English dropdown-ico

Pelco IS150 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco IS150, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco IS150 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco IS150. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco IS150 should contain:
- informations concerning technical data of Pelco IS150
- name of the manufacturer and a year of construction of the Pelco IS150 item
- rules of operation, control and maintenance of the Pelco IS150 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco IS150 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco IS150, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco IS150.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco IS150 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INST ALLA TION C3427M-C (10/07) IS150 Series Camclosure ® Integrated Camera System[...]

  • Page 2

    2 C3427M-C (10/07)[...]

  • Page 3

    C3427M-C (10/07 ) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Page 4

    4 C3427M-C (10/07) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 Ceiling T [...]

  • Page 5

    C3427M-C (10/07 ) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE [...]

  • Page 6

    6 C3427M-C (10/07) Description The IS150 Series Camclosure ® integrated camera system combines an environmental cover , back box, camera, lens, and lower dome into a small, high-securi ty system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for multiple mou[...]

  • Page 7

    C3427M-C (10/07 ) 7 Indoor/outdoor dome, vandal resistant, in-cei ling mount, clear bubble, liner , gray finish PARTS LIST Camera T ype Lens/Iris NTSC P AL Color , Wide Dy namic Range, Day/Night 3-9.5 mm, Day/Night V arifocal, Auto Iris IS151-DWV9 9-22 mm, Day/Night Varifocal, Auto Iris IS151-DWV22 Color , High Resolution, Day/Night 3-9.5 mm, Day/N[...]

  • Page 8

    8 C3427M-C (10/07) Figure 1. Package Comp onents BA C K BOX (1) C AMERA MODULE (1) TRIM RING, LINER, AND C LEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-IN C H HOLLOW S C REWDRIVER BIT (1) ADAPTER PLA TE (1) SHOWN A C TUAL SIZE SHIPPING BOX 8-32 X 1.25-IN C H PHILLIPS FLA T HEAD S C REWS (4) 8-32 X 0.75-IN C H PHILLIPS FLA T HEAD[...]

  • Page 9

    C3427M-C (10/07 ) 9 Cover and Back Box Installation The IS150 Series Camclosure integrated camera system mounts only into a wall or ceiling. UNSHIELDED T WISTED PAIR (UTP) VIDEO The IS150 Series offers support fo r unshielded twiste d pair (UTP). The UTP video output signal is 1 Vp-p differential into a 100-ohm load. At a minimum, UTP requires Cat5[...]

  • Page 10

    10 C3427M-C (10/07) SUSPENDED CEILING NOTE: Y o u should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera modu le to access the mounting holes (refer to Came ra Module on page 12 for more informatio n). 1. Pull video and power wires to the c[...]

  • Page 11

    C3427M-C (10/07 ) 11 4S DEEP ELECTRICAL BOX NOTE: Y o u should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera modu le to access the mounting holes (refer to Came ra Module on page 12 for more informatio n). 1. Attach the supplied adapter p[...]

  • Page 12

    12 C3427M-C (10/07) Camera Module The IS150 Series Camclosure camera modu le includes the camera, came ra bracket, and heate r board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to re move and reinstall the camera module. MODULE REMOVAL T o remove the camera module from the back [...]

  • Page 13

    C3427M-C (10/07 ) 13 2. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 6). Figure 6. Back Box Conne ctors C AMERA C ONNE C TOR HEA TER BOARD C ONNE C TOR SERVI C E C ONNE C TOR[...]

  • Page 14

    14 C3427M-C (10/07) CAMERA ORIENTATION At the factory , the camera module is configured for ceiling mounting. For wall mountin g, you must change the camera orientation or the video image could be upside down or sideways. T o change the camera orientation (refer to Figure 7): 1. Remove the camera module from the back box if necessary. 2. Remove the[...]

  • Page 15

    C3427M-C (10/07 ) 15 Camera Adjustments T o perform the following camera adjustments, make su re to plug in the camera an d service connectors. Y ou may have to remove the camera module from th e back box. Connect a monitor . Then turn on power to the camera and monitor . T o use the service conne ctor , refer to Service Connector on page 26. T o s[...]

  • Page 16

    16 C3427M-C (10/07) DN/CH SERIES ADJUSTMENTS Refer to Figure 9 to adjust the IS150-DN or IS150-CH model. Figure 9. Adjusting the I S 150-DN/CH S eries Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: AGC (Auto Gain Control) The AGC (automatic gain control) adjusts the image autom atically to comp[...]

  • Page 17

    C3427M-C (10/07 ) 17 SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts. Set to ON to enable flickerless operation. The camera wi ll remove [...]

  • Page 18

    18 C3427M-C (10/07) V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one came ra to another . T o eliminate vert ical roll, reverse the 24 VAC connec tions on one camera. If both cameras are connected to t[...]

  • Page 19

    C3427M-C (10/07 ) 19 DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view ,[...]

  • Page 20

    20 C3427M-C (10/07) DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 11 to adjust the IS150-DW or IS150-CW model. Figure 11. Adjusting the I S 150-DW/CW S erie s Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set to ON for NT SC. Set to OFF for PAL. The default is ON. [...]

  • Page 21

    C3427M-C (10/07 ) 21 SW1-4: A WB (Auto White Balan ce)/MWB (Manual Whi te Balance) Auto white balance is enabled by defa ult (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video shows all white. 3. While holding the background in place, set SW1-4 to OFF . A green bloc[...]

  • Page 22

    22 C3427M-C (10/07) SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation. Use SW1-8 to set the general light levels at which th[...]

  • Page 23

    C3427M-C (10/07 ) 23 AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS150-DW and IS 150-CW Series Camclosures automatic ally adjust the camera to the auto iris. Auto iris level adjustments are not necessary. V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply, a brief vert[...]

  • Page 24

    24 C3427M-C (10/07) Camera Positioning Rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis ì in Figure 13). NOTE: Do not over -rotate the module. Excessively turni ng the module in one direction could result in damage to the wiring. Figure 13. Positioning the Camera ì T ilt 80° (20°–100°) î Pan 360°[...]

  • Page 25

    C3427M-C (10/07 ) 25 Install Liner and T rim Ring 1. Adjust the liner if installed (refe r to Figure 14): a. Align the screw holes in the trim ring with those in the back box to identify the proper liner position. b. Loosen the three Phillips screws located in t he trim ring. c. Insert the blade of a standard screwdriver in one of the adjustment gr[...]

  • Page 26

    26 C3427M-C (10/07) Service Connector The IS150 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the field of view and focus the camera. Figure 1 5. S ervice Connector Pelco offers two optional items that plug directly in to the service connector . Before us[...]

  • Page 27

    C3427M-C (10/07 ) 27 T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follo w the directions supplied with the mini ature coaxial connector . 2. Attach the 2.5 mm monaural plug to the other end of the coaxial cable (refer to Figure 16): a. Remove the support sleeve from the plug. b. Slip the support [...]

  • Page 28

    28 C3427M-C (10/07) Specifications GENERAL Pan/T ilt Adjustment Manual Pan 360° T ilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera mounting bracket and polycarbonate dome Finish White polyester powder coat trim ri ng with gray polyester powder coat back box Light Attenuation Smoked 1.5 F-stops light loss Clear [...]

  • Page 29

    C3427M-C (10/07 ) 29 2.42 (6.15) 1.75 (4.45) 3.50 (8.89) 5.48 (13.92) NOTE: VALUES IN PARENTHESES ARE C ENTIMETERS; ALL OTHERS ARE IN C HES. 3.75 (9.53)[...]

  • Page 30

    30 C3427M-C (10/07)[...]

  • Page 31

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warrant y are as noted below: • Five years on fiber o ptic products and TW3 000 Series unshield ed twisted pair tr a[...]

  • Page 32

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emi[...]