Husqvarna 333R manual

E E E E n n n n g g g g l l l l i i i i s s s s h h h h 333R 335R X-series Oper ator’ s manual (EP A) Please r ead the operator’ s manual carefully and mak e sure y ou understand the instructions before using the machine.[...]

2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear: • A protectiv[...]

English – 3 CONTENTS Contents Note the f ollowing bef ore starting: Long-ter m e xposure to noise can result in per manent hearing impairment. So alwa ys use approv ed hear ing protection. Maintenance, replacement, or repair of the emission control de vices and system may be perf ormed by any nonroad engine repair establishment or individual. Thi[...]

4 – English INTR ODUCTION Dear customer! Cong ratulations on y our choice to buy a Husqv ar na product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River , f or production of muskets . The location was logical, since w ater power was h[...]

English – 5 WHA T IS WHA T? What is what on the c learing saw? 34 34 33 23 R 1 T r immer head 2 Grease fi ller cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop s witch 9 Throttle lock 10 Suspension 11 Cylinder cov er 12 Star ter handle 13 Fuel tank 14 Choke control 15 Air purge 16 Air fi l[...]

6 – English GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PRO TECTION W ear hear ing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection. If you use a visor then you m ust also wear[...]

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′ ′ ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine [...]

8 – English GENERAL SAFETY PRECA UTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to reduce vibration and mak e operation easier . Using incorrectly wound cord or a b lunt or incorrect cutting attachment (wrong type or incorrectly fi led, see instructions under the heading Filing the blad[...]

English – 9 GENERAL SAFETY PRECA UTIONS Regularly check that the muf fl er is securely attached to the machine. If the muf fl er on y our machine is fi tted with a spar k arrestor mesh this must be cleaned regularly . A block ed mesh will cause the engine to ov erheat and may lead to serious damage. Loc king nut A locking n ut is used to secur[...]

10 – English GENERAL SAFETY PRECA UTIONS Cutting equipment Saw b lades are intended for cutting fi brous types of w ood. Grass b lades and grass cutters are intended f or cutting coarse grass . A trimmer head is intended for trimming grass . General rules Only use cutting attachments with the guards we recommend! See the chapter on T echnical da[...]

English – 11 GENERAL SAFETY PRECA UTIONS Adjust the blade setting. This should be 1 mm. T rimmer head • Only use the recommended trimmer heads and tr immer cords. These hav e been tested by the manuf acturer to suit a par ticular engine size. This is especially impor tant when a fully automatic trimmer head is used. Only use the recommended cut[...]

12 – English ASSEMBL Y Assembling the handlebar and thr ottle • Remov e the screw at the rear of the throttle handle . • Slide the throttle handle onto the right side of the handlebar , (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar . •R e fi t the screw in the hole in the rear of the throttle[...]

English – 13 ASSEMBL Y Fitting a blade guar d, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fi tting on the shaft and secure with the bolt. CA UTION! Ensure that the guard e xtension is removed. Use the recommended blade guard. See the T echnical data section. • Fit the drive disc (B) on the output shaft[...]

14 – English ASSEMBL Y • When loosening and tightening the saw b lade nut, there is a risk of injur y from the teeth of the saw blade . Y ou should theref ore alwa ys ensure that your hand is shielded by the blade guard when doing this . Alwa ys use a sock et spanner with a shaft that is long enough to allow this . The arrow in the diagr am sho[...]

English – 15 ASSEMBL Y Adjusting the harness and c learing saw Standar d harness Quic k release At the front is an easily accessible , quick release . Use this if the engine catches fi re or in any other emergency situation that requires you to free y ourself from the machine and harness. Spreading the load on y our shoulders A well-adjusted har[...]

16 – English FUEL HANDLING Fuel safety Ne ver star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate . 2 If you ha ve spilt fuel on y ourself or your clothes , change your clothes . W ash any part of your body that has come in contact with fuel. Use soap and w ater . 3 If the machine is l[...]

English – 17 FUEL HANDLING Mixing • Alwa ys mix the gasoline and oil in a clean container intended f or fuel. • Alwa ys star t by fi lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly bef ore fi l[...]

18 – English ST AR TING AND ST OPPING Chec k before starting • Check the b lade to ensure that no cracks ha ve f ormed at the bottom of the teeth or by the centre hole . The most common reason wh y cracks are f ormed is that shar p corners have been f ormed at the bottom of the teeth while shar pening or that the blade has been used with dull t[...]

English – 19 ST AR TING AND ST OPPING Hold the body of the machine on the ground using y our left hand (CA UTION! Not with your f oot!). Gr ip the star ter handle, slowly pull out the cord with y our right hand until you feel some resistance (the star ter pawls grip), now quic kly and powerfully pull the cord. Never wrap the starter cord ar ound [...]

20 – English W ORKING TECHNIQUES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out b y the cutting at[...]

English – 21 W ORKING TECHNIQUES W orking methods • Bef ore you star t clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollo ws etc. • Star t at whichev er end of the area is easiest, and clear an open space from which to work. • W or k systematically to and fro across the area, cle[...]

22 – English W ORKING TECHNIQUES • Large stems must be cut from two sides . First determine which direction the stem will f all. Make the fi rst cut on the f elling side. Then fi nish cutting the stem from the other side. Adjust the cutting pressure to match the size of the stem and the hardness of the wood. Small stems require more pressure,[...]

English – 23 W ORKING TECHNIQUES Clearing • The clearing technique removes all unw anted vegetation. K eep the trimmer head just above the g round and tilt it. Let the end of the cord strike the ground around trees , posts, statues and the like . CA UTION! This technique increases the wear on the cord. • The cord wears quic ker and must be f [...]

24 – English MAINTENANCE Carb uretor Y our Husqv ar na product has been designed and manuf actured to speci fi cations that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. T o ensure that it continues to run at peak perf or mance and to minimise har mful exhaust emissions after the running-in pe[...]

English – 25 MAINTENANCE will run smoothly in ev er y position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. W ARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact y our dealer/ser vice workshop . Do not use the machine until it has been correctly adjust[...]

26 – English MAINTENANCE If the mesh is frequently bloc ked, this can be a sign that the perf or mance of the catalytic conv er ter is impaired. Contact your dealer to inspect the m uf fl er . A bloc ked mesh will cause the machine to ov erheat and result in damage to the cylinder and piston. CA UTION! Ne ver use a machine with a def ectiv e muf[...]

English – 27 MAINTENANCE Spark plug The spark plug condition is in fl uenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air fi lter . These f actors cause deposits on the spar k plug electrodes, which ma y result in operating problems and starting dif fi culties. If [...]

28 – English MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine. Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and ser vice work descr ibed in this manual. More extensiv e work must be carried out by an authorised ser vic[...]

English – 29 TECHNICAL D A T A T echnical data Note 1: Equiv alent noise pressure lev el is calculated as the time-weighted energy total f or noise pressure lev els under v ar ious working conditions with the follo wing time distribution: 1/2 idle and 1/2 max. speed. NO TE! Noise pressure at the user’ s ear and vibration on the handles are meas[...]

30 – English TECHNICAL D A T A Appro ved accessories T ype Cutting attachment guar d, Art. no. Centre hole in blades/cutters , Ø 25,4 mm Output shaft thread M12 Grass b lade/grass cutter Multi 255-3 (Ø 255 3 teeth) 537 33 16-01 Grass 255-4 (Ø 255 4 teeth) 537 33 16-01 Multi 275-4 (Ø 275 4 teeth) 537 33 16-01 Multi 300-3 (Ø 300 3 teeth) 537 3[...]

English – 31 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv arna Forest & Garden are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine . In U .S. and Canada, new small non[...]

1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm[...]

[...]

"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35[...]

1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5[...]

T35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm[...]

[...]

´®z+HAe¶5f¨ ´®z+HAe¶5f¨[...]

[...]

´®z+HAe¶5f¨ 2005-09-14 ´®z+HAe¶5f¨ 1140336-95[...]