English dropdown-ico

Pelco VS5008 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco VS5008, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco VS5008 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco VS5008. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco VS5008 should contain:
- informations concerning technical data of Pelco VS5008
- name of the manufacturer and a year of construction of the Pelco VS5008 item
- rules of operation, control and maintenance of the Pelco VS5008 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco VS5008 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco VS5008, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco VS5008.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco VS5008 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    ® VS5004/VS5008 Sequential Switcher INSTALLATION/OPERATION C808M-G (4/05)[...]

  • Page 2

    2 C808M-G (4/05) Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

  • Page 3

    C808M-G (4/05) 3 Description The VS5004 and VS5008 sequential switchers are designed to switch up to four (VS5004) or eight (VS5008) cameras manually or automatically to one or two monitors with automatic response to alarm inputs. Both versions are Coaxitron ® compatible and can be placed on a desktop or rack mounted. MODELS VS5004 Sequential swit[...]

  • Page 4

    4 C808M-G (4/05) Installation T ERMINATED CAMERA INPUTS AND ONE MONITOR OUTPUT 1. Make all equipment connections. Refer to Figure 1 (VS5004) or Figure 2 (VS5008). VS5008 only: When configured for one-monitor operation, the monitor must be connected to the MON 2 output. The MON 1 output must be terminated with a 75-ohm BNC terminator . 2. Make alar[...]

  • Page 5

    C808M-G (4/05) 5 Figure 2. VS5008 T erminated Camera Inputs - One Monitor Figure 3. VS5004 Alarm Connections VS5008 (REAR) MON 1 MON 2 MON X CAMERAS 87654321 12 V AC INPUT ALARM INPUT COM ALARM OUT 12345678 NOTE: MON 1 MUST BE TERMINA TED. MON 1 MON 2 1 2 3 4 1 2 3 4 ALARM 12V AC INPUT IN 1 2 3 4 COMMON 5 1 2 3 4 5 6 BRN RD OR YEL GRN BLK 6-PIN CON[...]

  • Page 6

    6 C808M-G (4/05) Figure 4. VS5008 Alarm Connections 12 V AC INPUT ALARM INPUT COM ALARM OUT 12345678 MON 1 MON 2 MON X CAMERAS 87654321 UP TO EIGHT ALARM INPUTS (ALARM INPUT FROM MOTION DETECTOR, DOOR CONT ACT , ETC., THROUGH NORMALL Y OPEN SWITCH). EACH ALARM DEVICE MUST BE CONNECTED TO THE "COM" TERMINAL. OPEN COLLECTOR OUTPUT FOR VCR A[...]

  • Page 7

    C808M-G (4/05) 7 LOOPING CAMERA INPUTS AND ONE MONITOR OUTPUT 1. Convert the switcher to looping operation. Refer to Figure 5 and do the following: NOTE: Looping and terminated inputs may be mixed. a. Remove the cover . b. Remove the rear panel of the chassis. c. Locate the 75-ohm resistors located on the inside of the rear panel BNC jacks. d. For [...]

  • Page 8

    8 C808M-G (4/05) Figure 5. Looping Conversion Modification Figure 6. VS5004 Looping Camera Inputs - One Monitor 75-OHM RESISTOR REAR PANEL (SWITCHER) BNC CONNECTOR CLIP HERE FOR EACH CHANNEL MON 1 MON 2 43 2 1 ALARM 12 V AC INPUT IN 1 2 3 4 OUT 6 COMMON 5 BRIGHT CONTRAST MON 1 VIDEO INPUTS ADDITIONAL EQUIPMENT TERMINA TED[...]

  • Page 9

    C808M-G (4/05) 9 Figure 7. VS5008 Looping Camera Inputs - One Monitor T ERMINATED CAMERA INPUTS AND T WO MONITOR OUTPUTS 1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following: a. Remove the cover . b. Remove the rear panel of the chassis. c. Remove the four screws attaching the PC board to the chassis. d. Pull the [...]

  • Page 10

    10 C808M-G (4/05) 4. Set the ALARM switch to the ON position. NOTES: • With all channel switches set to the AUTO position, both monitors immediately switch to the alarmed channel and the associated LED blinks. Multiple alarmed channels sequence every five seconds (VS5004) or three seconds (VS5008). The alarm has priority over the MONITOR/AUTO/BY[...]

  • Page 11

    C808M-G (4/05) 11 Figure 9. VS5004 T erminated Camera Inputs - T wo Monitors Figure 10. VS5008 T erminated Camera Inputs - T wo Monitors MON 2 MON 1 MON 2 43 2 1 ALARM 12 V AC INPUT IN 1 2 3 4 OUT 6 COMMON 5 BRIGHT CONTRAST BRIGHT CONTRAST MON 1 NOTE: IN THIS CONFIGURA TION, MON 1 MUST BE TERMINA TED WITH A 75-OHM TERMINA TOR AND MON 2 MUST BE IN T[...]

  • Page 12

    12 C808M-G (4/05) LOOPING CAMERA INPUTS AND T WO MONITOR OUTPUTS 1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following: a. Remove the cover . b. Remove the rear panel of the chassis. c. Remove the four screws attaching the PC board to the chassis. d. Pull the PC board and rear panel assembly out of the chassis. e. [...]

  • Page 13

    C808M-G (4/05) 13 7. Connect the AC adapter to the 12 V AC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 V AC (VS5004 or VS5008) or 230 V AC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing. 8. Using a screwdriver , adjust the DWELL interval control to the desired setting[...]

  • Page 14

    14 C808M-G (4/05) COAXITRON CONTROL To convert for use with a Coaxitron transmitter , do the following: 1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following: a. Remove the cover . b. Remove the rear panel of the chassis. c. Remove the four screws attaching the PC board to the chassis. d. Pull the PC board and rear[...]

  • Page 15

    C808M-G (4/05) 15 6. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO position. All unconnected video inputs should have their channel switch set to the BYP ASS position. NOTES: • VS5004 and VS5008 with one-monitor configuration: All channels with a switch set in the AUTO position will automatical[...]

  • Page 16

    16 C808M-G (4/05) Figure 13. VS5004 with Coaxitron Control Figure 14. VS5008 with Coaxitron Control COAXITRON® RECEIVER MON 1 MON 1 MON 2 43 2 1 ALARM 12 V AC INPUT IN 1 2 3 4 OUT 6 COMMON 5 LOOPING OUTPUT INPUT FROM RECEIVER OUTPUT FROM MONITOR J6 J7 J8 BRIGHT CONTRAST VS5004 (REAR) COAXITRON® TRANSMITTER (REAR) TO FIXED CAMERAS OR ADDITIONAL RE[...]

  • Page 17

    C808M-G (4/05) 17 Specifications VIDEO Inputs T erminating (75 ohms) or looping Outputs Monitor 1 75 ohms Monitor 2 VS5004 Hi Z VS5008 75 ohms Monitor X VS5008 Coaxitron transmitter (nonamplified) output Gain Unity Dwell Adjustable from 1-70 seconds nominal Frequency Response Flat within +/-1 dB to 10 MHz Maximum Signal Level 2 Vp-p T ilt Less th[...]

  • Page 18

    18 C808M-G (4/05)[...]

  • Page 19

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series [...]

  • Page 20

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East[...]