English dropdown-ico

Q-Logic 2300 series manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Q-Logic 2300 series, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Q-Logic 2300 series one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Q-Logic 2300 series. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Q-Logic 2300 series should contain:
- informations concerning technical data of Q-Logic 2300 series
- name of the manufacturer and a year of construction of the Q-Logic 2300 series item
- rules of operation, control and maintenance of the Q-Logic 2300 series item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Q-Logic 2300 series alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Q-Logic 2300 series, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Q-Logic service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Q-Logic 2300 series.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Q-Logic 2300 series item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    CF2351102-00 F Page i Q Simplify SANblade 2300 Series User ’ s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters[...]

  • Page 2

    SANblade 2300 Series User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters Q Page ii CF2351102-00 F Information fu rnished in this manual is believed to be accurate and reliab le. However , QLogic Corporation assumes no responsibility for its use, nor for any infringements of patent s or other rights of third part ies which may resul[...]

  • Page 3

    CF2351102-00 F Page iii Table of Contents Section 1 Introduction 1.1 How to Use this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.3 What is Fibre Channel? . . . . . . . . . . . . . . . . . . . . [...]

  • Page 4

    SANblade 2300 User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters Page iv CF2351102-00 F Q 3.3 Removing the QCP2340/2342 HBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 3.4 FCode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 3.4.1 Updating FCode on the [...]

  • Page 5

    CF2351102-00 F Page v Q SANblade 2300 User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Ad apters Part II Software Section 6 Solaris SPARC Driver Installation 6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 6.2 Pre-installation Requirements . . . . . . . . . . . . . . . [...]

  • Page 6

    SANblade 2300 User’s Guide 2-Gb Fibre Channel to cPCI and SBus Host Bus Adapters Page vi CF2351102-00 F Q Notes[...]

  • Page 7

    CF2351102-00 F 1-1 Section 1 Introduction 1.1 How to Use this Guide The SANblade QLogic host bus a dapters (HBAs) supported in this document are described in the following p aragraphs. They are collectively referred to as the QCP/QSB23xx HBA unless otherwise noted. The QCP23 xx HBAs are all 64-bit PCI to Fibre Channel optical media. The QS B23xx HB[...]

  • Page 8

    1 – Introduction Features 1-2 CF2351102-00 F Q interface for intermediate dist ances (less than 500 meters at the data ra te of 1 Gbps; less than 300 meters at the dat a rate of 2 Gbps). With increased connectivity and performanc e, Fib re Channel is the technology preferred and used by system designers. 1.4 Features ■ Compliance with the follo[...]

  • Page 9

    CF2351102-00 F I-1 Part I Hardware This part of the SANblade 2300 User ’s Guide describes the host bus a dapters (HBAs) and how to install and configure them. See the section that co rresponds to your HBA. Section 5 contains troubleshoot ing information. HBA Section QCP2330/2332 2 QCP2340/2342 3 QSB2340/2342 4[...]

  • Page 10

    I – Hardwa re I-2 CF2351102-00 F Q Notes[...]

  • Page 11

    CF2351102-00 F 2-1 Section 2 QCP2330/2332 2.1 QCP2330/2332 HBA Component s Figure 2-1 identifies the QCP2330/2332 HBA compo nents referenced throughout this section. Each QCP2330/2332 HBA has a unique serial number , located on the back of the HBA. T ake a minute to write down th e serial number of the QCP2330/2332 HBA in the unlikely event that th[...]

  • Page 12

    2 – QCP2330/2332 Installation and Removal 2-2 CF2351102-00 F Q 2.1.2 Jumpers Jumpers J1 (QCP2332) and J2 on the QCP2330/2332 HBA determine the defau lt state of connectors J5 (QCP2332) an d J6, respectively . The jumpers are set at the factory with a jumper plug on pins 2–3, which enables the connectors. CAUTION! Changing the jumper settings ca[...]

  • Page 13

    2 – QCP2330/2332 Installation and Removal CF2351102-00 F 2-3 Q 2.2.2 Inst allation in the Computer (Hot Swap) Perform the following steps to inst all the QCP2330/2332 HBA without shutting down the system (hot swap). See section 2.2.1 for st andard installation instruct ions. 1. Log on to the system as a superuser . 2. At the prompt (#), type the [...]

  • Page 14

    2 – QCP2330/2332 Installation and Removal 2-4 CF2351102-00 F Q 4. T ype the cfg adm command (see step 2 ) to verify that the system recognizes the QCP2330/2332 HBA and that the HBA is not configured. In the following example, the QCP2330/2332 HBA h as been installed in slot 4 and is not configured. 5. T ype the following commands to configure the[...]

  • Page 15

    2 – QCP2330/2332 FCode CF2351102-00 F 2-5 Q 6. Connect the appropriate cables from the devices to the J5 (QCP2332) and J6 connectors. 7. Check the QCP2330/2332 HBA hot swap LED1; it should be off , indicating that the HBA is active. See section 6 for detailed instructions on how to install the sof tware driver . If you need FCode, see section 2.4[...]

  • Page 16

    2 – QCP2330/2332 FCode 2-6 CF2351102-00 F Q 3. Set the QCP2330/2332 HBA loop ID (see sect ion 2.4.3) . 4. Select the boot device (see section 2.4.4) . 5. Build the bootable disk (see section 2.4.5) . 2.4.1 Up dating FCode on the QCP2330/2332 HBA If you need to update the FCode on th e QCP2330/2332 HBA, use the QLogic qla2x00 flash utility . A QLo[...]

  • Page 17

    2 – QCP2330/2332 FCode CF2351102-00 F 2-7 Q The new connection mode displays. F or example: Calculating NVRAM checksum, please wait... Current HBA connection mode: 0 - Loop Only Possible connection mode choices: 0 - Loop Only 1 - Point-to-point only 2 - Loop preferred, otherwise point-to-point 2.4.3 Setting the QCP2330/2332 HBA Loop ID When the Q[...]

  • Page 18

    2 – QCP2330/2332 FCode 2-8 CF2351102-00 F Q 2. Select the QCP2330/2332 HBA att ached to the Fibre Channel device from which you want to boot. For example, type the following at the ok prompt: ok " /pci@1f,0/pci@1/QLGC,qla@4" select-dev 3. Use the show-children co mmand to view the devices attached to the QCP2330/2332 HBA. For example: o[...]

  • Page 19

    2 – QCP2330/2332 FCode CF2351102-00 F 2-9 Q T o build a boot able disk, perform the following steps: 1. Determine the amount of disk space us ed/available on your current boot disk. Use the df command for a listing. For example: /usr/bin/df -k -l This df example shows that the current boot disk is /dev/dsk/c0t0d0s(x). There are two partitions of [...]

  • Page 20

    2 – QCP2330/2332 FCode 2-10 CF2351102-00 F Q d. At the partition prompt, t ype print . The partition t able displays, as in the following example. e. At the partition prompt, t ype label . Enter the label. f. At the label prompt, type q uit . g. T ype quit until the system prompt displays. 3. T o create the file system, use the newfs command. For[...]

  • Page 21

    2 – QCP2330/2332 FCode CF2351102-00 F 2-11 Q 10. Shut down the system. T ype the following: /sbin/init 0 1 1. Boot from the newly created boot disk. For example: boot /pci@1f,0/pci@1/QLGC,qla@4/sd@82,0 NOTE: The target device ID ( sd@82 ) is in hexadecimal. The decimal value is used in step 3 . 12. V iew the current dump device setting. For examp[...]

  • Page 22

    2 – QCP2330/2332 Specifications 2-12 CF2351102-00 F Q T able 2-1 lists t he values to enter and their corresponding dat a rates. 2.5 S pecifications T ables 2-2 and 2-3 define the QCP2330/2332 specifications. T able 2-1. Fibre Channel Data Rates Va l u e Data Rate 0 One gigabit 1 T wo gigabit s 2 Auto-negotiated rate T able 2-2. QCP2330/2332 Boar[...]

  • Page 23

    2 – QCP2330/2332 Agency Certification CF2351102-00 F 2-13 Q 2.6 Label The transceiver on the QCP2330/2 332 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.1 1. The transceiver must be operated under recommended op erating conditions. 2.7 Agency Certification The following sections cont ain a summary of E[...]

  • Page 24

    2 – QCP2330/2332 Agency Certification 2-14 CF2351102-00 F Q ❑ EN61000-3-2:1995 Harmonic Current Emission ❑ EN61000-3-3:1994 V olt age Fluctuation and Flicker ■ VCCI, Class A ■ AS/NZS 3548, Class A C-tick 2.7.2 Product Safety Requirement s ■ UL, cUL ❑ UL 6095050 ❑ CSA C22.2 No 60950 ❑ Class 1 Laser Product per DHHS 21CFR (J) ■ 73[...]

  • Page 25

    CF2351102-00 F 3-1 Section 3 QCP2340/2342 3.1 QCP2340/2342 HBA Component s Figure 3-1 identifies the QCP2340/2342 HBA compo nents referenced throughout this section. Each QCP2340/2342 HBA has a unique serial number , located on the back of the HBA. T ake a minute to write down th e serial number of the QCP2340/2342 HBA in the unlikely event that th[...]

  • Page 26

    3 – QCP2340/2342 Installation and Removal 3-2 CF2351102-00 F Q 3.1.1 LEDs The QCP2340/2342 LED1 and L ED2 (QCP2342) function as shown in tabl e 3-1 . In a standa rd installation, LED3 is of f, i ndicating that the HBA is active. In a hot swap installa tion, LED3 turns blue while the HBA is inserted. If the LED turns o ff, the HBA is inserted and [...]

  • Page 27

    3 – QCP2340/2342 Installation and Removal CF2351102-00 F 3-3 Q 3. Place the QCP2340/2342 HBA into th e slot. Carefully press the HBA into the slot until it seat s firmly (the switch clicks into a locked position when the HBA is seated). 4. Connect the appropriate cables from the devices to the J2 (QCP2342) and J1 connectors. 5. Power up all exter[...]

  • Page 28

    3 – QCP2340/2342 Installation and Removal 3-4 CF2351102-00 F Q A list of the system’ s processors, memory , and I/O boats appears, as in the following example. In this example, cP CI slot s 0, 1, 3, and 4 are available. NOTE: If the cPCI slots are not d isplayed, add the following line to the etc/system file: set sghsc:cpci_enable=1 Check the i[...]

  • Page 29

    3 – QCP2340/2342 Installation and Removal CF2351102-00 F 3-5 Q 4. T ype the cfg adm command (see step 2 ) to verify that the system recognizes the QCP2340/2342 HBA and that the HBA is not configured. In the following example, the QCP2340/2342 HBA h as been installed in slot 4 and is not configured. 5. T ype the following commands to configure the[...]

  • Page 30

    3 – QCP2340/2342 Removing the QCP2340/2342 HBA 3-6 CF2351102-00 F Q 6. Connect the appropriate cables from the devices to the J2 (QCP2342) and J1 connectors. 7. Check the QCP2340/2342 HBA hot swap LED3; it should be off , indicating that the HBA is active. See section 6 for detailed instructions on how to install the sof tware driver . If you nee[...]

  • Page 31

    3 – QCP2340/2342 FCode CF2351102-00 F 3-7 Q 3. Set the QCP2340/2342 HBA loop ID (see sect ion 3.4.3) . 4. Select the boot device (see section 3.4.4) . 5. Build the bootable disk (see section 3.4.5) . The QCP2340 has one channel; the QC P2342 has two channels. The code distinguishes between t he channels as follows: ■ qla@4 (QCP2340 and QCP2342 [...]

  • Page 32

    3 – QCP2340/2342 FCode 3-8 CF2351102-00 F Q The connection mode and options displa y . For example: Current HBA connection mode: 2 - Point-to-point only Possible connection mode choices: 0 - Loop Only 1 - Point-to-point only 2 - Loop preferred, otherwise point-to-point 2. If the connection mode is not correct based on the devices connected to the[...]

  • Page 33

    3 – QCP2340/2342 FCode CF2351102-00 F 3-9 Q 3.4.4 Selecting the Boot Device Perform the following step s to select a Fibre Channel device that is at tached to the QCP2340/2342 HBA as the boot device : 1. Use the show-devs command to display the device tree for all devices attached to the machine. ok show-devs The device tree displays. The QCP2340[...]

  • Page 34

    3 – QCP2340/2342 FCode 3-10 CF2351102-00 F Q 3.4.5 Building the Boot able Disk This procedure assumes that the system is already booted from an existing system hard disk, and that you have alre ady performed a full system backup. The device path on ea ch system differs, depending on the PCI bus slot, t arget ID, LUN, etc. The device name shown in[...]

  • Page 35

    3 – QCP2340/2342 FCode CF2351102-00 F 3-11 Q a. At the root prompt, type format . b. A list of available hard di sks displays. S pecify th e disk. c. At the format prompt, type partition . d. At the partition prompt, t ype print . The partition t able displays, as in the following example. e. At the partition prompt, t ype label . Enter the label[...]

  • Page 36

    3 – QCP2340/2342 FCode 3-12 CF2351102-00 F Q 9. Edit the new vfstab file to properly mount the new partition s during boot. In this case, each reference to c0t0 d0s0 is changed to c3t130d0s0. For example: vi /mnt/etc/vfstab 10. Shut down the system. T ype the following: /sbin/init 0 1 1. Boot from the newly created boot disk. For example: boot /p[...]

  • Page 37

    3 – QCP2340/2342 Specifications CF2351102-00 F 3-13 Q 3.4.6 Setting and Viewing the Fi bre Channel Dat a Rate Use the show-dat a-rate command to view the current QCP2340/234 2 Fibre Channel data rate. For example: ok show-data-rate Current HBA data rate: One Gigabit rate Use the set-data-rat e command to change the current QCP2340/2342 Fibre Chan[...]

  • Page 38

    3 – QCP2340/2342 Label 3-14 CF2351102-00 F Q 3.6 Label The transceiver on the QCP2340/2 342 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.1 1. The transceiver must be operated under recommended op erating conditions. 3.7 Agency Certification The following sections cont ain a summar y of the EMC/EMI tes[...]

  • Page 39

    3 – QCP2340/2342 Agency Certification CF2351102-00 F 3-15 Q ❑ EN55022:1995 Class A ❑ Radiated Emission Class A ❑ Conducted Emission Class A ❑ EN55024:1998 ❑ Immunity S t andards ❑ EN61000-4-2 :1995 ESD ❑ EN61000-4-3 :1995 RF Electro Magnetic Field ❑ EN61000-4-4 :1995 Fast T ransient/Burst ❑ EN61000-4-5 :1995 Fast Surge Co mmon/D[...]

  • Page 40

    3 – QCP2340/2342 Agency Certification 3-16 CF2351102-00 F Q Notes[...]

  • Page 41

    CF2351102-00 F 4-1 Section 4 QSB2340/2342 4.1 QSB2340/2342 HBA Component s Figure 4-1 identifies the QSB2340/234 2 HBA components referenced throughout this section. Each QSB2340/2342 HBA has a u nique serial number , located on the back of the HBA. T ake a minute to write down the se rial number o f the QSB2340/2342 HBA in the unlikely event that [...]

  • Page 42

    4 – QSB2340/2342 Installation in the Computer 4-2 CF2351102-00 F Q 4.1.1 LEDs The QSB2340/2342 LED1 and LED2 (QSB2342) function as shown in table 4-1 . 4.1.2 Jumpers Jumpers J7 (QSB2342) and J8 on the QSB2340 /2342 HBA determine the default state of connectors J10 (QSB2342) and J9, respectively . The jumpers are set at the factory with a jumper p[...]

  • Page 43

    4 – QSB2340/2342 FCode CF2351102-00 F 4-3 Q See section 6 for detailed instructions on how to install the sof tware driver . If you need FCode, see section 4.3 for instructions on how to inst all or update the FCode on the QSB2340/2342 HBA. 4.3 FCode This section provides instructions fo r installing FCode on a QSB2340/2342 HBA installed in a Sol[...]

  • Page 44

    4 – QSB2340/2342 FCode 4-4 CF2351102-00 F Q 4.3.2 Setting the QSB2340/2342 HBA Connection Mode Perform the following step s to view the current QSB2340/2342 HBA connection mode and change it if necessa ry: 1. Perform step s 1 and 2 in section 4.3.4 . 2. T o view the current connection mode, type the show-connection-mode command. ok show-connectio[...]

  • Page 45

    4 – QSB2340/2342 FCode CF2351102-00 F 4-5 Q 3. If the loop ID is not correct, chang e it using the set-adapter-loopid command. For example: ok 0 set-adapter-loopid The new loop ID displays. For example: Adapter loopid - 0 4.3.4 Selecting the Boot Device Perform the following step s to select a Fibre Channel device that is at tached to the QSB2340[...]

  • Page 46

    4 – QSB2340/2342 FCode 4-6 CF2351102-00 F Q 5. Save the boot device information to the QSB2340/2342 HBA ’s NVRAM. Use the set-boot-id command. Include the selected QSB2340/2342 HBA ’s WWN, loop ID, and LUN. For example: ok 2200002037009eeb 82 0 set-boot-id The following displays: Calculating NVRAM checksum, please wait.... done Boot device lo[...]

  • Page 47

    4 – QSB2340/2342 FCode CF2351102-00 F 4-7 Q T o build a boot able disk, perform the following steps: 1. Determine the amount of disk space us ed/available on your current boot disk. Use the df command for a listing. For example: /usr/bin/df -k -l This df example shows that the current boot disk is /dev/dsk/c0t0d0s(x). There are two partitions of [...]

  • Page 48

    4 – QSB2340/2342 FCode 4-8 CF2351102-00 F Q a. At the root prompt, type format . b. A list of available hard di sks displays. S pecify th e disk. c. At the format prompt, type partition . d. At the partition prompt, t ype print . The partition t able displays, as in the following example. e. At the partition prompt, t ype label . Enter the label.[...]

  • Page 49

    4 – QSB2340/2342 Specifications CF2351102-00 F 4-9 Q 9. Edit the new vfstab file to properly mount the new partition s during boot. In this case, each reference to c0t0 d0s0 is changed to c3t130d0s0. For example: vi /mnt/etc/vfstab 10. Shut down the system. T y pe the following: /sbin/init 0 1 1. Boot from the newly created boot disk. For example[...]

  • Page 50

    4 – QSB2340/2342 Label 4-10 CF2351102-00 F Q 4.5 Label The transceiver on the QSB2340/2342 HBA is a Class I laser product. It complies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.1 1. The transceiver must be operated under recommended op erating conditions. 4.6 Agency Certification The following sections cont ain a summar y of the EMC/EMI test[...]

  • Page 51

    4 – QSB2340/2342 Agency Certification CF2351102-00 F 4-11 Q ❑ EN61000-4-5 :1995 Fast Surge Co mmon/Differential ❑ EN61000-4-6 :1996 RF Conducted Susceptibility ❑ EN61000-4-8 : 1993 Power Frequency Magnetic Filed ❑ EN61000-4-1 1: 1994 V olt age Dips and Interrupt ❑ EN61000-3-2:1995 Harmonic Current Emission ❑ EN61000-3-3:1995 V olt age[...]

  • Page 52

    4 – QSB2340/2342 Agency Certification 4-12 CF2351102-00 F Q Notes[...]

  • Page 53

    CF2351102-00 F 5-1 Section 5 T roubleshooting 5.1 Problems Af ter Inst allation There are two basic types of inst allation problems that can cause your QCP/QSB23 xx HBA to function incorrectly: hardware problems and Fibre Channel problems. The following section provides it emized checklist s to help you determine why your QCP/QSB23 xx HBA is not fu[...]

  • Page 54

    5 – Troubles hooting Fibre Channel Problem Checklist 5-2 CF2351102-00 F Q Notes[...]

  • Page 55

    CF2351102-00 F II-1 Part II Sof t ware This part of the SANblade 2300 User’s Guide describes how to inst all the software drivers for the supported operating systems. See t he section that corresponds to your computer ’s operating system: Before you insta ll the software drivers, you need to locate an d download the appropriate drivers for your[...]

  • Page 56

    II – Software II-2 CF2351102-00 F Q Notes[...]

  • Page 57

    CF2351102-00 F 6-1 Section 6 Solaris SP ARC Driver Inst allation (QL2300) 6.1 Introduction This section provides instructions for in stalling the Solaris SP ARC driver in an already installed So laris SP ARC operating system. The naming convention for the drivers, associated files, and messages is QLA; however , the Solaris SP ARC driver supports s[...]

  • Page 58

    6 – Solaris SPARC Driver Installation Installing the Solaris SPARC Driver from a CD-ROM 6-2 CF2351102-00 F Q qla2300 driver versions 4.1 1 (and earlier) have the following p ackage names: ❑ QLA2300-1 (Solaris 2.6) ❑ QLA2300-2 (Solaris 2.7) ❑ QLA2300-3 (Solaris 2.8 and 9) Checks within the packag e installation will terminate the new driver [...]

  • Page 59

    6 – Solaris SPARC Driver Installation Installing the Solaris SPARC Dr iver from the QLogic Web Site CF2351102-00 F 6-3 Q 1. Log on to the system as a superuser . 2. Download the driver p ackage from the QLogic W eb site ( www .qlogic.com ) to a directory on the Solaris machine’ s hard disk. 3. At the command prompt, change the directory (cd) to[...]

  • Page 60

    6 – Solaris SPARC Driver Installation Installing the Solaris SPARC Driv er from the QLogic Web Site 6-4 CF2351102-00 F Q 9. Y ou are prompted to select the directory whe re the driver will be installed. For example: Processing package instance <QLA2300> from </tmpdir/qla2300_pkg> QLogic QLA2300 driver (sparc) Solaris, Rev=X.XX Copyrig[...]

  • Page 61

    6 – Solaris SPARC Driver Installation FCode CF2351102-00 F 6-5 Q 13. The pkga dd program then installs the SDM library , if selected in step 8 . A script warning is posted, asking whether to continue the in stallation. For example: Processing package instance <QLSDMLIB> from </tmpdir/qla2300_pkg> QLogic SDM Library (sparc) Solaris 7-8[...]

  • Page 62

    6 – Solaris SPARC Driver Installation FCode 6-6 CF2351102-00 F Q Notes[...]