Lenovo 9648 manual

Us er Gu i d e T ypes 6490, 8700, 8701, 8705 T ypes 8717, 8973, 8975, 8979 T ypes 8983, 8985, 8991, 8995 T ypes 9265, 9269, 9277, 9279 T ypes 9283, 9287, 9379, 9383 T ypes 9387, 9389, 9631, 9635 T ypes 9637, 9646, 9648, 9694[...]

[...]

Us er Gu i d e[...]

Note Before using this information and the pr oduct it supports, be sure to read the“Important safety information” on page v and Appendix B, “Notices,” on page 71. Fourth Edition (February 2007) © Copyright Lenovo 2006, 2007. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. U.S. GOVERNMENT USERS [...]

Contents Important safety information . . . . . .v Conditions that requir e immediate action . . . . .v General safety guidelines . . . . . . . . . .v i Service and upgrades . . . . . . . . . .v i Static electricity prevention . . . . . . . . vii Power cords and power adapters . . . . . . vii V oltage-selection switch . . . . . . . . . viii Extensi[...]

Chapter 7. T roubleshooting and diagnostics . . . . . . . . . . . . .5 3 Basic troubleshooting . . . . . . . . . . .5 3 Diagnostic programs . . . . . . . . . . .5 4 PC-Doctor for W indows . . . . . . . . .5 5 PC-Doctor for DOS . . . . . . . . . . .5 5 PC-Doctor for W indows PE . . . . . . . .5 7 Cleaning the mouse . . . . . . . . . . .5 7 Optical m[...]

Important safety information Note Please read important safety information first. This information can help you safely use your desktop or notebook personal computer . Follow and r etain all information included with your computer . The information in this document does not alter the terms of your purchase agr eement or the Lenovo ™ Limited W arr[...]

In the unlikely event that you notice any of the following conditions, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance. See Chapter 8, “Getting information, help, and service,” on p[...]

Danger Hazardous moving parts. Keep fingers and other body parts away . Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover . Static electricity prevention Static electricity , although harmless to you, can seriously damage computer components and options. Impro[...]

The power cords shall be safety appr oved. For Germany , it shall be H05VV -F , 3G, 0.75 mm 2 , or better . For other countries, the suitable types shall be used accordingly . Never wrap a power cord ar ound a power adapter or other object. Doing so can stress the cor d in ways that can cause the cord to fray , crack, or crimp. This can present a s[...]

Extension cords and related devices Ensure that extension cor ds, surge pr otectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical r equirements of the product. Never overload these devices. If power strips ar e used, the load should not exceed the power strip input rating. Consult an electrician f[...]

Never attempt to open or service any battery . Do not crush, puncture, or incinerate batteries or short circuit the metal contacts. Do not expose the battery to water or other liquids. Only rechar ge the battery pack strictly according to instructions included in the product documentation. Battery abuse or mishandling can cause the battery to overh[...]

v Do not use non-desktop air filtration devices. Operating environment The optimal environment in which to use your computer is 10°C-35°C (50°F-95°F) with humidity ranging between 35% and 80%. If your computer is stored or transported in temperatures less than 10°C (50°F), allow the cold computer to rise slowly to an optimal operating tempera[...]

To connect: 1. T urn everything OFF . 2. First, attach all cables to devices. 3. Attach signal cables to connectors. 4. Attach power cords to outlet. 5. T urn device ON. To disconnect: 1. T urn everything OFF . 2. First, remove power cords fr om outlet. 3. Remove signal cables from connectors. 4. Remove all cables from devices. Lithium battery noti[...]

Laser compliance statement Some personal computer models are equipped fr om the factory with a CD or DVD drive. CD and DVD drives are also sold separately as options. CD and DVD drives are laser pr oducts. These drives are certified in the U.S. to conform to the requir ements of the Department of Health and Human Services 21 Code of Federal Regulat[...]

Note to CA TV system installer This reminder is pr ovided to call the CA TV system installer's attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for pr oper grounding and, in particular , specifies that the cable ground shall be connected to the grounding system of the building, as close as possible to [...]

The following notice applies to all countries and regions: Danger Outdoor antenna grounding If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded as to provide some protection against voltage surges and built-up static charges. Lightning For added protection for this equipment during a [...]

complies with EN 50332-2 Sub clause 5.1. This specification limits the computer ’s maximum wide band true RMS output voltage to 150mV . To help pr otect against hearing loss, ensure that the headphones or earphones you use also comply with EN 50332-2 (Sub clause 6.1) for a wide band characteristic voltage of 75mV . Using headphones that do not co[...]

Introduction This User Guide contains the following information: v Chapter 1, “Arranging your workspace,” on page 1 pr ovides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets. v Chapter 2, “Setting up your computer,” on page 3 pr ovides information about setting [...]

xviii User Guide[...]

Chapter 1. Arranging your workspace To get the most from your computer , arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Y our comfort is of foremost importance, but light sour ces, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace. Comfor[...]

Glare and lighting Position the monitor to minimize glare and r eflections from over head lights, windows, and other light sources. Even r eflected light from shiny surfaces can cause annoying reflections on your monitor scr een. Place the monitor at right angles to windows and other light sources, when possible. Reduce over head lighting, if neces[...]

Chapter 2. Setting up your computer Before you begin, make sur e you set up your computer in the best possible work area that suits your needs and the kind of work you do. For mor e information, refer to Chapter 1, “Arranging your workspace,” on page 1. Note: Read “Important safety information” on page v“Important safety information” on[...]

If your computer does not have a voltage selection switch, it is designed to operate only at the voltage provided in the country or r egion where it was originally purchased. Continue with step 2. 2. Y our keyboard cable might have a standard keyboar d connector 1 or a Universal Serial Bus (USB) connector 2 . Connect the keyboard cable [...]

v If you have a digital video interface (DVI) monitor , connect the cable to the connector as shown. Note: Y our computer must have an adapter installed that supports the DVI monitor . 5. If you have a modem, connect the modem using the following information. L IN E PHONE P H O N E LINE PHONE LINE PHONE LINE 1 This illustration shows the two [...]

6. If you have audio devices, attach them using the following instructions. For more information about speakers, see steps 7 and 8 on page 7. 1 Audio line-in This connector receives audio signals fr om an external audio device, such as a stereo system. 2 Audio line-out This connector sends audio signals from the computer to external dev[...]

8. If you have unpower ed speakers with no ac adapter , use the following instructions. a. Connect the cable that runs between the speakers, if necessary . On some speakers, this cable is permanently attached. b. Connect the speakers to the computer . 9. Connect any additional devices that you have. Y our computer might not have all connectors that[...]

10. Connect the power cor ds to properly gr ounded electrical outlets. Note: Refer to the Access Help online help system for more information about connectors. See “Access Help” on page 60 for instructions on how to open the online help system. T urning on power T urn on the monitor and other external devices first, and then turn on the compute[...]

Completing important tasks After you have set up your computer , perform the following tasks, which will save you time and trouble later: v Cr eate a diagnostic CD image, diagnostic diskettes, or rescue media. Diagnostic programs ar e used to test hardwar e components of your computer and report operating-system-controlled settings that can cause h[...]

10 User Guide[...]

Chapter 3. Installing options This chapter provides an intr oduction to the features and options that ar e available for your computer . Yo u can expand the capabilities of your computer by adding memory , adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option. Note: Use only par[...]

v Intel Pentium 4 pr ocessor v Intel Celer on ® D processor v AMD Athlon 64 v AMD Sempr on v Internal cache (size varies by model type) Memory v Support for two double data rate 2 (DDR2) dual inline memory modules (DIMMs) v 512 KB flash memory for system pr ograms Internal drives v 3.5-inch, slim, 1.44 MB diskette drive v Serial Advanced T echnolo[...]

v VGA monitor connector v Audio connectors (see Audio subsystem) Expansion v Four drive bays v Tw o standard PCI adapter connectors v One PCI Expr ess x1 adapter connector v One PCI Expr ess x16 graphics adapter connector (some models) Power v 250 W att power supply with manual voltage selection switch (some models) v 280 W att power supply with ma[...]

Specifications This section lists the physical specifications for your computer . Dimensions Height: 400 mm (15.7 in.) W idth: 175 mm (6.9 in.) Depth: 432 mm (17.0 in.) W eight Minimum configuration: 8.17 kg (18 lb) Maximum configuration: 10.21 kg (22.5 lb) Environment Air temperatur e: System on: 10° to 35°C (50° to 95° F) System off: 10° to [...]

A vailable options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system – USB devices, such as printers, joysticks, and scanners – Security[...]

Handling static-sensitive devices Static electricity , although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instr ucted to do so. When you handle options and other computer components, take these precautions to avoid stat[...]

Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer . 1 USB connector 3 Microphone connector 2 Headphone connector 4 USB connector Chapter 3. Installing options 17[...]

Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer . 1 Power supply diagnostic LEDs 10 Ethernet connector 2 V oltage selection switch (some models) 11 USB connectors (2) 3 Power connector 12 Microphone connector 4[...]

Connector Description Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector . Keyboard connector Used to attach a keyboar d that uses a standard keyboar d connector . Serial connector Used to attach an external modem, serial printer , or other devices that use a 9-pin serial connector . Par[...]

Removing the cover Important Read “Important safety information” on page v“Important safety information” on page v and “Handling static-sensitive devices” on page 16 before r emoving the computer cover . To remove the computer cover: 1. Remove any media (diskettes, CDs, or tapes) fr om the drives, shut down your operating system, and tu[...]

Locating components The following illustration will help you locate the various components in your computer . 1 Micropr ocessor fan and heat sink 4 PCI Express and PCI adapter connectors 2 Memory modules 5 System fan 3 PCI adapter card 6 Power supply Chapter 3. Installing options 21[...]

Identifying parts on the system board The system board (sometimes called the planar or motherboard ) is the main cir cuit board in your computer . It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later . The following illustration shows the locations of parts on the system boa[...]

The following illustration shows the locations of parts on the system board (some models). 1 Micropr ocessor and heat sink 12 Front USB connectors (2) 2 Micropr ocessor fan connector 13 Serial (COM) connector 3 Memory connector 1 14 Front audio connector 4 Memory connector 2 15 CD-IN connector 5[...]

The following illustration shows the locations of parts on the system board (some models). 1 Micropr ocessor and heat sink 12 Front panel connector 2 Micropr ocessor fan connector 13 Front panel USB connectors (2) 3 Memory connector 1 14 Front audio connector 4 Memory connector 2 15 CD-IN connector ?[...]

Installing memory Y our computer has two connectors for installing dual inline memory modules (DIMMs) that provide up to a maximum of 4.0 GB of system memory . When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin double data rate 2 synchr onous dynamic random access memory (DDR2 SDRAM). v Use 256 MB, 512 MB, 1.0 GB, or 2.[...]

Installing adapters This section provides information and instr uctions for installing and removing adapters. Y our computer has two expansion connectors for PCI adapters and one for a PCI Express x1 adapter . To install an adapter: 1. Remove the computer cover . See “Removing the cover” on page 20. 2. At the r ear of the computer , press the r[...]

5. Pivot the adapter latch to the closed position to secur e the adapters. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 37. Chapter 3. Installing options 27[...]

Installing internal drives This section provides information and instr uctions for installing and removing internal drives. Internal drives are devices that your computer uses to r ead and store data. Yo u can add drives to your computer to increase storage capacity and to enable your computer to read other types of media. Some of the dif ferent dr[...]

The following illustration shows the locations of the drive bays. The following list describes the types and size of drives you can install in each bay: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) v Optical drive such as CD drive or DVD drive (preinstalled in some models) v 5.25-inch hard disk drive v 3.5-inch hard disk drive (requir es a Uni[...]

Installing a drive in bay 1 or bay 2 To install a drive in bay 1 or bay 2, follow these steps: 1. Remove the computer cover . See “Removing the cover” on page 20. 2. Remove the fr ont bezel by releasing the thr ee plastic tabs on the left side and pivoting the bezel outward. Car efully set the bezel to the side without disconnecting the power s[...]

7. For a 5.25-inch drive, install a r etainer bracket on the side of the drive. 8. For a 3.5-inch drive, you must use a Universal Adapter Bracket, 5.25 to 3.5-inch. Yo u can obtain a Universal Adapter Bracket, 5.25 to 3.5-inch from a local computer retailer or by contacting the Customer Support Center . Install a retainer bracket on the side of the[...]

Connecting drives The steps to connect a drive are dif ferent depending on the type of drive. Use one of the following procedur es for your drive connection. Connecting the first optical drive 1. The drive r equires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board. 2. Locate the thr ee[...]

Connecting a serial ATA hard disk drive A serial hard disk drive can be connected to any available S ATA connector . 1. Locate the signal cable that comes with the new drive. 2. Locate an available S ATA connector on the system board. See “Identifying parts on the system board” on page 22. 3. Connect one end of the signal cable to the drive and[...]

Integrated cable lock W ith an integrated cable lock (sometimes referred to as the Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixtur e. The cable lock attaches to a security slot at the rear of your computer and is operated with a key . The cable lock also locks the buttons used to open the computer cove[...]

Padlock Y our computer is equipped with a padlock loop such that the cover cannot be removed when a padlock is installed. Password protection To deter unauthorized use of your computer , you can use the Setup Utility program to set passwor ds. See “Using passwords” on page 47. What to do next v To work with another option, go to the appropriate[...]

To change the battery: 1. T urn off the computer and all attached devices. 2. Remove the computer cover . See “Removing the cover” on page 20. 3. Locate the battery . See “Identifying parts on the system board” on page 22. 4. Remove the old battery . 5. Install the new battery . 6. Replace the computer cover , and plug in the power cor d. S[...]

8. Move the jumper back to the standar d (pins 1 and 2). 9. Replace the computer cover and connect the power cor d. See “Replacing the cover and connecting the cables.” Replacing the cover and connecting the cables After working with options, you need to install any removed parts, r eplace the computer cover , and r econnect any cables, includi[...]

38 User Guide[...]

Chapter 4. Recovering software There ar e a variety of methods to choose from when considering how to r ecover software in the event of a softwar e or hardwar e-related pr oblem. Some methods vary depending on the type of operating system you have. This chapter will help you become familiar with recovery solutions pr ovided by Lenovo. This chapter [...]

v W indows V ista: Use Product Recovery discs to restor e your computer to the original factory contents only . When using Product Recovery discs on W indows XP , you are given the option to enter the Rescue and Recovery workspace and choose from a variety of r ecovery operations. When using Product Recovery discs on W indows V ista, you are prompt[...]

v On a pr otected area of your har d disk v On a second har d disk installed in your computer v On an externally attached USB har d disk v On a network drive v On r ecordable CDs or DVDs (a r ecordable CD or DVD drive is r equired for this option) After you have backed up your hard disk, you can r estore the complete contents of the hard disk, r es[...]

multiple partitions on your hard disk, you have the option to r estore the factory contents to the C: partition and leave the other partitions intact. Because the Rescue and Recovery workspace operates independently from the W indows operating system, you can restor e the factory contents even if you cannot start the W indows operating system. Atte[...]

To create rescue media, do the following: 1. Open the Start menu fr om the W indows desktop, select All Programs , click ThinkV antage , then click Create Recovery Media . 2. In the Rescue Media ar ea, select the type of rescue media you want to cr eate. Yo u can create rescue media using a CD, USB har d drive, or a second internal hard disk drive.[...]

2. Insert the Recovery Repair diskette into diskette drive A. 3. T urn on the computer and follow the instructions on the screen. Note: If the repair operation finishes without error , you will be able to access the Rescue and Recovery workspace by repeatedly pr essing the F1 1 key while you restart your computer . When you hear beeps or see a logo[...]

Setting a rescue device in the startup sequence Before you start the Rescue and Recovery pr ogram from a CD, DVD, USB har d disk drive, or any external device, you must first change the startup sequence in the Setup Utility . To view or change the startup sequence, do the following: 1. W ith the computer off, r epeatedly press and r elease the F1 k[...]

46 User Guide[...]

Chapter 5. Using the Setup Utility The Setup Utility program is stor ed in the electrically erasable programmable read-only memory (EEPROM) of your computer . The Setup Utility program is used to view and change the configuration settings of your computer , regar dless of which operating system you are using. However , the operating-system settings[...]

v Have at least eight characters in length v Contain at least one alphabetic character , one numeric character , and one symbol v Contain at least one of the following symbols: , . / ` ; ' [] v Yo u can also use the space bar v Setup Utility pr ogram and hard disk drive passwor ds are not case sensitive v Not be your name or your user name v N[...]

To set Security Profile by Device, do the following: 1. Start the Setup Utility pr ogram (see “Starting the Setup Utility program” on page 47). 2. Fr om the Setup Utility program menu, select Security . 3. Select Security Profile by Device . 4. Select the desir ed devices and settings and press Enter . 5. Return to the Setup Utility pr ogram me[...]

Advanced settings On some computer models the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This featur e works only with HyperThreading-awar e operating systems, such as Microsoft W indows XP . The default setting for HyperThreading is Enabled. However , if you select Set Defaults and are using an operating system oth[...]

Chapter 6. Updating system programs This chapter contains information about updating POST/BIOS and how to recover from a POST/BIOS update failur e. Using system programs System programs ar e the basic layer of software that is built into your computer . They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the S[...]

52 User Guide[...]

Chapter 7. T roubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic pr ograms. If your computer problem is not described her e, see Chapter 8, “Getting information, help, and service,” on page 59 for additional troubleshooting r esources. Basic troubleshooting The following table provides information to [...]

Symptom Action The Enhanced Performance USB Keyboard does not work. V erify that: v The computer is turned on. v The keyboard is securely connected to a USB connector on the fr ont or rear of the computer . v No keys are stuck. If you cannot correct the pr oblem, have the computer serviced. Refer to the safety and warranty information that is provi[...]

created by both diagnostic pr ograms. Yo u will need the log files when you speak to a Lenovo technical support repr esentative. (The log file created by PC-Doctor for W indows is automatically saved in C:PCDRDET AILED.TXT .) PC-Doctor for Windows PC-Doctor for W indows is a diagnostic program that works through the W indows operating system. The[...]

3. Repeatedly pr ess and release the F1 1 key as you turn on the computer . 4. When you hear beeps or see a logo scr een, stop pressing the F1 1 key . The Rescue and Recovery workspace opens. Note: For some models, press the Esc key to enter Rescue and Recovery . 5. Fr om the Rescue and Recovery workspace, select Create diagnostic disks . 6. Follow[...]

PC-Doctor for Windows PE Depending upon your machine type and model, you either have PC-Doctor for DOS or PC-Doctor for W indows PE on your Lenovo computer . The PC-Doctor for W indows PE diagnostic program is part of the Rescue and Recovery workspace. Use PC-Doctor for W indows PE, if you are unable to start the W indows operating system or if PC-[...]

Note: The following illustration might be slightly different fr om your mouse. 1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage To clean a mouse with a ball, follow the instructions below: 1. T urn off your computer . 2. Disconnect the mouse cable fr om the computer . 3. T urn the mouse upside down. T wist the retainer r[...]

Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactur ed by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful r esources r elating t[...]

v Client Security Solution v Factory Recovery v System updates v Service and support Note: ThinkV antage T echnologies are only available on select Lenovo computers. To access the ThinkV antage Pr oductivity Center program, open the Start menu from the W indows desktop, select All Programs , select ThinkV antage , and click Productivity Center . Ac[...]

Using the documentation and diagnostic programs Many computer problems can be solved without outside assistance. If you experience a problem with your computer , see Chapter 7, “T roubleshooting and diagnostics,” on page 53. For information on additional resour ces to help you troubleshoot your computer pr oblem, see “Information resour ces?[...]

For a list of service and support phone numbers for your country or region, go to http://www .lenovo.com/support/ and click Support phone list or refer to the safety and warranty information provided with your computer . Note: Phone numbers are subject to change without notice. If the number for your country or region is not pr ovided, contact your[...]

Appendix A. Manual modem commands This appendix provides commands for manually pr ogramming your modem. Commands are accepted by the modem while it is in Command Mode. Y our modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your modem from a PC running communication software or any ot[...]

Command Function H1 Force modem of f-hook (make busy) Note: H1 command is not supported for Italy I_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firmware ID I4 Reserved ID L_ L0 Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M_ M0 Internal speaker off M1 In[...]

Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 T urn on CD when remote carrier is present &D_ &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle [...]

Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active pr ofile as Profile 0 &W1 Stores the active pr ofile as Profile 1 %E_ %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Selec[...]

Fax Class 1 commands +F AE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n T ransmit data with HDLC framing +FTM=n T ransmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. +F AA=n Adaptive answer . +F AXERR Fax error value. [...]

+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID. V oice commands #BDR Select Baud Rate #CID Enable Caller ID detection and reporting format #CLS Select Data, Fax or V oice/Audio #MDL? Identify M[...]

Attention Switzerland User: If your Swisscom phone line does not have T axsignal switched OFF , modem function may be impaired. The impairment may be r esolved by a filter with the following specifications: T elekom PTT SCR-BE T aximpulssperrfilter-12kHz PTT Art. 444.1 12.7 Bakom 93.0291.Z.N Appendix A. Manual modem commands 69[...]

70 User Guide[...]

Appendix B. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area. Any refer ence to a Lenovo product, pr ogram, or service is not intended to state or imply that only that[...]

vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation. Actual r esults may vary . Users of this document should verify the applicable data [...]

Index A Access Help 60 adapters connectors 26 installing 26 peripheral component interconnect (PCI) 15 antivirus software, updating 9 arranging your workspace 1 audio line in connector 19 audio line out connector 19 audio, subsystem 12 B battery location 22 BIOS, updating (flashing) 51 C cables, connecting 37 changing startup device sequence 49 cha[...]

modem commands (continued) Extended AT 65 Fax Class 1 67 Fax Class 2 67 MNP/V .42/V .42bis/V .44 66 V oice 68 mouse connector 19 mouse, cleaning non-optical 57 optical mouse 57 N non-optical mouse 57 notices 71 O obtaining device drivers 20 Online Books folder 59 operating system installing 9 updating 9 optical mouse 57 options 15 available 14 exte[...]

[...]

Part Number: 41X5664 Printed in USA (1P) P/N: 41X5664[...]