English dropdown-ico

Miller Electric XMT 400 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Miller Electric XMT 400, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Miller Electric XMT 400 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Miller Electric XMT 400. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Miller Electric XMT 400 should contain:
- informations concerning technical data of Miller Electric XMT 400
- name of the manufacturer and a year of construction of the Miller Electric XMT 400 item
- rules of operation, control and maintenance of the Miller Electric XMT 400 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Miller Electric XMT 400 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Miller Electric XMT 400, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Miller Electric service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Miller Electric XMT 400.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Miller Electric XMT 400 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Processes Multiprocess W elding OM-217 769L 2007 − 11 Description Arc W elding Power Source XMT 400 (400 V olt Model) R V isit our website at www.MillerWelds.com File: MUL TIPROCESS[...]

  • Page 2

    Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .Mille[...]

  • Page 3

    T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2. Arc W elding Hazards 1 . . . . . . . [...]

  • Page 4

    [...]

  • Page 5

    OM-217 769 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _2007 − 04 7 Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury . The possible hazards are shown in the adjoining symbols[...]

  • Page 6

    OM-217 769 Page 2 W elding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. FUMES AND GASES can be hazardous. D Keep your head out of the fumes. Do not breathe the fumes. D If inside, ventilate the area and/or use local forced ventilation at the arc to remove welding fumes and gases. D If ventilation is poo[...]

  • Page 7

    OM-217 769 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.[...]

  • Page 8

    OM-217 769 Page 4 1-4. California Proposition 65 W arnings W elding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer . (California Health & Safety Code Section 25249.5 et seq.) Battery posts, terminals and related accessories contain lead and [...]

  • Page 9

    OM-217 769 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION fre_som_2007 − 04 7 Se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes. 2-1. S ym bol es u t ilisés DANGER! − Indique une situation dangereuse qui si on l’évite pas peut donner la mort ou des blessures gra[...]

  • Page 10

    OM-217 769 Page 6 Il reste une TENSION DC NON NÉGLIGEABLE dans les sources de soudage onduleur quand on a coupé l’alimentation. D Arrêter les convertisseurs, débrancher le courant électrique et décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie Entretien avant de toucher les pièces. DES PIÈCES CH[...]

  • Page 11

    OM-217 769 Page 7 LES ACCUMULA TIONS DE GAZ risquent de provoquer des blessures ou même la mort. D Fermer l’alimentation du gaz protecteur en cas de non-utilisation. D V eiller toujours à bien aérer les espaces confi- nés ou se servir d’un respirateur d’adduction d’air homologué. LES CHAMPS MAGNETIQUES peuv- ent affecter des implants m[...]

  • Page 12

    OM-217 769 Page 8 LES FILS DE SOUDAGE peuvent provoquer des blessures. D Ne pas appuyer sur la gâchette avant d’en avoir reçu l’instruction. D Ne pas diriger le pistolet vers soi, d’autres per- sonnes ou toute pièce mécanique en enga- geant le fil de soudage. DES ORGANES MOBILES peuvent provoquer des blessures. D S’abstenir de toucher d[...]

  • Page 13

    OM-217 769 Page 9 2-5. P r i nc ip al e s no r m e s de sé c ur i té Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www .global.ihs.com). Recommended Safe Practices for the Preparation for W elding and Cut- ting of Containers and Piping , Amer[...]

  • Page 14

    OM-217 769 Page 10[...]

  • Page 15

    OM-217 769 Page 1 1 SECTION 3 − DEFINITIONS 3-1. Manufacturer ’ s W arning Label Definitions W arning! W atch Out! There are possible hazards as shown by the symbols. 1 Electric shock from welding electrode or wiring can kill. 1.1 W ear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves. 1.2 Protect [...]

  • Page 16

    OM-217 769 Page 12 > 60 s V S-179 190-A V V 1 Warning! W atch Out! There are possible hazards as shown by the symbols. 2 Electric shock from wiring can kill. 3 Disconnect input plug or power before working on machine. 4 Hazardous voltage remains on input capacitors after power is turned off. Do not touch fully charged capacitors. 5 Always wait 6[...]

  • Page 17

    OM-217 769 Page 13 3-2. Manufacturer ’ s Rating Label 223 643-B 3-3. Symbols And Definitions A Amperage Panel Alternating Current (AC) V V oltage Output Circuit Breaker Remote On Of f Gas Tungsten Arc W elding Negative V oltage Input Direct Current (DC) Positive Inductance Protective Earth (Ground) Constant Current Constant V oltage Foot Control [...]

  • Page 18

    OM-217 769 Page 14 SECTION 4 − INST ALLA TION 4-1. Specifications Rated W elding Output V oltage Range Amperage Range Maximum Open-Circuit V oltage DC IP Rating Amperes Input at Rated Load Output 50/60 Hz Output Range Range V o l tage DC 400 V KV A KW 300 A @ 32 V olts DC, 60% Duty Cycle 10 − 35 5 − 400 90 23 17.0 (0.15*) 12.4 (0.09*) 1 1.5 ([...]

  • Page 19

    OM-217 769 Page 15 4-3. V olt-Ampere Curves va_curve1 4/95 − SA-178 652 / SA-178 653 V olt-ampere curves show minimum and maximum voltage and amper- age output capabilities of unit. Curves of other settings fall be- tween curves shown. A. CC Mode B. CV Mode ARC CONTROL[...]

  • Page 20

    OM-217 769 Page 16 4-4. Dimensions And Weight Hole Layout Dimensions 24 i A E A 1 1-3/4 in (298 mm) 24 in (610 mm) G F B 1-1 1/16 i n (42 mm) 17 in (432 mm) C 15-3/4 in (400 mm) D C D 19-3/32 in (485 mm) 12-1 / 2 in C E 8-1 1/16 i n (221 mm) 12 - 1/2 in (318 mm) F 1-17/32 in (39 mm) 804 801-A B G 1/4-20 UNC -2B thread W eight 76 lb (34.6 kg) 4-5. S[...]

  • Page 21

    OM-217 769 Page 17 4-6. W eld Output T erminals And Selecting Cable Sizes ! ARC WELDING can cause Electromagnetic Interference. T o reduce possible interference, keep weld cables as short as possible, close together , and down low , such as on the floor . Locate welding operation 100 meters from any sensitive electronic equipment. Be sure this weld[...]

  • Page 22

    OM-217 769 Page 18 4-7. Remote 14 Receptacle Information Socket* Socket Information 24 VOL TS AC A 24 volts ac. Protected by circuit breaker CB2. AJ B K I 24 VOL TS AC B Contact closure to A completes 24 volts ac con- tactor control circuit. B I C L NH 1 15 VOL TS AC I 1 15 volts ac. Protected by circuit breaker CB1. C D M G E F 1 15 VOL TS AC J Co[...]

  • Page 23

    OM-217 769 Page 19 4-9. Connecting 3-Phase Input Power ST-144 221 / ST -801 192 / 803 766-A ! Installation must meet all National an d Local Codes − have only quali- fied persons make this installation. ! Disconnect and lockout/tagout in- put power before connecting input conductors from unit. ! Always connect green or green/ yellow conductor to [...]

  • Page 24

    OM-217 769 Page 20 SECTION 5 − OPERA TION 5-1. Front Panel Controls 1 Power On/Of f Switch . The fan motor is thermostatically controlled and only runs when cooling is needed. 2 V oltmeter (see Section 5-2) 3 Ammeter (see Section 5-2) 4 V oltage/Amperage Adjustment Control 5 Mode Switch Th e Mode switch setting determines both the process and out[...]

  • Page 25

    OM-217 769 Page 21 5-2. Meter Functions . The meters display the actual weld output values for approximately three seconds after the arc is broken. Mode Meter Reading At Idle Scratch Start TIG (GT AW) Actual V olts (OCV) Preset Amps VA 80.0 85 Lift-Arc TIG (GT AW) VA Blank Preset Amps 7.5 85 TIG (GT AW) Blank Preset Amps VA 85 MIG (GMAW) Preset V o[...]

  • Page 26

    OM-217 769 Page 22 5-3. Mode Switch Settings . Th e SMA W modes provide the Adaptive Hot Start ™ feature, which automatically increases the output amperage at the start of a weld should the start require it. This eliminates electrode sticking at arc start. Mode Output Control Scratch Start TIG (GT AW) Select: or Amp W eld Lift-Arc TIG (GT AW) Sel[...]

  • Page 27

    OM-217 769 Page 23 5-4. Lift-Arc TIG Procedure With Process Switch in the Lift-Arc TI G position, start an arc as follows: 1 TIG Electrode 2 W orkpiece T ouch tungsten electrode to work- piece at weld start point, hold electrode to workpiece for 1-2 seconds , and slowly lift electrode. An arc will form when electrode is lifted. Normal open-circuit [...]

  • Page 28

    OM-217 769 Page 24 SECTION 6 − MAINTENANCE & TROUBLESHOOTING 6-1. Routine Maintenance ! Disconnect power before maintaining. . Maintain more often during severe conditions. 3 Months Replace Damaged Or Unreadable Labels Replace Cracked T orch Body Repair Or Replace Cracked Cables Repair Or Replace Cracked Cables And Cords Clean And Tighten W e[...]

  • Page 29

    OM-217 769 Page 25 6-3. V oltmeter/Ammeter Help Displays . Al l directions are in reference to the front of the unit. All circuitry referred to is lo- cated inside the unit. 1 Help 0 Display Indicates a shorted thermistor R T2 on the left side of the unit. If this display is shown, con- tact a Factory Authorized Service Agent. 2 Help 1 Display Indi[...]

  • Page 30

    OM-217 769 Page 26 6-4. T roubleshooting T rouble Remedy No weld output; unit completely inop- erative Place line disconnect switch in On position (see Section 4-9). era ti ve. Check and replace line fuse(s), if necessary , or reset circuit breaker (see Section 4 -9). Check for proper input power connections (see Section 4-9). No weld output; meter[...]

  • Page 31

    OM-217 769 Page 27 SECTION 7 − ELECTRICAL DIAGRAM 217 766-B Figure 7-1. Circuit Diagram For W elding Power Source[...]

  • Page 32

    OM-217 769 Page 28 SECTION 8 − P ARTS LIST 803 687-C 58 62 61 60 59 20 57 55 53 52 3 2 1 51 50 10 9 8 19 14 44 43 42 41 11 40 39 37 32 31 30 23 22 21 20 18 17 16 15 13 7 11 12 6 49 48 47 46 45 38 36 35 34 9 12 29 28 27 26 25 56 54 24 4 5 Figure 8-1. Parts Assembly[...]

  • Page 33

    OM-217 769 Page 29 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Parts Assembly Quantity 1 +175 148 Wrapper 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 256 Insulator , Side 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Page 34

    OM-217 769 Page 30 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Parts Assembly (Continued) Quantity 47 175 132 Base 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 PC3 219 820 Circuit Card Assy , Front Panel & Display W/Program[...]

  • Page 35

    Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 2007 − 01 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor . The expe[...]

  • Page 36

    PRINTED IN USA © 2007 Miller Electric Mfg. Co. 2007 − 01 Miller Elect ric Mfg. Co. An Illinois T ool Wo rks Compan y 1635 West S pencer S treet Applet on, WI 5 4914 US A International He adquarter s − US A USA Phone: 920-735-4505 Aut o-At tended USA & Canada F AX : 920-735-4134 Int ernati onal F AX: 9 20-735-4125 European Headqua rters −[...]