NEC N8100-1125F manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of NEC N8100-1125F, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of NEC N8100-1125F one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of NEC N8100-1125F. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of NEC N8100-1125F should contain:
- informations concerning technical data of NEC N8100-1125F
- name of the manufacturer and a year of construction of the NEC N8100-1125F item
- rules of operation, control and maintenance of the NEC N8100-1125F item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of NEC N8100-1125F alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of NEC N8100-1125F, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the NEC service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of NEC N8100-1125F.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the NEC N8100-1125F item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    N8100-1061F/1062F/ 1063F/1100F/112 5F/1126F NEC Express5800/120Rh-2 User's Guide 5th Edition 5-2006 ONL-4133eN-120Rh2-100-99-0604[...]

  • Page 2

    PROPRIET AR Y NOTICE AND LIABILITY DISCLAIMER The information disclosed in this docu ment, including all designs and related materials, is the valuable pro perty of NEC Corporatio n (NEC) and /or its licensors. NEC and/or its licenso rs, as appropriate, rese rve all patent , copyright a nd other proprietary ri ghts to this d ocument, i ncluding all[...]

  • Page 3

    Keep this User's Guide at hand for qui ck reference at anytime necessary . SAFETY INDICA TIONS Follow the instructions in this User's Gu ide for your safety to use the server. The server contains compon ents with possible danger , hazards that may cause by ignorin g warnings, and preventive actions against such hazards. Server components [...]

  • Page 4

    SYMBOLS USED IN THIS USER'S GUIDE AND W ARNING LABELS Attentions Indicates that improper use may cause an electric shock. Indicates that improper use may cause pers onal injury. Indicates that improper use may cause fingers to be ca ught. Indicates that improper use may cause fumes or fire. Indicates a general notice or warning that cann ot be[...]

  • Page 5

    NOTE: This equipment has been tested and found to comply with the li mits for a Class A digital device, pursuant t o Part 15 of the FCC Rules. These lim its are designed t o provide reas onable protection against harmful interfe rence when the equi pment is operated in a comm ercial environm ent. This equi pment generat es, uses, and can radiate ra[...]

  • Page 6

    T rademarks NEC DianaScope, NEC ESMP RO and NEC EXPRESSBUILDER are trademarks of NEC Corporation. Microsoft, W indows, W indows Server , W indows NT , and MS- DOS are registered tradem arks or trademarks of Microsoft Corporation in the United States and other countries. Intel, Pentium, and Xeon are registered tradem arks of Intel Corporation . Data[...]

  • Page 7

    i PREF ACE W elcome to the NEC Express5 800/120Rh-2 se rver . The NEC Expres s5800 server holds powerful perf ormance and em ploys the latest technol ogy to implement a computer for the next generation. W ith its poten tial capabilities, the server may be used as the work station PC that c onfigures a cl ient-server system and provides high-speed p[...]

  • Page 8

    ii ABOUT THIS USER'S GUIDE This User's Guide is a guide for pr oper setup and use of the server . This User's Guide also covers usefu l procedures for dealing with difficulties and problems that may arise during set up or operat ion of the serve r . Keep this manual for future use. The following describes how to proceed with this Use[...]

  • Page 9

    iii Appendix C IRQ and I/O Port Address provides a list of factory-set IRQs and I/O port addresses assigned. Appendix D Inst alling Windo w s Server 2003 x64 Editions describes how to install Microsoft Windows Server 2003 x64 Editions without using Express Setup. Using the Express Setup tool is reco mmend ed for installing Windows Server 2003 x64 E[...]

  • Page 10

    iv CONTENTS Preface ........................................................................................................................ ...................... i About This Us er's Guide ........................................................................................................ ..........ii In the Package .....................[...]

  • Page 11

    v System Boar d Feat ures .......................................................................................................... ..... 2-18 Processor ...................................................................................................................... .......... 2-18 Memory ......................................................[...]

  • Page 12

    vi Chapter 4 Configuri ng Y our Se rver .............................................................................. 4-1 System BIOS (SET UP) ............................................................................................................ .... 4-1 Starting SE T UP U tility ..............................................................[...]

  • Page 13

    vii Chapter 6 Inst alling a nd Using Utilit ies ....................................................................... 6-1 NEC EXPRESSB UILDER ........................................................................................................... 6- 2 NEC EXPRESSBUILDER for DOS-Ba sed with Local Console ........................................[...]

  • Page 14

    viii Problems with Configuratio n Dis kette Creator ..................................................................... 8-26 Problems with Disk Arra y Configura tion .............................................................................. 8-26 Collecting Ev ent Log ............................................................................[...]

  • Page 15

    ix Appendix D Inst alling Windows Server 2003 x64 Editions........................................ D-1 Before Installing W indows Se rver 2003 x6 4 Editions ................................................................. D-1 Optional Board Supported by NEC EXPRESSBUIL DER ...................................................... D-1 Updating System [...]

  • Page 16

    x Driver Installation and Advanced Settings ................................................................................. E-15 PROSet ......................................................................................................................... ......... E-15 Network Driver.............................................................[...]

  • Page 17

    Chapter 1 Notes on Using Y our Server This chapter includes information necessary fo r proper an d safe operation of th e server .[...]

  • Page 18

    1-2 Notes on Using Y our Server W ARNING LABELS The warning label is attached to componen ts with possible danger or their vicinity in your server to inform the user that a hazard ous situation may arise when operating the server . (Do not intentionally remove or dam age any of the labels.) If you find any labels totally/partially removed or illegi[...]

  • Page 19

    Notes on Using Y our Server 1-3 SAFETY NOTES This section provides notes on using th e server safe ly . Read this section carefully to ensure proper and safe use of the serve r . For symbols, see "SAFETY INDICA TIONS" provided earlier . General W A RNI NG Do not use the server for services where critical high avail ability may directly af[...]

  • Page 20

    1-4 Notes on Using Y our Server CA UTION Keep water or foreign matter away from the server. Do not let any form of liquid ( water etc.) or foreign matter (e.g., pins or paper clips) enter the server. Failure to follow this warning may caus e an electric shock, a fire, or a failure of the server. When such things accidentally enter the server, immed[...]

  • Page 21

    Notes on Using Y our Server 1-5 Power Suppl y and Power Cord Use W A RNI NG Do not hold the power plug with a wet hand. Do not disconnect/connect the plug while your hands are wet. Failure to follow this warning may cause an electric shock. Do not connect the ground wire to a gas pipe. Never connect the ground wire to a gas pipe. Failure to follow [...]

  • Page 22

    1-6 Notes on Using Y our Server Rack CA UTION Do not carry or install the server only b y a single person. More than one person is required to carry or insta ll the rack. Failure to follow this instruction may cause the rack to fall to result in personal injur y and/or breakages of surrounding dev ices. In particular, a high rack (such as 44U rack)[...]

  • Page 23

    Notes on Using Y our Server 1-7 Inst allation, Relocation, Storage, and Connection W A RNI NG Disconnect the power cord(s) before installing or removing the serv er. Make sure to power off the server a nd disconnect the power cord(s) from a power outlet before installing/remov ing t he server. All voltage is removed only when the power cords are un[...]

  • Page 24

    1-8 Notes on Using Y our Server CAUTION Do not connect any interface cable with the power cord of the server plugged to a power source. Make sure to power off the server and unplug the po wer cord from a power outlet before installing/remov ing any optional internal d evice or connecting/disconnecting an y interface cabl e to/from the server. If th[...]

  • Page 25

    Notes on Using Y our Server 1-9 Cleaning and Working with Internal Devices W A RNI NG Do not disassemble, repair, or alter the server. Never attempt to di sassemble, repair, or alter the server on any occa sion other than described in this User's Guide. Fail ure to follow this instruction may cause an electric shock or fire as well as malfunct[...]

  • Page 26

    1-10 Notes on Using Y our Server During Operation CAUTION Do not pull out or remove the server from the rack unnecessar ily. Do not pull out or remove the server fr om the rack unnecessarily. Pulling out or removing the server from the rack ma y cause not only the server to oper ate incorrectly but also the server to fall on people to make them inj[...]

  • Page 27

    Notes on Using Y our Server 1-1 1 FOR PROPER OPERA TION Observe the following notes for su ccessful operation of the server . Use of the server i gnoring the notes will cause malfunctions or failures of the server .  Install the rack assembly in a place that m eets requirem ents for successful operatio n. For details, see Chapter 3, "Settin[...]

  • Page 28

    1-12 Notes on Using Y our Server  Store the unit under the st orage conditi on (temperature: –10°C - 55°C , humidity: 20% - 80%, without condensation) to allow built-in devices and the unit to operate correctly in the next ope ration.  Make sure t o use optional devices supporte d by the server . Some no n-supported devices may be physica[...]

  • Page 29

    Notes on Using Y our Server 1-13 TRANSFER T O THIRD P ARTY The following must be observ ed when you transfer (or sell) the server or software provided with the ser ver to a thir d par ty: Server Hardware Make sure to provide this User's Guid e along with the server to a third party . Provided Sof tware T o transfer or sell any software app lic[...]

  • Page 30

    1-14 Notes on Using Y our Server DISPOSAL AND CONSUMABLES  Dispose the server , all the internal devices , floppy disks, and CD-ROMs accordi ng to all national laws and regulatio ns. IMPORT ANT : For disposal (or replacem ent) of the battery on the mother board of the server , consu lt with your service representativ e.  The server cont ains [...]

  • Page 31

    Notes on Using Y our Server 1-15 USER SUPPORT Before Ask ing for Repair , do the following when the serv er appears to fail: 1. Check if the power cord and the cables t o other devi ces are properly connected. 2. See Chapter 8 to find if your problem fits the description. If it does, take the recommended measure for it. 3. Check if the software req[...]

  • Page 32

    1-16 Notes on Using Y our Server Advice for Health The longer you keep us ing the computer equipment, the more you becom e tired, which may cause disor ders of your body . When you use a computer , observe the follo wing to keep yourself from getting tired: Good Working Posture Y ou have good posture if the following ar e satisfied when you use a c[...]

  • Page 33

    Chapter 2 General Description This chapter provides information that you should be familiar with before using the server . It includes nam es and functions o f the componen ts and features o f the server . OVERVIEW Y our server is a modular, multiprocessing server based on the Intel  Xeon  microprocess or . It is a solid perf ormer and of fer[...]

  • Page 34

    2-2 General Description External V iew 1 Dri ve co ve r 2 Logic cover 3 S w itches, indicators, and front I/Os 4 Optical disk drive (CD-ROM drive) 5 Floppy disk drive 6 Backup file device bay 7 SCSI hot-plug hard disk drive bay 1 2 7 3 4 5 6[...]

  • Page 35

    General Description 2-3 Front V iew with Front Bezel Closed The following figur e shows the loca tion of the front system features. ID 1 F ront bezel The front bezel is a cover protecting the front dev ices during da ily operation. A security key is provided to lock the cover . 2K e y s l o t Insert the security key into this slot when unlocking th[...]

  • Page 36

    2-4 General Description Front V iew with Front Bezel Removed 1 Captive thumb screws (1 at the right and left each) The screws secure the server to the rack. 2 Handles (1 at the right and left each) Hold the handles when dismounting/mounting the server from/in the rack. 3 Hard disk drive bays Mount hard disk drives in the ba ys. Each num ber followi[...]

  • Page 37

    General Description 2-5 8 Serial port B (COM B) connector Used to communicate with the remote console via direct connection. 9 Backup device bay Mount an optional DA T or AIT drive in this bay . 10 3.5-inch floppy disk drive This drive reads/writes data from/to the 3.5-inch floppy disk. 10 -1 Disk access LED 10 -2 Disk slot 10 -3 Eject button 1 1 U[...]

  • Page 38

    2-6 General Description Rear View 1 Low-profile PCI board extension slo t s Mount PCI boards of the low-profile type into th e slots. The slots are called 3C, 2C, and 1C from top. 2 Capti ve thumbs crew Secure the logic cover . 3 Full-height PCI board exte nsion slot s Mount PCI boards of the full-height type in the slots. The slots are called 3B, [...]

  • Page 39

    General Description 2-7 1 1 UID (Unit ID) switch Press this switch to turn on/of f the UID LEDs on the front and rear panels of the server . Pressing the switch once turns on the LEDs. Pressing it again turns them off. 12 DUMP switch Press this switch to dump memory . 13 Serial port A (COM A ) connector Connect device having a serial i nterface to [...]

  • Page 40

    2-8 General Description Internal V iew 1 SCSI backplane 2 Cooling fans 2 -1 : F AN1 2 -2 : F AN2 2 -3 : F AN3 2 -4 : F AN4 3 Support arm 4 Power supply unit 5 Remote ma nagement card 6 Mother board 7 Riser card 8 Chassis intrusion switch 9 DIMM (T wo DIMMs are mounted as st andard in slot s #7 and #8.) 10 Processor (mounted under the CPU and heat s[...]

  • Page 41

    General Description 2-9 Mother Board 1 Main power connector 2 L ithium battery 3 CMOS clear jumper switch 4 Hard disk drive access L ED pin header (Connect the LED relay cable of an additi onal SCSI/RAID controller .) 5 Remote management card so cket 6 SCSI 1 connector (for SCSI hard disk drives) 7 SCSI 2 connector (for backup file device) 8 Passwo[...]

  • Page 42

    2-10 General Description ST A TUS INDICA TORS This section e xplains the in dication and m eanings of the se rver LEDs. POWER LED ( ) The green POWE R LED lights to indicate norm al operation while the ser ver is powered . Wh en the server is off-powered , the POWER LED stays unlit. The POWER LED indicates that the server is runni ng in the power-s[...]

  • Page 43

    General Description 2-1 1 ST A TUS LED indication Description Procedure On (green) The server is operating normall y . – Flashing (green) • The server is operating with the memory , CPU in de graded state. • An uncorrectable memory error has often occurred. Check the AC POWER LED indication on the rear panel of the server . Identify the devic[...]

  • Page 44

    2-12 General Description DISK ACCESS L ED ( ) The DISK ACCESS LED indicat es the status of the hard disk drive mounted in t he 3.5-inch dis k bay . The LED turns green each time access is made to the hard dis k drive. When the DISK ACCESS LED turns amber , it indicates that a hard di sk drive failure has occurred. Check the hard disk driv e LED for[...]

  • Page 45

    General Description 2-13 Hard Disk Drive LED The disk LED m ounted in the 3.5-inch di sk bay indicates the following depen ding on the stat us:  Flashing (green) The LED indicates that the hard disk dri ve is accessed.  On (amber) The LED indicat es a failure of a har d disk drive m ounted in disk array configuration. NOTE: Even if one of t h[...]

  • Page 46

    2-14 General Description LAN Connector LEDs There are two LED s for each of the two LA N ports (connectors) on the rear pane l.  LINK/ACT LED Each LINK/ACT LED indicates the status of the standard network por t of the server . While power is supplied to the server and HUB and the conn ection is correct, the LED is on (green). The LED turns gree [...]

  • Page 47

    General Description 2-15 AC POWER LED There is an AC POWER LED for t he power suppl y unit on the rear . T he LED turns green and flashes when the power supply un it receives AC power from the pow er co rd, which is connected to the AC inlet. The LED turns g reen when the ser ver power swit ch is turned on. If the LED does not go on when the server[...]

  • Page 48

    2-16 General Description ST ANDARD FEA TURES High performance Expandability  Intel  Xeon  Processor (3.20DGHz / 3.20GHz / 3.40GHz / 3.60GHz / 3.80GHz)  High-speed network interface (1000Mbps/100Mbps/10Mbps supporte d)  High-speed disk access (Ultra320 SCSI)  High-speed memory access (DDR 2-400)  Three full-length, full-height 6[...]

  • Page 49

    General Description 2-17 Power Supplies The power s upply consists of the power supply bay a nd one power su pply module. A second power supply m odule can be purc hased to provide a redundant , 1+1 system . W ith either confi guration, the power supply pro vides 600 watts of power an d is designed to minimize EMI. The power s ubsystem supports imp[...]

  • Page 50

    2-18 General Description SAF-TE LOGIC NOTE: SAF-TE Logic is in system s that include the hot-swap SCSI disk drive cage. SAF-TE Logic is not availabl e in systems that include the standard SCSI disk drive cage. The SCSI backpl ane includes SAF-TE ( SCSI Accessed Fault T olerant Enclosure) logi c that provides an interface to the dis k subsystem that[...]

  • Page 51

    General Description 2-19 PCI Riser Slot s The mother board has t wo PCI riser slots. Ri ser slot B provides th e following features:  Bus speed up to 100 MHz  184 pin, 5 volt ke yed, 64-bit expa nsion slot connecto r  Support for a 3-slot PCI riser card  Support for both full leng th and low profile PCI cards Riser C provi des the follo[...]

  • Page 52

    2-20 General Description Network Controller NOTE: T o ensure EMC pr oduct regul ation com p liance, the system must be used wit h a shielded L AN cable. The mother boar d uses a dual-cha nnel Ethernet C ontroller and s upports 10Bas e-T/100Base - TX/1000Base -T netw ork subsyste ms. The network co ntroller sup port s the following features:  64-[...]

  • Page 53

    General Description 2-21 Remote Management Card (RMC) Server managem ent is concentrate d in the Remote M anagement C ard (RMC). The RMC and associated circuitry are powere d from a 5Vdc standby voltage, which remains active when system power is switched off, but the ac pow er source is still on and connected. The RMC supp orts the NEC Di anaScope,[...]

  • Page 54

    2-22 General Description DEGRADA TION FEA TURE The degradation featur e automatically isolates a failed D IMM or processor to assure contin uous operation of the server when the POST (Power On Self-T est, self-diagnosis program after power on) detects such a DIMM or proces sor . NOTE: The degra dation feature is only available when at least two DIM[...]

  • Page 55

    General Description 2-23 SYSTEM SECURITY T o help prevent unautho rized entry or use of the system, the system includ es a full lockable fron t bezel and Server Manageme nt software that m onitors the front bezel intrusion switch. Security with Mechani cal Locks and Monitoring T o unlock the bezel, insert the key in the loc k and turn the lock coun[...]

  • Page 56

    2-24 General Description Using Passwords Y ou can set either the u ser password, t he supervisor pass word, or bot h passwords. If only the use r password is set, you:  Must enter the user passwo rd to enter BIOS Setup.  Must enter the user password to boot the server if Password on Boot is enabled in the BIOS Setup.  Must enter the user p[...]

  • Page 57

    General Description 2-25 Summary of Sof tw are Security Features The table below lists the software security feat ures and descri bes what prot ection each of fers. In general, to enable or set the features listed here , you must run the BIO S Setup and go to the Security Subsystem Group, menu. The table also refers to the Setup utility . Software [...]

  • Page 58

    2-26 General Description Feature Description Control access to the system other than BIOS Setup: set user password T o control access to usin g the system, set a user password and enable it through Setup. T o disable a pass word, change it to a blank entry in the Change Password menu of the User Pass word Option menu found in the Security Subsyst e[...]

  • Page 59

    General Description 2-27 NEC EXPRESSBUILDER The CD-ROM that comes with the server contains a setup utility called "NEC EXPRESSBUILDER." The major functions of t he NEC EXPRESSBUILDER are:  T o install the Operating System. "Express Setup" helps you to install the W indows Operatin g System. (See Chapter 5)  T o diagnose th[...]

  • Page 60

    2-28 General Description NEC ESMPRO The NEC ESMPRO is server m anagement soft ware that runs on t he OS. The NEC ESM PRO includes the NEC ESMPRO Manager for the server monitoring terminal and the NEC ESMPRO Agent fo r the serv er . NOTE: For details of major functi ons of the NEC ESMPRO, system configuration and setups with the NEC ESMPRO, see Chap[...]

  • Page 61

    General Description 2-29 USING YOUR SERVER This section desc ribes basic operati ons of the server i ncluding how to use devices such as t he floppy disk drive an d the CD-ROM drive. See Appendix B for notes o n using the fl oppy disk, CD-ROM, and accessories including the keyboa rd and the mouse. Front Bezel Remove the front bezel to power on/of f[...]

  • Page 62

    2-30 General Description 3. Slide the front bezel to the le ft a little to rem ove the tab from the fram e and then remove the front bezel fr om the server . T o install the front bezel, latch the tab at the le ft side of the front bezel on the server frame. After the installation, lock the front bezel by using t he key for security . 1 2 Ta b Fram[...]

  • Page 63

    General Description 2-31 POWER Switch Use the POWER switch to turn on/off the server . Power On Press the POWER switch on the fr ont of the computer c hassis. The POWER LED lights in gree n. IMPORT ANT :  If the power cord is conne cted to a power control device such as a UPS (Uninterruptive Power Supply), make sure that th e power control de vi[...]

  • Page 64

    2-32 General Description POST POST (Power On Self-T est) is the self-diag nosti c program st ored in the system memory . When you power on the serv er , th e system automatically runs PO ST to check the mother board, ECC mem ory module, CPU m odule, keyboard, an d mouse. POST also displays m essages of the BIOS setup utility , such as the start-up [...]

  • Page 65

    General Description 2-33 POST Execution Flow The following describes the p rogress of POST in the chronological order . IMPORT ANT :  Do not m ake key entries or perform mouse operations w hile POST is in progress.  Some system configurations may display the message "Press Any Key" to prom pt a key entry . This me ssage is driven by[...]

  • Page 66

    2-34 General Description 4. POST displays SCSI ID numbers use d by the connecte d SCSI devices o n the screen. 5. After a few seconds, POST displays the following message prompting you to launch the BIOS setup utility , SETUP , stored in the system memory of the server . This message appears at bottom left on t he screen. Press <F2> to enter [...]

  • Page 67

    General Description 2-35 POST Error Messages When POST detects an error , it displays an error message on the display unit screen. See Chapter 8 for POST error codes. IMPORT ANT : T ake a note on the m essages displayed before consulting with your service repr esen tative. Alarm messages are useful inform ation for maintenance. Power Off Follow the[...]

  • Page 68

    2-36 General Description Identification of Servers (UID Switch) An "UID (Unit ID) LED" is provided on the front pa nel and rear panel . If more t han one server i s mounted in a si ngle rack, the LE D identifies the se rver you are goin g to maintain. The UID LED goes on when the UI D (Unit ID) switch on the front panel is pressed . It go[...]

  • Page 69

    General Description 2-37 Floppy Disk Drive The server is provided with the 3.5-inch floppy di sk drive on its front to write/read data to/from a floppy disk. The server supports the following 3.5-in ch floppy disks:  2HD floppy disk (double-sided high-densit y track type) Stores data of 1. 44MB.  2DD floppy dis k (double-sided double-density [...]

  • Page 70

    2-38 General Description NOTE: Use of the floppy dis k The floppy di sk is an im portant data sto rage media with delicate structure and requires care. Keep the following notes in mind to use it:  Insert the floppy disk into the flop py disk drive gently as far as it goes.  Attach the label to the correct position .  Do not writ e anything[...]

  • Page 71

    General Description 2-39 CD-ROM Drive The server is provided with the CD-ROM drive on its front to read data from a CD-ROM (read-only compact disk). The CD-ROM provi des large r and faster data read than the fl oppy disk. CAUTION Observe the following inst ructions to use the server safel y. Failure to follow these instructions may ca use a fire, p[...]

  • Page 72

    2-40 General Description 5. As shown in the figure below , hold the tray with a hand and press the CD-ROM with fingers of ano ther hand to make the hole of the CD-ROM fit to the rotor at the center of the tray . 6. Push the front of the tray ligh tly to retract it into the drive. IMPORT ANT : If a noisy soun d in driving the CD-RO M drive occurs af[...]

  • Page 73

    General Description 2-41 After taking out the CD-ROM, return the tray into the drive. When you fail to eject the CD-ROM tray with the Eject button and take out the CD-ROM from the server , fo llow the procedure below . 1. Press the POWER switch t o power off the serv er . (The POWER LE D goes of f.) 2. Insert a metal pin of ap proximately 1.2 mm in[...]

  • Page 74

    2-42 General Description NOTE: Use of the CD-ROM Keep the following notes in mind to use the CD-ROM for the server:  For the dis k which doe s not conf orm to the CD st andard, t he playback of suc h a disk with t he CD drive is no t guarantee d.  Do not drop the CD-RO M.  Do not place anything on the C D-ROM or bend the CD-ROM.  Do not[...]

  • Page 75

    Chapter 3 Setting Up Y our Server This chapter describes how to set up the server a ppropriate for you r system, on a step-by-step basis.[...]

  • Page 76

    3-2 Setting Up Y our Server SETUP FLOW Follow the flowchart below to set up the server . Selecting the server site Select a suitable site for the server . Assemble the 19-inch rack assembly . Unpacking the system Unpack the server and accessories from the chipping carton box. Installin g the server Install the server into the rack assembly . Connec[...]

  • Page 77

    Setting Up Y our Server 3-3 SELECTING SER VER SITE T o use the serv er , install it on a standard EIA 19-inch rack assembly . Refer to the documentation attach ed to the rack or contact your servi ce representative for the installation of the server on th e rack. W A RNI NG Observe the following instructions to us e the server safely. Failure to fo[...]

  • Page 78

    3-4 Setting Up Y our Serv er Do not install the rack in the places listed below . Installing the rack or m ounting the server on the rack in such a place may cause som e malfunction to occur .  Narrow space fr om which devices cannot be p ulled out f rom the rack c ompletely  Place that cannot bear the total weights of the rack and devices mo[...]

  • Page 79

    Setting Up Y our Server 3-5 UNP ACKING THE SYSTEM When you receive your system , inspect the shipping containers prior to unpa cking. If the shipping boxes are dam aged, note the dam age, and if possi ble, p hotograph i t for reference . After rem oving the contents of the containers, kee p the cartons and the packing materials. If the contents app[...]

  • Page 80

    3-6 Setting Up Y our Server Restricted Access Location The server is intended for installation in a restricted access location, m ounted above a non- combustible material. ESD Precaution An electrostatic di schar ge (ESD) can dam age disk drives, option boards, and othe r component s. Y ou can provide some ESD protection b y wearing an antistatic w[...]

  • Page 81

    Setting Up Y our Server 3-7 Inst allation Procedure for NEC Rack/Third V endor's Rack This server can be installed in either the NEC rack or a third vendor's rack. T ake the following procedure to install the server in th e rack: IMPORTANT: When installing the op tional cable arm, see the instruction manual provid ed with the cable arm. P[...]

  • Page 82

    3-8 Setting Up Y our Server Only the inner rails remain screwed to the server when the rail assemblies have been removed. IMPORTANT: The removed rail assemblies are to be installed on the inner rails later . T o install each rail assembly on the correct inner rail, make a mark on the assemblies. Similarly , when installing more than one server , di[...]

  • Page 83

    Setting Up Y our Server 3-9 Inst alling the Core Nut s Install three core nuts on the front of the rack fo r each of the right and left sid es and also two core nuts on the rear of the rack fo r each of the ri ght and left si des. Install three c ore nuts in 1U (t he minimum unit of rack hei ght). Three slots (angle holes) ar e opened per 1U of a r[...]

  • Page 84

    3-10 Setting U p Y our Server Inst alling the Rail Assemblies Make sure of the right side rail assembly or the left one when installing it. See the figure below . 1. Loosen a screw securing the rail assem bly . 2. Align the front and rear frames of rail assem bly to the location where the core nuts are installed. Locate the rail assembly so that th[...]

  • Page 85

    Setting Up Y our Server 3-1 1 Inst alling the Server CAUTION Observe the following instructions to us e the server safely. Failure to follow these instructions may cause a fire, pers ona l injury, or property damage. See pages 1-3 to 1-8 for details.  Do not lift the server only by a single person.  Do not pinch your finger with mechanical co[...]

  • Page 86

    3-12 Setting U p Y our Server 2. At least two persons are required to insta ll the serv er . Securely hold the server and install it in the rack. Firmly fit the inner rails on the sides of the server into the rail assem b lies that are installed on the rack, and then slowly push th e server into the rack. If the server is locked on its way into the[...]

  • Page 87

    Setting Up Y our Server 3-13 Securing the Server 1. Push the server into the rack as far as it will g o. 2. T ig hten the right and left captive thumb screws on the front panel to secu re the server to the rack. 3. Install the front bezel. This completes the installing of the serv er . Captive thumb screws[...]

  • Page 88

    3-14 Setting U p Y our Server Removing the Server from the Rack Assembly The server shoul d be rem oved from the rac k by at least two persons. W A RNI NG Observe the following instructions to us e the server safely. Failure to follow these instructions may result in death or serious p ersonal injury. See pages 1-3 to 1-8 for details.  Do not li[...]

  • Page 89

    Setting Up Y our Server 3-15 5. Hold the handle and pull out th e server from the rack slowly and carefully . The server clicks to be latched. 6. Pull out the server from the rack with the right and left release lever pressed to release the latch. IMPORT ANT :  Pull out the server slowly holding th e bottom of the server by at least two person s[...]

  • Page 90

    3-16 Setting U p Y our Server CONNECTING PERIPHERAL DEVICES Connect periphe ral devices to the ser ver . The server i s provided wit h connectors for wide variet y of peripheral devices on its front and rear. The figure on the next page illustrates available peripheral de vices for the se rver in the standar d configurati on and locations o f the c[...]

  • Page 91

    Setting Up Y our Server 3-17 Device w ith the serial inte rface (e.g., Management PC) *2 Keyboard Mouse Hub (multiport repeater) *1 Any USB keyboard and mou se are not supported. *2 A leased line cannot be connected directly to this conne ctor . The console of a mana gement PC ca n be connecte d to only serial port B. (BIOS setup required.) *3 Use [...]

  • Page 92

    3-18 Setting U p Y our Server CONNECTING POWER CORD Connect the prov ided powe r cord to th e server . W A RNI NG Observe the following instructions to us e the server safely. Failure to follow these instructions may result in death or serious p ersonal injury. See pages 1- 3 to 1-8 for details.  Do not hold the power plug with a wet hand.  D[...]

  • Page 93

    Setting Up Y our Server 3-19 T o co nnect the pow er cord fro m the server to an uninterrup tive power supply (UPS), use service outlets on the rear of the UPS. The UPS service outlets are categorized i nto two groups: SWITCH OUT and UN-SW ITCH OUT . (They may be cal led "OUTPUT1" an d "OUTPUT2".) T o con trol power supply with [...]

  • Page 94

    3-20 Setting U p Y our Server TURNING ON THE SERVER T u rn on the server and follow the on-screen instructions for setup. IMPORT ANT : Before turning on the server:  Some optional boards require setups with the SETUP utility before installation. If the server has a PCI board with the PCI-to-PCI bridge installed, the SETUP utility is enabled to l[...]

  • Page 95

    Setting Up Y our Server 3-21 The POWER LED on the front of the server com es on. In a few seconds, the NEC logo a ppears on the sc reen and the Power On Self-T est (POST) begins. The POST runs automatically when you power on the server or reset it with a keyboard operation ( Ct rl + Alt + Delete ). The POST runs diagnostics, initializes the serv er[...]

  • Page 96

    3-22 Setting U p Y our Server INST ALLING OPERA TING SYSTEM See Chapter 5 for installing the Microsoft W indows Server 2003 or Micro soft W indows 2000 operating systems. T o install the oth er operating system listed above, c ontact your service representative. IMPORT ANT : Before installing the operating system, adjust the system date and time by[...]

  • Page 97

    Chapter 4 Configuring Y our Server Configuration and setup utilities are used to change your system configuration. Y ou can configure your system, as well as option boards you may add to your system, using the BIOS Setup Utility . Several unique system parameters are configured using the BIOS Setup, which is stored in the system FLASH memory . The [...]

  • Page 98

    4-2 Configuring Y our Server St arting SETUP Utility Powering on t he server starts POST (Power On Se lf-T est) and displays its check results. If the NEC logo is displayed, press Esc . After a few seconds, the following message appears at bottom left on the sc reen. Press <F2> to enter SETUP Press F2 to start the SETUP utility and display it[...]

  • Page 99

    Configuring Y our Server 4-3 Description on On-Screen Items and Key Usage Use the following keyboard keys to work with th e SETUP u tility . (Key functions are also listed at the bottom of the screen.) * The menus displayed in gray indicates the information only or unchangeable secured by BIOS passw ord. Cursor ( ↑ , ↓ ) : Selects an item on th[...]

  • Page 100

    4-4 Configuring Y our Server Menu and Parameter Descriptions The SETUP utility has th e following six major menus :  Main  Advanced  Security  Server  Boot  Exit T o set minute functio ns, select a subm enu from the ab ove menus. The f ollowing descri bes available funct ions and param eters, as well as the factory-set, for each m[...]

  • Page 101

    Configuring Y our Server 4-5 Main Option Parameter Desc ription Y our Setting System T ime HH:MM:SS Set the system time. System Date MM/DD/YYYY Set the system date. Legacy Floppy A Disabled 360Kb 5 1 / 4 1.2MB 5 1 / 4 720Kb 3 1 / 2 [1.44/1.25MB 3 1 / 2 ] 2.88MB 3 1 / 2 Set the settings of floppy disk drive A (standard configuratio n). Legacy Floppy[...]

  • Page 102

    4-6 Configuring Y our Server Primary IDE Master/Primary IDE Slave/Secondary IDE Master/Secondary IDE Slave/Serial A T A Channel 0 Master/ Serial A T A Channel 1 Master Correspondence between the m enu items and d evices:  Primary IDE Master: A T A hard disk drive 1 (option)  Primary IDE Slave: A T A hard disk drive 2 (option)  Secondary ID[...]

  • Page 103

    Configuring Y our Server 4-7 Processor Settings Option Parameter Desc ription Y our Setting Processor Retest [No] Ye s If yes, BIOS will clear historical processor status and retest the processor on the next boot. Processor S peed nnn GHz Displays clock speed for the processor . (View only) Processor 1 CPUID Numeral Disabled Displays CPU ID for pro[...]

  • Page 104

    4-8 Configuring Y our Server Advanced Option Parameter Desc ription Y our Setting Memory Configuration – Displ ays Memory Configuration submenu. PCI Configuration – Displa ys PCI Configuration submenu. Peripheral Configuration – Displ ays Peripheral Configuratio n submenu. Advanced Chipset Control – Displays Advanced Chipset Control submenu[...]

  • Page 105

    Configuring Y our Server 4-9 Memory Configuration Option Parameter Desc ription Y our Setting System Memory nnn KB Indicates the total capacity of the basic memory . (View only ) Extended Memory nnnnnnn KB Indicates the total capa city of the extended memory . (View only) DIMM Group #1 - #4 Normal Disabled Not installed Indicates the current memory[...]

  • Page 106

    4-10 Co nfiguring Y our Server PCI Configuration – Embedded SCS I submenu Option Parameter Desc ription Y our Setting SCSI Controller [Enabled] Disabled Enables or disables the onboard SCSI controllers. Option ROM Scan [Enabled] Disabled If Enabled, initialize device expansion ROM. [ ]: Factory-set – Embedded NI C (Dual Gbit) s ubmenu Option Pa[...]

  • Page 107

    Configuring Y our Server 4-1 1 Peripheral Configuration IMPORTANT: Note that the i nterrupt an d/or base I/O a ddress are not overlapped with others. If the value set for the in terrupt or base I/O address is used in another res our ce, the yellow asterisk (* ) appears. Reset any item with the yellow asterisk properly . Option Parameter Desc riptio[...]

  • Page 108

    4-12 Co nfiguring Y our Server Advanced Chip set Control Option Parameter Desc ription Y our Setting Enable Multimedia Ti me r [No] Ye s S pecify whether the system supports the multimedia timer feature. W ake On LAN/PME Disabled [Enabled] S pecif y whether the remote power-on function through embedded NIC, PCI devices in slots 1 to 5 is enabled or[...]

  • Page 109

    Configuring Y our Server 4-13 Security The Security m enu appears if y ou move th e cursor to the position of "Security ." Press Enter on "Set Su pervisor Password" or "Set User Password ," to display the following scree n. Enter the passwo rds on the dialo g box. Passwor ds may have up t o eight characters incl uding [...]

  • Page 110

    4-14 Co nfiguring Y our Server Option Parameter Desc ription Y our Setting Set Supervisor Password Up to eight alphanumerics When the <Enter> key is pressed, the user is prompted for a password; press ESC key to abort. Once set, this can be disabled by setting it to a null string, or by clearing password jumper on system board (refer to Confi[...]

  • Page 111

    Configuring Y our Server 4-15 Server Option Parameter Desc ription Y our Setting Syst em Management – System Management submenu is displayed. Console Redirection – Console Redirection submenu is displayed. Event Log Configuration – Event Log Configuration submen u is displayed. Assert NMI on PERR Disabled [Enabled] S pecify whether to support[...]

  • Page 112

    4-16 Co nfiguring Y our Server Option Parameter Desc ription Y our Setting Post Error Pause Disabled [Enabled] S pecify whether to stop the POST once at the end of POST if an error occurs during the POST . AC-LINK S tay Off [Last S tate] Power On S pecify the state of power when the AC power to the server is turn off once and then on. Power On Dela[...]

  • Page 113

    Configuring Y our Server 4-17 System Management Submenu Option Parameter Desc ription Y our Setting BIOS V ersion – Displays the current BIOS version. (View only ) IPMI S pecification Ve r s i o n – Displays IPMI specification version. (View only ) BMC Device ID – Displays BMC device ID. (View only) BMC Device Ve r s i o n – Displays BMC de[...]

  • Page 114

    4-18 Co nfiguring Y our Server Boot If you move the cursor to the position of "Boot," the Boot menu appe ars, which is used to set the boot priori ty . The factory-defa ult boot or der is liste d below . 1. CD-ROM drive 2. Remova ble Devices 3. Hard Drive 4. IBA GE Slot 0200 v1216 5. IBA GE Slot 0209 v1216 The server searc hes for devices[...]

  • Page 115

    Configuring Y our Server 4-19 SCSI BIOS (SCSI Select ) The SCSI Select utility is provided to configure th e SCSI controller on the mother board (or the SCSI controller on an option al board). This u tility may be started with a simple key operation while POST is in progress and requires no specific start-up disk. Using SCSI Select Utility Use the [...]

  • Page 116

    4-20 Co nfiguring Y our Server Running the Utility T o run th e utility , perform the following procedures: 1. Power on the server . The following message appears while POST is in progress. IMPORT ANT : The message appears for each additional SCSI controller . Adaptec SCSI BIOS Vxxx xxxxx (c) 2000 Adaptec, Inc. All Rights Reserved  Press &[...]

  • Page 117

    Configuring Y our Server 4-21 Exiting the Utility T o exit th e utility , press Esc until a message prompts you to exit (if you chang ed any setting, you are prompted to save t h e changes before you e xit). Configure/View SCSI Controller Settings The Configure/V iew Host Adapter Settings has the fo llowing menu items and parameters. Read descripti[...]

  • Page 118

    4-22 Co nfiguring Y our Server  SCSI Device Configuration Move the cur sor onto "SCS I Device Confi guration" and p ress Enter to display the submenu. The following table lists submenu items, available param eters, and descriptions. IMPORT ANT : Select a parameter for eac h submenu it em on a per - SCSI ID basis. V erify the SCSI ID of[...]

  • Page 119

    Configuring Y our Server 4-23  Advanced Configuration Move the cur sor onto "Ad vanced Configurat ion" and press Enter t o display t he submenu. The following table lists submenu items, available parameter , and descriptions. Submenu item Parameter Description Reset SCSI Bus at IC Initialization [Enabled] Disabled Select "Enabled&[...]

  • Page 120

    4-24 Co nfiguring Y our Server SCSI Disk Utilities This utility scans the SCSI bus fo r SCSI devices, reports a desc ri ption of each device. R un these utilities before configuring SCSI dev ices. T o enter the u tility , select "SCSI Disk Utilities" on the Options menu. The SCSI ID sca n begins dis playing the m essage as shown belo w . [...]

  • Page 121

    Configuring Y our Server 4-25 Configuring SCSI Controller on Optional Board T o co nfigure S CSI devi ces conne cted to an o p tional SCSI controller board, use the SCSI BIOS utility provided with th e optional SCSI controller board. Refer to the manual that comes with the optional SCSI con troller board for details. When the server has multiple SC[...]

  • Page 122

    4-26 Co nfiguring Y our Server RAID BIOS The RAID (Redundant Array of Inexpensive Devices) option available for your system is N8103- 80F/81F/86F RAID controlle r boards which gi ve your system the added security of fault tolerance. If you want to change the RAID level or add add itional hard disk drives to the array , use the RAID configuration ut[...]

  • Page 123

    Configuring Y our Server 4-27 RAID CONFIGURA TION This section describes how to use the internal h ard disk drives in the disk array R AID configu ration. T o use an external ha rd disk drive in a disk array , the optional di sk array cont roller and t h e additional disk drive are necessary . Refer to th e manual of the optional disk array control[...]

  • Page 124

    4-28 Co nfiguring Y our Server Inst alling the Hard Disk Drives Install the two or more SCSI hard disk drives to your server . Refer to Chapter 9 for detail. IMPORT ANT : Use two hard disk drives of the same revolution. In addition, u se two hard d isk drives of th e same capacity if you are going to configure RAID1. Enabling RAID Feature by SCSISe[...]

  • Page 125

    Configuring Y our Server 4-29 4. Select [Disable d] of Host RA ID on Confi guration m enu and press Enter . 5. Change it to [Enabled]. 6. Press Esc . T he confirmation message [Sa ve Changes Mode?] appears. Select [Y es]. 7. Press Esc to return to the Options menu. 8. Select [Configure/V iew HostRAID] and press Enter .[...]

  • Page 126

    4-30 Co nfiguring Y our Server Main Menu When you select [Config ure/V iew HostRAID Setti ngs] , the Main Men u as shown belo w appears upon compl etion of device scan. Main Menu Display ■ ID - Indicates SCSI ID of hard disk drive or ID of array . ■ T ype - Indicates RAID level for the array , and availabl e disk drive that is not in the array [...]

  • Page 127

    Configuring Y our Server 4-31 When you select the array on Main Menu, the detailed in formation of the hard disk drives in array is displayed. Det a iled indications ■ ID - Indicates SCSI ID of hard disk drive that configures the arr ay ■ T ype - Indicates RAID level for the array .  S triped (R0) - Array configured i n RAID0  Mirrored (R[...]

  • Page 128

    4-32 Co nfiguring Y our Server RAID Configuration by SCSISelect Utility Creating Arrays T ake the fo llowing proced ures to create an array . Requirement s Before creating arrays, m ake sure the disks for the array are connected and installed in your system. 1. Start the SCSISelect Utility. Select [Configure/V iew HostRAID Settings] from Options me[...]

  • Page 129

    Configuring Y our Server 4-33 3. Select an RAID type in [Select RAID T ype] win dow and press Enter . Put a cursor to the selected item, anothe r window opens indica ting the minimum and maximum num ber of disks to create an array a n d a message fo r assigning a spare disk. NOTE: For setting of RAID, see "Creating RAID0 Array" or "C[...]

  • Page 130

    4-34 Co nfiguring Y our Server Creating RAID0 Array T o create a RAID0 array: 1. Select [RAID-0] on [Select RAID T ype] window . 2. Use the cursor key to move the focus to the desi red hard disk drive and determine it by Sp ace , and th en press Enter . An [X] m ark is placed next t o the selected hard disk drive. 3. Select the desired stripe size [...]

  • Page 131

    Configuring Y our Server 4-35 6. Select [Y es] for the message [Create Array? ] and press Enter. Selecting [No] terminates creating an array and returns to the main menu. 7. Select [Y es] for the message [Are y ou sure?] and press Enter. Selecting [No] terminates creating an array and returns to the main menu. 8. Press Esc when the message [Build C[...]

  • Page 132

    4-36 Co nfiguring Y our Server Creating RAID1 Array T o create a RAID1 array , perform either of t he followings:  Create a new RAID1 array .  Migrate to RAID1 array using the data stored in an ex isting single disk. (Migration) Creating RAID1 array using the existing single hard disk drive is called "migration". In migration, the s[...]

  • Page 133

    Configuring Y our Server 4-37 IMPORT ANT :  T o migrate the boot disk that contai ns an OS, refer to the "Migration in NEC Express5800 W indows".  Make sure the copy source a nd co py destination. If th ey are incorrect, the data will no longer be restored. 3. Enter the desi red RAID Nam e in [Assign RAID Nam e] window . IMPORT ANT [...]

  • Page 134

    4-38 Co nfiguring Y our Server Creating RAID10 Arra y 1. Select [RAID-10] on [Select RAID T ype] window and press Enter . 2. Use the cursor key to move the focus to the desi red hard disk drive and determine it by Sp ace , and th en press Enter. An [X] m ark is placed next t o the selected hard disk drive. 3. Select the desired stripe size and pres[...]

  • Page 135

    Configuring Y our Server 4-39 5. The message "Do you want to make this array as bootab le?" to prompt you to specif y the boot pri ority of the ne w array ap pears. Sel ect [YES] to specify , or [NO] to ignore, a nd then press Enter . 6. Select [Y es] for the message [Create Array? ] and press Enter. Selecting [No] terminates creating an [...]

  • Page 136

    4-40 Configuring Y our Server Deleting Arrays T o delete an array: IMPORT ANT : Back up th e data in the hard disk drive of an array before you delete it. Otherwise, all data on the array is lost. Deleted arrays cannot be restored. 1. On the main menu, move cursor to select the array you wish to delete and press Enter. 2. Press D on the screen show[...]

  • Page 137

    Configuring Y our Server 4-41 4. <RAID0> [Deleting info rmation] wi ndow appears. Select the hard disk drive you wish to delete its partition or boot block, or select [Non e], then press Enter . <Example> Drive ID 0: Data in drive 0 is entirely erased. Data in drive 1 is reserved. Drive ID 1: Data in drive 1 is entirely erased. Data in [...]

  • Page 138

    4-42 Co nfiguring Y our Server Creating Sp are Disk Up to two s pare disks can be assi gned for o ne channel. Spare disk is available fo r RAID1 and RAID10 (spa nning of R AID1) only . NOTE: Spare disk must ha ve lar ger ca pacity than the hard disk drives configuring th e array . If the hard di sk drives in t he array have 73GB or lar ger and the [...]

  • Page 139

    Configuring Y our Server 4-43 5. On the mai n menu, make sure that the type of selected hard disk drive is c h anged to "Spare", and it s status "Optim al". T o unassign a spare disk, take the sam e st eps from 1 to 4 e xcept for selecting "Delete Spare" instead of "Add Spare". Boot Priority T o specify boo t[...]

  • Page 140

    4-44 Co nfiguring Y our Server CONFIGURING MOTHER BOARD JUMPERS W ith the pre-installed SETUP u tility , you can set desired passwords to pro tect the data stored in the server against access from unauthori zed users. When you for g et the passwords, however , you may want clear them . The following desc ribes how t o clear these passwords. Y ou ca[...]

  • Page 141

    Configuring Y our Server 4-45 The following describe the cleari ng procedure. W A RNI NG Observe the following instructions to us e the server safely. Failure to follow these instructions may result in death or seri ous personal injury. See pages 1-3 to 1-8 for details.  Do not disassemble, repair, or alter the server.  Do not remove the lith[...]

  • Page 142

    4-46 Co nfiguring Y our Server (This page is intentionally left b lank.)[...]

  • Page 143

    Chapter 5 Inst alling the Operating System with Express Setup This section describes information on using Express Setup to install and conf igure the following operating systems to the server .  Microsoft® Windows Server  2003 R2 Standard Edition / Microsoft® W indows Server  2003 R2 Enterprise Edition / Micro soft® W indows Server  [...]

  • Page 144

    5-2 Installing the Operating System with Express Setup About Express Setup "Express Setup" helps you to install the W indows Op erating System. The setup automatically configures the RAID system and installs the Operating System and some manageme nt software. IMPORT ANT : Executing the Express Setup erases a ll data on the hard disk drive[...]

  • Page 145

    Installing the Operating System with Express Setup 5-3 Microsof t Windows Server 2003 This subsecti on provides inf ormation on in stalling Micros oft® W indows Server  2003 in the Server . Read instruction in this section before proceeding the installation. NOTES:  Express Setup does not support the in stallation of W indows Server 2003 x64[...]

  • Page 146

    5-4 Installing the Operating System with Express Setup Optional Board Supported by NEC EXPRESSBUILDER NEC EXPRESSBUILDER CD-ROM attached to you r system support s the follo wing optional boards; NOTE: If you want to instal l the other boards by usi ng a driver flo ppy disk ("OEM-FD for Mass stora ge device"), except ones listed below , se[...]

  • Page 147

    Installing the Operating System with Express Setup 5-5 Windows Server 2003 Express Setup ca n install Windo ws Server 2003 operating system . Confirm belo w notes before installing the W i ndows. IMPORTANT:  Before starting the installation, complete all the process of adding the optional device an d the setup of Express server mainframe (BIOS a[...]

  • Page 148

    5-6 Installing the Operating System with Express Setup Creating Partition Size The size for the partition that the system is to be installed can be calculated from the following formula. Size necessary to install the system + Paging File Size + Dum p File Size + Application Size Size necessary to install the system = 2900MB (Only W indows Serv er 2[...]

  • Page 149

    Installing the Operating System with Express Setup 5-7 Re-installing to the hard disk which ha s been upgraded to Dynamic Disk Y ou can not re-install W indows Server 2003 with the cu rrent partition of the hard disk drive upgraded to Dynam ic Disk kept remained. If you want to keep the current partition remained, see App endix D to re-install the [...]

  • Page 150

    5-8 Installing the Operating System with Express Setup The Flow of Setup This section shows the fl ow of the Expr ess setup. New File Ye s Confirme d : Process that proc eeds automatical ly : Process that needs t o input or select Do y ou wan t to use th e p arame ters fil e in ord er to set up the Express server ? Read notes and restri ctions Inse[...]

  • Page 151

    Installing the Operating System with Express Setup 5-9 Inst alling the Window s Server 2003 Express Setup pr oceeds the setup by specifying t he necessary information on the wizard. Y ou can also save the setup inform ation created on th e wizard in a flop py disk as a setu p file. NOTE: Prepare a floppy disk to use as Configuration Disk if you wan[...]

  • Page 152

    5-10 Installing the Operating System with Express Setup 7. If you select "Y es" at step 5, place a floppy disk i nto the floppy disk drive mounted on the server . If not, go on the next step. NOTE: If you set the floppy disk at this step, do not r emove the floppy disk from the server until the message as removing the floppy disk appears.[...]

  • Page 153

    Installing the Operating System with Express Setup 5-1 1 10. Select the W indows family . Select "Microsoft W indows Server 2003 Standard Edition Microsoft W indows Server 2003 Enterprise Edition" catego ry . NOTE: If you sel ect "Skip" at step 8, this menu does not appea r . Go on the step 13. 11. Next, [Basic Information] wiza[...]

  • Page 154

    5-12 Installing the Operating System with Express Setup 12. Copy the m odules for the opti onal mass storag e driver . If you want to install the optional mass storag e driver , insert the floppy d isk attached to mass storage dri ver into the floppy disk drive and follow th e me ssage to operate the installation. NOTE: This function requires mount[...]

  • Page 155

    Installing the Operating System with Express Setup 5-13 NOTE: About MegaR A ID S torage Manager (he reinafter , refered to as "MSM") When N8103-91 bo ard is connected, Wi ndows Server 2003 Service Pack 1 or later is necessary to install MSM. When y ou try to install MSM, and the setting of whether to apply Service Pack is [No], the follow[...]

  • Page 156

    5-14 Installing the Operating System with Express Setup Inst alling and Setting Device Drivers Follow these steps to install and configu re the device drivers. PROSet PROSet is a utility that confirms the function of netwo rk contained in network driver . Utilizing PROSet enables the following items:  Confirm detailed information of the ad apter[...]

  • Page 157

    Installing the Operating System with Express Setup 5-15 Network Driver Specify the details of network driver . One standard network driver th at is mounted will be installed automatically , b ut the link speed and Duplex mode nee d to be speci fied manually . [When PROSet is not installed] 1. The [Local Area Connection Prop erties] dialog box appea[...]

  • Page 158

    5-16 Installing the Operating System with Express Setup Also, add or delete any protoc ols and services if necessary . Y ou can operate the process on the p roperty dialog box for local area network which can be appeared from [Network and D ial-up Connection]. NOTE: W e recommend you to add [N etwork Monitor] at [Adding Services]. [Network Mon itor[...]

  • Page 159

    Installing the Operating System with Express Setup 5-17 Inst allation of the Optional Network Board Driver 1. Start Device Manage r . 2. Click [Network adapters] and Double-Click [(Network Adap ter Name)]. [(Network Adapter Nam e) Properties] appea r s. NOTE: [(Intel(R) PRO/1000... )] is the nam e of On-Board adapter . All other names show the Opti[...]

  • Page 160

    5-18 Installing the Operating System with Express Setup Adapter Fault T olerance (AFT)/Adaptive Load Balancing (ALB) Adapter Fault T olerance (AFT) is a feature th at cr eates a group containing more than one adapter and automatically converts t he pr ocess of the working adapter to the other ada pter in the group when any trouble occurred on that [...]

  • Page 161

    Installing the Operating System with Express Setup 5-19 Inst alling SCSI Controller Driver (N8103-65F) If you utilize SCSI controller driv er (N8103-65F), insta ll it according to the following proce dure: 1. Start [Device Ma nager] from [S tart] menu → [Control Panel] → [Administrative T oo ls] → [Computer M anagement ]. 2. Double-clic k the[...]

  • Page 162

    5-20 Installing the Operating System with Express Setup Inst alling SCSI Controller Driver (N8103-75) If you utilize SCSI controller driv er (N8103-75), insta ll it according to the foll owing procedure: <In the case of use of Windows Server 2003 SevicePack1 or Windows Server 2003 R2> If you utilize SCSI controller driver (N810 3-75), update [...]

  • Page 163

    Installing the Operating System with Express Setup 5-21 Inst alling Disk Array Controller Driver (N8103-80F/81F) T o additionally install the N81 03-80F/81F in a system containi ng W indows Server 2003, conne ct the controller and take the following steps to install the driv er: <In the case of use of Windows Server 2003 SevicePack1 or Windows S[...]

  • Page 164

    5-22 Installing the Operating System with Express Setup Graphics Accelerator Driver Standa rd graphics accelerator drivers t hat are mounted will be installed a utomatically . The following is the procedure when it is neces sary to install manually . If you want to utilize optional Graphics Accelerator Driver board, follow th e doc ument attached t[...]

  • Page 165

    Installing the Operating System with Express Setup 5-23 A vailable switch options for Windows Server 2003 Boot.ini file. Many different switches will be ava ilable if you edit Boo t.ini file. For the available switch options, refer to the following information:  Microsoft Knowledge Base - Article ID: 833721 "A vailable switch options for th[...]

  • Page 166

    5-24 Installing the Operating System with Express Setup Setting for Solving Problems Setup the following issue in advance so that your computer can recover from any troub le precisely and as soon as possible when it should occur . Memory Dump (Debug Information) This section desc ribes the proce dures for collect ing memory d ump (debug inf ormatio[...]

  • Page 167

    Installing the Operating System with Express Setup 5-25 IMPORTANT: W indows Server 2003 x64 Editio ns  T o specify "Complete Memory Dump" to write the debug information is recommend ed. If the mounte d memory size is lar ger than 2GB, "C omplete Memory Dump" cannot be specified so that specify " Kernel Me mory Dump "[...]

  • Page 168

    5-26 Installing the Operating System with Express Setup 4. Specify "Com plete memory dump" and m odify [Dump fil e:] in the [W rite de bugging information] gr oup box. e.g. W rite the debug information in D drive write the file name "MEMOR Y .DMP". D:MEMOR Y .DMP 5. Click [Settings] on the [Performance] group box. The [Performa[...]

  • Page 169

    Installing the Operating System with Express Setup 5-27 Windows Dr . Wat son W indows Dr . W atson is a debugger for a pplication error s. If any application er ror is detected, Dr . W atson dia gnoses the server and logs dia gnostic inform ation (log). Follow t he procedure below and specify Dr . W atson to collect diagnostic information. 1. Click[...]

  • Page 170

    5-28 Installing the Operating System with Express Setup Network Monitor Utilizing Network Monitor helps you to investigate and manage with network trouble. T o utilize Network Monitor , you need to restart the system after the installation has completed, so we recommend to i n stall Netw ork Monitor before any net work troubl e may occur . 1. Point[...]

  • Page 171

    Installing the Operating System with Express Setup 5-29 Up dating the System - Installing Service Pack - IMPORT ANT : If you install W indo ws Server 2003 CD-RO M which contains Service Pack 1 to your syst em, you do not have to ap ply Service Pack 1 again. Update the system in the situation below:  Modified syst em configurati on.  Recovered[...]

  • Page 172

    5-30 Installing the Operating System with Express Setup Exceptional Setup This section e xplains how t o set up the serve r by the except ional way . Y ou usually do n ot have to do as follows. If you want to i nstall the othe r boards by using a drive r floppy disk ("OEM-FD for M ass storage device"), exce pt ones listed in Chapter 5, se[...]

  • Page 173

    Installing the Operating System with Express Setup 5-31 Microsof t Windows 2000 This subsection prov ides information on installing Microsoft® W indows® 2000 in the server . Read instruction in th is section before proceeding the installation. NOTE: If you install W indows 2000 w ithout using Express Setup, see Appendi x E. Inst allation Notice T[...]

  • Page 174

    5-32 Installing the Operating System with Express Setup Optional Board Supported by NEC EXPRESSBUILDER The NEC EXPRE SSBUILDER CD-R OM attached to y our system supp orts the follo wing optional boards; NOTE: If you want to instal l the other boards by usi ng a driver flo ppy disk ("OEM-FD for Mass stora ge device"), except ones listed bel[...]

  • Page 175

    Installing the Operating System with Express Setup 5-33 Windows 2000 Express Setup can install W indows 2000 operatin g system. Confirm below notes before installing the W indows. IMPORTANT:  Before starting the installation, complete all the process of adding the optional device an d the setup of Express server mainframe (BIOS and optio nal boa[...]

  • Page 176

    5-34 Installing the Operating System with Express Setup About Maintenance Partition (the area displayed as "MAINTE_P") The maintenance partition for serv er maintenance is reserved in the head of Hard Disk Drive (a partition of approx imately 55MB). This area is for saving some maintenance utilities. Do not delete the maintenance partitio[...]

  • Page 177

    Installing the Operating System with Express Setup 5-35 For example, if the m ounted memory size is 51 2MB, the partition size will be calculated by the above formula as follows: 1000MB + (512MB * 1.5) + (512MB + 12MB) + Applicatio n Size = 2292MB + Application Size Dividing into the partition of the recommended size into multiple disk s as written[...]

  • Page 178

    5-36 Installing the Operating System with Express Setup The Flow of Setup This section shows the fl ow of the Expr ess Setup. New File Ye s Confirme d : Process that proc eeds automatical ly : Process that needs t o input or select Do y ou wan t to use th e p arame ters fil e in ord er to set up the Express server ? Read notes and restri ctions Ins[...]

  • Page 179

    Installing the Operating System with Express Setup 5-37 Inst alling the Window s 2000 Express Setup pr oceeds the setup by specifying t he necessary information on the wizard. Y ou can also save the setup inform ation created on th e wizard in a flop py disk as a setu p file. NOTE: Prepare a floppy disk to use as Configuration Disk if you want to s[...]

  • Page 180

    5-38 Installing the Operating System with Express Setup 6. "NOTE" appears. Click [C onfirm] after reading that. NOTE: If som e operating system has been installed on the har d disk drive already , the message which ask s if you continue the in stallation appears. 7. If you select "Y es" at step 5, place a floppy disk i nto the f[...]

  • Page 181

    Installing the Operating System with Express Setup 5-39 8. Confirm or m odify the paramet ers of disk array configuration . NOTE: If you do not use disk array contro ller , go on the next step. If a Disk array c ontroller is connected to t h e server or the HostRAID is enabled, the [Configure R AID] dialogue-bo x appears. C onfirm the pa rameters, [...]

  • Page 182

    5-40 Installing the Operating System with Express Setup IMPORTANT:  Reserve the partition to install the OS more than the minimally required size.  If you select "Use Existing Array" at "New/Existing RAID Configuration", the info rmation included in the first partition (excluding maintenance partition) will all be formatte[...]

  • Page 183

    Installing the Operating System with Express Setup 5-41 12. Copy the m odules for the opti onal mass storag e driver . If you want to install the optional mass storag e driver , insert the floppy d isk attached to mass storage dri ver into the floppy disk drive and follow th e me ssage to operate the installation. NOTE: Y ou can use this fun ction [...]

  • Page 184

    5-42 Installing the Operating System with Express Setup Inst alling and Setting Device Drivers Follow these steps to install and configu re the device drivers. PROSet PROSet is a utility that confirms the function of network con tained in network driver . Be sure to install. Utilizing PROSet enables the following issues:  Confirm detailed inform[...]

  • Page 185

    Installing the Operating System with Express Setup 5-43 Network Driver [When PROSet is not installed] 1. Click S tart menu and click [ Network and Di al-Up Connect ion]. The [Network and Dial-Up Conn ection] dialog box appears . 2. Right-click [Local Area Connection] and clic k [Properties] from pop-up m enu. The [Local Area Connection Prop erties][...]

  • Page 186

    5-44 Installing the Operating System with Express Setup Optional Network Board Driver If you want to utilize optional Network Board (N8 104-86/88/1 1 1/103/109/1 12/1 13/1 15) install the driver store d in NEC EXPRESSB UILDER CD-ROM . Refer to the re-installat ion procedure described in Appendix F . Network Dri v er for ( N8104-86/88/ 11 1) [<CD[...]

  • Page 187

    Installing the Operating System with Express Setup 5-45 Inst alling SCSI Controller Driver (N8103-65F/75) If you utilize SCSI controller driv er (N8103-65F/7 5), inst all it according to the following procedure: 1. Start [Device Ma nager] from [S tart] menu → [Cont rol Panel] → [Admi nistrative T ools] → [Computer M anagement ]. 2. Double cli[...]

  • Page 188

    5-46 Installing the Operating System with Express Setup Inst alling RAID Controller Driver (N8103-80F/81F) T o add itionally install the N81 03-80F/81F in a system containing W indo ws 2000, connect the controller and take the following steps to install the driver: 1. When the [F ound New Ha rdware W izard] dialog box a ppears, click [Ne xt]. 2. Wh[...]

  • Page 189

    Installing the Operating System with Express Setup 5-47 A vailable switch options for Windows 2000 Boot.ini file. Many different switches will be available if you edit Boo t.ini File. For the available switch options, refer to the following information:  Microsoft Knowledge Base - Article ID: 170756 "A vailable Switc h Options f or the W in[...]

  • Page 190

    5-48 Installing the Operating System with Express Setup Setting for Solving Problems Setup the following issue in advance so that your computer can recover from any troub le precisely and as soon as possible when it should occur . Memory Dump (Debug Information) This section desc ribes the proce dures for collect ing memory d ump (debug inf ormatio[...]

  • Page 191

    Installing the Operating System with Express Setup 5-49 IMPORTANT:  T o specify "Complete Memory Dump" to write the debug informati on is recommended . If the mount ed memory size is lar ger than 2GB, "Com plete Memory Dump" cannot be speci fied so that specify "Kernel Memory Dump" instead.  Specify the drive whe[...]

  • Page 192

    5-50 Installing the Operating System with Express Setup Windows 2000 Dr . Wat son W indows 2000 Dr . W atson is a debugger for applicati on errors. If any applicati on error is detected , Dr . W atson diagn oses the server an d logs dia gno stic information (log). Follow the procedure below and specify Dr . W atson to collect diagn ostic informatio[...]

  • Page 193

    Installing the Operating System with Express Setup 5-51 Network Monitor Utilizing Network Monitor helps you to investigat e and manage with network trouble. T o utilize Network Monitor , you need to restart the system after the installation has completed, so we recommend to i n stall Netw ork Monitor before any net work troubl e may occur . 1. Poin[...]

  • Page 194

    5-52 Installing the Operating System with Express Setup Up dating the System - Installing Service Pack - IMPORT ANT : This system does not support W indow s 2000 Service Pack 1 - 3. If you install W indow s 2000 CD-ROM which contains Service Pack 4 to your system, you do not ha ve to apply Service Pack 4 ag ain. Update the system in the situation b[...]

  • Page 195

    Installing the Operating System with Express Setup 5-53 Exceptional Setup This section e xplains how t o set up the serve r by the except ional way . Y ou usuall y do not have t o do as follows. If you want to i nstall the othe r boards by using a drive r floppy disk ("OEM-FD for M ass storage device"), exce pt ones listed in Chapter 5, s[...]

  • Page 196

    5-54 Installing the Operating System with Express Setup HostRAID The followin g explains the overview of H ostRAID and t he setup procedure . Overview of HostRAID HostRAID pr ovides RAID feat ure through the onboard serial A T A or SCSI interface in your system. HostRAID co nsists of the drive r that controls di sk arrays and "A daptec S torag[...]

  • Page 197

    Installing the Operating System with Express Setup 5-55 Notes The following ex plains general notes on H ostRAID: <SCSI HostRAID>  Only a hard disk dri ve can be connected to a channel with which HostRAID is enabled through SCSI BIOS.  T o connect a device ot her than a hard di sk drive, disable HostRAID and use it as the standard SCS I[...]

  • Page 198

    5-56 Installing the Operating System with Express Setup HostRAID Setup Flow The flowchart below shows the Ho stRAID system setup procedure. St ar t Is HostRA ID used as boot disk ? Ye s Enable the HostRA ID feature and cre ate RAID b y using SCSI Select Utili ty Refer to SCS I Select Utilit y User's Manu al. *1 In sta ll dr iver (install OS ).[...]

  • Page 199

    Chapter 6 Inst alling and Using Utilities This section describes how to use th e NEC EXPRESSBUILDER CD-ROM that comes with your server and to install the utilities stor ed on the NEC EXPRESSBUILDER.[...]

  • Page 200

    6-2 Inst alling and Using Utilities NEC EXPRESSBUILDER NEC EXPRESSBUILDER is an automated software in tegration tool to h elp simplify the process of installing a nd configurin g your serve r. Shipped with all NEC servers, the NEC EXPRESSBUIL DER CD-ROM pr ovides a flexibl e, guided install ation process f or system administrat ors to install Mi cr[...]

  • Page 201

    Installing and Usi ng Utilities 6-3  W indows-based This program is called as "Master Contro l Menu" that can run under the Microsoft W indows system (W indows 95 or l ater and Win dows NT 4.0 or lat er). Y ou can install the several applicatio ns and read the docu mentation from the menu.[...]

  • Page 202

    6-4 Inst alling and Using Utilities NEC EXPRESSBUILDER for DOS- Based with Local Console This subsection describes the p rocedures for u sing NEC EXPR ESSBUILDER for DOS-based w ith local console. St arting NEC EXPRESSBUILDER The following procedure instructs you t o start NEC EXPRESSBUIL DER. IMPORT ANT : Do not remove the NEC E XPRESSBUILDER CD- [...]

  • Page 203

    Installing and Usi ng Utilities 6-5 Express Setup "Express Setup" is intended fo r initial setup of the server. Its automatic installation mode gu ides the user easily through the process by detailing specific h ardware features and providing screen prompts for software selection and configuration . The program loads the utilities and dri[...]

  • Page 204

    6-6 Inst alling and Using Utilities – Save Disk Arr ay Configuratio n Data The configuration information on th e disk mirroring controller is saved into the floppy disk. If you set or change RA ID, always use thi s function to save the confi guration informat ion into a fl oppy disk. IMPORT ANT : Some Disk Array Con trollers do not support this f[...]

  • Page 205

    Installing and Usi ng Utilities 6-7 – W indows Server 2003 x64 Edition O EM-DISK for NEC EX PRESSBUILDER Creates a support disk for installing W indows Server 2003 x64 Editions. – Windows Server 2003 OEM-DISK for N EC EXPRESSBUILDER Creates a support disk for installing W indows Server 2003 Standard Edition and W indows Server 2003 Enterprise E[...]

  • Page 206

    6-8 Inst alling and Using Utilities – Create Maintenance Partition NEC EXPRESSBUILDER creates about 55MB of the maintenance partition on the system disk (or disk array system) as wo rk area. The various utilities are installed when the maintenance partition is created successfully or wh en the maintenance partition is already created. – Install[...]

  • Page 207

    Installing and Usi ng Utilities 6-9 NEC EXPRESSBUILDER for DOS-b ased with Remote Console This subsection describes the procedures fo r using NEC E XPRESSBUILDER for DOS-based w ith remote consol e. NEC EXPRESSBU ILDER contains the remote console feature that allows the system administrator to set up the serv er from the m anagement work station (m[...]

  • Page 208

    6-10 Installin g and Using Utilities Star ti n g The following t wo methods a re available to start t he server .  Running NEC E XPRESSBUIL DER from the m anagement PC via LAN  Running NEC E XPRESSBUILDER from the m anagement PC via direct connectio n (COM B) For the procedure for starting NEC EXPRESSBUIL D ER for DOS-based with Remote Consol[...]

  • Page 209

    Installing and Usi ng Utilities 6-1 1 T op Menu Shown below a re the top menu item s.  Setup Automatically sets up the server .  T ools Launch the features of NEC EXPRESSBUILDER individually .  Help Help message on NEC EXPRESSBUILDER.  Quit Quit NEC EXPRESSBUILDER. Setup The NEC EX PRESSBUI LDER check s the hardw are configu ration of t[...]

  • Page 210

    6-12 Installin g and Using Utilities T ools When you select the [T ools] on the T op Menu, the following screen appea rs. The menu item s available only in remot e console operatio n among those described i n section "NEC EXPRESSBUIL DER for DOS-based wi th Local Console" are displa yed. See the previous subsection for detailed ex planati[...]

  • Page 211

    Installing and Usi ng Utilities 6-13 NEC EXPRESSBUILDER for Window s -Based (Master Control Menu) The Master Control Menu is used to,  Read the User's Guide or the other docum ents,  Update the NEC Express5800 system, and  Install the m anagement soft ware. NOTES:  Master Control Menu requires Microsoft W indows 95 (or later) or W [...]

  • Page 212

    6-14 Installin g and Using Utilities CONFIGURA TION DISKETTE CREA T OR "Configuration Diskette Creator" is a tool to create [Configuration Diskette] that is used fo r configuring the server with the Expr ess Setup (see Chapter 5 for details). If you use the Configuration Diskette create d by the Express Setup and Configuration Diskette Cr[...]

  • Page 213

    Installing and Usi ng Utilities 6-15 4. Click [Configuration Diskette Creator]. Configuration Diskette Creator window is displayed. 5. Click [Create New Information files] from the [File] menu. The [Disk Environment] dialog box will be displayed. 6. Specify each ite m and click on [OK]. The dialog boxes to specify setup information will be displaye[...]

  • Page 214

    6-16 Installin g and Using Utilities 7. Follow the message to specify each item on th e dialog box and click [Next]. NOTE: If you click on [Cancel], all the input value will be deleted. When completing the specification of setup info rmation, the [Save Setup Information] dialog box will appear . 8. Confirm that the [Configuration Diskette] check bo[...]

  • Page 215

    Installing and Usi ng Utilities 6-17 Inst alling Optional Mass Storage Driver T o install op tional Mass Storage Driver that is s u pported by the Express Setu p, follow the procedure below to create [Configuration Diskette]. 1. Display Configuration Diskette Creator window . 2. From the [File] menu, click [Create new information files]. [Disk Envi[...]

  • Page 216

    6-18 Installin g and Using Utilities NEC ESMPRO The NEC ESMPRO (refe rred to as ESMPR O hereafter) lets a system admi nistrator manage remote servers across a net w ork. ESM PRO monitors server ha rdware and softwa re configurations , failures, and performance. W ith log data collect ed by ESMPRO, a system administrator can track long-term and sho [...]

  • Page 217

    Installing and Usi ng Utilities 6-19 Adaptec S torage Manager  - Browser Edition Adaptec St orage Manager  - Browser Edition (hereinafter abbreviated to ASMBE) is a management utility for th e HostRAID system and provides RAID functions through th e SCSI interface in your server . Y ou can use the following functions for HostRAID by installin[...]

  • Page 218

    6-20 Installin g and Using Utilities Adaptec S torage Manager  Adaptec St orage Manager  (hereinaft er abbrevia ted to ASM) is an app lication that locally or remotely ma nages HostRAID stora ge system and p rovides RAID fu nctions through the SCSI interface on the Windows Serve r 2003 x64 Edition in your serv er . Y ou can use the followi ng[...]

  • Page 219

    Installing and Usi ng Utilities 6-21 MegaRAID S torage Manager  (Server) MegaRAID S torage Manager  ( hereinafter abbreviated to MSM) is an application to manage or monitor t he N8103-91 di sk array co ntroller . Y ou can use MSM for managem ent of arrays and error notification by event monitoring while the system is running. Before attemptin[...]

  • Page 220

    6-22 Installin g and Using Utilities Power Console Plus Power Console Plus is a utility to control the RAID system of the disk array con troller (MegaRAID controller ) produced by LSI Logic. Use of Power C onsole Plus e nables operat ions (e.g., m onitoring and maintenance) of RAID system s that are constructed on local NEC Express servers and NEC [...]

  • Page 221

    Installing and Usi ng Utilities 6-23  MegaRAID Re gistration Ser ver Enables control of the Meg aRAID controller via the network. Install in one of NEC Express servers a nd management PCs that are connecte d through networ k. The above components m ust be installed correctly for establishing t he environm ent to use Power Console Pl us. Power Co[...]

  • Page 222

    6-24 Installin g and Using Utilities Server Setup This section expl ains Power Co nsole Plus setu p in the NEC E xpress server in whi ch the MegaRAID controller i s mounted . Operating Environment This section e xplains the o perating envir onment requi red for Powe r Console Pl us to operate on a server .  Hardware – Machine: NEC Express5800 [...]

  • Page 223

    Installing and Usi ng Utilities 6-25 Management PC Setup This section expl ains Power Co nsole Plus setu p in a computer t h at manages ser vers via the net work (TCP/IP). Operating Environment This section e xplains the o perating envir onment requi red for Powe r Console Pl us to operate on a management PC.  Hardware – Machine: NEC Express58[...]

  • Page 224

    6-26 Installin g and Using Utilities NEC DianaScope NEC DianaScope is software fo r the remot e manageme nt of the NEC Exp ress5800 series. See the online documents for details on th e functions and installation of NEC DianaScope. NOTE: Y ou need the server license to activate DianaScope for this product. The server license below is attached to thi[...]

  • Page 225

    Chapter 7 Maintenance This chapter describes the daily mainten ance of the server and precautions wh en relocating or storing the se rver . MAKING BACKUP COPIES NEC recomm ends you make bac kup copies of y our valuable d ata stored in hard disk dri v es of the server on a regul ar basis. F or backup storage devices suitable for the server a nd back[...]

  • Page 226

    7-2 Maintenance CLEANING Clean the server on a re gular basis to keep the se rver in a good shape. W A RNI NG Observe the following instructions to us e the server safely. Failure to follow these instructions may result in death or seri ous personal injury. See pages 1-3 to 1-8 for details.  Do not disassemble, repair, or alter the server.  D[...]

  • Page 227

    Maintenance 7-3 Cleaning the Server For daily cleaning, wipe the external surfaces of the server with a dry soft cloth. Follow the procedure below if stains rem ain on the surfaces: IMPORT ANT :  T o avoid altering the material and color of the server , do not use volatile solvents such as thinn er and benzene to clean the server .  The power[...]

  • Page 228

    7-4 Maintenance Cleaning the Interior One of the most important items in a good maintenance program is regular and thorough cleaning of the interior of the server, esp ecially around the m other board. Dust buildup inside the server can lead to several problems. As dust acts as a thermal insulator , a buildup can prev ent proper system cooling. Exc[...]

  • Page 229

    Maintenance 7-5 Cleaning the Keyboard/Mouse Make sure that the server and peripheral de vices are al l off-powe red (the POWER/SLEE P LED goes of f), and then wipe the ke yboard s urface with a dry cloth. The mouse operation de pends on the degree of smoothne ss of the internal ball rotati on. T o keep the mouse ball clean, use t he mouse in a plac[...]

  • Page 230

    7-6 Maintenance Cleaning CD-ROM A dusty CD-ROM or dust-accumula ted tray causes the device to fail to read data correctly . Follow the procedur e below to clean the tray and CD-ROM regu larly: 1. Make sure that the server is pow ered (the POWER/SLEEP LED is lit). 2. Press the CD tray Open/Close button on the front of the CD-ROM drive. The tray open[...]

  • Page 231

    Maintenance 7-7 SYSTEM DIAGNOSTICS The System Diagnostics runs seve ral tests on the server . Use the System Diagnostics program in the NE C EXPRES SBUILDER provi ded with the server to diagnose the server . T est Items The following items are tested in system diagnostics.  Memory  CPU ca che memor y  Hard dis k drive us ed as a sys tem IM[...]

  • Page 232

    7-8 Maintenance St arting and Ending the System Diagnostics There are two ways to diagnose the server: to u se the local console (keyboar d) of the server itself, and to use the m anagement PC via serial port ( remote consol e). IMPORT ANT : T wo methods o f LAN and the seri al port are mentioned in Chapter 6 "NEC EXPRESSBUILDER" in the w[...]

  • Page 233

    Maintenance 7-9 6. Select [System Diagnostics]. The System Diagnostics starts and com p letes in approximately three minutes. When the diagnosis completes, the screen of the display ch anges in the following indication. [Enter ] Detail I nform ation [ ESC] Ret urn to Enduser Menu Test End T eDoLi(TEst & Diagnosis On Linux) Ve r001.00(Build02090[...]

  • Page 234

    7-10 Maintenance 7. Follow the Guide lin e showed in the botto m of the screen and press ESC to show the End user Menu showe d below . Please choose a function by the arrow key and push Enter key. Enduser Menu T eDoLi ( TEst & Dia gnosis On Linu x) Ver001.00 (Build020901 .1.1m) <T est Result> <Device List> <Log In fo> <Opti[...]

  • Page 235

    Maintenance 7-1 1 RELOCA TING/ ST ORING THE SERVER Follow the procedur e below to relocate or store the server: CAUTION Observe the following instructions to us e the server safely. Failure to follow these instructions may cause a fire, pers ona l injury, or property damage. See pages 1-3 to 1-8 for details.  Never attempt to lift the se rver on[...]

  • Page 236

    7-12 Maintenance (This page is intentionally left b lank.)[...]

  • Page 237

    Chapter 8 T roubleshooting If your server does not operate a s expected, rea d this chapter before assum ing a failure. NOTE: For provision against an unexp ected failure, it is recommended to install the maintenance utility , NEC ESMPRO, to the server and cl ient comput ers.[...]

  • Page 238

    8-2 T roubleshooting SYSTEM VIEWERS Monitor the occurrence of fault by NEC ESMPRO du ring the system operation. Especially take n ote on whether a ny alert is re ported to NEC E SMPRO Manager on the management PC. Check whether any alert is r eported on the Operation W indow , Data V iewer, or Alert V iewer of NEC ESMPRO Manager . [Example] NEC ESM[...]

  • Page 239

    T roubleshooting 8-3 LEDS The server includes LEDs t o indicate the server st ates by a variety of co lors and display p atterns on the front panel, hard di sk drive, and power supply . Chapter 2 "Status Indicators" lists the LED displays and th eir meanings and the actions taken at occurrences of failures.[...]

  • Page 240

    8-4 T roubleshooting ERROR MESSAGES If an error occurs in the server , an error m essage appears on the disp lay unit connected to the serv er . Error Messages af ter Pow er-on Powering on the server automatically starts the self-diagnostic progr am, POST (Power On Self- T est). When the POST detects any error , it di splays an err or message and i[...]

  • Page 241

    T roubleshooting 8-5 POST Error Messages When POST detects an error , it displays an error message on the display unit screen. The following table lists error messages and actions to take. IMPORT ANT : T ake a note on the m essages displayed before consulting with your service repr esen tative. Alarm messages are useful inform ation for maintenance[...]

  • Page 242

    8-6 T roubleshooting Error code Error message Recommended Actio n 02D1 System Memory exceeds the CPU's caching limit. 02F4 EISA CMOS not write able. 02F5 DMA T est Failed. 02F6 Software NMI Failed. 02F7 Fail-safe T imer NMI Failed. Contact your service representative. 0B22 Processors are installed out of order . Request the maintenance to repl[...]

  • Page 243

    T roubleshooting 8-7 Error code Error message Recommended Action 0B8F Could not redirect the console - BMC Parameter Error - 0B90 BMC Platform Information Area c orrupted. 0B91 BMC update firmware corrupted. T urn off the power once and then on again to start the server . If the error cannot be corrected, contact your service representative. 0B92 I[...]

  • Page 244

    8-8 T roubleshooting DIMM #1 DIMM #2 DIMM #3 DIMM #4 DIMM #5 DIMM #6 DIMM #7 DIMM #8 Group #1 Group #2 Group #3 Group #4 Processor 1 Processor 2[...]

  • Page 245

    T roubleshooting 8-9 Beep Codes If an error occurs during the POST , the se rver beeps, indicat ing the type of er ror . Each number indicates the number of short beeps, a nd a hyphen indicates a pause. For exam ple, the beep interval 1-5-2-2 indicates 1 beep, pause, 2 beeps, pause, 2 beeps, p ause, and 3 beeps notifying that no processor is detect[...]

  • Page 246

    8-10 T roubleshooting SOL VING PROBLEMS When the server fails to operate as expected, see the follo wing to find out y our problem and follow the instructio n given before asking for re pair . If the server still fails to operat e successfully after solv i ng your problem, ta ke a note on the on- screen message and contact your se rvice representat[...]

  • Page 247

    T roubleshooting 8-1 1 No screen disp lay appears with b eep: → Check whether DIMMs are connected to the m ating connectors firmly . → Check whether DIMMs of diffe rent specifica tions are installed in the specific bank. See Chapter 9 for the specifications of DIMMs. → DIMMs must be populated in pairs and in the following order: #5 and #6, #3[...]

  • Page 248

    8-12 T roubleshooting Fail to access to internal or external de vices (or such devices fail to operate): T Are cables properly connected? → Make sure that the interface cables and power cord are properly connected. Also make sure that the cables are connected i n the correct order . T Is the power-on order corr ect? → When the server has any ex[...]

  • Page 249

    T roubleshooting 8-13 The keyboard or mouse fails to operate: T Is the cable properly connected? → Y ou must use the pro vided keyboard/m ouse br anch cable (Y cable) for this server . Make sure that the prov ided cable is conn ected to the correct connector on the rear of the server . → The keyboard or mouse doe s not operate if it is connecte[...]

  • Page 250

    8-14 T roubleshooting Fail to access (read or write) to the flop py disk: T Does the fl oppy disk drive contain a floppy disk ? → Insert a floppy disk into the flopp y disk drive until it clicks. T Is the floppy disk write-protected? → Place the write-protect switch on the flo ppy disk to the "W rite-enabled" position. T Is the flop p[...]

  • Page 251

    T roubleshooting 8-15 Fail to access the hard disk d rive: (Refer to the documentation supplied with the disk array controller .) T Is the hard disk drive applicable to the serv er? → Operation of any devi ce that is not authorize d by NEC is not guara nteed. T Is the hard d isk drive properly installed? → Make sure to lock the hard disk drive [...]

  • Page 252

    8-16 T roubleshooting The server is not fo und on the net work: T Is the LAN cable connecte d? → Make sure to connect the LAN cable t o the networ k port on t he rear of the serve r . Also make sure that the LAN cable to use conforms with the network interface standard. T Is BIOS configuration correct? → The internal LAN controller may be disab[...]

  • Page 253

    T roubleshooting 8-17 Problems with Windows Server 2003 x64 Editions There are some cases that an e vent log is registered as follows w hen you inst all Windows Server 2003 x64 Editions. Source: DCOM Category Err or Event ID 10016 Description: The application -specific permission settings do not grant Local Activ ation permission for the COM se rve[...]

  • Page 254

    8-18 T roubleshooting Problems with Windows Server 2003 R2 There are some cases that an e vent log is registered as follow s when you operate Windows Server 2003 R2. Source: IPMIDR V T ype: Error Event ID: 1001 Description: The IPMI device driver attempted to determine if the system supported an IPMI BMC device. The driver attempted to detect the p[...]

  • Page 255

    T roubleshooting 8-19 Problems with Windows Server 2003 and Windows 2000 Cannot inst all the operating system c orrectly . T Did you confirm the notes on installing the op erating system? → See Chapter 6. During Windows 2000 inst allation, the following warn ing is registered in the Sy stem Log of the Event Viewer: Error detected on th e device [...]

  • Page 256

    8-20 T roubleshooting The system does not restart automatically w hen a stop error occurs, though the system is adjusted to automatically restarting. → When the system does not restart automatically , restart it manually . The system restart s automatical ly when a stop error occurs , though the system is NOT adjusted to automatically restarting.[...]

  • Page 257

    T roubleshooting 8-21 Problems with NEC EXPRESSBUILDER When the server is not booted from the NEC EXPRESSBUILDER CD-ROM, chec k the following: T Did you set the NEC EXPRESSB UILDER du ring POST and restart the server? → If you do not set the NEC EXPRESSBUILDER during POST and restart the server , an error message will appear or the OS will boot. [...]

  • Page 258

    8-22 T roubleshooting Problems with Express Setup Express Setup can not be used → Express Setup do not suppor t the installation of Micro soft W indows Server 2003 x64 Editions. If you want to perform re-setup, see Appendix D a nd perform "M anual Setup". Following message appeared w hen you tried to install Express Setup to the hard di[...]

  • Page 259

    T roubleshooting 8-23 The following error lo g is included in the event log while operating the system: Event ID: 16 Source: iANSMini port T ype: Error Category: No ne Description: T eam #0:Th e last adapter has lost link. Network connecti on has been lost. → Though the above error is in cluded in the event log wh en specifying the teaming, the L[...]

  • Page 260

    8-24 T roubleshooting Windows 2000 started with different display resolu tion from the specified value. → If the specified display resolution can not be used, the system will use the nearest value or the default va lue of the driver . Entered the incorrect Product ID/CD key . → Even if you entered the incorrect Prod uct ID/CD key , Express Setu[...]

  • Page 261

    T roubleshooting 8-25 The following messag e appears on the scre en and the setup is suspen ded while the Express Setup is executing: Bad Command or filename Insufficient disk space → Follow the procedure d escribed below and check the BIOS setting s for the SCSI controller . As for the pr ocedure on the SC SI controller w hich is not desc ribed [...]

  • Page 262

    8-26 T roubleshooting Problems with Configuration Diskette Creator The bit map of the Configuration Diskette Cre ator window is not displayed correctly during setting of setup information. (When the T rekking command is used) → If the specified number of colors is fewer than 256 in the display settin g, the bit map is not displayed correctly , bu[...]

  • Page 263

    T roubleshooting 8-27 COLLECTING EVENT LOG This section describes on how to collect the log of v arious events that occurred on th e server . IMPORT ANT : If STOP error , system error , or stall occurred, follow the procedure below afte r restarting the system. NOTE: The different revision processor may be mixed in addition al CPU kit. When W indow[...]

  • Page 264

    8-28 T roubleshooting COLLECTING CONFIGURA TION INFORMA TION This section describes on how to collect the in formation o n hardware co nfiguration and in side specification. In order to collect information, "Diagnostic Program" is used. IMPORT ANT : If STOP error , system error , or stall occurred, follow the procedure below afte r restar[...]

  • Page 265

    T roubleshooting 8-29 COLLECTING DR. W A TSON DI AGNOSTIC INFORMA TION Dr . W atson collects diagnostic information related to application errors. The location to save the information can be s pecified as you like. F or more information, refe r to Chapter 5. MEMOR Y DUMP If an error occurs, the dump file shoul d be saved to acquire necessary info r[...]

  • Page 266

    8-30 T roubleshooting Saving the Dump File Press the DUMP switch to save the dump file whe n an error occ urs. Insert a metal pin (a straightened large paper clip will make a substitu te) into the switch hole to press the DUMP switch. Pressing the DUMP switch saves the dump file in the specified directory . (Mem ory dumping may not be availabl e wh[...]

  • Page 267

    T roubleshooting 8-31 RECOVER Y FOR W i ndows 2000 SYSTEM If any file necessary for running the OS is damaged, use th e following procedures to recover the system. IMPORTANT:  After recovering the system , see "Updating the System" in Chapter 5 and be s ure to update the system. Also on W indows 2000, you need to upd ate all the driver[...]

  • Page 268

    8-32 T roubleshooting 5. When the following message is displayed, press S . Setup could n ot dete rmine the type of one or more mass storage devices installed in your system, or you have chosen to manually specify an adapter. Currently, Setup will load support fo r the following mass storage devices. The following message is displayed. Please inse [...]

  • Page 269

    T roubleshooting 8-33 11. Follow the instruction displayed on the screen, and then press L at the screen which request you to insert system recovery disk. The system will be restarted once. NOTE: Start s the procedure with out system recovery disk. 12. Repeat steps 4 to 1 1. The recovery procedure will be started. During the recovery , the missing [...]

  • Page 270

    8-34 T roubleshooting OFF-LINE MAINTENANCE UTILITY The Off-line Maintenance Utility is an OS-independent maintenance program. When you are unable to start the OS-dependent NEC ESMPRO to troubleshoot a problem, the Off-line Maintenance Utility can b e used. IMPORT ANT :  The Off-line Maintenance Utility is intended for use of your service represe[...]

  • Page 271

    T roubleshooting 8-35 St arting the Off-line Maintenance Utility The Off-line Maintenance Utility may be started in the following ways.  From the CD-ROM Set the NEC EXPRESSBUILDER CD-ROM in the C D-ROM drive and reboot the system. After the menu is displayed on the screen, se lect "T oo ls" - "Off-line Maintenance Utility". T[...]

  • Page 272

    8-36 T roubleshooting Features of Off-line Maintenance Utility The Off-line Maintenance Utility provides the fo llowing features. (A vailable features vary depending on th e way you started the Off-line Maintenance Utility .) IMPORT ANT : See th e on-line help for details of the Off-line Maintenance Utility . For further information, ask your servi[...]

  • Page 273

    T roubleshooting 8-37 RESETTING THE SERVER If the server halts before starting the OS, press and hold Ctrl and Alt and press Delete . This restarts the server . IMPORT ANT : Resetting the server clears the DIMM memory and the data in process. T o reset the server when it is not frozen, make sure that no processing is in progress.[...]

  • Page 274

    8-38 T roubleshooting FORCED SHUTDOWN Use this function when an OS command does not shut down th e server , th e POWER switch does not turn off the server , or resetting do es not work. Press and hold the POWER switch on the server for at least four se conds. T he power is forcibly turned off. T o turn on the po wer back again, wait approximately 1[...]

  • Page 275

    Chapter 9 Upgrading Y our Server This chapter describes internal optional d evices av ailable for the server, procedures for install or removing such o ptional devices, an d notes on using them . IMPORT ANT :  Optional devi ces described i n this chapter may be i nstalled or removed by any user . However , NEC does not assume any liability for d[...]

  • Page 276

    9-2 Upgrading Y our Server SAFETY NOTES Observe the following notes to install o r remove optional devices safely and properly . W A RNI NG Observe the following instructions to use the server safel y. Failure to follow these instructions may result in death or serious personal in jury. See pages 1-3 to 1-8 for details.  Do not disassemble, repa[...]

  • Page 277

    Upgrading Y our Server 9-3 ANTI-ST A TIC MEASURES The server contains electronic co m ponents sensitive to static electricity . A void failures caused by static electricity when installing or removing any optional dev ices.  W ear a wrist strap (an arm belt or anti-static glove). W ear a wrist strap on your wris t. If no wrist strap is availa bl[...]

  • Page 278

    9-4 Upgrading Y our Server PREP ARING FOR INST ALLA TION AND REMOV AL Follow the p rocedure bel ow to prepare fo r installing or removing c omponents. 1. Shut down the OS. 2. Remove the front bezel from the chassis if installed. 3. Press the POWER switch t o power of f the server (the POWER LE D goes of f). 4. Remove all cables a nd power cords fro[...]

  • Page 279

    Upgrading Y our Server 9-5 CONFIRMA TION AFTER INST ALLA TION/ REMOV AL Confirm the following after installing an add itional option and removing a co mponent:  Installing removed c omponents exactly as they we re Install the components a nd cables, which were removed and disc onnected for addition of an option, exact ly as they we re. Assemblin[...]

  • Page 280

    9-6 Upgrading Y our Server DEVICE INST ALLA TION OR REMOV AL PROCEDURE Install or rem ove a component from t he server in the f ollowing proce dure. Hard Disk Drive The server has six de vice bay slots to install ha rd disk drives with th e SCA2 interface (Ultra 320 SCSI) in the disk bay of the front of the serv er . IMPORT ANT :  Do not use any[...]

  • Page 281

    Upgrading Y our Server 9-7 SCSI ID / SAS Port The hard dis k drive bay ma y contain up to si x hard disk drives. The SCSI IDs or SAS port numbers are factory-assigned to ha rd disk drives as shown below . The hard disk drive bays are conn ected to the SCSI connector on the mother board when the server is shipped. T o use the hard disk drives in a d[...]

  • Page 282

    9-8 Upgrading Y our Server Inst allation T ake th e following steps to install a hard disk drive. This procedure app lies to all the hard disk drive bays. NOTE: Any ha rd disk dri ve can be instal led or rem oved in or from the server only by removing t he front bezel. IMPORT ANT : In the disk a rray configurati on, use the ha rd disk drives having[...]

  • Page 283

    Upgrading Y our Server 9-9 6. Align the drive carrier with the bay guide rail. 7. Slide the drive carrier into the bay until it locks with th e SCSI backplane connector . IMPORTANT:  Push the hard disk drive carrier until the hook of the handle hits the frame.  Hold the hard disk drive carrier with both hands securely and carefully . 8. Close[...]

  • Page 284

    9-10 Upgrading Y our Server Removal T ake the following steps to rem ove a hard disk dri v e: NOTE: If removing a failing hard di sk drive, c onfirm the slot in which the DISK LED of the hard disk drive is amber before starting the removal. 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepare. 2. U[...]

  • Page 285

    Upgrading Y our Server 9-1 1 When the hard disk drives are in the disk array confi guration, you can restore the state before an error using the auto-rebu ild feature that stores the data in t he old hard di sk drive into a new one. The auto-rebuild feature is av aila ble for t he RAID1, RAID5 , or RAID10 di sk array confi guration. NOTE: Onboard R[...]

  • Page 286

    9-12 Upgrading Y our Server Power Supply Unit Y our server contains one or two power supplies. The second pow er supply is op tional and pr ovides a redu ndant configurat ion that ensu res continue d operation of the system in the unlikely even t one of the power supplies fails. Inst allation T ake the fo llowing steps to install a power supply uni[...]

  • Page 287

    Upgrading Y our Server 9-13 4. Insert the pow er supply unit. IMPORTANT: Do not touch the terminals of the power supp ly unit. Gold-plated connectors[...]

  • Page 288

    9-14 Upgrading Y our Server 5. Grasp the handle an d firmly push the pow er supply . The power supply unit is lock ed when a distinct "click" is heard. 6. Connect two po wer cords. Use the power co rd provided wi th the standard power suppl y unit and t he one provided with the system. The AC POWER LEDs fl ash whe n the power cords are co[...]

  • Page 289

    Upgrading Y our Server 9-15 Replacing a Failing Power Supply Unit Replace only a failing power supply unit. IMPORTANT: Do not remove a power s upply unit ope rating normally . NOTE: If one power supply unit fails while the server contain s two power supply units in a redun dan t configuration, the failing power supply unit can be re placed with the[...]

  • Page 290

    9-16 Upgrading Y our Server Server (Pull-out from the Rack) The server needs t o be pulled o ut from the rack f or installing/rem oving any com ponents other than the hard di sk drives and power supply units. CA UTION Observe the following inst ructions to use the server safel y. Failure to follow these instructions may res ult in death or serious [...]

  • Page 291

    Upgrading Y our Server 9-17 Drive Cover Open the dri ve cover whe n installing/rem oving a fan assembly , processor , and backup file de vice or reconnecting an internal cable. Removal 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepare. 2. Pull out the server from the rack. 3. Slide the drive cov[...]

  • Page 292

    9-18 Upgrading Y our Server Logic Cover Open the logi c cover when installing/rem oving a DIMM , processor , and PCI add-in card o r reconnecting an internal cable. Removal 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepare. 2. Pull out the server from the rack. 3. Loosen a captive thumbscrew at [...]

  • Page 293

    Upgrading Y our Server 9-19 DIMM Install the additiona l DIMM (Dual Inline Memory Module) to the DIMM socket on the mother board in the ser ver . T he mother board is provided wit h eight DIMM boa rd slots. NOTE: Up to 16GB of m emory (2GB DIMM x 8) can be installed. (The factory-installed DIMMs need to be replaced in this case.) T wo DIMMs of 512M[...]

  • Page 294

    9-20 Upgrading Y our Server Inst allation Order DIMMs must be populated in pairs and i n the followin g order: #7 and #8, #5 and #6, #3 and #4, then #1 and #2. Install DIMMs starting from the one having smallest capacity . IMPORTANT: Install two additional DIMMs for each g roup *1 because the server uses interleaved m emory . If DIMMs of dif ferent[...]

  • Page 295

    Upgrading Y our Server 9-21 Inst allation Install a DIMM in the following procedur e. IMPORTANT: The server supports DIMMs o f only the low-pro file type (30 m m (1.2 inches) i n height). It does not s upport DIMM s exceeding the specified height. 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepar[...]

  • Page 296

    9-22 Upgrading Y our Server Removal Remove the DIMM depe nding on the following p rocedure. NOTES:  T o remove the fail ed DIMM, check t he error message a ppearing in POST or NEC ESMPR O to identify th e DIMM socket (group) in which the failed DIMM is installed.  The server operates on ly when at least two DIMMs are installed. 1. See the sec[...]

  • Page 297

    Upgrading Y our Server 9-23 Processor (CPU) The server ma y have another C PU installed i n addition to t he standard CPU (Intel  Xeon  Processor). IMPORT ANT :  The CPU is extremely sensitive to static electricity . Mak e sure to touch the metal frame of the server to discharge static electricity from your body befo re handling the CPU. D[...]

  • Page 298

    9-24 Upgrading Y our Server Inst allation T ake the fo llowing steps to install the CPU. 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepare. 2. Pull out the server from the rack. 3. Open the dri ve cover and logic cover . 4. Remove two sc rews securing the support arm . 5. Remove the support arm [...]

  • Page 299

    Upgrading Y our Server 9-25 8. Raise the locking lev er on the socket. IMPORT ANT : Open th e lever until it stops. The bar can be opened to approx. 120 degrees . 9. Aligning the pins of t he CPU with the socket , insert the CPU slowly and gently into the socket. IMPORT ANT :  Be aware of CP U direction. Pin layouts o n two corners am ong four d[...]

  • Page 300

    9-26 Upgrading Y our Server 10. Push the CPU lightly to the sock et, an d pus h down the le ver to secure t he CPU. 11. Put the heat si nk on CPU. NOTE: Be aware of direction of h eat sink (see figure below) . 12. Fix the heat sink clips with four screws. 1 2 3 4[...]

  • Page 301

    Upgrading Y our Server 9-27 13. Make sure that the heat sink is lev el. NOTES:  If the heat sink is not level, remove it, and then install it again. The following probably causes the heat sink not to be level: – The CPU is no t positioned correctly . – All screws are not co mpletely tightened.  Do not move t he secured heat sink. 14. Inst[...]

  • Page 302

    9-28 Upgrading Y our Server 16. Install the co vers you rem oved previously . 17. Power on the server , start the SETUP utility , and set "Processor Retest" of "Processo r Settings" on the Main menu to "E nable". 18. V erify that POST displays no error messages. If POST displays an e rror message, take a note on the m [...]

  • Page 303

    Upgrading Y our Server 9-29 Removal T o remove the CPU, p repare the removal referring to ste ps 1 and 6 in t he installation p rocedure and do the reverse procedure o f steps 12 to 8. IMPORTANT:  Do not remove any CPU unless it is failed.  After the operation, heat may make the cool seat at t he bottom of the heat sink adhere to the CPU. T o[...]

  • Page 304

    9-30 Upgrading Y our Server PCI Board The server has two "rise r cards" on the mother board that enable installation of PCI bo ards. Three PCI boards ca n be installed o n each riser car d. (Up to six PCI boa rds can be installed i n total.) Insert PCI boards for network extensi o n and fil e device functi on extension i nto PCI board sl [...]

  • Page 305

    Upgrading Y our Server 9-31 Notes Observe the fol lowing notes on installing/ removing a PCI boa rd:  Do not touch the terminals of the riser card s and the leads of electronic components with your bare ha nd. Fingerpri nts and dust l eft on them cause t he server to m alfunction due to a connection failure or damage to the leads.  A riser ca[...]

  • Page 306

    9-32 Upgrading Y our Server  If a bootable PCI board (e.g., a dis k array controller , SCSI controller , or LAN card) is additionally installed , the boot priority is changed to the default. After the additional installation, start the BIOS SETUP utility , select [Boo t] → [Boot Device Priority], and set the new boot pri ority .  If an opti[...]

  • Page 307

    Upgrading Y our Server 9-33 Inst allation T ake the fo llowing steps to install a PCI board on the riser card: IMPORTANT:  Each riser card s upports low-pr ofile or ful l-height PCI boa rds. Before installing a PCI board, confirm that the type of the PCI board.  When install ing a PCI boar d, confirm that the card connector matches the connec[...]

  • Page 308

    9-34 Upgrading Y our Server 6. Remove the ext ension slot co ver . NOTE: Keep the removed ext ension slot cover for futu re use. 7. <This step is required only for a PCI boa rd of the full-height/fu ll-length type.> Before installing a PCI board of the full-heigh t/full-length type, remove the retainer from the PCI board, and then un lock and[...]

  • Page 309

    Upgrading Y our Server 9-35 8. Install the PCI board on the riser card. Align the PCI board terminal section with th e riser card slot, and firmly push t he PCI board until it is fully seated. IMPORTANT:  Do not touch the terminals of th e riser cards and PCI boar ds with your bare ha nd. Fingerpri nts and dust l eft on them cause t he server to[...]

  • Page 310

    9-36 Upgrading Y our Server 9. Secure the board with a screw removed in Step 5. 10. Insert the riser card into the slot on the moth er board. Align the riser card terminal section with the slot on the mother board, and firmly push the riser card until it is fully seated. Retainer clip Retainer clip Low-profile type Full-height type Lock tab[...]

  • Page 311

    Upgrading Y our Server 9-37 11. After the insertion, press the riser card down with your fingers until it is fully seated. 12. Install the com ponents you removed pre viously . 13. V erify that POST displays no error messages. If POST displays an e rror message, take a note on the m essage and see the POST er ror messages listed in Chapter 8. 14. S[...]

  • Page 312

    9-38 Upgrading Y our Server Disk Array Controller Board The disk array controller board is an optiona l PCI board provided to improve data reliability . Installing the disk array con troller board allows you to use ha rd disk drives in the device bays of the server and th ose in the optio nal expansion disk cabinet in the disk array con figuration.[...]

  • Page 313

    Upgrading Y our Server 9-39 Use of internal hard disk drives in a disk array configuration T o use the internal har d disk drives in a disk array co nfiguration in the se rver containi ng a disk array controller board, reconnect the SCSI ca bl es and LED ca bles on the mother board. The internal hard disk dri ve in terface is connected to the SCSI [...]

  • Page 314

    9-40 Upgrading Y our Server With N8103-86 disk array controller connected With N8103-80F/81F disk array controller connected Mother board Hard disk drive SCSI ID3-5 Internal backup device Hard disk drive SCSI ID0-2 SCSI backplane SCSI connector N8103-86 disk array controller Mother board Hard disk drive SCSI ID3-5 Internal backup device Hard disk d[...]

  • Page 315

    Upgrading Y our Server 9-41 With N8103-86 disk array controller connected and internal SCSI backup device connected (exclusive use with onboard SCSI connector) With N8103-80F/81F disk array controller connected and internal SCSI backup device connected (exclusive use with onboard SCSI connector) Hard disk drive SCSI ID3-5 Internal SCSI backup devic[...]

  • Page 316

    9-42 Upgrading Y our Server With N8103-86 disk array controller connected and internal IDE backup device With N8103-91 disk array controller connected Hard disk drive SCSI ID3-5 Internal SCSI backup device Hard disk drive SCSI ID0-2 SCSI backplane N8103-86 disk array controller Mother board SCSI connector REAR FRONT Connect the SCSI cable to the SC[...]

  • Page 317

    Upgrading Y our Server 9-43 With N8103-91 disk array controller connected and internal IDE backup device With N8103-91 disk array controller connected and internal SCSI backup device SAS hard disk drive Ports 3-5 Internal IDE backup device SAS hard disk drive Ports 0-2 N8154-10 SAS back panel N8103-91 disk array controller (for internal HDD) Mother[...]

  • Page 318

    9-44 Upgrading Y our Server  SCSI cable connection T o use the internal har d disk drives in a disk array confi guration, disconnect the SCSI cable from the SCSI connector on the mother board, and conn ect it to the connector of the disk array cont roller board . IMPORTANT:  T o switch th e internal hard disk drives into a disk array configur[...]

  • Page 319

    Upgrading Y our Server 9-45  LED relay cable connection T o indicate the status of access to the inte rnal hard disk drives i n a disk array configuration, connect the LED relay cable connected on the moth er board connector to the HDD LED connect or on the mother board and to t he HDD LED con nector of the disk array controller . NOTES:  Whe[...]

  • Page 320

    9-46 Upgrading Y our Server Pin (Red) Pin (Red) N 8103-80F N 8103-81F[...]

  • Page 321

    Upgrading Y our Server 9-47  Disk array confi g uration of i nternal hard disk drives Observe the follow ing notes on configur ing a disk array: – The server must contain more tha n one SCSI or SAS ha rd disk drive havin g the same capacity and the same rotational speed. (The m inimum number of requi red disks depends on the confi guration of [...]

  • Page 322

    9-48 Upgrading Y our Server Use of a disk exp ansion unit in a disk array configuration A disk expansio n unit is an excl usive device that ca n install up to 14 hard disk d rives. (The num ber of hard dis k drives depen ds on the m odel.) The server cont aining a dis k array control ler board can connect one or two of these de vices. For details o[...]

  • Page 323

    Upgrading Y our Server 9-49 Backup Device The server has one slot for installin g a backup device such as a magnetic tape drive. IMPORTANT:  A SCSI cable K410-130(00) is necessary for installing a SCSI backup device.  Set "OFF" for the terminating resist or of the backup device y ou are going to i nstall, and set a SC SI ID dif fere[...]

  • Page 324

    9-50 Upgrading Y our Server Inst allation 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepare. 2. Pull out the server from the rack. 3. Open the dri ve cover and logic cover . 4. While pulling the lever toward the right side of the serv er , pull th e CD/FD out of the chassis. IMPORT ANT : Do not [...]

  • Page 325

    Upgrading Y our Server 9-51 6. T ake out the device carrier from the front of the server . 7. Push the tabs at both ends of the front pan el. 8. Remove the f ront panel. IMPORTANT: Keep the remove d front panel for future use. 9. Insert the backup device int o the device carrier .[...]

  • Page 326

    9-52 Upgrading Y our Server 10. Secure the backup dev ice with the provided screws. T ighten two screws on each side. NOTES:  Be sure to use the screws provided with the b ackup device.  Position the backup d evice so that the device screw holes align with the screw holes in the de vice carrier .  If you feel dif f icult to connect the cab[...]

  • Page 327

    Upgrading Y our Server 9-53 12. Insert the device carrier i nto the backup device bay half way . Push the device carrier as far as it will go. It is locked when a "click " is heard. NOTE: Be careful not to catch the co nnect ed power e xtension cable in inserting the device carrier . 13. Connect the interface ca ble and powe r cable to th[...]

  • Page 328

    9-54 Upgrading Y our Server 15. Route the SCSI cable as shown in figure below . (SCSI device only) 16. Install the com ponents you removed pre viously . 17. Make the setup acc ording to "SCS I BIOS" in Cha pter 4 (SCSI devi ce only). 18. Install the device driver . Refer to the manual that comes with the device. Removal Remove the bac kup[...]

  • Page 329

    Upgrading Y our Server 9-55 Redundant Hot Swap-fan Y our server can include four optional redu ndant hot-swap fans. Inst allation 1. See the section "Pre paring for I nstallation an d Removal" desc ribed earlier t o prepare. 2. Pull out the server from the rack. 3. Open the dri ve cover . 4. Locate the installation slot. 5. Insert the hot[...]

  • Page 330

    9-56 Upgrading Y our Server 6. Change the jumper (J1 1) setting as shown in figure below . J11 IMPORT ANT : T o avoid system malfunction, leave other jum pers at its default position. If the remote management card is installed in your server , follow these steps to configure the firmware pro gram. 7. Place the NEC EXPRESSBUILDER C D-ROM in to the C[...]

  • Page 331

    Upgrading Y our Server 9-57 Removal Follow these steps to remove or re place the hot-swap fan. 1. Pull out the server from the rack. 2. Open the dri ve cover . 3. Locate the failed fan. Fault LED on the fa n turns on when a fan failure occurs. A fan failure is also indicated by NEC ESMPRO and system event log. 4. While pressing release tabs on the [...]

  • Page 332

    9-58 Upgrading Y our Server Remote Management Card (RMC) Remote Managem ent Card (RMC) is an e xpansion card t hat includes the Base board Management Controlle r (BMC) based on IPM I 1.5. See Chapter 2 for detail functions of RMC. IMPORT ANT : The RMC is extremely sensitive to static electricity . Make sure to touch the metal frame of the server to[...]

  • Page 333

    Upgrading Y our Server 9-59 Inst allation Follow these steps to replace the RMC with an optional Advanced Remote Management card (ARMC). 1. See section "Prepa ring for Instal lation and Rem oval" described earl ier to prepare . 2. Pull out the server from the rack. 3. Open the logi c cover . 4. Assemble the m anagement network car d that [...]

  • Page 334

    9-60 Upgrading Y our Server 9. Run "Initialize Remote Management Card". See Chapter 6 for details. 10. Run BIOS SETUP utility and check to see that the menus related to the RMC are displayed. Refer to Chapter 4 for details. If no add itional menus are displayed, reinstall the RMC. 11. In the BIOS SETUP utility , select "Y es" fo[...]

  • Page 335

    Upgrading Y our Server 9-61 Removal 1. See section "Prepa ring for Instal lation and Rem oval" described earl ier to prepare . IMPORT ANT : The remote m anagement card logic m onitors and l ogs system volt age changes. When removing the RM C from the m other board, you may experience a 3 - 4 second del ay from the t ime your system powe r[...]

  • Page 336

    9-62 Upgrading Y our Server (This page is intentionally left b lank.)[...]

  • Page 337

    Appendix A S pecifications NEC Express5800/120Rh -2 Item N8100- 1061F N8100- 1062F N8100- 1063F N8100- 1 100F N8100- 1 125F N8100- 1 126F T ype Intel  Xeon  processor Clock/Cache 3.20DGHz /1MB 3.40DGHz /1MB 3.60GHz /2MB 3.20GHz /2MB 3.40GHz /2MB 3.80GHz /2MB S tandard 1 CPU Maximum 2 Chipset E7520 (800MHz) Minimum 1GB (512MB × 2) Maximum 16G[...]

  • Page 338

    A-2 S pecifications (This page is intentionally left blank .)[...]

  • Page 339

    Appendix B Other Precautions T ransfer Rate of the On-board LAN Controller The mother board includes the t wo network interface controllers that supports 10Base-T , 100Base- TX, and 1000B ase-T networks and a ca pable of full or half duplex. The both controllers can aut oma tically detect and swit ch for networ k speed and t ransfer mode connected [...]

  • Page 340

    B-2 Other Precaution s Notes on use The floppy disk is an im portant data st orage medi a with delicate structure and requires care. Kee p the following notes in mind to use it:  Insert the floppy dis k into the floppy disk drive gently as far as it goes.  Attach the label to the correct position .  Do not writ e anything directly onto t h[...]

  • Page 341

    Other Precaution s B-3  W rite-pro tection A floppy disk has a write-protect switch that prevents the stored data from accidental erasure. Y ou can read data fr om a write-protect ed floppy disk, but you cannot save dat a into the floppy disk or format it. NEC recom mends that you s hould write-prot ect any floppy disk containing val uable data [...]

  • Page 342

    B-4 Other Precaution s CD-ROM Keep the following notes in mind to use the CD-ROM for the server:  Press the center of the storage case to remove the C D-ROM from the case.  Do not drop the CD-RO M.  Do not place anything on the C D-ROM or bend the CD-ROM.  Do not attach any label onto the CD-ROM.  Do not touch the signal side (no thi[...]

  • Page 343

    Other Precaution s B-5 This enables you, for example, to use tape B to restore the data when tape C makes a read error . Also when both tape s B and C make a read err or , you can restore your valuable data by using the data stored in tape A. Keyboard The keyboard is a device t o instruct you computer by entering al phanumeri c characters or sym bo[...]

  • Page 344

    B-6 Other Precaution s Mouse Like the keyboa rd, the m ouse is a device to i nstruct your com puter . Many OS's and appli cation software re quire the mouse f or operation. NOTE:  Functions assig ned to the m ouse buttons vary depe nding on the software. For details, refer to the manual prov ided with the software.  Use the mouse on a cl[...]

  • Page 345

    Appendix C IRQ The factory-set interrupt requests is listed below . Find an appropriate one to i nstall an optional device. IRQ Peripheral Device (Controller) IRQ Periphera l Device (Controller) 0 System timer 12 Mouse 1 Keyboard 13 Numeric processor 2 – 14 Primary IDE 3 COM2 serial port (PCI) 15 Secondary IDE 4 COM1 serial port (PCI) 16 USB 5P C[...]

  • Page 346

    C-2 IRQ (This page is intentionally left b lank.)[...]

  • Page 347

    Appendix D Inst alling Windows Server 2003 x64 Editions This section explains how t o insta ll the W indows Server 2003 x64 Editions. BEFORE INST ALLING WINDOWS SERVER 2003 X64 EDITIONS Please read carefully th e following information BEFORE co mmencing your W indows Server 2003 x64 Editions Installatio n. Optional Board Supported by NEC EXPRESSBUI[...]

  • Page 348

    D-2 Installing Windows Server 2003 x64 Editions Up dating System If you modified t he W indows system, execute "U pdat e Express5800 system" in Master C ontrol Menu. Re-inst alling to the Hard Disk Drive w hich has been upgraded to Dynamic Disk If you want to leave the existing partition when installin g the system on the hard disk drive [...]

  • Page 349

    Installing Windows Server 2003 x64 Editions D-3 Partition Size The size for the partition that the system is to be installed can be calculated from the following formula. Size necessary to install the system + Paging File Size + Dum p File Size + Application Size Size necessary to install the system = 4100MB Paging File Size (R ecommended) = Mounte[...]

  • Page 350

    D-4 Installing Windo ws Server 2003 x64 Editions INST ALLING WINDOWS SERVER 2003 X64 EDITIONS Preparations for Installation  NEC EXPRESSBUILDER CD-ROM  Microsoft W indows Server 20 03 R2 Standard x64 Edition / Microsoft W indow s Server 2003 R2 Enterprise x64 Edition / Micro soft W indows Server 2003 Standard x64 Edition / Microsoft W indows [...]

  • Page 351

    Installing Windows Server 2003 x64 Editions D-5 6. Select [W indows Server 2003 x64 Ed ition OEM-DISK for NEC EXPRESSBUILDER] from [Create Suppo rt Disk] menu. 7. Insert a flo ppy disk int o the floppy dis k drive accordi ng to the instr uction on the sc reen. W indows Server 2003 x64 Edition OEM-DI SK for NEC EXPRESSBUILDER will be created. W rite[...]

  • Page 352

    D-6 Installing Windo ws Server 2003 x64 Editions Windows Server 2003 x64 Editions Clean Installation This section explains how to perform a clean installation of W indows Serv er 2003 x64 Editions. 1. T urn on the system power . 2. Insert the W indows Server 2003 x64 Edition CD-ROM into the CD-ROM drive. 3. Press Ctrl + Alt + Delete to reset the sy[...]

  • Page 353

    Installing Windows Server 2003 x64 Editions D-7 7. Select the proper SCSI Adapter and press Enter . – Adaptec HOSTRAID driver for W indows XP/2003 x64 Edition (When Adap tec HOSTRAID (SCSI) is installed.) – MegaRAID SC SI 320-1 R AID Control ler Drive r (When N8103-80 F board is installed.) – MegaRAID SC SI 320-2 R AID Control ler Drive r (Wh[...]

  • Page 354

    D-8 Installing Windo ws Server 2003 x64 Editions Reinst allation to Multiple Logical drives This subsection describes the pro cedure for reinst alling th e operation system if the multiple logical drives exist. Before Re-inst alling the Operation System Be sure to make backup copies before re-installing the operation system just in case. Re-inst al[...]

  • Page 355

    Installing Windows Server 2003 x64 Editions D-9 Procedure for Modifying the Drive Letter Be careful that the drive letter of the system or boot vo lume cannot modify with the following procedure. 1. Click Start menu, right-click [My Comput er], and specify [Manage] to start [Computer M anagement ]. 2. Specify the [Dis k Managem ent] in the left si [...]

  • Page 356

    D-10 Installing Windows Se rver 2003 x64 Editions Up dating the System T o ensure normal sy stem operation y ou should updat e your system using the followin g procedures. 1. Logon to the system using the administrator acc ount or other account which is a m ember of the Administrators group . 2. Insert the NEC EXPRESSB UILDER CD-ROM into the CD-ROM[...]

  • Page 357

    Installing Windows Server 2003 x64 Editions D-1 1 DRIVER INST ALLA TION AND ADV ANCED SETTI NGS This section desc ribes on how t o install and set up various stan dard drivers m ounted on the device. For the information on installing and setting up the driver that is not described in this section, please refer to the docum ent a ttached to the driv[...]

  • Page 358

    D-12 Installing Windows Se rver 2003 x64 Editions Network Driver Specify the details of network driver . One standard network driver th at is mounted will be installed automatically , but the link speed and Duplex mode nee d to be speci fied manually . [When PROSet is not installed] 1. The [Local Area Connection Prop erties] dialog box appears. * T[...]

  • Page 359

    Installing Windows Server 2003 x64 Editions D-13 Optional Network Board Driver If you want to utilize optional Network Bo ard (N8104 -86/88/1 11), install the driver stored in NEC EXPRESSBUILDER CD-ROM. In case of utilizing (N8104-86/88/11 1 ) "CD-ROM Drive Letter:WINNTW 2K3AMDNS1 PRO100WS03_32E" In case of utilizing (N8104-1 12/103/[...]

  • Page 360

    D-14 Installing Windows Se rver 2003 x64 Editions Adapter Fault T olerance (AFT)/Adaptive Load Balancing (ALB) Adapter Fault T olerance (AFT) is a feature th at cr eates a group containing more than one adapter and automatically converts t he pr ocess of the working adapter to the other ada pter in the group when any trouble occurred on that ada pt[...]

  • Page 361

    Installing Windows Server 2003 x64 Editions D-15 Graphics Accelerator Driver Standa rd graphics accelerator drivers t hat are mounted will be installed a utomatically . The following is the procedure when it is necessary to install manually . If you want to utilize optional Graphics Accelerator Driver board, follow th e doc ument attached to the bo[...]

  • Page 362

    D-16 Installing Windows Se rver 2003 x64 Editions Inst alling RAID Controller Driver (N8103-80F/81F) T o additionally install the N81 03-80F/81F in a system containi ng W indows Server 2003, conne ct the controller and take the following steps to install the driv er: 1. Start [Device Ma nager] from [S tart] menu → [Cont rol Panel] → [Adm inistr[...]

  • Page 363

    Appendix E Inst alling Windows Server 2003 This section e xplains how t o install the Win dows Server 2003 without using Expre ss Setup. BEFORE INST ALLING WINDOWS SERVER 2003 Please read carefully th e following information BEFORE co mmencing your W indows Server 2003 Installation. Optional Board Supported by NEC EXPRESSBUILDER NEC EXPRESSBU ILDER[...]

  • Page 364

    E-2 Installing Windo ws Server 2003 Disk Array Controller (N8103-91) Disk Array Contro ller (N8103-9 1) supports W indows Server 2003 Service Pack 1 or later . If your system is not Service Pac k 1 or later , please update Service Pack. Inst alling Service Pack Y ou can install the Service Pack on the server. When the Service Pack is not attached t[...]

  • Page 365

    Installing Windows Server 2003 E-3 Partition Size The size for the partition that the system is to be installed can be calculated from the following formula. Size necessary to install the system + Paging File Size + Dum p File Size + Application Size Size necessary to install the system = 2900MB (Only W indows Serv er 2003) 3500MB (Wi ndows Server [...]

  • Page 366

    E-4 Installing Windo ws Server 2003 About the Upgrade to Windows Server 2003 R2 The "in-place upgrade" from W indows Server 20 03 t o W indows Server 2003 R2 is not recommended beca use it may over write any files or registries, and cause unexpected im pact to the system or the application s. If you install W indow s Server 2003 R2, backu[...]

  • Page 367

    Installing Windows Server 2003 E-5 INST ALLING WINDOWS SERVER 2003 Preparations for Installation  NEC EXPRESSBUILDER CD-ROM  Microsoft W indows Server 2003 R2 Standard Edition / Microsoft W indows Server 2003 R2 Enterprise Edition / Micro soft W indows Se rver 2003 Standard Edition / Microsoft W indows Server 2003 Enterprise Ed ition (CD-ROM)[...]

  • Page 368

    E-6 Installing Windo ws Server 2003 6. Select [W indows Server 2003 OEM-DISK for NEC EXPRESSBUILD ER] from [Create Support Di sk] menu. 7. Insert a flo ppy disk int o the floppy dis k drive accordi ng to the instr uction on the sc reen. W indows Server 2003 OEM-DISK for NE C EXPRESSBUILDER will be created. W rite-pro tect and attach a label, then k[...]

  • Page 369

    Installing Windows Server 2003 E-7 Windows Server 2003 Clean Inst allation This section expl ains how t o perform a clean i nstallation of W indows Serve r 2003. 1. T urn on the system power . 2. Insert the Windo ws Server 200 3 CD-ROM int o the CD-ROM drive. 3. Press Ctrl + Alt + Delete to reset the system. After a bootabl e operating syst em has [...]

  • Page 370

    E-8 Installing Windo ws Server 2003 7. Select the proper SCSI Adapter and press Enter . – Adaptec HostRA ID U320 Driver V er 1.02 For W indows 20 00/XP/2003 (When Adaptec HostRAID (SCSI) is installed.) – MegaRAID SC SI 320-1 R AID Control ler Drive r (When N8 103-80F boa rd is install ed.) – MegaRAID SC SI 320-2 R AID Control ler Drive r (Whe[...]

  • Page 371

    Installing Windows Server 2003 E-9 Upgrade Inst allation IMPORT ANT : It is not the proced ure of upgrade installation to W indows Server 2003 R2 from W indows Ser ver 2003. Please refer to [About the upgra de to W indows Server 2003 R2] for details. NOTE: Please do the upgra de installation aft er deleting t he graphics accelerator driver . Proced[...]

  • Page 372

    E-10 Installing Wi ndows Server 2003 7. When the following message is displayed, press S . Setup could n ot dete rmine the type of one or more mass storage devices installed in your system, or you have chosen to manually specify an adapter. Currently, Setup will load support fo r the following mass storage devices. The following message is displaye[...]

  • Page 373

    Installing Windows Server 2003 E-1 1 12. When W indows Server 2003 R2 has been in stalled, th e [W indows setup] screen will b e displayed after logged on to the system. IMPORT ANT :  In this case, t he [W indows setup] scree n may not be displaye d. Be sure to install Microsof t W ind ows Server 2003 R2 DISC 2 according to the following procedu[...]

  • Page 374

    E-12 Installing Wi ndows Server 2003 Reinst allation to Multiple Logical drives This subsection describes the pro cedure for reinst alling th e operation system if the multiple logical drives exist. Before Re-inst alling the Operation System Be sure to make backup copies before re-installing the operation system just in case. Re-inst alling the Ope[...]

  • Page 375

    Installing Windows Server 2003 E-13 Procedure for Modifying the Drive Letter Be careful that the drive letter of the system or boot vo lume cannot modify with the following procedure. 1. Click Start menu, right-click [My Comput er], and specify [Manage] to start [Computer M anagement ]. 2. Specify the [Dis k Managem ent] in the left si de of the wi[...]

  • Page 376

    E-14 Installing Wi ndows Server 2003 Up dating the System - Installing Service Pack - IMPORT ANT : If you install W indows Server 2003 CD-ROM which contains Service Pack 1 to your sy stem, you do not have to appl y Service Pack 1 again. T o ensure normal sy stem operation y ou should updat e your system using the followin g procedures. 1. Logon to [...]

  • Page 377

    Installing Windows Server 2003 E-15 DRIVER INST ALLA TION AND ADV ANCED SETTI NGS This section desc ribes on how t o install and set up various stan dard drivers m ounted on the device. For the information on installing and setting up the driver that is not described in this section, please refer to the docum ent a ttached to the driver . PROSet PR[...]

  • Page 378

    E-16 Installing Wi ndows Server 2003 Network Driver Specify the details of network driver . One standard network driver th at is mounted will be installed automatically , but the link speed and Duplex mode nee d to be speci fied manually . [When PROSet is not installed] 1. The [Local Area Connection Prop erties] dialog box appears. * The procedure [...]

  • Page 379

    Installing Windows Server 2003 E-17 NOTE: W e recommend you to add [Network Monit or] at [Adding Services]. [Network Mon itor] can m onitor the fram e (or the packet) that the computer installing [Network M on itor] sends or receives. This tool is valuable when analyzi ng network tr ouble. For i nformation on how to install the tool, see the "[...]

  • Page 380

    E-18 Installing Wi ndows Server 2003 Inst alling SCSI Controller Driver (N8103-65F) If you utilize SCSI controller driv er (N8103-65F), insta ll it according to the following proce dure: 1. Start [Device Ma nager] from [S tart] menu → [Cont rol Panel] → [Admi nistrative T ools] → [Computer M anagement ]. 2. Double-clic k the SCSI Cont roller [...]

  • Page 381

    Installing Windows Server 2003 E-19 Inst alling SCSI Controller Driver (N8103-75) If you utilize SCSI controller driv er (N8103-75), insta ll it according to the foll owing procedure: <In the case of use of Wi ndows Server 2003 SevicePack1 or W indows Server 2003 R2> If you utilize SCSI controller driver (N810 3-75), update your system with N[...]

  • Page 382

    E-20 Installing Wi ndows Server 2003 Inst alling Disk Array Contro ller Driver (N8103-80F/81F) T o add itionally install the N81 03-80F/81F in a system containing W indo ws Server 2003, connect the controller and take the following steps to install the driv er: <In the case of use of Wi ndows Server 2003 SevicePack1 or W indows Server 2003 R2>[...]

  • Page 383

    Installing Windows Server 2003 E-21 About Windows Activation W indows Server 2003 must be activated before you can u se W indows Server 2003. W indows activation process is as follows. NOTE: When you use Wi ndows Server 2 003 R2, activation process is not needed. 1. Click [Run] on [S tart] menu. T ype as follows in t he [Open:] b ox, and click [ OK[...]

  • Page 384

    E-22 Installing Wi ndows Server 2003 The following screen is displayed. 3. Process "W indows activation" according to the following message.[...]

  • Page 385

    Installing Windows Server 2003 E-23 A vailable Switch Options for Windows Server 2003 Boot.ini File Many different switches will be ava ilable if you edit Boo t.ini file. For the available switch options, refer to the following information:  Microsoft Knowledge Base - Article ID: 833721 "A vailable switch options for the W indows XP and the[...]

  • Page 386

    E-24 Installing Wi ndows Server 2003 SETTING FOR COLLECTING MEMOR Y DUMP (DEBUG INFORMA TION) Set for collect ing memory d ump using the procedure described i n Chapter 5.[...]

  • Page 387

    Appendix F Inst alling Windows 2000 This section explains how to install th e W indows 2000 without using Express Setup tool. BEFORE INST ALLING WINDOWS 2000 Please read carefully th e following information BEFORE co mmencing your W indows 2000 Installation. Optional Board Supported by NEC EXPRESSBUILDER NEC EXPRESSBU ILDER CD-ROM attached to your [...]

  • Page 388

    F-2 Installing Windows 2000 Disk Array Controller (N8103-91) Disk Array Contro ller (N8103-9 1) does not support W indows 2000. Inst alling Service Pack Y ou can install the Service Pack on the server. When the Service Pack is not attached to your system, prepare it by yourself. Up dating System If you modified t he W indows system, execute "U[...]

  • Page 389

    Installing Wind ows 2000 F-3 Partition Size The size for the partition that the system is to be installed can be calculated from the following formula. Size necessary to install the system + Paging File Size + Dum p File Size + Application Size Size necessary to install the system = 1000MB Paging File Size (R ecommended) = Mounted Mem ory Size * 1.[...]

  • Page 390

    F-4 Installing Windows 2000 INST ALLING WINDOWS 2000 Preparations for Installation  NEC EXPRESSBUILDER CD-ROM  Microsoft W indow s 2000 Server / Micr osoft W indows 2 000 Advanced Ser ver (CD-ROM)  W indow s 2000 Service Pack (CD-ROM)  User's Guide  Getting Started  W indow s 2000 OEM-DISK for NEC EXPRESSBUILDER Creating &quo[...]

  • Page 391

    Installing Wind ows 2000 F-5 7. Insert a flo ppy disk int o the floppy dis k drive acc ording to the instruction on the screen. W indows 2000 OEM-DISK for NEC EXPRESSBUILDER will be created. W rite-pro tect and attach a label, then keep it safely .  Create from [Master Control Menu] [Master Control Menu] runs on the following operating systems. [...]

  • Page 392

    F-6 Installing Windows 2000 Windows 2000 Clean Inst allation This section expl ains how t o perform a clean i nstallation of W indows 2000. 1. T urn on the system power . 2. Insert the W indows 2000 CD-RO M in the CD-ROM drive. 3. Press Ctrl + Alt + Delete to reset the system. After a bootabl e operating syst em has been inst alled on the ha rd dis[...]

  • Page 393

    Installing Wind ows 2000 F-7 7. Select the proper SCSI Adapter and press Enter . – Adaptec HostRA ID U320 Driver V er 1.02 For W indows 20 00/XP/2003 (When Adaptec HostRAID (SCSI) is installed.) – MegaRAID SC SI 320-1 C ontroller Driver (When N8103-80 F board is installed.) – MegaRAID SC SI 320-2 C ontroller Driver (When N8103-81 F board is i[...]

  • Page 394

    F-8 Installing Windows 2000 Procedure for Modifying the Drive Letter Be careful that the drive letter of the system or boot vo lume cannot modify with the following procedure. 1. Click Start menu, right-click [My Computer], and specify [Manage] to start [Computer Management ]. 2. Specify the [Dis k Managem ent] in the left si de of the wind ow . 3.[...]

  • Page 395

    Installing Wind ows 2000 F-9 Up dating the System - Installing Service Pack - IMPORT ANT : This system does not sup port W indows 2000 Serv ice Pack 1 - 3. If you install W indow s 2000 CD-ROM which contains Service Pack 4 to your system, you do not have to ap ply Service Pack 4 again. NOTE: If you run the Update of Syst em with the M O device conn[...]

  • Page 396

    F-10 Installing Windows 2000 DRIVER INST ALLA TION AND ADV ANCED SETTINGS This section desc ribes on how t o install and set up various stan dard drivers m ounted on the device. For the information on installing and setting up the driver that is not described in this section, please refer to the docum ent a ttached to the driver . PROSet PROSet is [...]

  • Page 397

    Installing Wind ows 2000 F-1 1 Network Driver [When PROSet is not installed] 1. Click S tart menu and click [ Network and Di al-Up Connect ion]. The [Network and Dial-Up Conn ection] dialog box appears . 2. Right-click [Local Area Connection] and cli ck [Propertie s] from pop-up m enu. The [Local Area Connection Prop erties] dialog box appears. 3. [...]

  • Page 398

    F-12 Installing Windows 2000 Re-inst all the Netw ork Driver After installing OS and deletin g th e network driv ers, if you want to re-install the netwo rk drivers, follow the procedure below . 1. Restart OS and logon to your system. 2. [Upgrade Device Driver W i zard] dialog box appears. Click [Next]. 3. Confirm that t he [Search for a s uitable [...]

  • Page 399

    Installing Wind ows 2000 F-13 Graphics Accelerator Driver Standa rd graphics accelerator drivers t hat are mounted will be installed a utomatically . The following is the procedure when it is necessary to install manually . If you want to utilize optional Graphics Accelerator Driver board, follow th e doc ument attached to the board to install the [...]

  • Page 400

    F-14 Installing Windows 2000 Inst alling SCSI Controller Driver (N8103-65F/75) If you utilize SCSI controller driv er (N8103-65F/7 5), inst all it according to the following procedure: 1. Start [Device Ma nager] from [S tart] menu → [Cont rol Panel] → [Admi nistrative T ools] → [Computer M anagement ]. 2. Double clic k the SCSI Cont roller dr[...]

  • Page 401

    Installing Wind ows 2000 F-15 Inst alling RAID Controller Driver (N8103-80F/81F) T o add itionally install the N81 03-80F/81F in a system containing W indo ws 2000, connect the controller and take the following steps to install the driver: 1. When the [F ound New Ha rdware W izard] dialog box a ppears, click [Ne xt]. 2. When the [Install Har dware [...]

  • Page 402

    F-16 Installing Windows 2000 Below is the example on how to add /P AE switch to Boot.ini file. 1. Click [Start], poi nt to [Pr ograms], point to [Accessories], a nd then click [Notepad]. 2. On the [File ] menu, clic k [Open...] . 3. In the [Ope n] dialog box , in the [Look i n ] drop-dow n list box, click "%system root%" drive. 4. In the [...]

  • Page 403

    Appendix G Product Configuration Record T able Use this table for inform ation about setup a nd system environment chan ge. Hardware Main Unit Model name Serial No. Date Installed CPU #1 Clock Serial No. Date Installed #2 Clock Serial No. Date Installed Memory #1, #2 Size Serial No. Date Installed #3, #4 Size Serial No. Date Installed #5, #6 Size S[...]

  • Page 404

    G-2 Product Configuration Record T able Backup Device Slot 1 Size Capacity Serial No. Model name T ype number Date Installed PCI Slot #1B Model name Serial No. Date Installed PCI Slot #2B Model name Serial No. Date Installed PCI Slot #3B Model name Serial No. Date Installed PCI Slot #1C Model name Serial No. Date Installed PCI Slot #2C Model name S[...]

  • Page 405

    Product Configuration Record T able G-3 Sof tw are Firmware version OS Name: V ersion: Application of RUR media  Apply Name: V ersion: File system  FA T  HPFS  NTFS  Others ( ) Bundled software installed Licensed software installed Application running when a failure occurred[...]

  • Page 406

    G-4 Product Configuration Record T able (This page is intentionally left b lank.)[...]