English dropdown-ico

Pelco C2495M-A manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco C2495M-A, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco C2495M-A one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco C2495M-A. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco C2495M-A should contain:
- informations concerning technical data of Pelco C2495M-A
- name of the manufacturer and a year of construction of the Pelco C2495M-A item
- rules of operation, control and maintenance of the Pelco C2495M-A item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco C2495M-A alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco C2495M-A, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco C2495M-A.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco C2495M-A item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INST ALLA TION ICS-DO111ABK Integrated Camera System MR5000 Series Public V iewing System C2495M-A (1/06)[...]

  • Page 2

    2 C2495M-A (1/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other [...]

  • Page 3

    C2495M-A (1/06) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class B (except auto iris models[...]

  • Page 4

    4 C2495M-A (1/06) Description Designed specifically for the MR5000 Series public viewing system, the ICS-DO111ABK integrated camera system packages a camera and lens into a small, discreet, high-security dome. Pelco’ s MR5000 Series public viewing system is specifi cally designed for retail applications to provide a clear , visual warning to po[...]

  • Page 5

    C2495M-A (1/06) 5 Installation PREPARE VIDEO AND ELECTRICAL CABLING 1. T emporarily remove the bottom end cap of the MR5000 Series mount if the end cap is installed. 2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount arm and out the bottom end of the mount arm. 3. Pull power wires through the ICS-DO111ABK f[...]

  • Page 6

    6 C2495M-A (1/06) INSTALL THE ICS-DO111ABK TO THE MR5000 MOUNT Follow the steps below to install the ICS-DO111ABK to the MR5000 mount: 1. Align the adapter plate with the cover. Position the cover so that the notch on the side of the cover faces the back of the MR5000 mount. 2. Using the two 10-32 x 0.375-inch pan head screws and internal lock wash[...]

  • Page 7

    C2495M-A (1/06) 7 3. Do the following to install the back box inside the cover of the ICS-DO111ABK: a. Feed the video cable and power wires attached to the ICS-DO111ABK back box through the cover and adapter plate of the ICS- DO111ABK. b. Rotate and position the back box so that the conduit plug on the side of the box is located on the opposite sid[...]

  • Page 8

    8 C2495M-A (1/06) Install Camera 1. Some indoor installations do not require a heater . If the installation does not require a heater , remove the heater board from the camera assembly. T o remove the heater press on an end of the board. 2. 12 VDC operation only: The camera is set for 24 V AC operation at the factory. For 12 VDC operation remove th[...]

  • Page 9

    C2495M-A (1/06) 9 5. Always make sure the tab on the camera bracket is pointing out of the enclosure (away from the ceiling or wall). Gently squeeze the bracket, place it against the groove inside the back box, and gently release. Proper camera orientation: CAMERA BRACKET T AB ALW A YS POINTS OUT OF THE ENCLOSURE TOP OF CAMERA CAMERA BRACKET T AB A[...]

  • Page 10

    10 C2495M-A (1/06) Install Dome and T rim Ring 1. Align the screw holes in the trim ring with those in the Camclosure base. 2. Domes with Liners (only) – Position the viewing window over the lens of the camera by doing the following: a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of th[...]

  • Page 11

    C2495M-A (1/06) 11 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, it may be necessary to remove the heater board in order to loosen the lockin[...]

  • Page 12

    12 C2495M-A (1/06) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture de[...]

  • Page 13

    C2495M-A (1/06) 13 SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. For manually setting and locking the white balance, place a white background in front of camera and turn off switch 1. For gamma correction, switch to accurately reproduce scene b[...]

  • Page 14

    14 C2495M-A (1/06) Specifications General Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fi tting and 3/4-inch (1.91 cm) opening for NPT threaded pipe Pan/T ilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel camera mounting bracket and polycarbonat[...]

  • Page 15

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p[...]

  • Page 16

    United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001[...]