Smeg PGA95F3 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Smeg PGA95F3, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Smeg PGA95F3 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Smeg PGA95F3. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Smeg PGA95F3 should contain:
- informations concerning technical data of Smeg PGA95F3
- name of the manufacturer and a year of construction of the Smeg PGA95F3 item
- rules of operation, control and maintenance of the Smeg PGA95F3 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Smeg PGA95F3 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Smeg PGA95F3, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Smeg service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Smeg PGA95F3.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Smeg PGA95F3 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE ________________ 4 2. INSTALLATION OF THE APPLIANCE _________________________ 6 3. GAS CONNECTION ______________________________________ 12 4. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 14 5. FINAL OPERATIONS _____________________________________ 16 6. USE OF THE COOKING HOB _______________[...]

  • Page 2

    Instructions for the installer 4 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN A N ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE C O OKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE [...]

  • Page 3

    Instructions for the installer 5 DO NOT PUT PANS WITHOUT PERFECTLY S MOOTH AND FLAT BOTTOMS ON THE COOKI NG HOB GRIDS. DO NOT USE RECIPIENTS OR G RIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF THE HOB. THE HOB IS TO BE USED BY ADULTS ON LY . DO NOT LET UNSUPERVISED CHILDREN PLAY WITH THE HOB. REPLACED APPLIANCES MUST BE TAKEN TO A SPECI[...]

  • Page 4

    Instructions for the installer 6 2. INST ALLA TION OF THE APPLIANCE The following operation r equires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 2.1 Fixi[...]

  • Page 5

    Instructions for the installer 7 2.2 Attachment to support struct ure, flush-mounting model Create an opening w ith the dimensions shown in the figure in the work surface, observing a minimum distanc e of 50 mm from the rear edge. The lower part of the protective cover must be fully accessible when the appliance is installe d. This appliance can be[...]

  • Page 6

    Instructions for the installer 8 Overall dimensions: location of gas and electrical connection poi nts (all measures in mm). Caution: surface temperature under neath may exceed 125 degrees C. To avoid a hazard, under-bench access must be restricted. Refer to installation instruction IMPORTANT: when installing the ap pliance above a cupboard, a divi[...]

  • Page 7

    Instructions for the installer 9 2.3 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measureme nt A ) Range hoods and exha ust fans shall be installed in accor dance with the manufacturer’s instructions. Howev er, in no case shall the clearance between the highest part of the hob of the c[...]

  • Page 8

    Instructions for the installer 10 2 Side clearances – (Measurements B & C) Where B , mea sured from the periphery of the nearest burner to any vertical combu stible surface , is less than 200 mm , the surface shall be protected in accorda nce with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for th e full dimension (wid[...]

  • Page 9

    Instructions for the installer 11 2.5 Discharge of combustion products Discharge of combustion pr oducts mu st be guaranteed by means of hoods connected to a natur al draught fl ue with certain efficiency, or by means of forced aspiration. An efficient aspiration system requir es careful planning by a specialist capable of insta lling it, respectin[...]

  • Page 10

    Instructions for the installer 12 3. GAS CONNECTION This appliance is su itable for installation with Natural Gas or ULPG (propane). R efer to page 12 for the relevant burner press ure and appropriate injector sizes. When the ap pliance is to be connected to Natural Gas then the pressure regulator supp lied must be fitted to the gas inlet. A te st [...]

  • Page 11

    Instructions for the installer 13 3.1 Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical syst[...]

  • Page 12

    Instructions for the installer 14 4. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenanc e work, detach th e appliance from the electrical socket. The hob of the cooker is ad justed for use wi th either natural gas at a pressure of 1.0 kPa . If used with other types of gas, you have to replace the nozzles, then ad [...]

  • Page 13

    Instructions for the installer 15 4.2 Burner and nozzle characteristic s table Burner ULPG – 2.75 kPa Nominal gas consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.54 Semi rapid (2) 6.3 0.68 WOK (4) 13.5 1.00 Burner NG – 1.0 kPa Nominal gas consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.90 Semi rapid (2) 7.5 1.20 WOK (4) 15 1.75 4.3 Ar[...]

  • Page 14

    Instructions for the installer 16 5. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the i nstructions in paragraph “4.2 Burner and nozzle characteristics table”. After adjustment to a different kind of gas from the one for which the cooker has been tested, replac e the plate inside t[...]

  • Page 15

    Instructions for the user 6. USE OF THE COOKING HOB 6.1 Lighting the burners Before lighting the hob burners che ck that the flame caps are in th e correct position and that their burner caps are in place, making sure th a t the holes A in the flame caps correspon d to the spark plugs an d thermocouples. Panstand grid B, available upon r equest, is[...]

  • Page 16

    Instructions for the user 18 6.2 Practical advice for usin g the burners For better use of the burners and lower gas consumption, use covered containers that are proportion al in size to the burner to prevent the flame from licking the sides (see para graph “ 6.3 Diameter of containers ”). When water reaches the boiling point, lower the fl ame [...]

  • Page 17

    Instructions for the user 7. CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 7.1 Cleaning stainless steel To keep stainless steel in good cond ition it should be cleaned regularl y after use. Let it cool first. 7.1.1 Ordinary Daily Cleaning To clean and preserve the stainl ess steel surfaces, always use [...]

  • Page 18

    Instructions for the user 20 7.3 Preventive maintenance This appliance does not nee d any special maintenance. However, a few simple operations have to be c arried out periodically to prevent malfunctioning: Burners: the burners must be cleaned periodically to en sure correct combustion; make sure that a ll t he openings and flame ports are clean a[...]

  • Page 19

    [...]

  • Page 20

    914772758/ C[...]