Snapper 1691810 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Snapper 1691810, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Snapper 1691810 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Snapper 1691810. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Snapper 1691810 should contain:
- informations concerning technical data of Snapper 1691810
- name of the manufacturer and a year of construction of the Snapper 1691810 item
- rules of operation, control and maintenance of the Snapper 1691810 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Snapper 1691810 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Snapper 1691810, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Snapper service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Snapper 1691810.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Snapper 1691810 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    OPERATOR’S MANUAL 42”/48” Turbo Blower Assembly Mfg. No: 1691810 Mfg. No. 1691998 FORM 170460604 PRINTED IN U.S.A. 12/93-3ooccI[...]

  • Page 2

    HEX CAPSCREW PLAIN WASHER LOCKWASHER a p. NUT HEX CAPSCREW IDENTIFICATION Shown below are actual size hex heads for standard screw sizes. Example: a l/4” screw has a 7116 head and.thus requires a 7716 wrench. To measure length, use the scale below. ~0000 t/2” Heed 7fl6” Head 34” Head 518” Head 6716” Head screw with screw with screw with[...]

  • Page 3

    Table of Contents Safety Decal ................................ Safety Rules ................................ Installation Lawn Tractor ........................... Front-Cut Rider ......................... Operation .................................. Standard Fastener Identification Chart ....... ....... ....... ....... ....... ....... ....... ....[...]

  • Page 4

    Safety Rules A Read these safety rulesand the safety rules in yo,ur Operator’s Manual and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. The triangle in the text signifies important cautions or warnings which must be followed. A W[...]

  • Page 5

    installation - Lawn ,Tractors NOTE Two spacers are packaged with turbo biower. Installation on tractor requires use of 4-l/16” spacer (see step 11); the 1/2”spacerwill not be used. 1. Remove mower deflector and arbor cover as follows: a. Remove the mower deflector by removing two carriage bolts, lockwashers and nuts. Install this hardware on th[...]

  • Page 6

    NOTE Front belt stop should be installed facing outside of deck. ‘6. Install thefront belt stop (A, figure4) onto5/16- 18 x l-1/2 capscrew (installed in step 3) as shown. If removed, reinstall brake spring or spring anchor (F) before flange nut(G). Tighten nut (E) snug only - belt stop will be adjusted in step 8. G Mower Decks Figure 4. a Belt st[...]

  • Page 7

    10. The baffle (A, figure 7) is installed in the blower housing for use with 42” mower. For use with 48” mower, remove the baffleand install in holes marked 48”. I Figure 7. A Battle NOTE On42”and 48” mowersthecapscrewinstalled in next step is used in the hole occupied by a screw held in place by a retaining nut. (This screw secured the r[...]

  • Page 8

    12. Install wing nut (D, figure 9) as follows: a. Remove existing hardware from front end of stone guard. b. From inside deck, install new 5/16-18 x 2-l/4 carriage bolt (F, figure 9). Then install the cup (A), 5/16 lockwasher (6). and 506 nut (C). Tighten the nut. c. Thread the wing nut (D) far enough onto the screw so that the 5/16 locknut (E) can[...]

  • Page 9

    c. Place mower in low cut position. Raise the flap (A, figure 12) and push on the belt retainer (E) to obtain slack in the belt. Install the blower drive belt (D) in the top groove of the pulley(B). d. Rotate the pivoting cover (A, figure 13) into place and attach the hook (B) to the clip (C) on the housing. Figure 12 A. Flap 6. Pulley c. Ben D. [...]

  • Page 10

    Installation - Front Cut Riders NOTES 1. Two spacers are packaged with the turbo blower. Installation on the Front-Cut Rider requires use of the l/2” spacer (see step 14). The 4-l/16” spacer will not be used. 2. The replacement right hand belt cover (seestep 15),along with thenew3/8-16x2-1M”capscrew for the right hand idler pulley (see step 4[...]

  • Page 11

    6. Remove the capscrew, lockwasher, and flat washer securing right hand arbor pulley. Retain the washers for reinstallation (step 9). Use a wood block to prevent blade from turning. SunRunnerNanguard Models 6. On early models without bet stop (A, figure 3) remove two self-tapping screws from arbor and install two .5/l 6-18 x l-1/2” capscrews (A, [...]

  • Page 12

    9. Slip the mower drive belt (A, figure 5) around the bottom groove of double-groove pulley (B). Install pulley with hub down and secure with new 7/l 6-14 x 2-l /4” capscrew (C) and washers (D and E) removed in step 5. Make sure splines arecorrectlyalignedand torquecapscrewto55- 60 ft. Ibs. Use a wood block to prevent the blade from turning. 10. [...]

  • Page 13

    13. Install the new baffle (A, figure 8) in deck on stone guard using existing hardware. Hardware may be installed with nut to inside or nut to outside. 14. On new arbor cover, install on top of weld bolt (A, figure 9) the largest washer (B l-i/Z” O.D.), l/2’ spacer (C), lo&washer(D), and nut (Q as shown in figures. (Largeflatwasher(F) show[...]

  • Page 14

    16. Make sure that flat washer (F, figure 9) is on top of spacer assembly and install new arbor belt cover (A, figure 10) as shown in figure 10. Secure with flat washer (l-1/4” O.D.) and locknut (8). Belt cover should be free to pivot. 17. Install the blower assembly as follows: a. Align th& notch on blower assembly with spacer on arbor brack[...]

  • Page 15

    Operation A WARNING For safety reasons, grass and debris should not be removed from any part of turbo or collection system until engine is shut off, key removed, and all moving parts have stopped. I A I WARNING Before raising cart or twin-bag cover, shut off engine, remove key, and set parking brake. BEFORE OPERATION Clear the lawn of all sticks, s[...]

  • Page 16

    [...]

  • Page 17

    i[...]

  • Page 18

    .:::).‘,:,:::: ~._,, ,[...]

  • Page 19

    ..:,, ::: TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +200/o SIZE 8-32 8-36 lo-24 lo-32 l/4-20 l/4-28 5116-18 5116-24 318-16 318-24 7116-14 7116-20 l/2-13 112-20 9116-12 9116-18 518-11 518-18 314-10 3/4-16 718-g 718-14 1-8 1-12 SAE GRADE #2 SAE GRADE A15 SAE GRADE #8 0 Q 8. InJLbs. In./Lbs. InAbs. Ft.lLbs. Nm. Ft./Lb.s. Nm. Ft.Rbs[...]