English dropdown-ico

Sanyo LNS-S03 manual

1
2
3
4
5
6
7
8
9
10

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Sanyo LNS-S03, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Sanyo LNS-S03 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Sanyo LNS-S03. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Sanyo LNS-S03 should contain:
- informations concerning technical data of Sanyo LNS-S03
- name of the manufacturer and a year of construction of the Sanyo LNS-S03 item
- rules of operation, control and maintenance of the Sanyo LNS-S03 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Sanyo LNS-S03 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Sanyo LNS-S03, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Sanyo service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Sanyo LNS-S03.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Sanyo LNS-S03 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    T ype of the Cabinet (1) See P age 2 LCD PR OJECT OR LENS MODEL NO . LNS-S03 LENS REPLA CEMENT AND INST ALLA TION PR OCEDURES NO TES ON REPLA CEMENT AND INST ALLA TION The procedures and the needed pars f or lens installation depend on the type of cabinet. Bef ore installing or replacing the lens, make sure the type of cabinet and be sure to ref er[...]

  • Page 2

    Some par ts are not used f or installation or replacement. K eep these par ts f or later use. Note : Figures in this manual ma y be diff er from the actual product. NO TES ON LENS INST ALLA TION • Lens installation and replacement should be made by the qualified service per- sonnel. • Be sure to install the lens f ollowing this procedure precis[...]

  • Page 3

    LENS REPLA CEMENT AND INST ALLA TION PROCEDURE {T ype (1) Cabinet} -2- 1 Remove Lower Lens Cover. Remove 2 Screws A. Push part B and pull Lower Lens Cover down. (See Fig. 1.) 2 Remove 4 Screws C. Pull Upper Lens Cover toward front and remove. (See Fig. 2.) 3 Remove 2 Scres D and Cover Plate on the back of Upper Lens Cover. (See Fig. 3.) A C C B Fig[...]

  • Page 4

    5 Connect Lens Motor Lead to the connector "K96T" on the circuit board under the lens. 4 Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens Mouting Bracket with 4 Screws. To mount the lens with Lens Motor on the right. (See Fig. 4.) GUIDE PIN Fig-4 DRIVER IN THE LENS LOCATE MOTOR ON RIGHT SIDE LENS [...]

  • Page 5

    Fig-6 LIGHT BLOCK SHEET Make sure the sheet figure and put on proper position. -4- 6 Use a Light-Block Sheet (provided with projector) corresponding with lens. (Refer to the Type No. below.) Set Light-Block Sheet through the lens. Make sure the shape of Light-Block Sheet and be sure to set them as shown in the Fig. 6. NOTE: ● Be sure to set a Lig[...]

  • Page 6

    -5- 7 Replace Upper Lens Cover. Slide Light-Block Sheet into the guide of Upper Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 4 Screws C. (See Fig. 2.) 8 Replace Lower Lens Cover. Slide Light-Block Sheet into the guide of Lower Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover w[...]

  • Page 7

    LENS REPLA CEMENT AND INST ALLA TION PROCEDURE {T ype (2) Cabinet} -6- 1 Remove Lens Cover. Remove 2 Screws A. Push part B and pull Upper Lens Cover up. (See Fig. 1.) 2 Remove 4 Screws C. Pull Lower Lens Cover toward front and remove. (See Fig. 2.) 3 Remove 2 Screws D and Cover Plate on the back of Upper Lens Cover. (See Fig. 3.) Fig-1 UPPER LENS C[...]

  • Page 8

    -7- 5 Connect Lens Motor Lead to the connector "K96T" on the circuit board under the lens. Fix Lens Motor Lead with the lead holder on the cir- cuit board. Fig-5 LEAD HOLDER K96T CONNECTOR Fig-4 LENS MOTOR LEAD LENS MOUNTING BLACKET GUIDE PIN 4 Replace Lens Cap on the rear (mounting side) of Projection Lens and mount the lens on Lens Mout[...]

  • Page 9

    6 Use 2 Light-Block Sheets (provided with projector) corresponding with lens. (Refer to the Type No. below.) Set 2 Light-Block Sheets through the lens. Make sure the shape of Light-Block Sheets and be sure to set them as shown in the Fig. 6. Fig-6 LIGHT BLOCK SHEETS Make sure the sheets figure and put on proper position. -8- NOTE: ● Be sure to se[...]

  • Page 10

    -9- 7 Replace Lower Lens Cover. Slide Light-Block Sheets into the guide of Lower Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 4 Screws C. (See Fig. 2.) 8 Replace Upper Lens Cover. Slide Light-Block Sheets into the guide of Upper Lens Cover and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover[...]