English dropdown-ico

Toshiba B-SV4T manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Toshiba B-SV4T, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Toshiba B-SV4T one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Toshiba B-SV4T. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Toshiba B-SV4T should contain:
- informations concerning technical data of Toshiba B-SV4T
- name of the manufacturer and a year of construction of the Toshiba B-SV4T item
- rules of operation, control and maintenance of the Toshiba B-SV4T item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Toshiba B-SV4T alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Toshiba B-SV4T, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Toshiba service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Toshiba B-SV4T.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Toshiba B-SV4T item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    TOSHIBA Barcode Printer B-SV4T SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente Manual do Utilizador[...]

  • Page 2

    TOSHIBA Barcode Printer B-SV4T SERIES Owner’s Manual[...]

  • Page 3

    CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • Schallemission: unter 70dB (A ) nach DIN 45635 (oder ISO 7779) • Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Copyright © 2006 by TOSHIBA TEC [...]

  • Page 4

    Safety Summary ENGLISH VERSION EO1-33062 ( ) i Safety Summary Personal safety in handling or maintaining the equipmen t is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and underst ood before handling or maintaining the equipm ent[...]

  • Page 5

    Safety Summary ENGLISH VERSION EO1-33062 ( ) ii If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or e[...]

  • Page 6

    ENGLISH VERSION EO1-33062 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW .......................................................................................................... E1 -1 1.1 Introduction .............................................................................................................. ...... E1-1 1.2 Features ...............[...]

  • Page 7

    ENGLISH VERSION EO1-33062 APPENDIX 2 INTERFACE .......................................................................................................... E A2-1 GLOSSARIES INDEX CAUTION! 1. This manual may not be copied in whole or in par t without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notifi[...]

  • Page 8

    1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.1 Introduction E1- 1 1. PRODUCT OVERVIEW 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories Thank you for choosing the TOSHIBA B-SV4T series barcode printer. This Owner’s Manual contains valuab le information from general set-up to confirming the printer's operation us ing test prints.[...]

  • Page 9

    1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.4 Accessories E1- 2  When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your Authorised TOSHIBA TEC representative. (As of September 2004) Country Agency Certification mark Country Agency Certi[...]

  • Page 10

    1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.5 Appearance E1- 3 1.5 Appearance 1.5.1 Dimensions 1.5.2 Front View 1.5.3 Rear View The names of the parts or units introdu ced in this section are used in the following chapters. Dimensions in mm (inches) Power Jack Power Switch Rear Media Guide Parallel Interface Connector (Centronics) USB Interface[...]

  • Page 11

    1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33062 1.5 Appearance E1- 4 1.5.4 Interior 1.5.5 Button and Indicator Lamp The FEED/PAUSE Button and the Indicator Lamp have the following functions: As the FEED button • Pressing this button when the printer is in online state causes a media feed. • Pressing this button after removing a cause of an error [...]

  • Page 12

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.1 Precautions E2- 1 2. PRINTER SETUP 2.1 Precautions This section outlines the steps necessary to setup your printer prior to its operation. The section includes precautions, connecting cables, assembling accessories, loading media and ribbon, and performing a test print. To insure the best operating env[...]

  • Page 13

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.2 Procedure before Operation E2- 2 2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF 2.3.1 Turning ON the Printer This section describes the outline of the printer setup. 1. Unpack the accessories and printer from the box. 2. Refer to Safety Precautions in this manual and set up the printer a[...]

  • Page 14

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.4 Connecting the Cables to the Printer E2- 3 2.3.2 Turning OFF the Printer 2.4 Connecting the Cables to the Printer 1. Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing. 2. To turn OFF the printer power press the power switch as shown in the [...]

  • Page 15

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.5 Connecting the Power Adapter and the Power Cord E2- 4 2.5 Connecting the Power Adapter and the Power Cord 1. Make sure that the printer power switch is in the OFF (O) position. 2 . Insert the Power Cord into th e inlet of the Power Adapter. 3. Insert the Power Adapter connector into the Power Jack on t[...]

  • Page 16

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.6 Opening/Closing the Top Cover E2- 5 2.6 Opening/Closing the Top Cover When opening or closing the Top Cover, please be sure to follow the instructions below. To open the Top Cover: 1. Turn the Cover Open Levers fr ontward, and gradually open the Top Cover. There are four positions for the Top Cover: OP[...]

  • Page 17

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.6 Opening/Closing the Top Cover E2- 6 2.6 Opening/Closing the Top Cover (Cont.) To hold the Top Cover at Position 2, first open the Top Cover until the Top Cover Support goes over Position 2 ( c ), then close the Top Cover a little ( d ) to secure the Top Cover Support. To close the Top Cover: 1. Open th[...]

  • Page 18

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2- 7 2.7 Loading the Media This section describes in detail how to load a media roll. 1. Turn OFF the printer. 2. Turn the Cover Open Levers fr ontward, and open the Top Cover. 3. When the inner core diameter of the media roll is 25.4 mm (1”), remove the Media Holder Spacers from t[...]

  • Page 19

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2- 8 2.7 Loading the Media (Cont.) 6. Insert the both ends of the Media Shaft into the slots of the printer to place the Media Holder A ss’y into th e printer. Make sure that the media feeds from the top, as shown below. 7. Insert the leading edge of the media under the Media Hold [...]

  • Page 20

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2- 9 2.7 Loading the Media (Cont.) 11. After loading the media, manually set the Media Sensor to the correct position. The Feed Gap Sensor is included in the right Media Guide. Position of the Feed Gap Sensor can be set by fitting the Media Guides to the media ends. When using the Bl[...]

  • Page 21

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2-10 Strip Feed Roller 2.7 Loading the Media (Cont.) Strip mode (Option): When issued in the strip mode, labels are automatically removed from the backing paper each time a label is printed. • How to set the media When issuing labels in the strip mode, set the label in the followin[...]

  • Page 22

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2-11 2.7 Loading the Media (Cont.) Cut mode (Option): When the Cutter is installed, th e media is automatically cut. After loading the media as described on the previous pages, insert the leading edge of the media through the Media Outlet of the Cutter Cover. CAUTION ! 1. Be sure to [...]

  • Page 23

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.7 Loading the Media E2-12 2.7 Loading the Media (Cont.) When a media roll has an outside diameter exceeding 127 mm (5 ” ) or an inner core diameter of 38.1 mm (1.5 ” ), the optional External Media Roll Hanger is required. 1. Fit the protrusions on the bottom of the printer into the holes in the Exter[...]

  • Page 24

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.8 Loading the Ribbon E2-13 2.8 Loading the Ribbon When the printer is turned on, it automatically detects whether a ribbon is installed or not and switches the printing method between thermal transfer or direct thermal. If the printer does not detect a ribbon (direct thermal mode), the m otor that drives[...]

  • Page 25

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.8 Loading the Ribbon E2-14 2.8 Loading the Ribbon (Cont.) 5. Pull the leader tape of the ribbon downward, and feed it under the Print Head. 6. Attach the leader tape to the Paper Core with adhesive tape. 7. Rotate the Paper Core to take up the ribbon leader tape until it is thoroughly covered by the blac[...]

  • Page 26

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities E2-15 2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities 2.9.1 Media Sensor Calibration 2.9.2 Self Print Test and Dump Mode This utility is used to calibrate th e sensitivity of the Feed Gap/Black Mark Sensor. It is [...]

  • Page 27

    2. PRINTER SETUP ENGLISH VERSION EO1-33062 2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities E2-16 2.9.2 Self Print Test and Dump Mode (Cont.) Print test label sample The test print contents should be changed by the following commands and parameters: PROGRAM VERSION: VX.XX XXXX --- Fi rmware version and checksum TONE ADJUST: +X[...]

  • Page 28

    3. MAINTENANCE ENGLISH VERSION EO1-33062 3.1 Cleaning E3- 1 3. MAINTENANCE 3.1 Cleaning 3.1.1 Print Head This chapter describes how to pe rform routine maintenance. To ensure the continuous high quality operation of your printer, you should perform a regular maintenance routine. For high throughput it should be done on a daily basis. Fo r low throu[...]

  • Page 29

    3. MAINTENANCE ENGLISH VERSION EO1-33062 3.1 Cleaning E3- 2 3.1.2 Platen/Sensors 3.1.3 Cover 1. Wipe the Platen with a soft cloth moistened with absolute alcohol. 2. Remove dust or paper particles fro m the Black Mark Sensor, Feed Gap Sensor, and Ribbon Sensor using an air blower. Wipe the Cover with a dry soft cloth. Wipe off dirt with a soft clot[...]

  • Page 30

    3. MAINTENANCE ENGLISH VERSION EO1-33062 3.2 Care/Handling of the Media and Ribbon E3- 3 3.2 Care/Handling of the Media and Ribbon • Do not store media or ribbons for longer than the manufacturer’s recommended shelf life • Store media rolls on the flat end. Do not store them on the curved sides as this might flatten that side causing erratic [...]

  • Page 31

    4. TROUBLESHOOTI NG ENGLISH VERSION EO1-33062 4.1 Troubleshooting Guide E4- 1 4. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions. 4.1 Troubleshooting Guide Problems Solutions The Online Indicator Lamp (green) is not illuminated. 1. Check that the Power Cord is properly connected. 2. If the LED on the AC[...]

  • Page 32

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.1 Printer EA1- 1 APPENDIX 1 SPECIFICATIONS Appendix 1 describes the printer specifications and supplies for use on the B-SV4T printer. A1.1 Printer The following are the printer specifications. Item Specifications AC100 to 240V, 50/60 Hz 100 to 120V: 2.1 A, 49.0 W maximum , 200 to 240V: 2.1 A, [...]

  • Page 33

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.2 Options EA1- 2 A1.2 Options Option Name Type Description Keyboard display unit KB-75-QM-R This m odule is an external intelligent keyboard display unit. Cutter module B-SV204-QM-R B-SV404-QM-R A cutter unit that makes stub cuts. A cutter unit that makes normal cuts. Strip module B-SV404-H-QM-[...]

  • Page 34

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.3 Media EA1- 3 A1.3.1 Media Type (Cont.) Unit: mm (inch) Issue mode Item Batch mode Strip mode Cut mode c Width including backing paper 20 to 112 (0.8 to 4.4) d Media width 17 to 109 (0.7 to 4.3) Label 12 to 609.6 (0.5 to 24.0) 27.4 to 154.4 (1.1 to 6.1) 27.4 to 609.6 (1.1 to 24.0) e Media pitc[...]

  • Page 35

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.3 Media EA1- 4 A1.3.3 Detection Area of the Reflective Sensor The Reflective Sensor is movable within the full range of the media width. The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm. The Reflective Sensor should be aligned with the centre of the [...]

  • Page 36

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33062 A1.4 Ribbon EA1- 5 A1.3.4 Effective Print Area The figure below illustrates the relation between th e head effective print width and media width. The figure below shows the effective print area on the media. A1.4 Ribbon Please make sure that the ribbon being used is approved by TOSHIBA TEC. The wa[...]

  • Page 37

    APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33062 APPENDIX 2 INTERFACE EA2- 1 APPENDIX 2 INTERFACE  Interface Cables To prevent radiation and reception of electrical no ise, the interface cables must meet the following requirements: • Fully shielded and fitted with meta l or me tallized connector housings. • Keep as short as possible. • Shoul[...]

  • Page 38

    GLOSSARIES ENGLISH VERSION EO1-33062 GLOSSARIES GLOSSARIES Bar code A code which represents alphanumeric characters by using a series of black and white stripes in different widths. Bar codes are used in various industrial fields: Manufacturing, Hospitals, Libraries, Retail, Transpor tation, Warehousing, etc. Reading bar codes is a fast and accurat[...]

  • Page 39

    GLOSSARIES ENGLISH VERSION EO1-33062 GLOSSARIES Supply Media and ribbon Tag A type of media having no adhesive backing but black marks to indicate the print area. Usually tags are made of cardboard or other durable material. Thermal print head A print head using thermal transfer or thermal direct printing method. Thermal transfer printing A printin[...]

  • Page 40

    INDEX ENGLISH VERSION EO1-33062 INDEX INDEX B Backing paper 2-10, A1-3 Bar code A1-1 Batch mode 2-6 Black mark 2-9, 2-15, A1-2, A1-4 Black mark length A1-3 Black mark sensor 1-4, 2-8, 2-9, 2-15, 3-2 C Centronics 1-3, 2-2, 2-3, A1-1 Cover open sensor 1-4 Cut mode 2-11, A1-1, A1-3 Cutter module A1-2 D Dimensions 1-3, A1-1 Direct thermal A1-1 E Effect[...]

  • Page 41

    INDEX ENGLISH VERSION EO1-33062 INDEX S Serial interface 1-3, 2-3, A1-1 Strip mode 2-10, A1-3 Supply voltage A1-1 T Tag paper A1-2 Thermal transfer A1-1 Top cover support 1-4, 2-5, 2-6 3”-diameter media shaft 2-12, A1-3 Two-dimensional code A1-1 U USB interface 1-3, 2-3, A1-1 W Weight A1-1[...]

  • Page 42

    E EO1-33062[...]