English dropdown-ico

Snapper Clean Sweep Twin Catcher manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Snapper Clean Sweep Twin Catcher, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Snapper Clean Sweep Twin Catcher one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Snapper Clean Sweep Twin Catcher. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Snapper Clean Sweep Twin Catcher should contain:
- informations concerning technical data of Snapper Clean Sweep Twin Catcher
- name of the manufacturer and a year of construction of the Snapper Clean Sweep Twin Catcher item
- rules of operation, control and maintenance of the Snapper Clean Sweep Twin Catcher item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Snapper Clean Sweep Twin Catcher alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Snapper Clean Sweep Twin Catcher, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Snapper service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Snapper Clean Sweep Twin Catcher.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Snapper Clean Sweep Twin Catcher item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T win Catcher Mfg. No. Description 1694498 Clean Sweep Twin Catcher 1726793 Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Clean Sweep T win Catcher[...]

  • Page 2

    1 Initial Collector Assembl y Install Cov er & Bags ......................................13 Normal Remov al & Installation Removing the Gr ass Catcher ........................14 Installing the Grass Catcher ..........................15 Hard ware Identification & T or que Specifications ....................................16 NOTE: In th[...]

  • Page 3

    2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This u[...]

  • Page 4

    BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i[...]

  • Page 5

    Initial T urbo Installation 4 50" 44" 35 49 48 7 8 6 4 5 Existing Hardware (Bolt, W asher , Lockwasher , & Nut) 40 41 42 43 22 38 44 1 1 2 3 9 18 18 15 16 17 8 14 13 Existing Pulley & Spacer T orque to 55-70 ft. lbs. 24 25 26 27 32 31 30 36 37 38 22 39 19 27 8 27 34 27 45 11 21 2 22 20 23 33 29 10 12 47 46 17 28 Existing Hardware [...]

  • Page 6

    Initial T urbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discard the cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5). 3 Slide the deflector rod (D) through the pivo[...]

  • Page 7

    Initial T urbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts. C B Figure 6. Install Deflector A. 13/64 Hole Locations[...]

  • Page 8

    Initial T urbo Installation 7 Install Idler Assembl y & Belt Co ver 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3. Mount the idler pulley assembly (A) to the deck using the two 5/16-18x 7/8 capscrews (C) and 5/16[...]

  • Page 9

    Initial T urbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C), washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on the support bracket. Different belt covers are required for different applications. Refer to Figure [...]

  • Page 10

    Initial T urbo Installation 9 Mower Dec k Arbor Pulley Mower Dec k T urbo Driv e Pulley T urbo Driv e Pulley Idler Pulleys T o Slac k en Belt CA UTION Before you begin operating the unit with the Turbo attached, be certain you have read all of the safety and operational information on the last page of this instruction sheet, as well as the Operator[...]

  • Page 11

    Initial Counter Balance & W eight Carrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier Installation A. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D. Rod B D A L F G H K I J E C M A. Rear Deck Lift Lever B. Trunnion (Existing) C. Hair Pin (Existi[...]

  • Page 12

    Initial Hitch & T ube Installation 11 Figure 1. Install Hitch Plate A. Hitch Plate E. Upper & Lower B. Heat Shield Bumper C. Capscrews, F. Washer 1/2-13 x 1-1/4 G. New Holes, 17/32” D. Locknuts, 1/2-13 H. Existing RH Holes Figure 3. Install Back Plate A. Back Plate and Support C. Hitch Plate B. Hair Pin D. Rod B A D C Figure 2. Install Hi[...]

  • Page 13

    Initial Hitch & T ube Installation 12 Figure 4. Assemble Tubes & Deflector A E C F B A. Upper Tube B. Middle Tube C. Lower Tube D. Nut, Nylock, 10-24 x 3/4 E. Washer F. Screw, Truss Head, 10-24 G. Holes H. Clip and Hardware Assemble T ubes & Deflector 1. Insert the lower tube (C, Figure 4) into middle tube (B). Secure the tubes as shown[...]

  • Page 14

    Initial Collector Assembly 13 Figure 7. Install Catcher A. Nut, #10-32 E. Hinge Pin B. Handle F. Bags C. Screw, #10-32 x 1/2 G. Hair Pin Clip D. Cover Figure 8. Install Cable A. Cable C. Washer B. Support A B C D E F G COLLECT OR ASSEMBL Y Install Cover and Ba gs 1. Hang the bags (F, Figure 7) on the horizontal sup- port. Note: If desired, the bags[...]

  • Page 15

    Normal Removal & Installation 14 NORMAL REMO V AL & INST ALLA TION Removing the Grass Catc her 1. Disconnect the tubes (A, Figure 9) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B, Figure 9) and clevis pin (D) securing the cover (E). Disconnect the cable (see Figure 8). Remove the cover (E). 3. Remove and em[...]

  • Page 16

    Removing and Reattaching Grass Catcher 15 Installing the Grass Carc her 1. Set the back plate & support (A, Figure 11) on pins of hitch plate (C). Secure with rod (D) and hair pin (B). 2. Install the bags (C, Figure 12). 3. Install the cover (E, Figure 12). Secure with the cle- vis pins (F) and hair pin clips (B). NOTE: Push the hair pin clips [...]

  • Page 17

    16 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8[...]

  • Page 18

    MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.[...]