Telit Wireless Solutions GE863-QUAD manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Telit Wireless Solutions GE863-QUAD, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Telit Wireless Solutions GE863-QUAD one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Telit Wireless Solutions GE863-QUAD. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Telit Wireless Solutions GE863-QUAD should contain:
- informations concerning technical data of Telit Wireless Solutions GE863-QUAD
- name of the manufacturer and a year of construction of the Telit Wireless Solutions GE863-QUAD item
- rules of operation, control and maintenance of the Telit Wireless Solutions GE863-QUAD item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Telit Wireless Solutions GE863-QUAD alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Telit Wireless Solutions GE863-QUAD, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Telit Wireless Solutions service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Telit Wireless Solutions GE863-QUAD.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Telit Wireless Solutions GE863-QUAD item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    GE863-QUAD GE863-PY Hardware User Guide 1vv0300715 Rev. 1 - 19/09/06[...]

  • Page 2

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 2 of 79 Contents 1 Overview ....................................................................................................................... .... 6 2 GE863 module c onnections ..........[...]

  • Page 3

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 3 of 79 7.4 Microphone Biasing ............................................................................................................. ... 36 7.4.1 Balanced Microph one Biasing ..........[...]

  • Page 4

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 4 of 79 12 Camera ......................................................................................................................... ... 60 12.1 Transchip Camera ........................[...]

  • Page 5

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 5 of 79 This document is relating to the following products: GE863-QUAD Pb free 3 990 250 662 GE863-PY Pb free 3 990 250 66 1[...]

  • Page 6

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 6 of 79 1 Overview The aim of this document is the description of some hardware solutions useful for developing a product with the Telit GE863-QUAD/PY module . In this document all the basic fu[...]

  • Page 7

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 7 of 79 2 GE863 module connections 2.1 PIN-OUT Pin Signal I/O Function Internal Pull up Typ e 1 GPIO13 I/O GPIO13 CMOS 2.8V 2 GPIO12 I/O GPIO12 CMOS 2.8V 3 GPIO11 I/O GPIO11 CMOS 2.8V 4 GPIO10 [...]

  • Page 8

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 8 of 79 Pin Signal I/O Function Internal Pull up Typ e 28 GND - Ground Power 29 STAT_LED O Status indicator led CMOS 1.8V 30 AXE I Handsfree switching 100K Ω CMOS 2.8V 31 VAUX1 - Power output [...]

  • Page 9

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 9 of 79 Pin Signal I/O Function Internal Pull up Typ e 59 GPIO17 I/O GPIO CMOS 2.8V 60 GPIO14 I/O GPIO - 61 RESERVED - RESERVED - 62 RESERVED - RESERVED - 63 DAC_OUT O DAC out 64 GPIO16 I/O GPI[...]

  • Page 10

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 10 of 79 2.2 PINS LAYOUT[...]

  • Page 11

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 11 of 79 3 Hardware Commands 3.1 Turning ON the GE863-QUAD/PY To turn on the GE863-QUAD/PY the pad ON# must be tied low for at least 1 second and then released. The maximum current that can be [...]

  • Page 12

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 12 of 79 1- Let's assume you need to drive the ON# pad with a totem pole output of a +3/5 V microcon troller (uP_OUT1): 2- Let's assume you need to drive the ON# pad directly with an [...]

  • Page 13

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 13 of 79 • by software command (see GE863-QUAD/PY Software User Guide) • by hardware shutdown When the device is shut down by software command or by hardware shutdown, it issues to the netw[...]

  • Page 14

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 14 of 79 NOTE: don't use any pull up resistor on the RE SET# line nor any totem pole digital output. Using pull up resistor may bring to la tch up problems on the GE863-QUAD/PY power regul[...]

  • Page 15

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 15 of 79 4 Power Supply The power supply circuitry and board layout are a very important part in the full product design and they strongly reflect on the product overall perfo rmances, hence re[...]

  • Page 16

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 16 of 79 4.2 General Design Rules The principal guidelines for the Power Supply Design embrace three different design steps: - the electrical design - the thermal design. - the PCB layout. 4.2.[...]

  • Page 17

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 17 of 79 An example of linear regulator with 5V input is: 4.2.1.2 + 12V input Source Power Supply Design Guidelines • The desired output for the power supply is 3.8V, hence due to the big dif[...]

  • Page 18

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 18 of 79 An example of switching regulator with 12V input is: 4.2.1.3 Battery Source Power Supply Design Guidelines • The desired nominal output for the power supply is 3.8V and the maximum v[...]

  • Page 19

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 19 of 79 4.2.1.4 Battery Charge control Circuitry Design Guidelines The charging process for Li-Ion Batteries can be divided into 4 phases: • Qualification and trickle charging • Fast charg[...]

  • Page 20

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 20 of 79 As you can see, the charging process is not a tr ivial task to be done; moreover all these operations should start only if battery temperature is inside a charging range, usually 5°C [...]

  • Page 21

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 21 of 79 4.2.3 Power Supply PCB layout Guidelines As seen on the electrical design guidelines the pow er supply shall have a low ESR capacitor on the output to cut the current peaks and a prote[...]

  • Page 22

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 22 of 79 5 Antenna The antenna connection and board layout design are the most important part in the full product design and they strongly reflect on the product overall performances, hence rea[...]

  • Page 23

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 23 of 79 This device is to be used only for mobile and fixed application. The ante nna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all[...]

  • Page 24

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 24 of 79 • MODEM SERIAL PORT • MODEM SERIAL PORT 2 (DEBUG) 6.1 MODEM SERIAL PORT Several configurations can be designed for the serial port on the OEM hardware, but the most common are: •[...]

  • Page 25

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 25 of 79 The signals of the GE863-QUAD/PY serial port are: RS232 Pin Number Signal GE863- QUAD/PY Pad Number Name Usage 1 DCD - dcd_uar t 42 Data Carrier Detect Output from the GE863-QUAD/PY th[...]

  • Page 26

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 26 of 79 6.2 MODEM SERIAL PO RT 2 (Python Debug) It is available on the following pins: PIN # NAME DESCRIPTION TYPE 25 TX_TRACE TX Data CMOS 2.8V 26 RX_TRACE RX Data CMOS 2.8V 6.3 RS232 level t[...]

  • Page 27

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 27 of 79 NOTE: In order to be able to do in circui t reprogramming of the GE863-QUAD/PY firmware, the serial port on the Telit GE 863-QUAD/PY shall be available for translation into RS23 2 and [...]

  • Page 28

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 28 of 79 The RS232 serial port lines are usually connected to a DB9 connector with the follow ing layout: 6.4 5V UART level translation If the OEM application uses a microcontroller with a seri[...]

  • Page 29

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 29 of 79 and for a 5V receiver: NOTE: The UART input line TXD (rx_uart) of the GE863-QUAD/PY is NOT internally pulled up with a resistor, so there may be the need to place an external 47K Ω p[...]

  • Page 30

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 30 of 79 7 Audio Section Overview The Base Band Chip of the GE863-QUAD / PY Telit M odule provides two different audio blocks; both in transmit ( Uplink ) and in receive ( Downlink ) direction:[...]

  • Page 31

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 31 of 79 G E 8 6 3 - G P S A u d io P a th s D iffe r e n tia l L in e -O u t D riv e rs F u lly D iffe r e n tia l P o w e r B u ffe rs EXTERNAL AMPLIFIER - 1 2 d B F S 1 6 8 1 6 + 1 0 d B - 4[...]

  • Page 32

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 32 of 79 7.1 Microphone Paths Characteristic and Requirements TIP: being the microphone circuitry the more noise sensitive , its design and layout must be done with particular care. Both microp[...]

  • Page 33

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 33 of 79 TIP: definition of the nominal sensitivity of the microphone lines . The nominal sensitivity of the microphone lines indicates the voltage level on the GE863-QUAD / PY pins present dur[...]

  • Page 34

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 34 of 79 TIP: environment consideration . For hands-f ree/car kit microphone, you must take into account the voice attenuation, due to the distance between the microphone itself and the talker [...]

  • Page 35

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 35 of 79 7.2 General Design Rules There are several configurations for the audio paths, but the most effective difference is between balanced and unbalanced microphone configuration. It is high[...]

  • Page 36

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 36 of 79 7.4 Microphone Biasing The electret microphones usually need a biasing voltage to work properly. Refer to your microphone provider for the characteristics required. NOTE: The microphon[...]

  • Page 37

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 37 of 79 NOTE: The cable to the microphone should not be shielded, instead a twisted pair cable shall be used. NOTE: The microphone sensitivity changes with the value of R2 and R3. Usually the [...]

  • Page 38

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 38 of 79 NOTE: In the unbalanced application the capacitor C3 shall be > 200nF otherwise the frequency response will be cut at low band frequencies (down to 300Hz). This capacitor can be pla[...]

  • Page 39

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 39 of 79 7.5 Microphone Buffering As seen previously, a microphone shall be connected to the input pins of the GE863-QUAD / PY through a buffer amplifier that boosts the signal level to the req[...]

  • Page 40

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 40 of 79 The buffer gain is given by the formula: 607 606 605 604 R R R R Gain = = The C636 and C637 capacitors are placed in order to cut off the gain at higher frequencies than the transmitte[...]

  • Page 41

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 41 of 79 7.5.2 Buffered Unbalanced (Single Ended) Microphone . The above schematic can be used for a single ended ( buffere d unbalanced ) microphone ; the required biasing circuitry is not inc[...]

  • Page 42

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 42 of 79 727 * 711 * 2 1 726 * 719 * 2 1 . C R C R freq π π = = [Hz] The buffer bandwidth at -3dB shall be 4KHz. Note that the biasing of the operational amplifier is given for the inverting [...]

  • Page 43

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 43 of 79 As a consequence of the assigned values of the resistors, the nominal values of C726 and C727 are : C726 = 1/ (2 π *4000*R719)= 7.10 *10 -9 F C727 = 1/ (2 π *4000*R711)= 2,65 *10 -9 [...]

  • Page 44

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 44 of 79 8 OUTPUT LINES (Speaker) 8.1 Short description The Telit GE863-QUAD / PY provides two audio paths in receive section. Only on e of the two paths can be active at a time, selectable by [...]

  • Page 45

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 45 of 79 8.2 Output Lines Characteristics “Ear_MT” Differential Line-out Drivers Path • line coupling: DC • line type: bridged • output load resistance : ≥ 14 Ω • internal outpu[...]

  • Page 46

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 46 of 79 8.3 General Design Rules There are several configurations for the audio output path, but the variou s design requirements can be grouped into three different categories: • handset ea[...]

  • Page 47

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 47 of 79 8.4 Handset Earphone Design As seen previously, a 16 Ω earpiece can be directly connected to the output pads EAR_MT+ and EAR_MT- of the GE863-QUAD / PY . This solution is often the m[...]

  • Page 48

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 48 of 79 The resulting gain and high pass cut can be obtained with the formula: 2 3 R R Gain = 4 * 3 * 2 1 . C R freq π = [Hz] And an example of internal Ear amplifier could be : Some amplifie[...]

  • Page 49

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 49 of 79 8.6 Car Kit Speakerphone Design For the car kit speaker phone function the power output requirement is usually at least 4W, therefore an amplifier is needed to boost the GE863-QUAD / P[...]

  • Page 50

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 50 of 79 8.7 The Evaluation Kit for Telit Modules EVK2 8.7.1 Short Description Telit supplies the Evaluation Kit for Telit modules EVK2 to assist the designer to develop his own applications ba[...]

  • Page 51

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 51 of 79 The ASC1 port is used for: - Continuous of debug messages of the PYTHON Script Interpreter (requires PYTHON version modules; For further detailed description refer to Technical Specifi[...]

  • Page 52

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 52 of 79 9 SIM DESIGN GUIDES In all Telit modules there are five pins for SIM card holder connection These lines are: SIMVCC (SIM Power supply) SIMRST (SIM Reset) SIMIO (SIM Data) SIMIN (SIM Pr[...]

  • Page 53

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 53 of 79 9.4 SIM Supply Do not connect capacitance greater than 10nF to SIMVCC line. Other notes: - SIMIN doesn't require any pull-up resistor. It is built in. - SIM card is detected inser[...]

  • Page 54

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 54 of 79 9.6 LAYOUT[...]

  • Page 55

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 55 of 79 10 General Purpose I/O The general purpose I/O pads can be configured to act in three different ways: - input - output - alternate function (internally controlled) Input pads can only [...]

  • Page 56

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 56 of 79 10.3 Using the Alarm Output GPIO6 The GPIO6 pad, when configured as Alarm Output, is controlled by the GE863-QUAD / PY module and will rise when the alarm starts and fall after the iss[...]

  • Page 57

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 57 of 79 11 DAC and ADC section 11.1 DAC Converter 11.1.1 Description The GE863-QUAD / PY module provides a Digital to Analog Converter. The signal (named DAC_OUT) is available on BGA Ball #63 [...]

  • Page 58

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 58 of 79 11.1.2 Enabling DAC An AT command is available to use the DAC function. The command is AT#DAC[=<enable>[,<value>]] <value> - scale factor of the integrated output vol[...]

  • Page 59

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 59 of 79 11.2 ADC Converter 11.2.1 Description The GE863-QUAD / PY module provides 3 Analog to Digital Converters. The input lines are available on: ADC_IN1 on BGA Ball #23 of the GE863-QUAD / [...]

  • Page 60

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 60 of 79 12 Camera 12.1 Transchip Camera The GE863-QUAD / PY provides a direct support for Transchip digital cameras with the following characteristics: Type: TRANSCHIP TC5747 Technology: CMOS [...]

  • Page 61

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 61 of 79 12.1.1 Camera Interface Connectors The pinout of the module and a 24 pins ZIF conn ector for the CMOS camera provide the interface connection between GE863-QUAD / PY and Transchip cam [...]

  • Page 62

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 62 of 79 Fig 1. Camera Physical Detail & Connector Fig 2. Camera Socket Connector[...]

  • Page 63

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 63 of 79 12.1.2 EVB for Transchip camera support In order to interface the Telit GE863-QUAD / PY with a CMOS camera, Telit has developed an evaluation board. The EVK allows the connector of all[...]

  • Page 64

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 64 of 79 12.1.3 Block Diagram for supported cameras The numbers on the left side of the Camera’s connectors refers to Module Connector’s pin number. DVDD is VAUX1 power supply from GE863-QU[...]

  • Page 65

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 65 of 79 12.1.4 Schematic Diagrams for supported camera[...]

  • Page 66

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 66 of 79 12.1.5 Example usage script for camera Camera setting: (shown here are the defaults ones) >AT#CAMSEL=0 (camera selection: 0-auto, 1-agilent, 2-transchip) OK >AT#CMODE=0 (camera m[...]

  • Page 67

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 67 of 79 13 Mounting the GE863-QUAD / PY on the Application Board 13.1 General The Telit GE863-QUAD / PY module has been designed in order to be compliant with a st andard lead-free SMT process[...]

  • Page 68

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 68 of 79 Surface finishing Ni/Au for all test pads Lead-free Alloy: Surface finishing Sn/Ag/Cu for all solder pad s[...]

  • Page 69

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 69 of 79 13.2.1 Recommended foot print for the application[...]

  • Page 70

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 70 of 79 13.2.2 Debug of the GE863 in Production To test and debug the mounting of the GE863, we strongly recommend to foreseen test pads on the host PCB, in order to check the connection betwe[...]

  • Page 71

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 71 of 79 Recommendations for PCB pad dimensions Ball pitch [mm] 2 Solder resist opening diameter A [mm] 1,150 Metal pad diameter B [mm] 1 ± 0.05 Placement of microvias not covered by solder re[...]

  • Page 72

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 72 of 79 13.2.6 GE863-QUAD / PY Solder Reflow The following is the recommended solder reflow profile[...]

  • Page 73

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 73 of 79 Profile Feature Pb-Free Assembly Average ramp-up rate (T L to T P ) 3°C/second max Preheat: – Temperature Min (Tsmin) – Temperature Max (Tsmax) – Time (min to max) (ts) 150°C 2[...]

  • Page 74

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 74 of 79 13.2.7 Packing System According to SMT processes for pick & place movement requirements, Telit GE863-QUAD / PY modules are packaged on trays, each tray contai ns 20 pieces. Tray di[...]

  • Page 75

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 75 of 79 Modules orientation on tray: Ref. Not rounded corner of module’s printed board indicates pin 1 corner. The modules in the tray are oriented as shown in A and the tray is oriented tow[...]

  • Page 76

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 76 of 79 13.2.8 Moisture Sensibility The level of moisture sensibility of Telit GE863-QUAD / PY modules is “3”, according with standard IPC/JEDEC J-STD-020, take care of all the relative re[...]

  • Page 77

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 77 of 79 14 Conformity Assessment Issues The GE863-QUAD / PY module is assessed to be conform to the R&TTE Directive as stand-alone products, so If the module is installed in conformance wi[...]

  • Page 78

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 78 of 79 15 SAFETY RECOMMANDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to [...]

  • Page 79

    GE863-QUAD GE863-PY 1vv0300715 Rev. 1 - 19/09/06 Reproduction forbidden without Telit Communications S.p.A. writte n authorization - All Right reserved page 79 of 79 16 Document Change Log R R e e v v i i s s i i o o n n D D a a t t e e C C h h a a n n g g e e s s ISSUE #0 21/02/06 First relea se ISSUE #1 19/09/06 Revie w of all the specification[...]