IBM 9117-MMB manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of IBM 9117-MMB, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of IBM 9117-MMB one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of IBM 9117-MMB. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of IBM 9117-MMB should contain:
- informations concerning technical data of IBM 9117-MMB
- name of the manufacturer and a year of construction of the IBM 9117-MMB item
- rules of operation, control and maintenance of the IBM 9117-MMB item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of IBM 9117-MMB alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of IBM 9117-MMB, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the IBM service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of IBM 9117-MMB.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the IBM 9117-MMB item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    P ower Systems P ower supplies for the 9117-MMB or 9179-MHB [...]

  • Page 2

    [...]

  • Page 3

    P ower Systems P ower supplies for the 9117-MMB or 9179-MHB [...]

  • Page 4

    Note Before using this information and the pr oduct it supports, read the information in “Notices” on page 97, “Safety notices” on page v, the IBM Systems Safety Notices manual, G229-9054, and the IBM Environmental Notices and User Guide , Z125–5823. This edition applies to IBM Power Systems servers that contain the POWER7 processor and t[...]

  • Page 5

    Contents Safety notices ................................. v Power supplies for the 91 17-MMB or 9179-MHB ................... 1 What's new in Power supplies ............................. 1 Removing the 91 17-MMB or 9179-MHB power supply with the power turned off ............ 1 Removing the 91 17-MMB or 9179-MHB power supply with the power turne[...]

  • Page 6

    Disconnecting the power cords fr om the 8202-E4B or 8205-E6B system .............. 5 8 Connecting the power cords to the 8202-E4B or 8205-E6B system ................ 6 0 Installing a feature by using the Har dware Management Console ................ 6 0 Installing a part by using the Systems Director Management Console ............... 6 1 V erifyin[...]

  • Page 7

    Safety notices Safety notices may be printed throughout this guide: v DANGER notices call attention to a situation that is potentially lethal or extremely hazar dous to people. v CAUTION notices call attention to a situation that is potentially hazardous to people because of some existing condition. v Attention notices call attention to the possibi[...]

  • Page 8

    DANGER When working on or around the system, observe the following precautions: Electrical voltage and current from power , telephone, and communication cables are hazardous. T o avoid a shock hazard: v Connect power to this unit only with the IBM provided power cord. Do not use the IBM provided power cord for any other product. v Do not open or se[...]

  • Page 9

    Observe the following precautions when working on or around your IT rack system: v Heavy equipment–personal injury or equipment damage might result if mishandled. v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v T o avoid hazardous conditions due to uneven mechanical loading, always[...]

  • Page 10

    CAUTION: Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building: v Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack cabinet. When possible, restore t[...]

  • Page 11

    (L003) or All lasers are certified in the U.S. to conform to the r equirements of DHHS 21 CFR Subchapter J for class 1 laser products. Outside the U.S., they ar e certified to be in compliance with IEC 60825 as a class 1 laser product. Consult the label on each part for laser certification numbers and appr oval information. CAUTION: This product mi[...]

  • Page 12

    CAUTION: Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical fiber cable or open receptacle. (C027) CAUTION: This product contains a Class 1M laser . Do not view directly with optical instruments. [...]

  • Page 13

    Power supplies for the 91 17-MMB or 9179-MHB Learn about removing and r eplacing a power supply in a server . Learn about removing and replacing a power supply , fan, or input power distribution assembly in a 5802 or a 5877 expansion unit. What's new in Power supplies Read about new or changed information in Power supplies since the previous u[...]

  • Page 14

    6. Lift the tab (B) toward the power cor d retainer (C) to release the power supply . Pull the power supply away from the system, as shown in Figur e 1. If you want to replace the power supply you r emoved, see “Replacing the 91 17-MMB or 9179-MHB power supply with the power turned off” on page 4. Figure 1. Removing the power supply 2 Power Sys[...]

  • Page 15

    Related information Before you begin Identifying a failing part Stopping the system or logical partition Removing the 91 17-MMB or 9179-MHB power supply with the power turned on Learn how to remove a power supply with the system power turned on if you want to r eplace a failing power supply , or as a part of another service action. Attention: T wo [...]

  • Page 16

    Note: When you remove a power supply with the system power turned on, an err or is logged. No action is requir ed for this error . If you want to replace the power supply you r emoved, see “Replacing the 91 17-MMB or 9179-MHB power supply with the power turned on” on page 6. Related information Before you begin Identifying a failing part Replac[...]

  • Page 17

    3. Connect the power cable A to the power supply . Note: This system is equipped with a second power supply . Before continuing with this procedur e, connect all power sources to the system. 4. Start the system, as described in Starting the system or logical partition. 5. Note the state of the light-emitting diodes (LEDs) on the power supply . For [...]

  • Page 18

    6. Close the rear rack door . Related information Starting the system or logical partition Replacing the 91 17-MMB or 9179-MHB power supply with the power turned on Learn how to replace a power supply with the system power turned on. Attention: T wo power supplies must be present in the system to power on the system unit. If one power supply fails,[...]

  • Page 19

    Attention: v Attach a wrist strap to an unpainted surface of your hardwar e to prevent electrostatic dischar ge (ESD) from damaging your har dware. v When using a wrist strap, follow all electrical safety procedur es. A wrist strap is for static control. It does not increase or decr ease your risk of receiving electric shock when using or working o[...]

  • Page 20

    7. Close the rear rack door . Related information Before you begin Power supply LEDs The various states of the power supply light-emitting diodes (LEDs) can be used to identify or verify a power supply that you are servicing. The power supply has three LEDs that indicate the power supply status: v an ac power LED (green, at the right of the 3 LEDs)[...]

  • Page 21

    v If the error and identify function (amber) LED is flashing, the ac power LED is on solid and the dc power LED is off, the power supply is not operating corr ectly and has been identified for replacement. Power supplies, fans, and input power distribution assemblies in a 5802 or 5877 expansion unit Learn about removing and r eplacing a power suppl[...]

  • Page 22

    light-emitting diode (LED) (A) as shown in Figure 7. A lit (flashing or on solid) LED indicates the failing power supply . 5. For the power supply that you want to remove, slide the cable r etention bracket to the open position (A) , and then disconnect the power cable (B) as shown in Figure 8. By moving the bracket to the open position, you turn t[...]

  • Page 23

    Attention: v Attach a wrist strap to an unpainted surface of your hardwar e to prevent electrostatic dischar ge (ESD) from damaging your har dware. v When using a wrist strap, follow all electrical safety procedur es. A wrist strap is for static control. It does not increase or decr ease your risk of receiving electric shock when using or working o[...]

  • Page 24

    a. T o identify the failing fan. press the fan identify button (A) , as shown in Figur e 10. An amber left or right fan-fault LED (C) on solid, as shown in Figure 1 1, indicates the faulty fan. b. Loosen the thumbscrew (A) that holds the fan in the power -supply assembly , as shown in Figure 1 1. Figure 10. Fan fault LED and fan identify button Fig[...]

  • Page 25

    c. Use the recessed fan handle (B) to lift the fan fr om the power-supply assembly , as shown in Figure 1 1 on page 12. If you removed the power supply or fan as part of another service action, or if you want to r eplace the power supply or fan that you removed fr om an expansion unit, see Replacing a power supply or fan in a 5802 or 5877 expansion[...]

  • Page 26

    6. At the front of the expansion unit, slide the cable r etention bracket for the power supply that you want to remove, to the open position (A) . Disconnect the cable (B) as shown in Figur e 13. 7. Attach the wrist strap. Attention: v Attach a wrist strap to an unpainted surface of your hardwar e to prevent electrostatic dischar ge (ESD) from dama[...]

  • Page 27

    9. Optional: If you want to remove a failing power -supply fan, complete the following steps: Note: If a fan fails, the amber fan fault LED on the front of the Of fline Converter Assembly (OCA) (B) , shown in Figure 15, is on solid. Figure 14. Removing a power supply Figure 15. Fan fault LED and fan identify button Power supplies 15[...]

  • Page 28

    a. Identify the failing fan by pressing the fan identify button (A) shown in Figur e 15 on page 15. An amber left or right fan-fault LED (C) on solid, as shown in Figure 16, indicates the faulty fan. b. Loosen the thumbscrew (A) that holds the fan in the power -supply assembly , as shown in Figure 16. c. Use the recessed fan handle (B) to pull the [...]

  • Page 29

    If your system is managed by the IBM Systems Director Management Console (SDMC), use the SDMC to replace a power supply in the server . For instructions, see Replacing a part by using the Systems Director Management Console. Determine if you are able to perform this procedure concurrently Attention: T wo power supplies must be present in the expans[...]

  • Page 30

    6. T o replace the power supply , with the locking handle (A) in the open position, push the power supply into the expansion unit as shown in Figure 18. 7. Close the locking handle (A) until the power supply locks into position. Figure 17. Replacing a fan Figure 18. Replacing a power supply 18 Power Systems: Power supplies for the 91 17-MMB or 9179[...]

  • Page 31

    8. Reconnect the power cable (A) to the front of the power supply , and then slide the cable retention bracket (B) to the closed position to secure the cable as shown in Figur e 19. By moving the bracket to the closed position, you turn on the power supply . 9. Note the state of the green ac power in (A) and Of fline Converter Assembly (OCA) power [...]

  • Page 32

    Note: If you replaced a power -supply fan as part of this procedure, note the state of the fan fault LED (B) shown in Figure 21. If the LED is off, indicating that both fans are operating normally , continue to the next step. If not, remove the power -supply assembly from the expansion unit and repeat the pr ocedure starting with step 5 on page 17.[...]

  • Page 33

    Related information Before you begin Replacing a power supply or fan in a 5802 or 5877 expansion unit with power turned off Learn how to replace a power supply or power -supply fan in a 5802 or 5877 expansion unit if you removed a failing part and want to r eplace the power supply assembly with the power turned off. If your system is managed by the[...]

  • Page 34

    c. T ighten the thumbscrew (D) as shown in Figur e 22. 6. T o replace the power supply , with the locking handle (A) in the open position, push the power supply into the expansion unit as shown in Figure 23 on page 23. 7. Close the locking handle (A) until the power supply locks into position. Figure 22. Replacing a fan 22 Power Systems: Power supp[...]

  • Page 35

    8. Connect the power cable (A) to the front of the power supply , and then slide the cable retention bracket (B) to the closed position to secure the cable as shown in Figur e 24. 9. Start the system, as described in Starting the system or logical partition. Figure 23. Replacing a power supply Figure 24. Connecting the power cable to the front of a[...]

  • Page 36

    10. Note the state of the green ac power in (A) and Of fline Converter Assembly (OCA) power (B) light-emitting diodes (LEDs) shown in Figure 25, and do one of the following actions, as applicable: v If the LEDs indicate that the power supply is operating normally , that is, that the ac power in LED (A) is on solid and the OCA power (B) LED is on so[...]

  • Page 37

    11 . V erify the installed part, as described in V erifying the installed part. 12. Close the front rack door . Continue with any other service actions you need to perform. Related information Starting the system or logical partition V erifying the installed part Removing an input power distribution assembly from a 5802 or 5877 expansion unit with [...]

  • Page 38

    5. At the rear of the expansion unit, disconnect both of the power cables, as shown in Figur e 27. 6. Attach the wrist strap. Attention: v Attach a wrist strap to an unpainted surface of your hardwar e to prevent electrostatic dischar ge (ESD) from damaging your har dware. v When using a wrist strap, follow all electrical safety procedur es. A wris[...]

  • Page 39

    8. Loosen the thumbscrew (B) on the input power distribution assembly . Pull out the assembly from the expansion unit, as shown in Figure 29. Figure 28. Removing an input power distribution assembly cover Figure 29. Removing an input power distribution assembly Power supplies 27[...]

  • Page 40

    T o replace an input power distribution assembly , see “Replacing an input power distribution assembly in a 5802 or 5877 expansion unit with the power turned off.” Related information Before you begin Identifying a failing part Stopping the system or logical partition Replacing an input power distribution assembly in a 5802 or 5877 expansion un[...]

  • Page 41

    6. Replace the input power distribution assembly cover , and then tighten the thumbscr ew (A) as shown in Figure 31. Figure 30. Replacing an input power distribution assembly Figure 31. Replacing an input power distribution assembly cover Power supplies 29[...]

  • Page 42

    7. At the rear of the expansion unit, connect both of the power cables, as shown in Figur e 32. 8. Close the rear rack door . 9. Start the system, as described in Starting the system or logical partition. 10. V erify the installed part, as described in V erifying the installed part. Continue with any other service actions you want to perform. Relat[...]

  • Page 43

    T o replace an input power distribution assembly in an expansion unit for a system that is not managed by the HMC or SDMC, complete the following steps: 1. If you are r eplacing an input power distribution assembly because of a failure, remove the failing part, as described in “Removing an input power distribution assembly from a 5802 or 5877 exp[...]

  • Page 44

    7. At the rear of the expansion unit, connect both of the power cables, as shown in Figur e 32 on page 30. Figure 34. Replacing an input power distribution assembly cover Figure 35. Connecting the power cables at the rear of an expansion unit 32 Power Systems: Power supplies for the 91 17-MMB or 9179-MHB[...]

  • Page 45

    8. Close the rear rack door . 9. Start the system, as described in Starting the system or logical partition. 10. V erify the installed part, as described in V erifying the installed part. Continue with any other service actions you want to perform. Related information Starting the system or logical partition Stopping the system or logical partition[...]

  • Page 46

    DANGER When working on or around the system, observe the following precautions: Electrical voltage and current from power , telephone, and communication cables are hazardous. T o avoid a shock hazard: v Connect power to this unit only with the IBM provided power cord. Do not use the IBM provided power cord for any other product. v Do not open or se[...]

  • Page 47

    Observe the following precautions when working on or around your IT rack system: v Heavy equipment–personal injury or equipment damage might result if mishandled. v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v T o avoid hazardous conditions due to uneven mechanical loading, always[...]

  • Page 48

    Blue or terra-cotta on a part of the hardwar e indicates a touch point where you can grip the hardwar e to remove it fr om or install it in the system, open or close a latch, and so on. T erra-cotta might also indicate that the part can be removed and r eplaced with the system or logical partition power on. 5. Ensure that you have access to a mediu[...]

  • Page 49

    v A : Power-on button v B : Power LED – A constant light indicates full system power to the unit. – A blinking light indicates standby power to the unit. Note: There is appr oximately a 30-second transition period from the time the power-on button is pressed to when the power LED goes fr om blinking to solid. During the transition period, the L[...]

  • Page 50

    Related concepts Identifying a failing part Use these instructions to learn how to locate and identify a failing part on your system or expansion unit using the appropriate method for your system. Identifying a failing part in an AIX system or logical partition Use these instructions to learn how to locate a failing part, and then activate the indi[...]

  • Page 51

    Identifying a failing part in an IBM i system or logical partition Y ou can activate or deactivate the indicator light by using IBM i to assist in locating a failing part. Activating the failing-part indicator light: Y ou can search the service action log for an entry that matches the time, r eference code, or r esource of a problem, and then activ[...]

  • Page 52

    3. T ype your service tools user ID and service tools password on the System Service T ools (SST) Sign On display . Press Enter . Remember: The service tools password is case-sensitive. 4. Select Start a service tool from the System Service T ools (SST) display and press Enter . 5. Select Hardware service manager from the Start a Service T ool disp[...]

  • Page 53

    4. Record the location information. Note: IBM provides har dware diagnostic aids and productivity tools, as well as installation aids for Linux operating systems on IBM Power systems. See Service and productivity tools for Linux on Power Systems servers Activating the indicator light for the failing part: If you know the location code of the failin[...]

  • Page 54

    Use these instructions to turn on the indicator light to help you physically locate a part by using the V irtual I/O Server (VIOS). 1. Log in as root user . 2. At the command line, type diagmenu and press Enter . 3. From the Function Selection menu, select T ask Selection . Press Enter . 4. From the T ask Selection menu, select Identify and Attenti[...]

  • Page 55

    v B : Power LED – A constant light indicates full system power to the unit. – A blinking light indicates standby power to the unit. Note: There is appr oximately a 30-second transition period from the time the power-on button is pressed to when the power LED goes fr om blinking to solid. During the transition period, the LED might blink faster [...]

  • Page 56

    Starting a system or virtual server with the Systems Director Management Console Y ou can use the IBM Systems Director Management Console (SDMC) user interface to start the system or virtual server after the requir ed cables are installed and the power cables are connected to a power source. For instructions on working with the SDMC, see Managing a[...]

  • Page 57

    Important: The system is equipped with a second power supply . Before continuing with this procedur e, ensure that all power sources to the system have been disconnected. (L003) or Stopping a system by using the Hardware Management Console Y ou can use the Hardwar e Management Console (HMC) user interface to stop the system or a logical partition. [...]

  • Page 58

    3. In the Contents area, select the managed system. 4. Select T asks , then Operations , and then Power Off 5. Select the appropriate power -off mode and click OK . Related information Shutting down and restarting logical partitions Stopping a system with the Systems Director Management Console Y ou can use the IBM Systems Director Management Conso[...]

  • Page 59

    Note: Replacing the shipping screws is optional but should be done in geographic ar eas that are prone to seismic activity . 4. While holding the system unit release latches (A) down on both the left and right sides, pull the system unit (B) out from the rack until the rails ar e fully extended and locked. Figure 38. Placing the system in the servi[...]

  • Page 60

    Placing the rack-mounted 8202-E4B or 8205-E6B system into the operating position Use this procedur e to place the rack-mounted system into the operating position. When placing the system into operating position, ensure that the cables at the back of the system do not catch or bind as you push the system unit back into the rack. 1. Unlock the blue r[...]

  • Page 61

    Removing and replacing covers for the 8202-E4B or 8205-E6B Use these instructions to r emove, replace, or install covers to access components or perform service. Removing the front cover on a rack-mounted 8202-E4B or 8205-E6B system Use this procedur e to remove the cover to access components or perform service. T o remove the fr ont cover , follow[...]

  • Page 62

    Removing the front cover on a stand-alone 8202-E4B or 8205-E6B system Use this procedur e to remove the cover to access components or perform service. T o remove the fr ont cover , follow these steps: 1. Open the front door (A) by swinging it towar ds the left as shown in the following figure. 2. Press latch (B) and pull the cover away fr om the sy[...]

  • Page 63

    Installing the front cover on a rack-mounted 8202-E4B or 8205-E6B system Use this procedur e to install the cover to access components or perform service. T o install the front cover , follow these steps: 1. Push the cover onto the system. 2. Gently push the cover in until the four cover clips are seated in their r espective mounting posts as shown[...]

  • Page 64

    Installing the front cover and front door on a stand-alone 8202-E4B or 8205-E6B system Use this procedur e to install the cover to access components or perform service. T o install the front cover and fr ont door , complete the following steps. 1. Align the cover (A) until the two cover tabs are seated into the slots on the base plate (B) , as show[...]

  • Page 65

    3. Hold the front door at an appr oximate 120 degree angle to the system as show in the following figure. Engage the latches. Removing the service access cover on a rack-mounted 8202-E4B or 8205-E6B system Use this procedur e to remove the service access cover . 1. Loosen the two thumbscrews (A) located at the back of the cover . 2. Slide the cover[...]

  • Page 66

    Attention: When the service access cover is removed, the system powers down. Removing the service access cover on a stand-alone 8202-E4B or 8205-E6B system Use this procedur e to remove the service access cover . 1. Loosen the thumbscrew (A) located at the back of the outside cover . 2. Slide the cover (B) toward the back of the system unit. When t[...]

  • Page 67

    3. Loosen the two thumbscrews (A) located at the back of the inside cover . 4. Slide the cover (B) toward the back of the system unit. When the fr ont of the service access cover has cleared the upper frame ledge, lift the cover up and of f the system unit. Attention: When the service access cover is removed, the system powers down. Figure 47. Inst[...]

  • Page 68

    Installing the service access cover on a rack-mounted 8202-E4B or 8205-E6B system Use this procedur e to install the service access cover . 1. Place the service access cover on top of the system, about 25 mm (1 in.) from the upper chassis ledge. 2. Hold the service access cover against the system unit and slide it toward the fr ont of the system. T[...]

  • Page 69

    5. Place the outside service access cover (A) on top of the system. 6. Hold the service access cover against the system unit and slide it toward the fr ont of the system. The tabs of the service access cover slide beneath the upper chassis ledge. 7. Align the thumbscrew (B) located on the back of the service access cover with the hole on the back o[...]

  • Page 70

    Disconnecting the power cords from the 8202-E4B or 8205-E6B system Use these procedur es to disconnect the power cords from the 8202-E4B or 8205-E6B system. 1. For a rack-mounted system, open the back rack door on the unit you are servicing and identify the system unit you are servicing in the rack. 2. For both a rack-mounted system and a stand-alo[...]

  • Page 71

    Figure 52. Removing the power cords for a rack-mounted system Figure 53. Removing the power cords for a stand-alone system Power supplies 59[...]

  • Page 72

    Connecting the power cords to the 8202-E4B or 8205-E6B system Use this procedur e to connect the power cords. 1. Identify the system unit you are servicing in the rack. 2. Connect all power cords to the unit you ar e servicing. Ensure that the cords ar e threaded thr ough the handles. 3. Close the back rack door . Installing a feature by using the [...]

  • Page 73

    Note: The HMC might open external instructions for installing the featur e. If so, follow those instructions to install the featur e. Installing a part by using the Systems Director Management Console Y ou can use the IBM Systems Director Management Console (SDMC) to perform many service actions, including the installation of a new field-replaceabl[...]

  • Page 74

    v Y es: The new device is installed corr ectly . Exit the diagnostic programs and return the system to normal operations. V erify the replacement part by using AIX: T o verify the operation of a newly installed feature or r eplacement part, follow these steps: 1. Did you use either the AIX operating system or the online diagnostics service aid conc[...]

  • Page 75

    v Y es: Select Log Repair Action , if not pr eviously logged, from the T ask Selection menu to update the AIX error log. If the r epair action was reseating a cable or adapter , select the r esource associated with that repair action. If the r esource associated with your action is not displayed on the resour ce list, select sysplanar0 and press En[...]

  • Page 76

    V erifying the installed part in an IBM i system or logical partition If you have installed a new feature or part, verify that the system r ecognizes the feature or part by using the IBM i system service tools. T o verify the installed part, follow these steps: 1. Deactivate the failing item indicator light. For instructions, see “Deactivating th[...]

  • Page 77

    v Failing item list 9. Select option 2 (Display failing item information) to display the service action log entry . 10. Select option 2 (Display details) to display location information for the failing part to be replaced. The information displayed in the date and time fields is the date and time for the first occurrence of the specific System refe[...]

  • Page 78

    T ip: If a service request number (SRN) or other r eference code is displayed, suspect a loose adapter or cable connection. Note: If you received an SRN or any other r eference code when you attempted to start the system, contact your service provider for assistance.. 8. If the terminal type is requested, select the Initialize T erminal option on t[...]

  • Page 79

    6. Click Close Event . 7. Add comments for the serviceable event. Include any unique additional information. Click OK . 8. Did you replace, add, or modify a field r eplaceable unit (FRU) of the open service action event? v No : Select the No FRU Replaced for this Serviceable Event option, and click OK to close the service action event. v Ye s : Per[...]

  • Page 80

    v Identify LED for an enclosure If you want to add an adapter to a specific drawer (enclosure), you need to know the machine type, model, and serial number (MTMS) of the drawer . T o determine whether you have the correct MTMS for the drawer that needs the new adapter , you can activate the LED for a drawer and verify that the MTMS corresponds to t[...]

  • Page 81

    6. When you are finished, click Cancel twice to close the Serviceable Event Details window and the Serviceable Event Overview window . V erifying the installed part by using Systems Director Management Console If you installed or replaced a part, use the IBM Systems Dir ector Management Console (SDMC) to update your SDMC recor ds after you have com[...]

  • Page 82

    v An indication that you cannot activate the system attention LED. 4. Select one of the virtual servers, and select Deactivate System Attention LED . A confirmation window is displayed that provides the following information: v A verification that the system attention LED was deactivated. v An indication that there still might be open pr oblems wit[...]

  • Page 83

    v V erifying the replaced part using VIOS V erify the installed feature by using VIOS: 1. Log in as root user . 2. At the command line, type diagmenu and press Enter . 3. Select Advanced Diagnostics Routines and press Enter . 4. From the Diagnostic Mode Selection menu, select System V erification and press Enter . 5. When the Advanced Diagnostic Se[...]

  • Page 84

    b. Select Commit . c. Follow any instructions that ar e shown. d. I fa Do you want to review the previously displayed err or? message is shown, select Ye s and press Enter . e. If an SRN is shown, suspect a loose card or connection. If no obvious pr oblem is shown, record the SRN and contact your service provider for assistance.. f. If no SRN is sh[...]

  • Page 85

    a. From the Resource Repair Action menu, select the par ent or child of the resource that has been replaced. If the r epair action was to reseat a cable or adapter , select the resour ce associated with that repair action. If the r esource associated with your action does not appear on the Resource List, select sysplanar0 . Press Enter . b. Select [...]

  • Page 86

    4. Choose from the following options: v If the original problem was a failing disk drive that contained the operating system softwar e, go to step 5. v If the original problem was that the operating system would not load and you have another FRU to r eplace, go to your FRU locations section to locate the next FRU. v If the next FRU in the FRU list [...]

  • Page 87

    Perform the following steps: 1. If the system is not powered on, power it on now . 2. Perform a slow boot. 3. W ait until the AIX operating system login pr ompt displays or until system activity on the operator panel or display apparently has stopped. 4. Did you encounter any problems? No Continue at step 6. Ye s If the original problem still exist[...]

  • Page 88

    Ye s Use the Log Repair Action option, if not previously logged, in the T ASK SELECTION menu to update the AIX error log. If the repair action was r eseating a cable or adapter , select the resour ce associated with that repair action. If the resour ce associated with your action is not displayed on the resour ce list, select sysplanar0 . Note: If [...]

  • Page 89

    1. From the RESOURCE REP AIR ACTION menu, select the parent or child of the resour ce that has been replaced. If the r epair action was reseating a cable or adapter , select the resource associated with that repair action. If the r esource associated with your action is not displayed on the resour ce list, select sysplanar0 . 2. Press COMMIT after [...]

  • Page 90

    Y es: Continue with the next step. No: Continue with step 6. 4. Select the IPL type and mode for the system or logical partition that the customer uses (see IPL type mode and speed options in the Service functions). 5. Start an IPL by powering on the system or partition (see Powering on and powering off). Did the system complete the IPL? Y es: Cont[...]

  • Page 91

    Y es: Perform the verification pr ocedures in the Service functions to verify that the pr oblem is corrected. After the verification test is complete, the tape device description will be set to the failed state because a resour ce change was detected. Perform the following tasks: - V ary the tape device description off and then on. - Return the sys[...]

  • Page 92

    v If the repair was done using the HMC online r epair procedures, ensur e that the original serviceable event is now closed. 1. Is a management console used to manage the server that you are servicing? v Y es: Continue with the next step. v No: Return to the “V erifying a repair” on page 73. This ends the procedure. 2. Are you closing a service[...]

  • Page 93

    v Return the server to the state that the customer normally uses such as IPL type, IPL mode, and the way the system is configured or partitioned. Attention: Before r eturning the system to the customer , remove the system from service mode. If the system is left in service mode, it automatically places a call for service every two hours. v While yo[...]

  • Page 94

    v Y es: Continue with the next step. v No: Go to step 1 1. 9. Is the FRU list identical (same FRUs, same number of FRUs, and same order of FRUs) to the FRU list of the error code r ecorded in step 1 on page 81? v Y es: Go to step 1 1. v No: Continue with the next step. 10. The FRU list is differ ent. Is the FRU you replaced and recor ded in step 1 [...]

  • Page 95

    19. Add comments for the serviceable event. Include any unique additional information. Click OK . The following steps will add or update FRU information. 20. Did you replace, add, or modify a FRU of the open service action event? v Y es: Continue with the next step. v No: Go to step 22. 21. From the FRU list, select a FRU that you need to update. D[...]

  • Page 96

    1. Press Enter . 2. Select the T ask Selection option. 3. Select the Log Repair option. 4. Select the resour ce associated with the repair action. If the r epair action was reseating a cable or adapter , select the resource associated with that repair action. If the r esource associated with your repair action is not displayed on the Resour ce List[...]

  • Page 97

    1. Press Enter . 2. Select the T ask Selection option. Note: If the terminal type is not defined, you are pr ompted to define it before you can pr oceed. 3. Select the Log Repair option. 4. Select the resour ce associated with the repair action. If the r epair action was reseating a cable or adapter , select the resource associated with that repair[...]

  • Page 98

    2. Do you have any field-replaceable units (FRUs) (for example car ds, adapters, cables, or devices) that were r emoved during problem analysis that you want to put back into the system? Note: If the system planar or battery has been replaced and you ar e loading diagnostics from a server over a network, it might be necessary for the customer to se[...]

  • Page 99

    1. If the system supports slow boot (see Performing a slow boot), do a slow boot on the system. If the system does not support slow boot, do a normal boot. 2. Power on the system. 3. W ait until the AIX operating system login pr ompt displays or until system activity on the operator panel or display apparently has stopped. Did the AIX Login Prompt [...]

  • Page 100

    If the resour ce associated with your action is not displayed on the resour ce list, select sysplanar0 . Note: If the system attention indicator is on, this will set it back to the normal state. Go to step 14. 12. When a test is run on a r esource in system verification mode, and that r esource has an entry in the AIX error log, if the test on the [...]

  • Page 101

    Did you perform service on a RAID subsystem involving changing of the PCI RAID adapter cache card or changing the configuration? Note: This does not refer to the PCI-X RAID adapter or cache. v Y es: Continue with the next step. v No: Go to step 16. 15. Use the Recover Options selection to resolve the RAID configuration. T o do this, do the followin[...]

  • Page 102

    3. Are ther e any service action events that are open? v Y es: Continue with the next step. v No: If the system attention LED is still on, turn off the LED as described in “Activating and deactivating LEDs” on page 93. Return the system to the customer . This completes the repair . 4. Record the list of open service action events. 5. From the l[...]

  • Page 103

    v Y es: Continue with the next step. v No: Go to step 17. 13. Have you begun a list of A xx partitions from prior service action events that you pr ocessed in this maintenance analysis procedur e (MAP)? v Y es: Go to step 15. v No: Continue with the next step. 14. Begin a new list of A xx partitions by copying the list of partitions obtained in ste[...]

  • Page 104

    v Y es: Continue with the next step. v No: Go to step 30. 24. Is the error class r ecorded in step 23 on page 91? v Y es: Continue with the next step. v No: Go to step 30. 25. Perform the following steps for each entry in the list of all partitions you recor ded in step 1 1 on page 90, except the partition you were using to debug the original pr ob[...]

  • Page 105

    32. Perform the following steps for each entry in the list of A xx partitions you began recor ding in step 14 on page 91, except the partition you were using to debug the original pr oblem. 33. From the IVM virtual terminal window of a partition in the list of A xx partitions, type diag at the AIX command prompt. 34. When the diagnostic operating i[...]

  • Page 106

    v “Activating or deactivating an identify LED using the Advanced System Management Interface” on page 96 Deactivating a system attention LED or partition LED using the management console Y ou can deactivate a system attention LED or a logical partition LED if you decide that a problem is not a high priority and you decide to repair the pr oblem[...]

  • Page 107

    v Identify LED for a FRU associated with a specified enclosure If you want to hook up a cable to a specific I/O adapter , you can activate the LED for the adapter , which is a field replaceable unit (FRU), and then physically check to see where you should hook up the cable. This is especially useful when you have several adapters with open ports. T[...]

  • Page 108

    Activating or deactivating an identify LED using the Advanced System Management Interface Y ou can activate or deactivate an identify LED using the Advanced System Management Interface (ASMI). Y ou can specify the location code of any indicator to view or modify its current state. If you pr ovide the wrong location code, the advanced system manager[...]

  • Page 109

    Notices This information was developed for products and services of fered in the U.S.A. The manufacturer may not of fer the products, services, or features discussed in this document in other countries. Consult the manufacturer's r epresentative for information on the products and services currently available in your ar ea. Any r eference to t[...]

  • Page 110

    This information is for planning purposes only . The information herein is subject to change before the products described become available. This information contains examples of data and reports used in daily business operations. T o illustrate them as completely as possible, the examples include the names of individuals, companies, brands, and pr[...]

  • Page 111

    generates, uses, and can radiate radio frequency ener gy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer ence to radio communications. Operation of this equipment in a residential ar ea is likely to cause harmful interference, in which case the user will be requir ed to correct the interference a[...]

  • Page 112

    This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interfer ence may occur , in which case, the user may be required to take corrective actions. Japanese Electronics and Information T echnology Industries Association (JEIT A) Confirmed Harmonics Guideline (products less th[...]

  • Page 113

    Electromagnetic Interference (EMI) Statement - Korea Germany Compliance Statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse A EU-Richtlinie zur Elektromagnetischen V erträglichkeit Dieses Produkt entspricht den Schutzanfor derungen der EU-Richtlinie 2004/108/EG zur Angleichung der Rechtsvorschriften über die elektromagnetische[...]

  • Page 114

    V erantwortlich für die Einhaltung der EMV V orschriften ist der Hersteller: International Business Machines Corp. New Orchar d Road Armonk, New Y ork 10504 T el: 914-499-1900 Der verantwortliche Ansprechpartner des Herstellers in der EU ist: IBM Deutschland GmbH T echnical Regulations, Abteilung M456 IBM-Allee 1, 71 139 Ehningen, Germany T el: +4[...]

  • Page 115

    any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful [...]

  • Page 116

    Japanese Electronics and Information T echnology Industries Association (JEIT A) Confirmed Harmonics Guideline with Modifications (products greater than 20 A per phase) IBM T aiwan Contact Information Electromagnetic Interference (EMI) Statement - Korea Germany Compliance Statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse B EU-[...]

  • Page 117

    Dieses Gerät ist berechtigt, in Über einstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen. V erantwortlich für die Einhaltung der EMV V orschriften ist der Hersteller: International Business Machines Corp. New Orchar d Road Armonk, New Y ork 10504 T el: 914-499-1900 Der verantwortliche Ansprechpartner des Herstellers [...]

  • Page 118

    106 Power Systems: Power supplies for the 91 17-MMB or 9179-MHB[...]

  • Page 119

    [...]

  • Page 120

     Printed in USA[...]