Makita EW200TR manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Makita EW200TR, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Makita EW200TR one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Makita EW200TR. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Makita EW200TR should contain:
- informations concerning technical data of Makita EW200TR
- name of the manufacturer and a year of construction of the Makita EW200TR item
- rules of operation, control and maintenance of the Makita EW200TR item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Makita EW200TR alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Makita EW200TR, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Makita service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Makita EW200TR.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Makita EW200TR item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    PUMP EW2OOTR MODEL EW3OOTR EW400TR INSTRUCTION MANUAL I ISSUEEMD-PU0835 I piEGKq[...]

  • Page 2

    [...]

  • Page 3

    FOREWORD Thank you for purchasing a Makita trash pump. This manual covers operation and maintenance of trash pumps. All information in this publication is based on the latest product infor- mation available at the time of approval for printing. Please read this manual carefully before operating. CONTENTS Page 1. PUMP SAFETY 1 2. COMPONENTS 2 3. PRE[...]

  • Page 4

    ID PUMP SAFETY Please make sure you review each precaution carefully. SURROUNDINGS H Operate the pump on a stable, level surface free of small rocks, loose gravel, etc. H Keep pump at least 3 feet (1 meter) away from buildings. H Keep pump away from flammables and other hazardous materials (trash, rags, lubricants, explosives). FIRE PREVENTION m Be[...]

  • Page 5

    Spark plug Fuel cock Speed control lever Fuel tank Plug(priming) Pump strainer Drain plug (at two places) -2-[...]

  • Page 6

    3. PREPARATIONS FOR STARTING 1. Connect the suction hose. Use a reinforced-wall or wire braided hose to prevent suction collapse. Since the pump’s self-priming time is directly proportional to hose length, a short hose is recommended. tion hose. Gravel or debris sucked into the pump will cause serious 2. Connect the discharge hose. When using a f[...]

  • Page 7

    4. Check the fuel level. If level is low, fill to the shoulder of the fuel filter. Use fresh, clean automotive gasoline. 5. Check the priming water. It is recommended that the water chamber of pump casing should be primed with full of water before operating. ICAUTION], . Never attempt to operate the pump without priming water or the pump will overh[...]

  • Page 8

    4. STARTING THE ENGINE 1. Open the fuel cock. 2. Set the speed control lever to “START.” -. .. . . . EW400TR 3. Close the choke. m If the engine is warm or the ambient temperature is high, close the choke half-way, or keep it open fully. If the engine is cold, or the ambient temperature is low, close the choke. . -5- Choke knob -I EW400TR I[...]

  • Page 9

    4. Pull the starter handle slowly until re- sistance is felt. This is the "compression" point. Return the handle to its original position and pull swiftly. Do not pull out the rope all the way. I After starting the engine, allow the starter handle return to its original position while still holding the handle. -6-[...]

  • Page 10

    5. OPERATION 1. After starting the engine, gradually open choke by turning the choke lever and finally keep it open fully. H Do not fully open the choke immediately when the engine is cold or the ambient temperature is low, because the engine may stop. 2. After the engine starts, set the speed control lever at the low speed position (L) and warm it[...]

  • Page 11

    6. STOPPING THE ENGINE 1. Set the speed control lever to the low speed position and allow the engine to run at low speed for 2 or 3 minutes before stopping. 2. Keep depressing the STOP BUTON until the engine stops. Do not stop the engine suddenly when it is running at high speed. 3. Close the fuel cock. 4. Pull the starter handle slowly and return [...]

  • Page 12

    DAILY INSPECTION Before running the pump, check the following service items: Enough fuel. m Excessive vibration, noise. Clean air cleaner element. Safe surroundings. Enough clean engine oil. D Leakage of gasoline and engine oil. Loose or broken bolts and nuts. Check the priming water. 8 hours (daily) PERIODIC INSPECTION Periodic maintenance is vita[...]

  • Page 13

    a. "HOW TOWAINTENANCE INSPECTING THE SPARK PLUG w Clean off carbon deposits on the plug electrode using a plug cleaner or wire brush. Check electrode gap. Adjust it to between 0.02 and 0.03 inches. (0.6 and 0.7") ENGINE OIL CHANGE Initial oil change ...... 20 hours of operation Thereafter.. .Every 50 hours of operation :CAUTION]- Make sur[...]

  • Page 14

    SERVICING THE AIR CLEANER Maintaining an air cleaner in proper condition is very important. Dirt induced through im- properly installed, improperly serviced or in- adequate elements, wears out engines. Keep the element always clean. (a) Unlock the cover and remove the cleaner element. (b) Inner element:Wash the element with kerosene, then soak it i[...]

  • Page 15

    Pump does not run. I Pumping volume is small. Pump does not self-prime. 7 c Engine does not start. (See page 13.) Sticking of impeller (Disassemble and clean.) Sucking air at suction side (Check piping at suction side.) Drop in engine output (Consult your nearest dealer.) Breakage of mechanical seal (Consult your nearest dealer.) High suction lift [...]

  • Page 16

    fore you take the pump to your Makita dealer. If you still have trouble after com- pleting the checks, take the pump to your nearest Makita dealer. 1. Remove the plug and connect it to the plug cap. Pull the starter handle while putting the plug against the engine ground. 2. Try with a new plug if the spark is weak or no spark flies. 3. The ignitio[...]

  • Page 17

    10. PREPARATIONS FOR STORAGE ~~~ ~ I Drain all water from the drain plug. , I When retightening drain plug, be sure to clean the drain plug and the thread of casincl. Otherwise, the [CAUTION 1u thread may be da6aged. II J 1 Remove the strainer cup, and open the strainer cock to discharge the fuel from the fuel tank. Remove the carburetor float cham[...]

  • Page 18

    11 OIL SENSOR INSTRUCTIONS OIL SENSOR (OPTION) (a) The oil sensor detects the fall in oil level in the crankcase and automatically stops the engine when the oil level falls down below the predetermined level. (b) When engine has stopped automatically, check the oil level. Refill engine oil to the upper level and restart the engine. (c) If the engin[...]

  • Page 19

    [...]

  • Page 20

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period. retum the COMPLETE tool, freight[...]