Pelco DVR5KRP-400 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco DVR5KRP-400, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco DVR5KRP-400 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco DVR5KRP-400. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco DVR5KRP-400 should contain:
- informations concerning technical data of Pelco DVR5KRP-400
- name of the manufacturer and a year of construction of the Pelco DVR5KRP-400 item
- rules of operation, control and maintenance of the Pelco DVR5KRP-400 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco DVR5KRP-400 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco DVR5KRP-400, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco DVR5KRP-400.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco DVR5KRP-400 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Hard Disk Drive Replacement Instructions C2647M (10/06)[...]

  • Page 2

    2 C2647M (10/06) Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Page 3

    C2647M (10/06) 3 Introduction This manual provides instructio ns for installing a replacement ha rd di sk drive or upgrading to a higher capacity hard disk drive in a DVR510 0 Series D VR (digital vi deo recorder). MODELS The following models numbers are available f or hard disk rep lacements or upgrades for t he DVR5100: PARTS AND T OOLS NOTE: Thi[...]

  • Page 4

    4 C2647M (10/06) Getting Started 1. Familiarize yourself with the inst ructi ons througho ut this manual. 2. Check that you ha ve all the necessary parts and tools. Refer to Parts and T o ols on page 3. 3. If possible, export all essent ia l video before you install a new hard disk d r ive. If your unit contains two hard disk drives, expo rt all es[...]

  • Page 5

    C2647M (10/06) 5 6. Ensure that the DVR5 100 DVR and all of its componen ts are protected from electr ostatic discharge (ESD). Before handling an y electronic co mponents, you sh ould take step s to ground yourself pr operly so that any built- up static electric cha rges are diss ipated away fro m the unit. Th e most effectiv e method for combating[...]

  • Page 6

    6 C2647M (10/06) Hard Disk Drive Replacement PREPARING THE UNIT TO INSTALL A DRIVE 1. Log off the system an d shut down the ma chine. The power will tu rn off automatically . 2. As a preca ution again st electros tatic shock, remove the power cord from th e rear panel of the unit, a nd then disconnect a ll devices atta ched to it. Use the enclosed [...]

  • Page 7

    C2647M (10/06) 7 INSTALLING A HARD DISK DRIVE 1. Follow the instructions at Prep aring the Unit to Install a D rive on page 6 to open your unit. 2. Locate the hard disk drive cage in the front of the DVR. Figure 6. Locating the Hard Disk Drive Cage 3. T o remove a hard disk drive do the fo llowing: a. With a Phillips screw d river , remove and set [...]

  • Page 8

    8 C2647M (10/06) b. Lift up and slide the cage out from un der the ret ainer bracket . Notice tha t there are two tabs alon g the bottom of the cage t hat se cure it in place. Figure 8. Removing the Hard Disk Drive Cage c. Remove the po wer and data ca ble from both of the drives in the cage. Figure 9. Removing the Power Cable[...]

  • Page 9

    C2647M (10/06) 9 d. With a Phillips screw d river , remove and set a side the four screws t hat secure the dr ive to the sides of the cage. Figure 10. Removing the Screws from Hard Disk Drive in the Cage e. Slide the dr ive out of t he cage being careful to avoid sc ratching the bottom of the drive against th e metal of the cage. Figure 11. Remo vi[...]

  • Page 10

    10 C2647M (10/06) 5. T o return the cage to the cha ssis do the following: a. Attach the p ower and data cable to the drive or drive s. b. Place th e cage in the chassis and guid e the tabs under th e retainer bra cket. Figure 12. Inserting the Hard Disk Drive Cage in the Chassis c. Fasten the two screws to the chassis. Do not overtighte n the scre[...]

  • Page 11

    C2647M (10/06) 11 REASSEMBLING THE UNIT 1. Replace the lid, and use the ori ginal screws t o secure the l id in place. 2. Reattach any devices that you disconnect ed from the unit (refe r to Figure 15). 3. Reconnect the p ower cord. 4. Restart the DVR5100, and then enter a user name and p assword on the Login scree n to log on to the system. NOTE: [...]

  • Page 12

    12 C2647M (10/06) REAR PANEL CONNECTO RS FOR THE DVR5100 Figure 15. DVR5100 Rear Panel The following table describes the DVR5 100 back panel. T able A. Parts of the DVR5100 Back Panel Item Part and Description Audio Inputs 1 and 2: Audio inp uts are assigned as follows: • T wo audio in puts (1 and 2 for video inp ut 1 and 2, respectivel y) are pr[...]

  • Page 13

    C2647M (10/06) 13 Relay s 1–2: One relay is provide d for every 4 channels: • One relay ou tput is pro vided for a 4-ch annel DVR. • T wo relay outputs (1, 2 for channels 1 and 2, respect ively) are provided fo r an 8-channel DVR. • Four relay outpu ts (1, 2 for channels 1 and 2, respectively and 3, 4 fo r channel 9 and 10, respectively) a [...]

  • Page 14

    14 C2647M (10/06) RJ-45 Port: Supports an RS-422 port for conn ecting a PTZ device. Alarms 9–12 and 13–16: One programmable a larm input is provided for each video input . Alarm inputs for video input 9–16 are or ganized as f ollows: • Alarm inpu t 9–12 for vide o 9–12 • Alarm input 13–16 fo r video input 13–1 6 Alarms are numberd[...]

  • Page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRA NTY Pelco will r epair or repla ce, without charge, any merchandise p roved defectiv e in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are a s noted below: • Five years on FR/F T/FS Series fiber optic products and TW3 000 Series unshielded t[...]

  • Page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherl ands | United Ar ab Emirates | United Kingdom | Un[...]