English dropdown-ico

Kenmore 625.3847 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Kenmore 625.3847, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Kenmore 625.3847 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Kenmore 625.3847. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Kenmore 625.3847 should contain:
- informations concerning technical data of Kenmore 625.3847
- name of the manufacturer and a year of construction of the Kenmore 625.3847 item
- rules of operation, control and maintenance of the Kenmore 625.3847 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Kenmore 625.3847 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Kenmore 625.3847, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Kenmore service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Kenmore 625.3847.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Kenmore 625.3847 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    OWNER'S MANUAL MODEL NO. 625.384700 Caution: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product. If you have questions when installing, operating or maintaining your reverse osmosis system, call this toll-free number... 1-800-426-9345 SAVE THIS MANUAL PRINTED IN U.S.A. Reverse Osmosis Drinking Water Sy[...]

  • Page 2

    - WARRANTY- 1 li I I /liJ I Ill li I I _ I Ill I / I lill_ I FULL WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM = = (except filter cartridges and R. O. membrane) = I For one year from the date of purchase, when the Reverse Osmosis Drinking Water System is installed I and maintained in accordance with our instructions, Sears will repair, free of[...]

  • Page 3

    - TABLE OF CONTENTS - Where To Install the RO System ........ 4 Tools and Materials Needed ........... 4 Installation Steps .................... 5- 9 Cold Water Supply .................. 5 Drain Adapter ..................... 6 Faucet ............................ 6- 7 RO Assembly ...................... 7 Storage Tank, Tubing Connections .... 8 Insta[...]

  • Page 4

    - WHERE TO INSTALL THE RO SYSTEM - The RO assembly and storage tank is designed for installation under the sink, usually in the kitchen or bathroom. The RO assembly mounts on a wall sur- face, or can lay on the cabinet floor next to the storage tank. Hanger washers and wood screws are included for cabinet wall mounting. The RO product water faucet [...]

  • Page 5

    - STEP 1: INSTALL COLD WATER SUPPLY FITTING - Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak- tight connection to the RO 1/4" tubing (see FIG. 8, page 8). A typical connection using the included water supply fitting is shown in FIG.3 - A below. An optiona[...]

  • Page 6

    - STEP 2: INSTALL DRAIN ADAPTER - • Note: Running the drain tubing directly to a floor drain, sump, standpipe, laundry tub, etc., as shown on page 18, is preferred. However, if that is not pos- sible or practical, the included drain adapter installs in the sink drain pipe, always above or ahead of the p-trap (FIG. 4). Be sure to comply with your [...]

  • Page 7

    - STEP 3: INSTALL FAUCET (cont.)- B. ASSEMBLE FAUCET 1. If not already assembled, install the rubber washer, spacer, flat (or lock) washer and hex nut onto the threaded faucet stud. 2. Apply Teflon tape to the end of the faucet stud. Turn the tubing adapter with a blue collet onto the stud and hand tighten, then wrench 1/4 turn only. BE CAREFUL NOT[...]

  • Page 8

    - STEP 5: INSTALL STORAGE TANK, MAKE REMAINING TUBING CONNECTIONS - 1. CONNECT DRAIN TUBING, FAUCET TO DRAIN ADAPTER: Referring to FIG. 8, run the loose section (connected to faucet barb fitting) of black 3 / 8" tubing from the faucet to the drain adapter, with a black collet, installed on page 6. Cut this tubing as needed to route in as strai[...]

  • Page 9

    - STEP 6: SANITIZING, PRESSURE TESTING & PURGING - SANITIZING Sanitizing is recommended upon installation of the RO system, and after servicing inner parts. It is im- portant for the service person to have clean hands while handling inner parts of the system. CAUTION: Be sure to remove the RO membrane and both filter cartridges as follows, befo[...]

  • Page 10

    - HOW YOUR REVERSE OSMOSIS SYSTEM WORKS - PREFILTER Water from the cold supply pipe enters the RO as- sembly prefilter first (FIG. 8 and schematic below). The prefilter has a replaceable sediment cartridge with activated carbon in its composition. The car- tridge (10 micron) removes sand, silt, dirt, other sedi- ments, and up to the ppm of chlorine[...]

  • Page 11

    - CARE OF YOUR REVERSE OSMOSIS SYSTEM - To keep your reverse osmosis system operating and producing high quality water, you must make sure supply water is always within the limits shown in the specifications. Good supply water helps to assure longer life from the RO membrane cartridge, prefilter and postfilter cartridges. However, each of these wil[...]

  • Page 12

    - CARE OF YOUR REVERSE OSMOSIS SYSTEM - 2. Press inward while turning the RO cap to the left (_) to remove from the bracket/membrane housing. 3. Use a pliers, or heavy wire made into a hook, to pull the RO cartridge from the housing. Note: Sanitizing is recommended after servicing in- ner parts of the system (see page 9). 4. Install the new cartrid[...]

  • Page 13

    - CARE OF YOUR REVERSE OSMOSIS SYSTEM - TUBING CONNECTION (continued) If tubing other than tubing supplied with the system is used, be sure it is of high quality, exact size and roundness with a smooth surface. AUTOMATIC SHUTOFF SERVICE If the shutoff assembly requires service, be sure to reassemble parts exactly as shown in FIG. 12, and to reconne[...]

  • Page 14

    - CARE OF YOUR REVERSE OSMOSIS SYSTEM - REVERSE OSMOSIS SYSTEM CARE GUIDE MODEL NO. 625.384700 1. AT LEAST every 6 months, replace the prefilter and postfilter cartridges. Clean or replace the flow control and screen. 2. Replace the RO membrane cartridge when the percent rejection of total dissolved solids (TDS) is less than shown in the specificat[...]

  • Page 15

    - DIMENSIONS and SPECIFICATIONS - 15" Supply water pressure limits ........................ 40 - 125 psi Supply water temperature limits ..................... 40 - 100 °F Maximum total dissolved solids (TDS) ............... 2000 ppm Maximum water hardness @ 6.9 pH ................. 10 gpg Maximum iron, manganese, hydrogen sulfide ......... 0 [...]

  • Page 16

    - REPAIR PARTS - Kenmore Reverse Osmosis Drinking Water System, Model No, 625.384700 33 !DRA , t ADAPTER 34 ! Bracket!Membrane Housing PUSH - IN FITrlNGS ] CO et 24 I 26 1/4" Tubing _ U 35 _10_ _ o-ring seals j3 I" I I 21 20 19 1 I I I I I .I 5 -9 13 12 10 23 16[...]

  • Page 17

    Key NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 - REPAIR PARTS - Kenmore Reverse Osmosis Drinking Water System, Part Number 7205350 7207920 7185788 42-34702 7177175 7174965 7207881 7156535 7170246 42-34370 7156577 7171674 7171682 7112442 7112434 7014979 7099296 7112426 7030721 7133838 7208502 7207899 42-34373 7[...]

  • Page 18

    - REMOTE LOCATION FOR REVERSE OSMOSIS SYSTEM - REMOTE RO INSTALLATION (storage tank not shown) Possible remote locations for the RO nearby the kitchen or bathroom sink include; (1) a basement area underneath the sink, and (2) an adjacent room or closet. Longer lengths of tubing may be needed (see parts list on page 17). You can run the drain tubing[...]

  • Page 19

    19[...]

  • Page 20

    OWNER'S MANUAL MODEL NO. 625,384700 The model number of your reverse osmosis system is found on the rating decal. This decal is on the top of the bracket. When requesting service or ordering parts, always provide the following in- formation: • Product Type • Model Number Part Number Part Description Reverse Osmosis Drinking Water System Fo[...]