows the IEEE 802.1Q T agged SVLAN (Static VLAN) table. An example is shown next. • VI[...]

ES-3148 User’s Guide 300 Chapter 38 IEEE 802.1Q Tagged VLAN Commands[...]

ES-3148 User’s Guide Chapter 39 Multicast VLAN Registration Commands 301 C HAPTER 39 Multicast VLAN Registration Commands This chapter shows you how to use Mu lticast VLAN Registration (mvr) commands. 39.1 Overview Use the mvr commands in the co nfiguration mode to create and configure multicast VLANs. Note: If you want to enable IGMP snooping se[...]

ES-3148 User’s Guide 302 C hapter 39 Multic ast VLAN Registratio n Commands • Enter MVR mode. Create a multicast VLAN with the name multiVlan and the VLAN ID of 3. • Specify source ports 2, 3, and 5 and receiver ports 6-8. • Specify dynamic mode for the multicast group. • Configure MVR multicast group addresses by the name of ipgroup . ?[...]

ES-3148 User’s Guide Chapter 40 Troubleshooting 303 C HAPTER 40 T roubleshooting This chapter covers potential problems and possible remedies. 40.1 Problems St arting Up the Switch 40.2 Problems Accessing the Switch Table 90 Troubleshootin g the Start-Up of Your Switch PROBLEM CORRECTIVE ACTION None of the LEDs turn on when you turn on the switch[...]

ES-3148 User’s Guide 304 Chapter 40 Troublesh ooting 40.2.1 Pop-up Windows, Ja vaScript s and Java Permissions In order to use the web configurator you need to allow: • W eb browser pop-up windows fro m your device. • JavaScripts (enabled by default). • Java permissions (enabled by default). Note: Internet Explorer 6 screens are used here. [...]

ES-3148 User’s Guide Chapter 40 Troubleshooting 305 Figure 1 18 Internet Options 3 Click Apply to save this setting. 40.2.1.1.2 Enable pop-up Blockers with Exceptions Alternatively , if you only want to allow pop-up windows from your device, see the follo wing steps. 1 In Internet Explorer , select To o l s , Internet Options and then the Privacy[...]

ES-3148 User’s Guide 306 Chapter 40 Troublesh ooting Figure 1 19 Internet Options 3 T ype the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.1.1. 4 Click Add to move the IP address to the list of Allowed sites .[...]

ES-3148 User’s Guide Chapter 40 Troubleshooting 307 Figure 120 Pop-up Blocker Settings 5 Click Close to return to the Privacy screen. 6 Click Apply to save this setting. 40.2.1.2 JavaScript s If pages of the web configura tor do not display properly in Internet Explorer , check that JavaScripts are allowed. 1 In Internet Explorer , click T ools ,[...]

ES-3148 User’s Guide 308 Chapter 40 Troublesh ooting Figure 121 Internet Options 2 Click the Custom Level... button. 3 Scroll down to Scripting . 4 Under Active scripting make sure that Enable is selected (the default). 5 Under Scripting of Java applets make sure that Enable is sele cted (the default). 6 Click OK to clos e the window .[...]

ES-3148 User’s Guide Chapter 40 Troubleshooting 309 Figure 122 Security Settings - Java Scripting 40.2.1.3 Java Permissions 1 From Internet Explorer , click To o l s , Internet Options and then the Security tab. 2 Click the Custom Level... button. 3 Scroll down to Microsoft VM . 4 Under Java permissions ma ke sure that a safety level is selected.[...]

ES-3148 User’s Guide 310 Chapter 40 Troublesh ooting Figure 123 Security Settings - Java 40.2.1.3.1 JA V A (Sun) 1 From Internet Explorer , click To o l s , Internet Options and then the Advanced tab. 2 make sure that Use Java 2 for <applet> u nder Java (Sun) is selected. 3 Click OK to clos e the window .[...]

ES-3148 User’s Guide Chapter 40 Troubleshooting 311 Figure 124 Java (Sun) 40.3 Problems with the Password Table 92 Troubleshootin g the Password PROBLEM CORRECTIVE ACTION Cannot access the switch. The password field is case se nsitive. Make sure that you enter the correct password using the proper casing. The administrator username is “admin”[...]

ES-3148 User’s Guide 312 Chapter 40 Troublesh ooting[...]

ES-3148 User’s Guide Appendix A 313 A PPENDIX A Product S pecifications These are the switch product specifications. Table 93 General Product Specifications Ethernet Interface 48 10/100 Base-T X interfaces Auto-negotiation Auto-MDI/MDIX Compliant with IEEE 802.3/3u Back pressure flow control for half duplex Flow control for full duplex (IEEE 802.[...]

ES-3148 User’s Guide 314 Table 94 Manageme nt Specifica tions System Control Alarm /S tatus surveillance LED indication for al arm and system status Performance monitoring Line speed Four RMON groups (history , statistics, alarms, and events) Throughput moni toring CMP packet transm ission Port mirroring and aggregation S panning T ree Protocol I[...]

ES-3148 User’s Guide Appendix A 315 Safety ANS/UL 60950-1 CSA 60950-1 EN 60950-1 IEC 60950-1 EMC FCC Pa rt 15 (Class A) CE EMC (Class A) Table 95 Physical and Environmental Specifications (continue d)[...]

ES-3148 User’s Guide 316[...]

ES-3148 User’s Guide 317 A PPENDIX B IP Addresses and Subnetting This appendix introduces IP addresses, IP address classes and subnet masks. Y ou use subnet masks to subdivid e a network in to smaller logical networks. Introduction to IP Addresses An IP address has two parts: the network numb er and the host ID. Routers use the network number to [...]

ES-3148 User’s Guide 318 The following table shows the network number and host ID arrangement for classes A, B and C. An IP address with host IDs of all zeros is the IP address of the n etwork (192.168. 1.0 for example). An IP address with host IDs of all ones is the broadcast address for that network (192.168.1.255 for example). Therefore, to de[...]

ES-3148 User’s Guide 319 Subnet Masks A subnet mask is used to dete rmine which bits are part of th e network number , and which bits are part of the host ID (using a logical AND operation). A subnet mask has 32 bits. If a b it in the subnet mask is a “1” then the correspondi ng bit in the IP address is part of the n etwork number . If a bit [...]

ES-3148 User’s Guide 320 The first mask shown is the class “C” natural m ask. Normally if no mask is specified it is understood that the natura l mask is being used. Example: T wo Subnet s As an example, you have a class “C” address 1 92.168.1.0 wi th subnet mask of 255.255.255 .0. The first three octets of the address ma ke up the networ[...]

ES-3148 User’s Guide 321 Host IDs of all zeros represent the subnet itsel f and host IDs of all ones are the broadcast address for that subnet, so the actual number of hosts available on each subnet in the example above is 2 7 – 2 or 126 h o sts for each subnet. 192.168.1.0 with mask 255.255.255.128 is the subnet itself, and 192.168.1. 127 with[...]

ES-3148 User’s Guide 322 Example Eight Subnet s Similarly use a 27-bit mask to create eight subnets (000, 001, 010 , 01 1, 100, 101, 1 10 and 111 ) . Subnet Address: 192.1 68.1.0 Low est Host ID: 192.168.1.1 Broadcast Address: 192.168.1.63 Highest Host ID: 192.168.1.62 Table 104 Subnet 2 IP/SUBNET MASK NETWORK NUMBER LAST OCTET BIT VA L U E IP Ad[...]

ES-3148 User’s Guide 323 The following table shows class C IP ad dress last octet values for each subnet. The following table is a summary for class “C” subnet planning. Subnetting With Class A and Class B Networks. For class “A” and class “B” addresses the subnet ma sk also determines which bits are part of the network number and whi[...]

ES-3148 User’s Guide 324 The following table is a summary for class “B” subnet planning. Table 109 Class B Subnet Planning NO. “BORROWED” HOST BIT S SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET 1 255.255.128.0 (/17) 2 32766 2 255.255.192.0 (/18) 4 16382 3 255.255.224.0 (/19) 8 8190 4 255.255.240.0 (/20) 16 4094 5 255.255.248.0 (/21) 32 20[...]

ES-3148 User’s Guide Index 325 Index Numerics 10/1000 Ethernet ports 47 802.1p priority 85 A access control limitation 195 login account 198 remote management 206 service port 205 SNMP 196 accounts and modes 232 address learning, MAC 95 Address Resolution Protocol (ARP) 227 , 228 Address Resolution Protocol. See ARP . administrator password 199 a[...]

ES-3148 User’s Guide 326 Index change running config 189 saving 59 , 236 configuration file 60 , 23 6 and commands 236 backup 190 restore 60 , 190 connections hardware 47 console port 37 , 47 commands 229 settings 50 , 229 contact information 8 copying port settings. See port cloning. copyright 3 CPU management port 98 CRC (Cyclic Redundant Check[...]

ES-3148 User’s Guide Index 327 H hardware 37 connections 47 front panel 47 installation 43 installation precautions 44 mounting brackets 44 overview 47 rack-mounting 44 rubber feet 43 transceivers 48 , 49 help 62 in command interpreter 233 web configurator 62 history in command interpreter 236 HTTPS 202 certificates 202 implem entati on 202 publi[...]

ES-3148 User’s Guide 328 Index transceiver installation 48 transceiver removal 49 mirroring ports 123 modes and accounts 232 in command interpreter 232 mounting brackets 44 MSA (MultiSource Agreement) 48 MTU (Multi-T enant Unit) 77 multicast 165 multicast group 169 multicast settings 167 multicast VLAN 173 multicasting 802.1 priority 167 addresse[...]

ES-3148 User’s Guide Index 329 reboot load c onfigur ation 189 reboot system 189 registration product 7 related documentation 31 Remote Authentication Dial In User Service. See RADIUS. remote management 206 service 207 trusted comp uters 207 reset 60 , 188 to factory default settings 188 restore configuration 60 restoring configuration 190 RFC 31[...]

ES-3148 User’s Guide 330 Index setup 21 1 severity levels 21 1 system information 73 system log 209 system login 53 system reboot 189 T tagged VLAN 87 Te l n e t commands 230 logging in 230 management 230 time current 77 time se rver 77 time zone 77 T ime (RFC-868) 77 time se rver 77 time servi ce protocol 77 time format 77 time zone 77 trademark[...]