English dropdown-ico

Zenoah G6200 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Zenoah G6200, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Zenoah G6200 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Zenoah G6200. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Zenoah G6200 should contain:
- informations concerning technical data of Zenoah G6200
- name of the manufacturer and a year of construction of the Zenoah G6200 item
- rules of operation, control and maintenance of the Zenoah G6200 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Zenoah G6200 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Zenoah G6200, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Zenoah service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Zenoah G6200.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Zenoah G6200 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    G6200 G B GB-1 G6200 OWNER’S MANUAL CHAIN SA W G B 848C9F93A0 (807)[...]

  • Page 2

    G6200 GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book before operating this machine. W ear head, e ye and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickback. Read, understand and follow all warnings. APPRO V AL NUMBER OF CE EXHA UST EMISSION REGULA TION (2002/88/EC) e13 * 97/68SH3[...]

  • Page 3

    G6200 G B GB-3 Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 7 4. Fuel and Chain Oil ....................................................[...]

  • Page 4

    G6200 GB-4 10. Keep all parts of your body away from the saw chain when the engine is run- ning. 11. Before you start the engine, make sure the saw chain is not contacting anything. 12. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear , and the muffler away from your body . 13. Always inspect the chain saw[...]

  • Page 5

    G6200 G B GB-5 (3) Make certain that the area in which you are cutting is fr ee from obstruc- tions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw . (4) Cut at high engine speeds. (5) Do not overreach or cut above shoul- der height. (6) Follow the manufacturer[...]

  • Page 6

    G6200 GB-6 2. Explanation of Symbols on the Machine W ARNING • For safe operation and maintenance, symbols are car ved in relief on the machine. According to these indications, please be careful not to make any mistake. The screw under the “H” stamp is The High-speed adjustment scr ew . The port to refuel “MIX GASOLINE” Position: Fuel cap[...]

  • Page 7

    G6200 G B GB-7 5. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 6. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. 7. Tighten the nuts securely with the bar tip held up (12 ~ 15 N·m). Then check the chain [...]

  • Page 8

    G6200 GB-8 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool bef ore refuel- ing the unit. Select outdoor bare ground f or fuel- ing and move at least 3 m (10 ft) a way fr om the fueling point before starting the engine. 4.[...]

  • Page 9

    G6200 G B GB-9 7. Allow the engine to warm up with the throttle lever pulled slightly . W ARNING •K eep clear of the sa w chain as it will start rotating upon starting of engine . ■ CHECKING THE OIL SUPPL Y W ARNING • Make sure to set up the bar and the chain when c hec king the oil supply . If not, the rotating parts may be e xposed. It is v[...]

  • Page 10

    G6200 GB-10 ■ ICING PREVENTION SYSTEM This system prevents icing of the carbur etor which some- times happen while sawing in winter . When your saw has stopped or slowed down abruptly , use the system as follows: 1. Remove the air cleaner cover , air filter , and silencer . 2. Unhook the hatch on the rear wall of the cylinder cover and turn it up[...]

  • Page 11

    G6200 G B GB-11 6. Sawing • Before pr oceeding to your job, read the section “For Safe Op- eration”. It is recommended to first practice sa wing easy logs. This also helps you get accus- tomed to your unit. •A lwa ys follo w the safety regu- lations. The chain saw m ust only be used f or cutting wood. It is forbid den to cut other types of [...]

  • Page 12

    G6200 GB-12 A log lying on the gr ound Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-third and finish by sawing down from the top. In ar ea B, saw down from the top one-third and finish by sawing up fr om the bot- tom. Cutting the limbs of Fallen T ree 2[...]

  • Page 13

    G6200 G B GB-13 ■ PERIODICAL SER VICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause overheat- ing of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover . When installing the cylinder cover , make sure that switch wires and grommets ar e positioned correctly[...]

  • Page 14

    G6200 GB-14 W ARNING • This saw is equipped with one of the f ollowing low kickbac k bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain 16 3670-52112 848CC3LG60 (73LGX) 18 3673-52113 848CC3LG66 (73LGX) 20 3674-52113 848CC3LG72 (73LGX) W ARNING • Be sure to round off the fr ont edge to reduce the c hance of kic kback or tie-[...]

  • Page 15

    G6200 G B GB-15 9. T r oubleshooting Guide Case 1. Starting failure W ARNING • Make sure the icing prevention system is not w orking. 11. Specifications Power unit: Displacement (cm 3 ): ............................................. 62.0 Fuel: ................ Mixture (Gasoline 50 : T wo-cycle oil 1) (when using ZENOAH genuine oil) Fuel tank capa[...]

  • Page 16

    G6200 GB-16 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profes- sionally , and 30 days if used for rental purpose) from the d[...]