English dropdown-ico

Pelco es3012 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco es3012, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco es3012 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco es3012. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco es3012 should contain:
- informations concerning technical data of Pelco es3012
- name of the manufacturer and a year of construction of the Pelco es3012 item
- rules of operation, control and maintenance of the Pelco es3012 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco es3012 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco es3012, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco es3012.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco es3012 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    ES3012 Series Esprit ® C306M-K (4/05) ® INST ALLA TION MANUAL[...]

  • Page 2

    2 Pelco Manual C306M-K (4/05)[...]

  • Page 3

    Pelco Manual C306M-K (4/05) 3 CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS ............................................................................ 5 DESCRIPTION ................................................................................................................... 6 MODELS ...................................................[...]

  • Page 4

    4 Pelco Manual C306M-K (4/05) LIST OF ILLUSTRA TIONS Figur e Page 1 Esprit ES3012 System Dimensions Drawing .................................................... 37 LIST OF TABLES T able Page A Switch Settings for SW1 ................................................................................... 32 B Switch Settings for SW2 ....................[...]

  • Page 5

    Pelco Manual C306M-K (4/05) 5 IMPOR T ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, st[...]

  • Page 6

    6 Pelco Manual C306M-K (4/05) DESCRIPTION The Esprit ® ES3012 Series Integrated Positioning System is available as a basic system or as an ImagePak ® camera and lens package. The basic system integrates a pan and tilt, camera enclosure, and receiver (camera and lens not included). The ES3012 ImagePak in- cludes the basic system, plus a camera and[...]

  • Page 7

    Pelco Manual C306M-K (4/05) 7 INST ALLA TION The basic ES3012 system does not include a camera and lens package. Therefore you must install a camera and lens in the enclosure before mounting the pan/tilt to the base of the system. CAMERA AND LENS INST ALLA TION (Skip this section if you are installing an ES3012 ImagePak camera and lens package. Sta[...]

  • Page 8

    8 Pelco Manual C306M-K (4/05) A B 3 Attach the camera and lens to the mount. Extend the lens to the maximum length before positioning the camera and lens. A . Position the camera and lens so the lens does not extend beyond the end of the mount. B. Fasten the camera and lens to the mount with the 1/4-20 Phillips screws, lock washers, and flat washer[...]

  • Page 9

    Pelco Manual C306M-K (4/05) 9 P AN AND TIL T INST ALLA TION 1 When installing the ES3012 Esprit system, allow for sufficient clear- ance between the top of the unit and overhead obstructions. This will prevent interference when the en- closure is driven to its maximum el- evation of 40 degrees. 2 Remove the transformer module from the base of the s[...]

  • Page 10

    10 Pelco Manual C306M-K (4/05) 4 Route the wires and cables through the center of the Esprit mount. Re- install the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. 5 ES3012-5 Model Only – Set the 120/230 voltage selector switch on the trans- former to the appropriate voltage. 6[...]

  • Page 11

    Pelco Manual C306M-K (4/05) 11 8 T urn on the power . If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the T roubleshooting section. 9 Plug the male Esprit system connector , located on the bottom of the pan and tilt, into the female Esprit system connector located on the transformer mo[...]

  • Page 12

    12 Pelco Manual C306M-K (4/05) TXB SERIES TRANSLA TOR BOARD INST ALLA TION (OPTIONAL) Pelco’s TXB Series allows controllers from other companies to communicate with the Esprit system. T o install a TXB Series board, remove the left cover of the pan and tilt. Once the cover is removed, refer to the manual supplied with the translator board to comp[...]

  • Page 13

    Pelco Manual C306M-K (4/05) 13 T o reinstall the pan and tilt cover, do the following: 1. Properly position the cover and slide it into place. The sides of the cover must fit under the front and back rain guards of the pan and tilt, and the top of the cover must seat against the lip of the top gasket. 2. Apply pressure and push the top of the cover[...]

  • Page 14

    14 Pelco Manual C306M-K (4/05) OPERA TION POWER-UP DISPLA Y When the Esprit system is powered up or reset, the selected protocol, revision number , and other information is displayed on the monitor . For example, the screen might show the fol- lowing information: The information displayed depends on the selected protocol (C, D, or P) and the menu s[...]

  • Page 15

    Pelco Manual C306M-K (4/05) 15 P AN, SCAN, AND TIL T SPEEDS Pan and scan speeds are adjustable from 3 to 40 degrees per second through the pro- gramming menu. The tilt speed is one-half of the pan speed. LENS FUNCTIONS Lens zoom, focus, and iris functions are operated from the controller . All lens models have motorized zoom and focus, and direct-d[...]

  • Page 16

    16 Pelco Manual C306M-K (4/05) PROGRAMMING ESPRIT MENUS T o access the main menu, program preset 95. T o make selections in the main menu, use the following controls: Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter . Iris Close: Cancel. For detailed programming instructions, refer to the sections on th[...]

  • Page 17

    Pelco Manual C306M-K (4/05) 17 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for v[...]

  • Page 18

    18 Pelco Manual C306M-K (4/05) AZ/EL Other Menu Park Time 0 Pan/Scan Spd 7 Power Up Default Pat length 6 min Spd Profile 50 MPH wind <Zone Blank> <Az /El/ Direction> Exit Az/El/Direction Set Azimuth Zero Az/El Az/El Line Direction Direction Line Disp Duration Exit Az/El programs the horizontal display position of the Azimuth 1 /Elevatio[...]

  • Page 19

    Pelco Manual C306M-K (4/05) 19 AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. T o program the vertical label position [...]

  • Page 20

    20 Pelco Manual C306M-K (4/05) AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the programmed 0 ° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point. T o set azimuth zero: 1. Program preset 95 (28). The main menu ap[...]

  • Page 21

    Pelco Manual C306M-K (4/05) 21 DIRECTION Direction programs the horizontal display position of the Direction label (N, NW , NE, …). The following settings are available for the Direction label: Off – Label is not displayed. Left – Label is displayed on the left-hand side of the screen. Center – Label is displayed in the center of the screen[...]

  • Page 22

    22 Pelco Manual C306M-K (4/05) DIRECTION LINE NOTE: Direction display is not available while you are programming or running a pattern. Other Menu Park Time 0 Pan/Scan Spd 7 Power Up Default Pat length 6 min Spd Profile 50 MPH wind <Zone Blank> <Az /El/ Direction> Exit Az/El/Direction Set Azimuth Zero Az/El Az/El Line Direction Direction[...]

  • Page 23

    Pelco Manual C306M-K (4/05) 23 DISPLA Y DURA TION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor . The available settings for display duration include the following: CONST ANT - The label is displayed continuously . 2 SECONDS (default) - The label is displayed for 2 seconds after PTZ functi[...]

  • Page 24

    24 Pelco Manual C306M-K (4/05) LIMIT STOPS TURNING LIMIT STOPS ON OR OFF T o change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limits. 3. Press the Iris Open button to enter the Limits menu. 4. Position the cursor (>) beside Limit Stops. 5. Press the Iris Open button. The cursor mo[...]

  • Page 25

    Pelco Manual C306M-K (4/05) 25 Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached. The manual scan limit stops can be set in one of two ways: At the controller by programming presets 92 (25) and 93 (26) or At the controller by programming the Limit [...]

  • Page 26

    26 Pelco Manual C306M-K (4/05) P AN/SCAN SPEED The pan/scan speed is adjustable from 3-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. T o change the pan/scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other . 3. Press the Iris Open button to enter the Other me[...]

  • Page 27

    Pelco Manual C306M-K (4/05) 27 POWER-UP MODE This feature lets the system resume a desired condition following power-up. The menu in- cludes the following choices. • Default - On power-up, the pan and tilt goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen. ?[...]

  • Page 28

    28 Pelco Manual C306M-K (4/05) SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second. The dif ference will be in th[...]

  • Page 29

    Pelco Manual C306M-K (4/05) 29 ZONES Basic rules for setting zones: 1. Refer to the documentation for your control system to program zones. 2. Establish zones using the controller , prior to programming ZONE BLANK with the Es- prit onscreen menu. 3. T o accurately set zone areas, zoom wide to the maximum field of view. 4. Set zones moving the joyst[...]

  • Page 30

    30 Pelco Manual C306M-K (4/05) TROUBLESHOOTING Symptom: System does not operate. 1. Check system input voltage. 2. Check for proper positioning of input power select switch for the transformer (ES3012-5 models only). 3. The Esprit system is protected by a resettable overcurrent protective device located in the transformer module. Whenever a fault c[...]

  • Page 31

    Pelco Manual C306M-K (4/05) 31 Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camera to the monitor . 4. Make sure the controller is set for the correct camera-to-monitor viewing combination[...]

  • Page 32

    32 Pelco Manual C306M-K (4/05) APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. T able A. Switch Settings for SW1 Baud Rate Switch Setting SW1-1 SW1-2 SW1-3 2400 OFF OFF OFF* 4800 O[...]

  • Page 33

    Pelco Manual C306M-K (4/05) 33 T able B. Switch Settings for SW2 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. Receiver Address Switch Setting P-T ype D-Type Control Control SW2-1 SW2[...]

  • Page 34

    34 Pelco Manual C306M-K (4/05) T able B. Switch Settings for SW2 (continued) (Continued on next page) Receiver Address Switch Setting P-T ype D-Type Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 112 OFF OFF OFF OFF ON ON ON OFF – 113 ON OFF OFF OFF ON ON ON OFF – 114 OFF ON OFF OFF ON ON ON OFF – 115 ON ON OFF OFF ON ON [...]

  • Page 35

    Pelco Manual C306M-K (4/05) 35 T able B. Switch Settings for SW2 (continued) Receiver Address Switch Setting P-T ype D-Type Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 232 OFF OFF OFF ON OFF ON ON ON – 233 ON OFF OFF ON OFF ON ON ON – 234 OFF ON OFF ON OFF ON ON ON – 235 ON ON OFF ON OFF ON ON ON – 236 OFF OFF ON ON [...]

  • Page 36

    36 Pelco Manual C306M-K (4/05) SPECIFICA TIONS ELECTRICAL Input Voltage: 24 or 120/230 V AC, 50/60 Hz; on ES3012-5 models, a switch is installed on the transformer module located in the mount base to make 120 or 230 V AC input voltage selection. Reset feature enabled when power becomes unstable or interrupted. Power Requirements: Maximum power cons[...]

  • Page 37

    Pelco Manual C306M-K (4/05) 37 Figure 1. Esprit ES3012 System Dimensions Drawing 13.8 (35.1) 4.1 (10.5) 14.0 (35.5) 4.8 (12.3) 9.1 (23.2) 7.7 (19.7) 6.9 (17.5) 7.9 (20.2) 16.4 (41.7) 5.2 (13.3) NOTE: V ALUES IN P ARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. 17.3 (43.9)[...]

  • Page 38

    38 Pelco Manual C306M-K (4/05) REGULA TORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This equipment generates, uses, and can radi[...]

  • Page 39

    Pelco Manual C306M-K (4/05) 39 Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy , and Spectra are registered trademarks of Pelco. ©Copyright 2005, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved. Lexan is a registered trademark of the General Electric Company . REVISION HISTOR Y Manual # Date Comments C306M 1/99 Origi[...]

  • Page 40

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East[...]