Uniden WDECT3355, WDECT3355 manual


Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Uniden WDECT3355, WDECT3355, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Uniden WDECT3355, WDECT3355 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Uniden WDECT3355, WDECT3355. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Uniden WDECT3355, WDECT3355 should contain:
- informations concerning technical data of Uniden WDECT3355, WDECT3355
- name of the manufacturer and a year of construction of the Uniden WDECT3355, WDECT3355 item
- rules of operation, control and maintenance of the Uniden WDECT3355, WDECT3355 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Uniden WDECT3355, WDECT3355 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Uniden WDECT3355, WDECT3355, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Uniden service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Uniden WDECT3355, WDECT3355.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Uniden WDECT3355, WDECT3355 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    WDECT3355 WDECT3355+1 WDECT3355+2 Series Owner ’s Manual OWNER’S MANUAL[...]

  • Page 2

    [ i ] • This symbol indicates important operating and servicing instructions. • The earcap of this telephone may attract and retain small metallic objects. INSTALLATION & SAFETY 3 AVOID - connecting more than phones as ringing may be impaired AVOID - multi power boards. CHARGE - the new phone for 15 - 20 hrs. AVOID - Moisture Don’t - over[...]

  • Page 3

    [ ii ] CONTENTS INSTALLATION & SAFETY i CONTENTS ii Controls and Functions 1 Welcome 3 Features 3 Terminology 4 Mounting the Base Unit on a Wall 5 Battery Maintenance 6 Installing the Beltclip 7 Headset Installation 8 Display and Icons 8 About the Menu Options 9 Setting up the Menu 13 BASICS 21 Making and Receiving Calls 21 Keypad Lock 22 Placi[...]

  • Page 4

    G E T T I N G S T A R T E D [ 1 ] CONTROLS AND FUNCTIONS 2 1 3 5 4 6 7 8 9 10 11 12 22 15 13 18 19 16 20 21 17 14 Repeat Key Delete Key Stop Key Play Key Skip Key Select/ Key 1. Handset Antenna 2. Headset Jack Cover 3. Beltclip Hole 4. Hands-Free Speaker 5. Handset Battery Compartment 6. New Message LED 7. Handset Earpiece 8. LCD Display 9 . /del K[...]

  • Page 5

    [ 2 ] 49 50 33 34 35 36 37 38 39 46 47 48 23 24 25 26 27 28 29 30 32 31 40 41 42 43 44 45 23. Base Speaker 24. Clock/MENU Key 25. repeat/SELECT Key 26. delete Ke y 27. Charge LED 28. Message Counter Display 29. In use L ED 30. play/stop Ke y 31. skip/SELECT K ey 32. SET Key 33. Memo record K ey 34. Ans on/off K ey 35. Greeting Key 36. Mem Key 37. R[...]

  • Page 6

    [ 3 ] Great features of this cordless phone include: • Designed and Engineered in Japan • Wide Band Digital Technology • Multi (4) Handset Capable • Digital Duplex Speakerphone on Handset Advanced Alpha Display Caller ID Features: • Alpha Memory Dialing • POP ID - Caller Name Identification* • 20 Individual Caller Tone Allocation* •[...]

  • Page 7

    [ 4 ] Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology explanation. Standby Mode - The handset is not in use, is off the cradle, and or speaker , or has not been pressed. A dial tone is not present. Talk Mode - The handset is not in the cradle and or speaker , or has been pressed enabling a dial tone. ?[...]

  • Page 8

    [ 5 ] MOUNTING THE BASE UNIT ON A WALL 3mm 100mm 35mm You can mount your base directly to the wall. Before doing this, consider the following: • Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. • Mount your phone within distance of a working phone jack. ?[...]

  • Page 9

    [ 6 ] BATTERY MAINTENANCE Cleaning the battery charging contacts To maintain a good charge, it is important to clean the charging contacts on the handset once a month. Use a dry cloth or pencil eraser to clean. Battery use time (per charge) Fully charged • Up to 7 hours continuous use • Up to 10 days when the handset is in the standby mode (up [...]

  • Page 10

    [ 7 ] INSTALLING THE BELTCLIP To attach the beltclip Insert the beltclip into the holes on each side of the handset. Press down until it clicks into place. To remove the beltclip Pull either side of the beltclip to release the tabs from the holes. Battery replacement and handling When the operating time becomes short, even after a battery is rechar[...]

  • Page 11

    [ 8 ] HEADSET INSTALLATION DISPLAY AND ICONS SUN 12:00A Handset #1 New: 5 :OFF Day of the week and time / batter y icon Handset ID and Banner Number of new Caller ID calls received / Ringer of f icon (when the ringer is Of f) Example of the standby mode display ICON STATUS DESCRIPTION Standby/Talk Battery icon indicates the handset battery status. [...]

  • Page 12

    [ 9 ] There are 6 main menu options, ( DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup and System Reset ) and submenu options. Summary of the Main Menu and Submenu Two Way Communication between the Handsets Anywhere without the Base (DirectLink) DirectLink Mode allows a pair of handsets to work without the base unit, for dir[...]

  • Page 13

    [ 10 ] Handset Setup The following submenu options must be set separately for each handset. Submenu name Description Ringer Tones Adjusting the ringer tone (tone your phone makes when ringing) (Default is Flicker) (see page 15). Set the distinctive ring (see page 15). “Distinctive Ring” allows you to preset memory locations with a designated ri[...]

  • Page 14

    [ 11 ] Answering Setup This main menu option allows you to set up TAD settings from your handset. You can also set these submenu options from the base (see page 44). Submenu name Description Security Code Select a two-digit Personal Identification Number (PIN) code. A PIN code is (Default is 80) required to play your messages from a remote location[...]

  • Page 15

    [ 12 ] Global Setup If you change one of the Global settings, you change the setting for all additional handsets. Only one handset can change Global settings at a time. Submenu name Description Name Tag (POP ID) Display the stored name with the Caller ID telephone number, if the displayed (Default is on) Caller ID telephone number is exactly the sa[...]

  • Page 16

    [ 13 ] Entering the Menu 1) Press the /del key in standby mode. 2) Use /vol/ or /vol/ to move the pointer to a desired main menu ( DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup, and System Reset ). 3) Press to select the desired main menu. 4) Use /vol/ or /vol/ to select a desired submenu, and then press to enter. In the s[...]

  • Page 17

    [ 14 ] Room Monitor Using Room Monitor 1) Enter the Room Monitor menu (see “Entering the Menu” on page 13). To Room Monitor appears. 2) Select the handset you want to monitor by using /vol/ or /vol/ . 3) Press . RoomMonitor appears, and you hear sounds in the room where the handset is installed. 4) To finish the Room Monitor, press or return th[...]

  • Page 18

    [ 15 ] Handset Setup Selecting a Ringer Tone 1) Enter the Handset Setup menu, and then the Ringer Tones submenu (see “Entering the Menu” on page 13). There are 10 ringer tones or 10 polyphonic tones to choose from. - Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder] - Pol ypho nic[...]

  • Page 19

    Setting the Anykey Answer 1) Enter the Handset Setup menu, and then the Anykey Answer submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to select On or Off. 3) Press . You will hear a confirmation tone. Setting the True Banner 1) Enter the Handset Setup menu, and then the Banner submenu (see “Entering the Menu” on page 1[...]

  • Page 20

    [ 17 ] Record Time 1 Minute 4 Minutes Message Alert On Off Ring Time Toll Saver 4 Times Call Screen On Off Setting the Ring Time 1) Enter the Answ. Setup menu, and then the Ring Time submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to select a Ring Time ( Toll Saver, 4 Times, 6 Times , or 9 Times ) . 3) Press . You will hea[...]

  • Page 21

    [ 18 ] Global Setup Setting Name Tag (POP ID) 1) Enter the Global Setup menu, and then the Name Tag submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to change the selection, On or Off . 3) Press . You will hear a confirmation tone. Setting Insert Zero (New Zealand only) 1) Enter the Global Setup menu, and then the Insert 0 [...]

  • Page 22

    [ 19 ] Setting the Dial Mode (Australia only) 1) Enter the Global Setup menu, and then the Dial Mode submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to change the select, Tone or Pulse (the initial setting is Tone). 3) Press . You will hear a confirmation tone. Copy Phonebook 1) Enter the Global Setup menu, and then the Co[...]

  • Page 23

    [ 20 ] System Reset De-register the Handset 1) Enter the System Reset menu, and then the Deregister HS submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to select the handset ID to be de-registered from the list, and then press . Deregister HS? appears. 3) Press /vol/ or /vol/ to select Yes . 4) Press . You will hear a confi[...]

  • Page 24

    This handset has a built-in speakerphone that allows you to have a hands-free conversation. This feature allows you to communicate easily while performing other tasks, such as cooking. appears during hands-free conversations. You can easily switch a call from normal conversation to hands-free conversation. From the Handset Normal conversation Hands[...]

  • Page 25

    [ 22 ] The Keypad Lock prevents user from pressing the keypad accidentally. You can still answer calls, and receive page and phonebook locations, and the keypad lock is reactivated after the operation. To lock the keypad Press and hold tone until you hear a confirmation tone. Keypad Locked appears. If anykey is pressed when keypad is locked, To unl[...]

  • Page 26

    The la st three pho ne numbe rs dialed can be quic kly redia led. Redialing from Standby Mode 1) Press redial/pause in standby mode. 2) Press redial/pause again. Each press of redial/pause will display one of the last three number dialed. 3) Press or speaker . The selected number is dialed. 4) To hang up, press . Redialing from Talk Mode 1) Press o[...]

  • Page 27

    [ 24 ] A D J U S T I N G T H E H A N D S E T R I N G E R , E A R P I E C E A N D S P E A K E R V O L U M E Handset ringer volume Press the volume up key or volume down key (labeled as /vol/ o r /vol/ ) in standby mode to select one of three ringer volume (off, low, or high). Earpiece and speaker volume Pressing the volume up key or volume down key [...]

  • Page 28

    [ 25 ] MUTE MICROPHONE With the handset You can temporarily turn off the microphone so that the person you are talking with cannot hear you. 1) Press /del during talk mode (while phone is in use). 2) Press /vol/ or /vol/ to move the pointer to Mute and then . Mute On and appear in the display. To cancel muting, repeat above step again when Mute is [...]

  • Page 29

    [ 26 ] TONE DIALING SWITCH-OVER (AUSTRALIA ONLY) Some telephone companies use equipment that requires pulse dialing (sometimes referred to as rotary dialing). If you need to enter tone dialing digits, you can switch- over to tone dialing during the call. This feature is useful when you need tone dialing to use automated systems, for example, enteri[...]

  • Page 30

    [ 27 ] Privacy Mode allows you privacy, and guarantee of no interruption from base and other registered handsets. This works only when the phone is in use . 1) Press /del during talk time (while phone is in use). 2) Press /vol/ or /vol/ to move the pointer to Privacy Mode , and then . Privacy Mode On and appear in the display. To exit the Privacy M[...]

  • Page 31

    [ 28 ] FLASH AND CALL WAITING FIND HANDSET If you have Call Waiting service and a call waiting tone sounds during a call: AUSTRALIA: Press on the handset or flash on the base, then press 2 to switch between callers. NEW ZEALAND: Press on the handset or flash on the base to switch between callers. To locate the handset, press mute/find handset on th[...]

  • Page 32

    PHONEBOOK [ 29 ] The Phonebook allows you to dial a number using just a few key presses. Your phone stores names/numbers in the phonebook memory location, and you can search names in alphabetical order. You have a total of 100 locations that can be used for the phonebook (including the speed dials) and Caller ID messages. 1) When the phone is in st[...]

  • Page 33

    [ 30 ] 6) Distinctive Ring appears. Press /vol/ or /vol/ to move the pointer to one of the Distinctive Ring options, and then press . 7) Speed Dial appears. Press /vol/ or /vol/ to move the pointer to select the Speed dial location (10 locations: SPD1-SPD0). 8) Press . You will hear a confirmation tone, and Done! appears in the display. If you choo[...]

  • Page 34

    [ 31 ] ST EPS FOR ENT ERI NG NAME S A ND S PEC IAL CHA RAC TERS Refer to the letters on the number keys to select the desired characters. With each press of a number key ( - ), the displayed character appears in the following order: upper case letters first, lower case letters next and finally the number corresponding to the key. Number of times ke[...]

  • Page 35

    [ 32 ] If the next character uses the same number key, you must press to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set. If you make a mistake while entering a name Use tone or to move the cursor to the incorrect character. Press /del to erase the wrong character and then ent[...]

  • Page 36

    [ 33 ] During a call, don’t press or the call will be disconnected. VIEWING THE PHONEBOOK Your phone stores names/numbers in the phonebook memory locations, and you can search names in alphabetical order. You can view the phonebook even while the phone is in use. 1) Press phonebook . If you recall the phonebook during a call, Store [SELECT] will [...]

  • Page 37

    [ 34 ] MAKING CALLS USING THE PHONEBOOK From Standby Mode 1) When the phone is in standby mode, view the phonebook location to dial (see “Viewing the Phonebook” on page 33). 2) Press o r speaker . The displayed number is dialed. 3) To hang up press . From Talk Mode 1) Press or speaker . 2) View the phonebook location to dial (see “Viewing the[...]

  • Page 38

    [ 35 ] 1) When the phone is in standby mode, press phonebook . 2) Press /vol/ or /vol/ , or the number keypad to view the phonebook locations (see “Viewing the Phonebook” on page 33). a. Editing the Stored Data 1) When the phonebook location to be edited appears, press . Store/Edit Name appears. 2) Follow the steps 3 to 7 under “Storing Phone[...]

  • Page 39

    [ 36 ] CHAIN DIALING The memory locations in the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing. An example of this is a bank account number. Store the account or special number in one of the phonebook locations. [...]

  • Page 40

    [ 37 ] You must subscribe to Caller ID services through your local telephone provider to use these features. When the telephone rings, the Caller ID feature allows you to view the caller’s name, and phone number along with the date and time of call. Additionally, you can dial a number stored in the Caller ID list or save data to your Phonebook lo[...]

  • Page 41

    [ 38 ] VIEWING THE CALLER ID LIST The Caller ID list stores information for incoming calls - even unanswered calls. You can store 100 of the Caller ID messages and Phonebook locations (including SpeedDials) in total. You can view the Caller ID list during a call or when the phone is in standby mode. 1) Press . The summary screen appears. The screen[...]

  • Page 42

    [ 39 ] Deleting Information from the Caller ID List 1) When the phone is in standby mode, view the Caller ID information to be deleted (see “Viewing the Caller ID List” on page 38). 2) Press /del . Delete Caller I D appears. 3) Press /vol/ o r /vol/ to choose Yes . 4) Press . You will hear a confirmation tone. Deleting all Caller ID names/numbe[...]

  • Page 43

    [ 40 ] Calling a party from the Caller ID list From Standby mode 1) When the phone is in standby mode, view the Caller ID message (see “Viewing the Caller ID List” on page 38). 2) Press or speaker . The displayed phone number dials automatically. From Talk mode 1) Press or speaker . 2) View the Caller ID message you want to dial (see “Viewing[...]

  • Page 44

    [ 41 ] The phone has a built-in answering system that answers and records incoming calls. You can also use your answering system to record a conversation, leave a voice memo message or to announce a special outgoing message to callers when you’re away from your phone. Features • Digital Tapeless Recording • Up to 14 Minutes of Recording Time [...]

  • Page 45

    [ 42 ] Answering System Default Settings Some answering system functions can be set through the base or handset. Default settings for each function are as follows: 1) To turn the answering system on, press ans on/off when the phone is in standby mode. After the announcement “Answering System is on,” the current greeting message will be played a[...]

  • Page 46

    [ 43 ] • When the answering system is full, FL appears on the base. You should delete some messages so that the system can record new messages. • Position yourself as near to the base as possible and speak clearly when recording your outgoing message. • If you make an outside call, or a call is received on the base during the operation, the o[...]

  • Page 47

    [ 44 ] For your convenience, voice prompts will guide you through the menu setup mode. 1) When the phone is in standby mode, press /volume/ or /volume/ repeatedly to scroll through ringer volumes. The ringer level is displayed, and you will hear each volume level. The last ringer heard will be the volume setting, then the phone returns to standby m[...]

  • Page 48

    [ 45 ] Setting the Time Follow these steps to set the clock on the answering system to the correct time. 1) Press clock/MENU . 2) Press skip/SELECT or repeat/SELECT until the correct day is announced and the corresponding number (from 1 Sunday to 7 Saturday) appears. 3) Press SET to select the day. 4) Press skip/SELECT or repeat/SELECT until you he[...]

  • Page 49

    [ 46 ] Setting the ring time The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after four, six, nine rings. If you enable the Toll Saver (TS setting), the answering system picks up after six rings if you have new messages, and aft[...]

  • Page 50

    [ 47 ] Announce only feature The Announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set “Announce only”, follow the steps on page 46. To choose between the pre-recorded message or your own personal greeting, press greeting , when the outgoing[...]

  • Page 51

    [ 48 ] Setting the call screen You can screen calls when the Call Screen function is set to On. 1) Press clock/MENU six times. The current Call Screen setting (On or Off) appears on the base. 2) Press skip/SELECT or repeat/SELECT to choose On or OF . 3) Press SET . A confirmation tone sounds, and the system announces the new setting. Screening a ca[...]

  • Page 52

    [ 49 ] The message counter displays the number of messages stored in memory. If the display flashes, then there are new messages waiting for you. The answering system plays your new messages first. After you play all your new messages, you can then play your old messages. Playing your messages 1) When the phone is in standby mode, press play/stop .[...]

  • Page 53

    [ 50 ] Skipping a message 1) Press play/stop to review your messages. The number of stored messages is announced. 2) Press skip/SELECT at anytime to skip to the next message. Each time skip/SELECT is pressed, the system scans forward one message. If you have several messages, press skip/SELECT repeatedly to find the message you want to play. To qui[...]

  • Page 54

    [ 51 ] Voice memo The voice memo function allows the user to record messages (more than 2 seconds and within 4 minutes). 1) Press and hold memo record . You hear a beep. 2) Start your recording after the announcement “Record Memo Message” and a confirmation tone. The message counter displays “- -”. 3) When you have finished, press memo reco[...]

  • Page 55

    [ 52 ] You can check, play, or delete messages, even record a new greeting message from a remote location (when you are away from home, or from another room using a handset). Additionally, you can turn On or Off your answering system remotely. Remote access away from home You can operate your answering system from a remote location using any touch-[...]

  • Page 56

    [ 53 ] * To repeat a message, press # then 1 within about four seconds to repeat the previous message, or press # then 1 after about four seconds to repeat the cur- rent message. ** For the Memo Record and Greeting Message Record functions, the first time you enter the corresponding command, it starts the Recording function. If you want to stop the[...]

  • Page 57

    [ 54 ] * For Repeat a Message function, press 1 within about four seconds to repeat the previous message, or press 1 after about four seconds to repeat the current message. ** For Memo Record and Greeting Message Record function, the first time you enter the corresponding command, it starts the Recording function. If you want to stop the recording,[...]

  • Page 58

    [ 55 ] 4 Multi-Handset Expendability Your phone supports up to 4 handsets (including the handset(s) supplied with your phone). You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger. Up to 2 handsets can be used for outside and/or intercom call. Effective combination, for example: - 4-way c[...]

  • Page 59

    REGISTER THE HANDSET If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. The handset ID for the supplied handset(s) was assigned at the factory, which has #1 or #2 in the display (#2 for models that have two handsets in packaging). When you register additional hand[...]

  • Page 60

    [ 57 ] To use this feature, you must enter the two handsets into the DirectLink mode first. To enter the DirectLink mode • See page 13 This feature allows you to monitor sounds in another room. To use this feature, place the handset or base in the desired room to monitor (act an remote mic), and place the other near listener (remote speaker). For[...]

  • Page 61

    [ 58 ] 4-WAY CONFERENCING INTERCOM/CALL TRANSFER FEATURE Fourth person, at either the handset or the base, may be added to the conference call. For example, to add a fourth party to an ongoing conference call at the base or another handset, press on the fourth party’s handset (or on the base). To remove either caller from your conversation, press[...]

  • Page 62

    [ 59 ] Call Transfer Feature From handset to handset or to the base 1) During a call, press /transfer/int’com on the handset. 2) Select a handset or the base to transfer the call within 10 seconds. (Refer to step 2 in the intercom section on page 58). The call will automatically be placed on hold, and an intercom tone sounds. To cancel the transf[...]

  • Page 63

    [ 60 ] The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. To change the digital security code: 1. Perform the “System Reset” menu[...]

  • Page 64

    [ 61 ] NOTE ON POWER SOURCES Battery replacement and handling When the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery. Warning To avoid the risk of p[...]

  • Page 65

    [ 62 ] TROUBLESHOOTING If your phone is not performing to your expectations, please try these simple steps first. Symptom Suggestion The charge LED won’t illuminate • Make sure the AC adapter is plugged into the base or charger and wall when the handset is placed in outlet. the cradle. • Make sure the handset is properly seated in the cradle.[...]

  • Page 66

    [ 63 ] Symptom Suggestion Severe noise interference. • Keep the handset away from microwave ovens, computers, remote control toys, wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical appliances. • Move to another location or turn off the source of interference. The Caller ID does not display. • Th[...]

  • Page 67

    [ 64 ] Symptom Suggestion Messages are incomplete. • The incoming messages may be too long. Remind callers to leave a brief message. • The memory may be full. Delete some or all of the saved messages. No sound on the base unit • Adjust the speaker volume on the base unit. speaker during call monitoring • Make sure the call screen feature is[...]

  • Page 68

    [ 65 ] INDEX 0 - 9 3-way conferencing ................... 27 4-way conferencing ................... 58 20 ring options .......................... 15 A Announce only feature .............. 47 Answering system Deleting a message ................ 50 Playing your messages ........... 49 Recording a conversation ....... 51 Remote access ................[...]

  • Page 69

    [ 66 ] REMOTE OPERATION CARD CUT REMO TE OPERA TION CARD Remote access away fr om home 1. Call your phone number from a touch-tone phone. 2. During t he outgoing message, press # and enter your PIN code. The answering system announces the number of messages stored in memor y and the help guidance. 3. To quit, hang up the phone. Turn on the answ eri[...]

  • Page 70

    [ 67 ] CUT T as k Ke y Repeat a Message Playing incoming Messages Skipping a Message Deleting a Message Stop Operation Answering Sys tem On Memo Record/S top Greeting Message R ecord/Stop Answer Sys tem Of f Help Guidance[...]

  • Page 71

    [ 68 ] WARRANTY One Year Limited Warranty UNDIEN WDECT3355/WDECT3355+1/WDECT3355+2 CORDLESS PHONE Important: Evidence of original purchase is required for warranty service. Warrantor: Uniden Australia Pty Limited A.B.N. 58 001 865 498 Uniden New Zealand Limited Warranty only available in original country of purchase. ELEMENT OF WARRANTY : Uniden wa[...]

  • Page 72

    ©2007 Uniden Australia Pty Limited/Uniden New Zealand Limited Part Code UPZZ01459BZ(0) Printed in China[...]