Ultra electronics MAGICARD Sprinter manual

1
2
3
4
5
6
7
8

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Ultra electronics MAGICARD Sprinter, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Ultra electronics MAGICARD Sprinter one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Ultra electronics MAGICARD Sprinter. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Ultra electronics MAGICARD Sprinter should contain:
- informations concerning technical data of Ultra electronics MAGICARD Sprinter
- name of the manufacturer and a year of construction of the Ultra electronics MAGICARD Sprinter item
- rules of operation, control and maintenance of the Ultra electronics MAGICARD Sprinter item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Ultra electronics MAGICARD Sprinter alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Ultra electronics MAGICARD Sprinter, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Ultra electronics service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Ultra electronics MAGICARD Sprinter.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Ultra electronics MAGICARD Sprinter item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 I MAGICARD PRINTER INSTRUCTIONS FOR REPLACEMENT OF PRINTHEAD AND PRINTHEAD ASSEMBLIES WARNIN G - The Magicard colour printer contai ns hazardous voltages. CAUTI ON - The following procedures involve contact with Electrostatic Sensitive Devices. All Precautions for han[...]

  • Page 2

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 II 1. (a) Removing the cover Magicard 300 and Sprinter models. (1) Set the printer On/Off switch to off(0) and isolate from the mains supply. Remove the card cassette and Dye-Film from the printer. (2) Position the printe r on its side with the rear of the pr inter fa[...]

  • Page 3

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 III 1. (b) Removing the cover Magicard Turbo models. (1) Set the printer On/ Off switch to Off(O) and isolate from the mains supply. Rem ove the card cassette and the Dy e-Film from the printer. (2) Position the printer upside down with the rear of the printer facin g[...]

  • Page 4

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 IV 2. Removing old printhead/assembly (1) Remove the dy e-film and dye-film carrier from the printer. (2) If a tye-wrap is fitted to the grey ribbon cable plug on the back of the printhead, cut this tye-wrap taking great care not to cut the ribbon cable itself. (3) Di[...]

  • Page 5

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 V 3. Fitting the new printhead to the heatsink assembly (Magicard Dealers Only) CAUTION - The following procedures involve contact with the new printhead, all precautions for handling Electrostatic Sensit ive Devices sh ould be follow ed at all times, including the us[...]

  • Page 6

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 VI (3) Che ck that t h e springs at th e ba ck of the pr inthe ad asse mbly are neat ly compressed and are not bulging outwards or inwards. If t hey are bulging the assembly will ha ve to be removed and refitted again until they remain neatly compressed. (4) If a head[...]

  • Page 7

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 VII (4) The printhead angle has been f actory set. In order to ensure that it is still correct, compare the test card with th e images on the back page of this docu ment. N.B. If your test card shows a completely different test image from those on the back page, you w[...]

  • Page 8

    3461/07/01 ISSUE 2 PRINTHEAD INSTALLATION & COMMISSIONING SPEC. DCR No. 26106 VIII 7. And finally..... If your new thermal printhead fails to produce a good test image after following the above steps t hen please contact your suppli er. Too Positive Dark patches stressing out from the rear edge of the green square (watermarking). These patches [...]