Mazda 2005 Tribute manual

Introduction 4 Instrument Cluster 14 W arning and control lights 14 Gauges 19 Entertainment Systems 21 AM/FM stereo with single CD 21 AM/FM stereo with in-dash six CD 25 Climate Controls 31 Manual heating and air conditioning 31 Lights 33 Headlamps 33 T urn signal control 37 Bulb replacement 38 Driver Controls 43 W indshield wiper/washer control 43[...]

Seating and Safety Restraints 70 Seating 70 Safety restraints 78 Air bags 93 Child restraints 107 Tires, Wheels and Loading 1 19 T ire Information 122 T ire Inflation 123 Changing tires 126 Lug Nut T orque 135 V ehicle loading 145 T railer towing 152 Recreational towing 157 Driving 158 Starting 158 Brakes 162 T ransmission operation 167 Roadside Em[...]

Maintenance and Specifications 216 Engine compartment 224 Engine oil 226 Battery 230 Fuel information 238 Air filter(s) 252 Refill capacities 253 Engine data 255 Accessories 259 Index 260 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or t[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by a bold W ARNING statement. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, it [...]

BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1,000 miles (1,600 km) of driving, vary speeds frequently . This is necessary to give the moving parts a chance to break in. SPECIAL NOTICES Event Data Recorder The computer in your vehicle is capable of recording detailed data potentially includin[...]

Emission warranty The New V ehicle Limited W arranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties. For a detailed description of what is covered and what is not covered, refer to the W arranty Guide that is provi[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner ’ s Guide Protecting the Environment Fasten Safety Belt Air Bag-Front Air Bag-Side Passenger Airbag Off Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake F[...]

V ehicle Symbol Glossary Power W indows Power W indow Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine Air Filter Powertrai[...]

INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing. Mazda may change the contents without notice. REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Introduction 10[...]

REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Instrument Cluster Instrument Cluster 11[...]

Instrument cluster (pg. 14) W indshield wiper/washer control (pg. 43) Driver air bag (pg. 93) Speed controls* (pg. 51) Instrument panel dimmer/dome light control (pg. 35) Hood release handle (pg. 223) Power mirror control* (pg. 50) Headlamp and turn signal control (pg. 33) Manual tilt steering column lever (pg. 45) * if equipped REVIEW COPY 2005 Ma[...]

Passenger airbag off indicator (pg. 97) Hazard flasher control (pg. 183) Audio system (pg. 21) Cigarette lighter* Fog lamp control* (pg. 33) Climate controls (pg. 31) Rear window defroster control (pg. 31) Auxiliary power point (pg. 48) Air conditioning control (pg. 31) *if equipped REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle ’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains[...]

2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or a[...]

It may take a long period of time for the system to detect an improperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and Specifications chapter . Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON p[...]

Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by an authorized Mazda dealer . A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A chime wil[...]

Anti-theft system: Flashes when the Securilock 娂 Passive Anti-theft System has been activated. Refer to SecuriLock 娂 passive anti-theft system in the Locks and Security chapter . Speed control: Illuminates when the speed control is activated. T urns off when the speed control system is deactivated, refer to the Driver Controls chapter . Door aj[...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “ H ” and “ C ” ). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off [...]

Odometer: Registers the total miles (kilometers) of the vehicle. T rip odometer: Registers the miles (kilometers) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer . T achometer: Indicates the engine speed in revolutions p[...]

AM/FM STEREO SINGLE CD AUDIO SYSTEM — SATELLITE READY CAPABILITY 1. CD: T o begin CD play , insert a CD into the slot, label side up. The system will auto-load the CD and begin play after a short pause. The disc number and the track number will illuminate in the display . 2. MD/T APE: This control does not function on the base audio system. It wi[...]

3. CLOCK: Press and release CLOCK to alternate between the time and the audio display . The clock can be set at any time when the ignition switch is in the ACC or ON position. Press and hold CLOCK for approximately two seconds until a beep sound is heard. The clock ’ s current time will flash. Press SCAN adjust the hours. Press AUTO-M to adjust t[...]

Press the AM or FM1/2 control to select a frequency . Press and momentarily hold the AUTO-M (Auto memory) control. The system will beep. Press the AUTO-M (Auto memory) control to select from the stored stations. One stored station will be selected and played each time the control is pressed. The frequency and channel number will be displayed. NOTE:[...]

11. DISC : Press to skip forward to the beginning of the next CD. 12. DISC Press to skip back to the beginning of the previous CD. 13. V olume/ON/OFF: Press to turn the system on/off. T urn to adjust the volume. 14. Memory presets: Y our audio is equipped with six station memory preset controls. These controls can be used to select up to six preset[...]

17. SA T : Y our radio comes equipped with Satellite ready capability . This enables you to view the song titles, artist, and further information. The kit to enable Satellite reception is available through your dealer . Detailed Satellite instructions are included with the dealer installed kit. AM/FM STEREO SIX CD AUDIO SYSTEM — SATELLITE READY C[...]

3. CLOCK: Press and release CLOCK to alternate between the time and the audio display . The clock can be set at any time when the ignition switch is in the ACC or ON position. Press and hold CLOCK for approximately two seconds until a beep sound is heard. The clock ’ s current time will flash. Press SCAN adjust the hours. Press AUTO-M to adjust t[...]

AUTO-M: Press the FM/AM control to select auto memory tuning which allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Press the FM/AM control to select a frequency . Press and momentarily hold the AUTO-M (Au[...]

10. RPT : Press during CD play to listen to a selection repeatedly . RPT will illuminate in the display and the current selection will be repeated. Press again to disengage repeat play . 11. DISC : Press to skip forward to the beginning of the next CD. 12. DISC : Press to skip back to the beginning of the previous CD. 13. V olume/ON/OFF: Press to t[...]

TRACK: Press on the TRACK control to skip forward to the beginning of the next track. Press to skip back to the beginning of the current track. 16. LOAD: Press to load a CD. Press LOAD and a memory preset to load a CD into a specific slot. Press and hold LOAD to enter up to six CDs one at a time. 17. FM/AM: Press to enter radio mode and select a fr[...]

• T ighten very loose tapes by inserting a finger or pencil into the hole and turning the hub. • Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity or cold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after 10 ?[...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. A/C: Press to activate A/C. The indicator light will illuminate to indicate A/C is functioning. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief des[...]

W ARNING: Under some weather conditions, use of the recirculated air mode may lead to glass misting or fogging. Switch the air conditioner on and select the fresh air mode. Heated air can assist windscreen demisting. Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position. • [...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. BATTERY SAVER Y our vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF pos[...]

W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. High beams After turning the he[...]

INSTRUMENT P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. V ERTICAL AIM ADJUSTMENT 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meter) ?[...]

2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens. 3. T urn on the low beam headlamps to illuminate the wall or scree[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR position and any door is open. When[...]

The map lamp controls (without moon roof) are located on the dome lamp. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps. For models equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the button on either side of each map lamp to illuminate [...]

Function Number of bulbs T rade number Park/turn lamps (front) 2 3157 AK (amber) Headlamps 2 9003 (HB2) Rear stop/tail lamps 2 W21/5W Rear turn lamps 2 WY21W (amber) Rear license plate lamps 2 W5W Backup lamp 2 W21W Side repeater lamp 2 WY5W (amber) Fog lamp (if equipped) 2 H1 Cargo lamp 1 211-2 Center high-mount stop lamp 5 W5W Interior overhead l[...]

Replacing headlamp bulbs NOTE: This procedure can be difficult. Y our Mazda dealer has the proper tools, training and parts to perform this task. If you have difficulty with this procedure, visit your local Mazda dealer . 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. W ARNING: Handle a halogen bulb carefully and k[...]

Replacing side repeater bulbs 1. T urn the headlamp switch to off. 2. Carefully pry the lamp assembly away from the fender . 3. Rotate the bulb socket counterclockwise to remove it from the lamp assembly . 4. Pull the bulb straight out. Reverse steps to reinstall bulb(s). Replacing foglamp bulbs For bulb replacement, see your authorized Mazda deale[...]

Replacing license plate lamp bulbs 1. Push the license plate lamp assembly to the right and remove the assembly (located above the license plate) from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly and turn[...]

MUL TI-FUNCTION LEVER W indshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF . For high speed wiper operation, move control down three positions from OFF . Mist function: T o activate mist[...]

Rear window wiper/washer controls For intermittent operation of rear wiper , rotate end of control upward to the position. For normal speed rear wiper operation, rotate control upward to ON. T o activate the rear washer , rotate the control to the position and release. Windshield wiper blades Check the wiper blades for wear at least twice a year or[...]

Changing the wiper blades 1. Pull the wiper arm away from the vehicle. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. 3. Replace wipe[...]

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle ’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment ca[...]

Note: The length of the rubber actuator (1) is critical. Use care in cutting it to length. If the rubber actuator (1) is cut too much the aftermarket transmitter (6) will not activate the garage door opener . If the rubber actuator (1) is cut too long, the storage compartment door (3) will not close properly . Excessive force to close the storage c[...]

AUXILIARY POWER POINT (12VDC) W ARNING: Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet for this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The[...]

W ARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. The ignition must be in the ON position to adjust the power windows. Press and hold the bottom part of the rocker switch to open the window . Press and hold the top part of t[...]

W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows or moon roof. They may seriously injure themselves. MIRRORS Power side view mirrors T o adjust your mirrors: 1. Rotate the control, located on the instrument panel left of the steering wheel, clockwise to adjust the right mirror and rotate [...]

SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h). W ARNING: Using cruise control in the following conditions could cause you to lose control of the vehicle: • Heavy or unsteady t[...]

• If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. Resuming a set speed Press the RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RSM control will not work if the vehicle speed is not faster than 30 mph ([...]

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST control until you get to the desired speed, then release the control. Y ou can also use the CST control to operate the T ap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h)[...]

FUEL FILLER DOOR RELEASE HANDLE T o open the door , pull up the handle located next to the front left corner of the driver ’ s seat. MOON ROOF (IF EQUIPPED) T o operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. T o stop motion at any time [...]

CENTER CONSOLE Y our vehicle is equipped with a variety of console features. These include: 1. Power point 2. Cupholders 3. Utility compartment 4. Ash cup (if equipped) W ARNING: Use only soft cups in the cupholder . Hard objects can injure you in a collision. CARGO SHADE (IF EQUIPPED) If your vehicle has a cargo shade, you can use it to cover item[...]

W ARNING: Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of vehicle in the case of a sudden stop or collision. LIFTGATE T o open the rear window , pull the right side of the liftgate handle. T o open the liftgate, pull the left side of the liftgate handle. • Do not open the liftgate or liftgate[...]

LUGGAGE RACK The maximum load for the roof rack is 100 lbs (45 kg), evenly distributed on the crossbars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the crossbars (if equipped) as possible. Always use the adjustable tie down loops to secure the load. T o adjust the cross-bar (if equipped) posi[...]

KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency . Y our keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer . Refer to the Secur[...]

7. T urn the ignition from the 3 (RUN) position to the 1 (OFF/LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking T wo step door unlocking 1. T urn the key in the door cylinder to unlock the driver ’ s door . Note: The interior[...]

Childproof door locks • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatically set the lo[...]

The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote locking and unlocking features will operate independent of the ignition position; however , the panic feature will only operate when the ignition is in the 1 (OFF/LOCK) or 2 (ACCESSORY) position. If there are problems with the remote entry system, make[...]

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapt[...]

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the batt[...]

T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. T urn the key from the 1 (OFF/LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN) position. 5. The door[...]

Illuminated exit • The interior lights will illuminate when the key is removed from the ignition. The lamps automatically turn off after 25 seconds. The dome and cargo lamp controls must not be set to the OFF position for the illuminated exit system to operate. SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is a[...]

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. If this occurs, the vehicle should be taken to an authorized Mazda dealer for service. Automatic arming The vehicle is armed immediately after switching the ignition to the 2 (ACCESSORY) position. The l[...]

W ARNING: If an unprogrammed key is used in the ignition it will cause a “ no start ” condition. Programming spare keys Y ou can program your own coded keys to your vehicle. T ips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 娂 keys. • Y ou must have two previously programmed coded keys (keys that alread[...]

7. W ithin twenty seconds of turning the ignition to the 1 (OFF/LOCK) position and removing the previously programmed coded key , insert the new unprogrammed key (new key/valet key) into the ignition. 8. T urn the ignition from the 1 (OFF/LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds bu[...]

When you lock the vehicle using any of the methods above: • the park/turn lamps will flash once to indicate the hood, each door and the liftgate are closed. • the park/turn lamps will not flash if the hood, any door or the liftgate are open. Once all doors, hood and liftgate are closed, the park/turn lamps will flash to confirm the alarm will b[...]

SEA TING Adjustable head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Push side co[...]

W ARNING: Sitting in a reclined position while the vehicle is moving is dangerous because you don ’ t get the full protection from seat belts. During sudden braking or a collision, you can slide under the lap belt and suffer serious internal injury , or in a rear end collision you could fly up and out of the vehicle. For maximum protection, sit w[...]

Adjusting the front power seat (if equipped) W ARNING: Never adjust the driver ’ s seat or seatback when the vehicle is moving. Y ou could move out of position to control the vehicle. Then a serious accident could occur . Sudden braking or a collision could cause serious injury . Adjust the seat only when the vehicle is stopped. W ARNING: Do not [...]

Move the control in the directions shown to move the seat forward, backward, up or down. Heated seats (if equipped) T o operate the heated seats: • Push the control located on the seat to activate. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position. When activated, they will turn off automaticall[...]

Push control to lower head restraint. Folding down rear seats (60/40 split bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraint under the front seat for storage. 3. Pull the seat release control. NOTE: Make sure the floor is clear of all objects before folding the seat. REVIEW COPY 2005 Mazda Tribute (j14) , Owners G[...]

4. Flip seat forward. Attach the seatbelt web snap button to the quarter trim panel snap button. This will assure that seatbelt does not get caught by staying out of the seat back folding path. 5. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat. This is common for both 60% and 40% seatbacks. NOTE: When t[...]

6. Rotate seatback down into load floor position. Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and the RED seat unlatched indicator on release paddle is not[...]

W ARNING: Make sure seat belt buckle heads are through elastic holders on seat backs. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs. T o remove the rear cushio[...]

SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safet[...]

Driver and passenger dual-stage air bag supplemental restraints The dual-stage air bags offer the capability to tailor the level of air bag inflation energy . A lower , less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Air bag supplemental restraint[...]

The front passenger sensing system can automatically turn off the passenger front air bag. The system is designed to help protect small (child size) occupants from air bag deployments when they are improperly seated or restrained in the front passenger seat contrary to proper child-seating or restraint usage recommendations. Even with this technolo[...]

Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the W arning light section in the Instrument cluster chapter . Routine maintenance of the Personal Safety System is not required. The Restraints contro[...]

W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using[...]

W ARNING: All safety belts should be checked for proper function. Additionally , if the front air bags have deployed, the front pretensioners have also deployed and both front restraints must be replaced. After any vehicle collision, the safety belt system at all outboard seating positions (except driver , which has no “ automatic locking retract[...]

2. T o unfasten, push the release button and remove the tongue from the buckle. All safety belts in the vehicle are combination lap and shoulder belts. The passenger safety belts have two types of locking modes described below: V ehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movem[...]

How to use the automatic locking mode for use with child safety seats • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic lock[...]

W ARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which doesn ’ t have this feature) must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly . In addition, all seat belts should be checked for p[...]

When the side-curtain air bags (if equipped) and/or the front airbags are activated, the safety belt pretensioners for the driver and right front passenger seating positions will be activated when the respective seatbelt is properly buckled. W ARNING: The driver and the right front passenger seat belt system (including retractors, buckles and heigh[...]

Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. NOTE: Do not use extensions to change the fit of the shoulder belt across the torso. Safety bel[...]

Both the driver ’ s and passenger ’ s safety belt usages are monitored and either may activate the BeltMinder feature. The warnings are the same for the driver and the front passenger . If the BeltMinder warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activa[...]

Reasons given... Consider ... ⬙ Crashes are rare events ⬙ 36,700 crashes occur every day . The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. ⬙ I ’ m not going far ⬙ 3o f4 fatal crashes occur within 25 miles of home. ⬙ Belts are[...]

Reasons given... Consider ... ⬙ I have an air bag ⬙ Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. ⬙ I ’ d rather be thrown clear ⬙ Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, [...]

W ARNING: T o reduce the risk of injury , do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE) 2. W ait until the safety belt warning light turns off. (Approximately 1 minute) • Step 3 must be completed within 50 seconds after the safety [...]

NOTE: If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for inspection. Inspect the safety belts to make sure there are no nicks, tears or cuts, replacing if necessary . Check all automatic locking retractors on all outboard seating positions as well as the automatic locking mode for child safety seats on t[...]

Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. W ARNING: Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim c[...]

W ARNING: Do not put anything on or over the air bag module including hands or feet. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury . W ARNING: Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint Systems or its [...]

W ARNING: Air bags can kill or injure a child in a child seat NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Secure the seat and the child in it properly . How does the air bag supplemental restraint system work? The air bag SRS is d[...]

hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important[...]

The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor V ehicle Safety Standard (FMVSS) 208 and is designed to turn off the front passenger ’ s frontal air bag if: • The front passenger seat is unoccupied, • The system determines that a small child is present in a rear -facing child seat that is pr[...]

child in the front seat against all advice, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer ’ s directions. The front passenger sensing system is designed to enable (may inflate) the right front passenger ’ s frontal air bag anytime the system senses t[...]

Objects Pass Airbag Off Indicator Light Passenger Airbag Empty seat Unlit Disabled Small (i.e. 3 ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty seat, Small or medium object with safety belt buckled Lit Disabled In case there is a problem with the passenger sensing syst[...]

W ARNING: Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles For disposal of safety belt pretensioners, air bags, or air bag equipped vehicles, see your authorized Mazda dealership. Air bags MUST BE disposed of by qualified personnel. W ARNING: Disposing of an air ba[...]

How does the side air bag system work? The design and development of the side air bag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Air Bag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side [...]

to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision causes sufficient lateral deceleration. W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side air bag has deployed, the air bag will not function again.[...]

Side-curtain air bag system (if equipped) Y ou can easily confirm if your vehicle has side-curtain air bags by looking inside the vehicle up at the upper ⬙ B ⬙ pillar where you will see an embossed ⬙ AIRBAG ⬙ label. W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a d[...]

W ARNING: T o reduce risk of injury , do not obstruct or place objects in the deployment path of the inflatable side-curtain air bags (if equipped). How do the side-curtain air bags (if equipped) work? The side-curtain air bags (if equipped) consists of the following: • An inflatable nylon curtain with a gas generator concealed behind the headlin[...]

lateral collisions or rollover events, the side-curtain air bags will be activated, regardless of which seats are occupied. In certain rollover events, the side-curtain air bag (if equipped) on both sides of the vehicle will be inflated, regardless of which seats are occupied. The side-curtain air bags (if equipped) are designed to inflate between [...]

Determining if the side-curtain airbags are operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter . Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of th[...]

NOTE: Always follow the instructions and warnings that come with any infant or child restraint you might use. W ARNING: When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Chi[...]

T o improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Mazda recommends use of a belt-positioning booster seat. Booster seats position a child so that safety belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably . Booster seats also ma[...]

T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child ’ s head (top of ear level)[...]

W ARNING: Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never put the shoulder belt under a child ’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. W ARNING: Never use pillows, books, or towels to boost a[...]

• Put the safety belt in the automatic locking mode. Refer to Automatic locking mode . Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats wit[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer ’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the [...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]

3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. W ARNING: If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. If the safety seat is not anchored properly , the risk of a c[...]

Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use seat belts to attach the[...]

The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. The LA TCH anchors are below the locator symbols on the seatback. Follow the child seat manufacturer ’ s instructions to properly install a child seat with LA TCH attachments. W ARNING: Attach LA TCH lower attachments [...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on shifting procedures and maintenance can be found in your Owner ’ s Guide .Y o u should become thoroughly familiar with this information before you operate your vehicle. On some 4[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV ’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so vers[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the ac[...]

Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry . • T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of man[...]

Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended[...]

Maximum Permissible Inflation Pressure is the tire manufactures ’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer ’ s recommended cold inflation pressure which can be found on either the tire label or certification label which is locate[...]

TIRE REPLACEMENT REQUIREMENTS Y our vehicle is equipped with tires designed to provide a safe ride and handling capability . W ARNING: Only use replacement tires and wheels that are the same size and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Mazda. Use of any tire or wheel not recomm[...]

When driving with the T -type/mini-spare tire do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • T ow a trailer • Use snow chains on the end of the vehicle with the T -type/mini spare tire • Use more than one T -type/mini spare tire at a time • Use commercial c[...]

• Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capabil[...]

W ARNING: If the vehicle slips off the jack, you or someone else could be seriously injured. 1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission). 2. Set the parking brake and turn engine off. 3. Block the diagonally opposite wheel. Removing the jack[...]

Remove the lug wrench from the jack in order to remove the spare tire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through the access hole in the rear bumper . 2. T urn the handle counterclockwise and lower the spare tire until it can be slid rearward and the cable is slack. 3. Slid[...]

5. Use the lug wrench to remove the lug nut from the spare tire tether . 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached V elcro strap (2) to tie the tether end to the winch actuator shaft (if equipped). Changing the flat tire 8. Loosen each wheel lug nut one-[...]

Before placing the jack under the vehicle, NOTE the jack locations: • Front • Rear REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Tires, Wheels and Loading 132[...]

9. Lower the jack from its stored height to fit under the jacking notches. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Never use the differentials as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your[...]

14. Reinstall the jack and tools in the cargo area. T o replace jack in vehicle, guide the jack bottom first in trim opening and position in bracket, secure retention clip on upper part of jack and close thumbscrew . Make sure the jack is fastened so it does not rattle when you drive. Stowing the flat/spare tire Note: Failure to follow spare tire s[...]

5. T urn the jack handle clockwise until the tire is raised to its original position underneath the vehicle. The effort to turn the jack handle increases significantly as the tire contacts the frame. The spare tire carrier will ratchet when the tire is in the fully stowed position. The spare tire carrier has a built-in ratchet feature that will not[...]

W ARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the whe[...]

5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire ’ s load index. It is an index that relates to how much weight a tire can carry . Y ou may find this information in your Owner ’ s Guide . If not, contact a local ti[...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “ DOT ” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For e[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers ’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer ’ s recommended cold inflation pressure which can be found on either the tire label or certification label wh[...]

Information on “ T ” type tires “ T ” type tires have some additional information beyond those of “ P ” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and[...]

TIRE CARE Improper or inadequate vehicle maintenance can also cause tires to wear abnormally . Here are some of the important maintenance items: Tire wear Measure and inspect the tire tread on all your tires periodically . Advanced and unusual tire wear can reduce the ability of tread to grip the road in adverse (wet, snowy , etc.) conditions. Visu[...]

Safety practices Driving habits have a great deal to do with your tire mileage and safety . • Observe posted speed limits • A void fast starts, stops and turns • A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rap[...]

Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by a qualified technician at a Mazda dealer . Front wheel drive (FWD) vehicles and those with an independent rear suspension require alignment of all four wheels. The tire should also be balanced periodically . An unbalanced tire a[...]

• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mech[...]

Follow these guidelines when using snow tires and traction devices: • SAE class “ S ” cables should ONL Y be used on the front axle for P235/70R16 tires. • Do not use tire chains on aluminum wheels. Chains may chip the wheels. • Install cables or chains securely , verifying that the chains do not touch any wiring, brake lines or fuel line[...]

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver ’ s door . Look for “ THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb. ” for maximum payload. The payload liste[...]

Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. REVIEW COPY 2005 Maz[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the driver ’ s door or B-Pillar . The total load on each axle must never exceed its GA WR. W ARNING: Exceeding the Safety Certification Label ax[...]

GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the driver ’ s door or B-Pillar . The GVW must never exceed the GVWR. W ARNING: Exceeding the Safety Certification [...]

Maximum Loaded T railer W eight – is the highest possible weight of a fully loaded trailer the vehicle can tow . It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10 – 15% (conventional trailer) or king pin weight of 15 – 25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult yo[...]

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the avail[...]

Special loading instructions for owners of pickup trucks and utility-type vehicles W ARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter . W ARNING: Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds a[...]

• Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter . • Service your vehicle more frequently if you tow a trailer . Refer to the “ Scheduled Maintenance ” section of this manual. • Do not tow a trailer until your vehicle has been driven at least 500 miles (800 km). • Refer to the instruc[...]

4x2 GCWR (Gross Combined W eight Rating)/T railer W eights .The T ribute is capable of pulling the maximum trailer weight(s) as specified above. Certain states require electric trailer brakes for trailers over a specified weight. The T ribute vehicle electrical system is not equipped to accommodate electric trailer brakes. 4x4 GCWR (Gross Combined [...]

T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in: • engine damage • transmission damage • structural damage • loss of control • personal injury Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See y[...]

Driving while you tow When towing a trailer: • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. ?[...]

Replace the rear axle lubricant any time the axle has been submerged in water . Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required. Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the wate[...]

STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. 4. ST ART , cranks the engine. Release the ke[...]

W ARNING: If you smell exhaust fumes inside your vehicle, have your authorized Mazda dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine ’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to w[...]

If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. Note: If the driver ’ [...]

1. T urn the key to 4 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 3 (ON). 2. When the engine starts, release the key , then release the accelerator pedal gradually as the engine speeds up. 3. After idling for a few seconds, apply the brake, shift into gear and drive. Note: If the [...]

Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision. W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause ca[...]

Four-wheel anti-lock brake system (ABS) Since your vehicle is equipped with an Anti-lock Braking System (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and[...]

Brake Assist The Brake Assist system provides full braking force during panic braking situations. It detects a rapid application of the brake pedal and maximizes the amount of brake booster assist, helping the driver to achieve maximum braking pressure. Once a panic brake application is detected, the system will remain activated as long as the brak[...]

W ARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergenc[...]

• uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment PREPARING TO DRIVE YOUR VEHICLE Y our vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances. These special design features, such as larger tires and increa[...]

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the RUN position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the RUN [...]

W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. W ARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized Ma[...]

Understanding the gearshift positions of the 4 – speed automatic transaxle This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle ’ s battery has been disconnected for any type of service or repair , the transmission will nee[...]

W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).[...]

2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to D (Overdrive), move the gearshift lever into the D (Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transaxle to downshift to second gear at the appropriate vehicle speed. 1 (Firs[...]

MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch V ehicles equipped with a manual transaxle have a starter interrupt interlock that prevents cranking of the engine unless the clutch pedal is depressed. When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in the neutral position. 2. Hold down the brake pedal[...]

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fuel economy) 1-2 14 mph (22 km/h) 2-3 25 mph (40 km/h) 3-4 34 mph (55 km/h) 4-5 44 mph (70 km/h) Upshifts when cruising (recommended for best fuel economy) 1-2 12 mph (19 km/h) 2-3 19 mph (31 km/h) 3-4 29 mph ([...]

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Set the parking brake. 3. Depress the clutch, then shift into 1 (First). 1 24 R 3 5 1 24 R 3 5 REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Driving 174[...]

4. T urn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key . W ARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) W ARNING: For important information regarding safe operation of t[...]

• Blinks several times every minute when 4WD system requires service. Please bring your vehicle to your local dealer for service. Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow , mud and rough terrain and have operating characteristics that are somewhat different from conventional ve[...]

• It often may be less risky to strike small objects, such as highway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or rollover . Remember , your safety and the safety of others should be your primary concern. W ARNING: V ehicles wit[...]

W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “ over -driving ” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid [...]

A void excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember , you may be able to back out the way you came if you proceed with caution. Mud and water NOTE: • If you must drive through high water , drive slowly . T raction or [...]

“ T read Lightly ” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Mazda Motor Corporation joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “[...]

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can ’ t [...]

• 4WD vehicles should be driven with traction devices as referred to in Using snow tires and traction devices in the T ires, Wheels and Loading chapter . Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carryi[...]

HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is off. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard [...]

FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage r[...]

Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover . REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_Englis[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A* T railer tow park lamps 2 5A* Radio (illumination) 3 15A* Front and rear park lamps 4 10A* Ignition switch 5 2A* Powertrain Control Module (PCM relay), Fuel pump relay , Main fan relay , High/Low speed fan relay 2, P A TS module 6[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 7 10A* Instrument cluster , Diagnostic connector , Power mirror switch, Radio 8 — Not used 9 30A** Power door locks, Power seats 10 15A* Heated mirrors 11 15A* Sunroof 12 — Not used 13 — Not used 14 — Not used 15 30A** Power windows 16 15A* Subwoofer 17 15A* Lo[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 32 10A* Brake-T ransmission shift lock 33 15A* Air bag module, Passenger Air bag Deactivation (P AD) indicator lamp, Occupant Classification Sensor (OCS) 34 5A* ABS module, Evac and Fill, Speed control 35 5A* Heated seats module, 4WD * Mini fuse ** Cartridge fuse Power[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 25A* I/P fuse panel (RUN/ST ART) 2 25A* Headlamp power 3 25A* High beams, T urn signals, Interior lamps, Headlamp power 4 5A* Keep Alive Power (KA PWR) 5 15A* Heated Exhaust Gas Oxygen (HEGO) sensors 6 20A* Fuel pump 7 40A** RUN/ACC[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 19 40A** Accessory delay relay - Subwoofer and 4WD, Low beam 20 60A** ABS 21 40A** Horn, CHMSL, Cluster , Power locks and power seats 22 40A** (14) Cooling fan 50** (V6) 23 40A** Rear defroster , Park lamps relay 24 40A** (14) High/Low speed fan 50** (V6) 25 — Shunt R2 — PCM[...]

W ARNING: Steam from an overheated engine is dangerous. The escaping steam could seriously burn you. Open the hood ONL Y after steam is no longer escaping from the engine. 4. Check whether coolant or steam is escaping from under the hood or from the engine compartment. • If steam is coming from the engine compartment: do not go near the front of [...]

W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability . Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy . As a result, [...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Roadside Emergencies 19[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle ’ s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. W ARNING: Do not connect the end of the second cable to the negative (-) terminal of [...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle ’ s batte[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle ’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle ’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a sli[...]

On 4WD vehicles, it is required that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground. If the vehicle is towed by other means or incorrectly , vehicle damage may occur . In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed [...]

CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or [...]

6. Y our question(s) If you live outside the U.S.A., please contact your nearest Mazda Distributor . CUSTOMER ASSISTANCE (CANADA) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. In our experience, any ques[...]

The Department, in cooperation with the local Mazda Service Representative, will review the case to determine if everything possible has been done to ensure your satisfaction. Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer ’ s service facilities. personnel and equipment. W e urge you t[...]

REGIONAL OFFICES Regional Offices Areas Covered Mazda Canada Inc. W estern Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303 – 5670 Alberta, British Columbia, Manitoba, Saskatchewan, Y ukon Mazda Canada Inc. Central Region 305 Milner A venue Suite 400 Scarborough, Ontario. M1B 3V4 1 (800) 263 – 4680 Ontario Mazda Canada Inc. [...]

STEP 2 If, after following STEP 1, you feel the need for further assistance, please contact your area ’ s Mazda representative (Indicated on the next page). Please help us by providing the following information: 1. Y our name, address, and telephone number 2. Y ear and model of vehicle 3. V ehicle Identification Number (17 digits, noted on your r[...]

CANADA Mazda Canada, Inc. 305 Milner A venue, Suite 400 Scarborough, Ontario M1B 3V4 Canada TEL: 1 (800) 263 – 4680 (in Canada) (416) 609 – 9909 (outside Canada) PUERTO RICO Plaza Motors Corp. (Mazda de Puerto Rico) P .O. Box 362722, San Juan, Puerto Rico 00936 – 2722 TEL: (787) 788 – 9300 GUAM (d.b.a. T riple J. Enterprises, Inc.) P .O. Bo[...]

W ARNING: Installation of Non-Genuine Parts or Accessories: Installation of non-genuine parts or accessories could be dangerous. Improperly designed parts or accessories could seriously affect your vehicle ’ s performance or safety system. This could cause you to have an accident or increase your chances of injuries in an accident. Always consult[...]

The differences may make it difficult or even impossible for your vehicle to receive satisfactory servicing in other countries. W e strongly recommend that you NOT take your Mazda outside the United States. However , in the event that you are moving to Canada permanently , Mazda vehicles built for use in the United States could be eligible for expo[...]

Please refer to your manufacturers warranty booklet for more information. REPORTING SAFETY DEFECTS If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying your Mazda importer/distributor [...]

SERVICE PUBLICATIONS Factory-authorized Mazda service publications are available for owners who wish to do some of their own maintenance and repair . When requesting any of our publications through an Authorized Mazda Dealer , refer to the chart below . If they don ’ t have what you need in stock, they can order it for you. PUBLICA TION ORDER NUM[...]

California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. T wo or more repair attempts are made on the same n[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as an approved shampoo available from your Mazda dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “[...]

PAINT CHIPS Y our dealer has touch-up paint to match your vehicle ’ s color . T ouch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the[...]

• 2.3L DOHC I4 Engine • 3.0L DOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Cleaning 212[...]

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer . • For routine cleaning, use One Step W ash and W ax Concentrate, available at your authorized Mazda dealer . • If tar or grease spots are present, use Extra Strength T ar and Road Oil Removal, available at your[...]

INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then dry by wiping with a dry , soft, clean cloth. • Do not use household or glass cleaners as these may damage the finish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags (if equipped): • Remove dust and loose dirt with a vacuum cle[...]

UNDERBODY Flush the complete underside of your vehicle frequently . Keep body and door drain holes free from packed dirt. MAZDA CAR CARE PRODUCTS Y our Mazda dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are c[...]

INTRODUCTION Be extremely careful to prevent injury to yourself and others or damage to your vehicle when using this manual for inspection and maintenance. If you ’ re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer . Factory-traine[...]

NOTE: After the described period, continue to follow the described maintenance at the recommended intervals. SCHEDULE 1 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles[...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.5) (90) CHASSIS and BODY Brake lines, hoses and connections II I Disc brakes I I I I I[...]

SCHEDULE 2 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 [...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) Engine coolant (yellow) Replace at first 160,000 km (100,000 miles) or 60 months; after that, ev[...]

long-term reliability . *2 If the vehicle is operated under any of the following conditions, change the spark plugs every 60,000 miles (96,000 km) or shorter . a) Repeated short-distance driving. b) Extended periods of idling or low-speed operation. c) Driving for long periods in cold temperatures or extremely humid climates. *3 If this component h[...]

PRECAUTIONS WHEN SERVICING YOUR VEHICLE W ARNING: A hot engine is dangerous. If the engine has been running, parts of the engine compartment can become very hot. Y ou could be burned. Don ’ t inspect the coolant system or add coolant when the engine is hot. • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. ?[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod. REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil filler cap 9. Engine oil dipstick 10. W indshield washer fluid reserv[...]

3.0L DOHC V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10. W indshield washer fluid reservoir REVIEW COPY 2005 Mazda Tribute (j14) , Owners Guide (po[...]

WINDSHIELD WASHER FLUID Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter . W ARNING: If [...]

3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.3L I4 engine • 3.0L DOHC V6 engine 6. W ipe the indicator clean. Inser[...]

• If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN – MAX or ADD-FULL range. • 2.3L I4engine • 3.0L DOHC V6 engine • Oil levels above the MAX or FULL mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fu[...]

3. Recheck the engine oil level. Make sure the oil level is not above the MAX or FULL mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until it is seated. T o avoid possible oil loss, DO NOT operate [...]

It is recommended you use the appropriate Genuine Mazda oil filter (or another brand meeting Mazda specifications) for your engine application. BATTERY Y our vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climate[...]

W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. W ARNING: When lifting a plastic-cased battery , excessive pr[...]

NOTE: • The vehicle may need to be driven to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is disconnected or a new battery installed, the transmission must relearn its a[...]

60%, the engine parts could become damaged or not work properly . A 50 – 50 mixture of coolant and water provides the following: • freeze protection down to -34 ° F (-36 ° C). • boiling protection up to 265 ° F (129 ° C). • protection against rust and other forms of corrosion. • an accurate temperature readout from the engine coolant [...]

W ARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. W ARNING: Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it dif[...]

water to the “ FULL COLD ” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. W ARNING: T o reduce the risk of personal injury , make sure the engin[...]

If you have to add more than 1.0 quart (1.0 liter) of engine coolant per month, have your dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage). Recycled engine coolant Not all coolant recycling processes produce cool[...]

• Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. V ehicles driven yea[...]

When fail-safe mode is activated Y ou have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the[...]

W ARNING: Automotive fuels can cause serious injury or death if misused or mishandled. W ARNING: Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: W ARNING: Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can c[...]

• Be particularly careful if you are taking “ Antabuse ” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap an[...]

Studies indicate that these additives can cause your vehicle ’ s emission control system to deteriorate more rapidly . In Canada, premium grade fuel generally contains more metallic additives than regular fuel. W e recommend using regular grade fuel. In Canada, many fuels contain metallic additives, but fuels free of such additives may be availab[...]

Cleaner air Mazda endorses the use of reformulated “ cleaner -burning ” gasolines to improve air quality . Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, t[...]

W ARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. W ARNING: If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may[...]

vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will re[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8 – 10 miles (12 – 16 km) of driving. • Driving on fla[...]

W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power , could [...]

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. CHECKING AND ADDING POWER STEERING FLUID Check the power steering[...]

BRAKE/CLUTCH (IF EQUIPPED) FLUID RESERVOIR Brake and clutch systems are supplied from the same reservoir . The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “ MIN ” and “ MAX ” lines are within the normal operating range, there is no need to add fluid. If the[...]

6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the crosshatch zone for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 10 ° C (50 °[...]

If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result i[...]

W ARNING: Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. If taken internally , drink water and induce vomiting. Seek medical attention immediately . AIR FILTER MAINTENANCE Refer to the service maintenance section for the appropriate intervals for c[...]

6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 7. Replace the air filter housing cover and secure the clamps. 8. Replace the air inlet tube and secure the clamp. Note: [...]

Fluid Classification Application Capacity T ransmission fluid 1 API service GL-4, SAE 75W -90 Manual transaxle (2WD) 2.3L (2.4 quarts) 2 Manual transaxle (4WD) 2.4L (2.5 quarts) 2 MERCON 威 A TF 2.3L / 3.0L engine with Automatic transaxle and oil cooler 9.6L (10.2 quarts) 3 T ransfer Case API service GL-5, SAE 75W -140 Synthetic Lubricant 4WD (Aut[...]

1 Ensure the correct automatic transmission fluid is used. T ransmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCON 威 and MERCON 威 V are not interchangeable. DO NOT mix MERCON 威 and MERCON 威 V . Refer to your scheduled maintenance section to determine the correct service interval. 2 Service refill cap[...]

V EHICLE DIMENSIONS Dimensions 4 Door - inches (mm) (1) V ehicle height w/o roof rack / with roof rack 67.7 (1,720)/70.0 (1,779) (2) Front track / rear 61.3 (1,557)/60.9 (1,548) (3)Overall width (body) 72.0 (1,828) (4) Wheelbase 103.2 (2,621) (5)Overall length w/o trailer hitch / with trailer hitch 174.4 (4,429)/174.7 (4,438) 3 2 1 REVIEW COPY 2005[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification label is located on the structure by the trailing edge of the driver ’ s door or the edge of the drive[...]

V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) Engine number The engine number (the last eight numbers of the vehicle identification number) is stampe[...]

CELL PHONES Use of cell phones and other devices by driver: W ARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver ’ s hands. Use of these devices will[...]

A ABS (see Brakes) .....................163 Accessory delay .......................... 49 Air bag supplemental restraint system .................... 93 – 94, 101, 104 and child safety seats .............. 95 description ................94, 101, 104 disposal ............................ 101, 107 driver air bag ............96, 102, 105 indicator li[...]

wheels ...................................... 211 wiper blades ............................ 213 Climate control (see Air conditioning or Heating) ............31 Clock adjust 6-CD in dash ............................. 26 AM/FM/CD ................................. 22 Clutch fluid .................................. 249, 251 operation while driving ...[...]

comparisons with EP A fuel economy estimates ................. 246 detergent in fuel ..................... 242 filling your vehicle with fuel ........................... 238, 242 – 243 filter , specifications ................ 243 fuel filler door release .............. 54 improving fuel economy ........ 243 octane rating ...................241, 2[...]

daytime running light ...............33 fog lamps ................................... 33 headlamps ................................. 33 headlamps, flash to pass .......... 34 instrument panel, dimming ..... 35 interior lamps ..................... 37 – 38 replacing bulbs ............. 38, 40 – 42 Lane change indicator (see T urn signal) ........[...]

Safety belts (see Safety restraints) ........................ 78, 81 – 86 Safety Canopy ........................... 102 Safety defects, reporting .......... 209 Safety restraints .............. 78, 81 – 86 belt minder ............................... 88 extension assembly .................. 87 for adults ............................. 82 – 85 f[...]

V ehicle Identification Number (VIN) .......................................... 258 V ehicle loading .......................... 145 V entilating your vehicle ........... 162 W W arning lights (see Lights) ....... 14 W asher fluid ..............................226 W ater , Driving through ............. 182 W indows power ............................[...]

266[...]

267[...]

268[...]

269[...]

270[...]

271[...]

272[...]