HP (Hewlett-Packard) 686234-S01 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of HP (Hewlett-Packard) 686234-S01, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of HP (Hewlett-Packard) 686234-S01 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of HP (Hewlett-Packard) 686234-S01. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of HP (Hewlett-Packard) 686234-S01 should contain:
- informations concerning technical data of HP (Hewlett-Packard) 686234-S01
- name of the manufacturer and a year of construction of the HP (Hewlett-Packard) 686234-S01 item
- rules of operation, control and maintenance of the HP (Hewlett-Packard) 686234-S01 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of HP (Hewlett-Packard) 686234-S01 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of HP (Hewlett-Packard) 686234-S01, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the HP (Hewlett-Packard) service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of HP (Hewlett-Packard) 686234-S01.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the HP (Hewlett-Packard) 686234-S01 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    HP Pr oL iant ML3 1 0e G en8 Ser v er Maintenance an d Serv i ce G uide Abstract This docume nt is for an experienced servi ce technicia n. It is helpful if you are qualifie d in the servicing of comp uter equip ment and trained in recogn izing hazard s in produc ts w ith hazar dous energy level s an d are f amil iar with weight and st ability pr e[...]

  • Page 2

    © Copyright 2012 Hewlett - Packar d Dev elopme nt C ompany , L.P . The informa tion contained herei n is subj ect to chan ge with out notice . Th e only warr antie s for HP pr oduct s and servi ces ar e set f orth in the express warran ty st atemen ts accompan yin g such pro ducts and s ervic es. N othin g here in sh ould be con strue d as const i[...]

  • Page 3

    Contents 3 C ontents Customer self repair ...................................................................................................................... 6 Parts o nly warrant y service ............................................................................................................................ 6 Illustrated parts catalog ....[...]

  • Page 4

    Contents 4 HP Tru sted Platfor m M odule ......................................................................................................................... 60 Trouble shooti ng .......................................................................................................................... 61 Troub lesh ootin g res ou rces .........[...]

  • Page 5

    Contents 5 Before you contact HP ................................................................................................................................ 85 HP contact info rmation ................................................................................................................................ 85 Acronyms and abbreviations ..[...]

  • Page 6

    Customer self repair 6 C us tomer self r epair HP products are designed wi th many Customer Self Repa ir (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replac ement. If dur ing the diagn osis p eriod HP (o r HP servic e providers or service partners) identifies that the repair ca n be accomplishe[...]

  • Page 7

    Customer self repair 7 Obligatoire - Pièces pou r lesquelles la réparation par le client est obligatoire. Si vous demandez à H P de remplacer c es pièces, l es coûts de déplac ement et main d'œuvre du servic e vous ser ont factu rés. Facultatif - Pièces pour lesquell es la réparatio n par le client est f acultati ve. Ces pièces sont[...]

  • Page 8

    Customer self repair 8 In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il giorno lavorativo seguente. La consegna nel giorno stess o o entro quattro ore è o fferta con un supplemento di costo solo in alcune zone . In caso di necessità si può rich iedere l'assistenza t elefon ica di un[...]

  • Page 9

    Customer self repair 9 defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den Kurier - /Frachtdi enst. Weitere Informationen über das H P Customer Self Repair Programm erhalten Sie v on Ihrem Servi cep[...]

  • Page 10

    Customer self repair 10 enviara el componente defe ctuoso requerido , HP podrá cobrarle por el de sustituc ión. En el caso de toda s sustituc iones que l leve a cabo el client e, HP se hará c argo de todos los gasto s de envío y devoluc ión de componentes y escogerá la empresa de transporte que se utilice para dicho s ervicio. Para obtener m?[...]

  • Page 11

    Customer self repair 11 Neem contac t op met een Servic e Partner voor m eer inform atie over het C ustomer Self Rep air program ma van HP. Informatie over Service Partners vindt u op de HP website ( h ttp://www.h p.c om/go/selfrep air ). Gar antie se r v ice "P arts On l y" Het is mogelijk dat de HP garantie alleen de garantieserv ice &q[...]

  • Page 12

    Customer self repair 12 No caso desse serviç o, a subst ituição de peças CSR é obrigat ória. Se desejar que a HP substi tua essas peças, serão cobradas as despesas de transporte e mão - de - obra do serviço.[...]

  • Page 13

    Customer self repair 13[...]

  • Page 14

    Customer self repair 14[...]

  • Page 15

    Customer self repair 15[...]

  • Page 16

    Illustrated parts catalog 16 I llus tr ated par ts catalog M echanical c omponents Item Description Spare part number C ustom er s elf repai r (on page 6 ) 1 Access panel 686751 - 001 Mandatory 1 2 RPS cage 686665 - 0 01 Mandatory 1 3 Four - bay LFF d riv e cage 686745 - 001 Mandatory 1 4 SFF dri ve blank 670033 - 001 Mandator y 1 5 LFF driv e blan[...]

  • Page 17

    Illustrated parts catalog 17 2 Optional: Facultatif— Pièces pour lesqu elles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui - même la réparation. Toutefois, si vous demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, sel[...]

  • Page 18

    Illustrated parts catalog 18[...]

  • Page 19

    Illustrated parts catalog 19 S ystem compon ents Item Description Spare part numbe r Custom e r sel f repa ir (on page 6 ) 7 Optic al drive s — — a) SATA D VD - ROM drive 624591 - 001 Mandatory 1 b) SATA D VD - RW drive* 624592 - 0 01 Mandatory 1 8 Front I/O module 691939 - 001 Mandatory 1 9 Eight - bay SFF h ot - plug dri ve cag e asse mbly 68[...]

  • Page 20

    Illustrated parts catalog 20 Item Description Spare part numbe r Custom e r sel f repa ir (on page 6 ) d) 3 TB, 6G h ard dri ve* 628183 - 001 Mandator y 1 Non - hot - plug drives, SAS — — a) 450 GB, 6 G hard drive* 517353 - 001 Mandator y 1 b) 600 GB, 6 G hard drive* 517355 - 001 Mandator y 1 Hot - plug drives, SATA — — a) 100 GB, 3 G MLC s[...]

  • Page 21

    Illustrated parts catalog 21 Item Description Spare part numbe r Custom e r sel f repa ir (on page 6 ) j) 900 GB, 6G hard drive * 653971 - 001 Mandatory 1 k) 1 TB, 6G hard drive* 653954 - 001 Mandatory 1 14 Front s ystem fa n (80 x 38 mm) 686749 - 001 Mandatory 1 15 System bo ard assembl y (i nclude alcohol pad and ther mal com pound) 686757 - 001 [...]

  • Page 22

    Illustrated parts catalog 22 Item Description Spare part numbe r Custom e r sel f repa ir (on page 6 ) 26 Mini- SAS to SAT A cable assembly (for LFF drive c age) * 686747 - 001 Mandatory 1 *Not shown 1 Mandatory — Parts for whi ch customer sel f repair is m andatory. If you request HP to replace these parts, you will be charged f or the travel an[...]

  • Page 23

    Illustrated parts catalog 23 2 Optiona l: Optio neel — Onderd elen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen voor re paratie door de klant. Als u ec hter HP v erzoekt deze onderdelen voor u te ve rvangen , kunnen daarvoor extra kos ten in reke ning worden g ebracht, afh ankelijk van het type g arantieserv i[...]

  • Page 24

    Remov al and replac emen t procedures 24 R emo v al and r epla cement pr ocedur es R equired tool s You need the f ollowing i tems for som e procedu res: • T- 10/T - 15 Torx sc rewdri ver (on page 75 ) • Flathead sc rewdriver • HP Insight Diagnostics (on page 62 ) S afety consi derations Before perfor ming service pr ocedures, review all the [...]

  • Page 25

    Remov al and replac emen t procedu res 25 This symbol on an RJ - 45 receptacle indicates a network inte rface connection. WARNING: To redu ce the risk of electric sho ck, fire, or damage to the equipment, do not plug telephone or telecommunications connectors int o this receptacle. This symbol in dicates the pr esence of a ho t surface or hot c omp[...]

  • Page 26

    Remov al and replac emen t procedures 26 Prepar ation proce dures To access so me compo nents and perfo rm certai n service proc edures, p erform on e or more of the f ollowing procedu res: • Unlock th e tower bezel (on page 26 ). • Remove the tower bez el (on page 26 ). • Power down th e server (on page 27 ). Before removing the se rver from[...]

  • Page 27

    Remov al and replac emen t procedures 27 2. Pull the bezel away from the front c hassis. P ower down the server Before powering down the s erver for any upgrade or maintenance procedures , perform a backup of cri tical server data and programs. WARNING: To reduce the risk of perso nal inju ry, electric shock, or damage to the equipm ent, remove the[...]

  • Page 28

    Remov al and replac emen t procedures 28 CAUTION: To prevent improper cooling and thermal damage, do not operate the serv er unless all bays are populated with either a component or a blank. To remove the c omponent: 1. Unloc k and open th e tower bezel (" Unlock the to wer bezel " on page 26 ). 2. Do one of the foll owing: o In a non - h[...]

  • Page 29

    Remov al and replac emen t procedures 29 CAUTION: To prevent improper cooling and thermal damage, do not operate the serv er unless all bays are populated with either a component or a blank. To remove the c omponent: 1. Back up all server data on the drive. 2. Power do wn the server (on page 27 ). 3. Remove all po wer: a. Discon nect each po wer co[...]

  • Page 30

    Remov al and replac emen t procedures 30 2. Determine th e status of t he drive from th e drive LED definitions (on page 73 ). 3. Unloc k and open th e tower bezel (" Unloc k the tower bezel " o n page 26 ). 4. Remove the dri ve. To replace th e compon ent, reverse the rem oval procedu re. H ot - plug power supply CAUTION: To prevent impr[...]

  • Page 31

    Remov al and replac emen t procedures 31 CAUTION: The default and redu ndant power supplies in the server must have the same output power capacity. Verify that all power supplies have the same part number and label color. The sys tem becomes unstable and m ight shut down when it detects mismatched power supplies. To replace th e compon ent, reverse[...]

  • Page 32

    Remov al and replac emen t procedures 32 A ir baffle To remove the c omponent: CAUTION: For proper cooling, do not operate the server without the access panel, baffles, expansion slot covers, or blanks insta lled. If the server supports hot - plug component s, minimize the amoun t of time the acc ess panel is open. 1. Power do wn the server (on pag[...]

  • Page 33

    Remov al and replac emen t procedures 33 5. Disconnect the SATA and po wer cables fr om the opti cal drive. 6. Remove the optical drive. To replace th e compon ent, reverse the rem oval procedu re. D rive cage To remove the c omponent: 1. Power do wn the server (on page 27 ). 2. Remove all po wer: a. Discon nect each po wer cord from the power sou [...]

  • Page 34

    Remov al and replac emen t procedures 34 o Four - bay LFF drive cage o Eight - ba y SFF drive cage To replace th e compon ent, reverse the rem oval procedu re. To convert the four - bay non - hot - plug drive cage to a hot-plug model, remove the cage bracket, and then install the hot - plug backplane option before installing the cage back to the se[...]

  • Page 35

    Remov al and replac emen t procedures 35 b. Discon nect each po wer cord from the server. 3. Remove the to wer bezel (o n page 26 ). 4. Remove the ac cess panel (" Access pan el " on page 31 ). 5. If the drives are to be connected to a storage controller card, remove the air baffle (" Air baffle " on page 32 ). 6. Remove all ins[...]

  • Page 36

    Remov al and replac emen t procedures 36 o In a non - hot - plug drive cage, loosen the bra cket thum bscrew, and then rem ove the bra cket assembl y from the dr ive cage. o In a hot - plug drive cage, loosen the backplane thumbscrew, and then remove the backplane assembly from t he drive cag e. To replace th e compo nent, reverse the rem oval proc[...]

  • Page 37

    Remov al and replac emen t procedures 37 3. Unloc k and open th e tower bezel (" Unloc k the tower bezel " o n page 26 ). 4. Remove the ac cess panel (" Access pan el " on page 31 ). 5. Remove the air baffle (" Air baffle " on page 32 ). 6. Disconnect the front USB and LED cables from the system board (" Front pan[...]

  • Page 38

    Remov al and replac emen t procedures 38 7. Press the release latch, and then remove the fan module. To replace th e compon ent, reverse the rem oval procedu re. DIMMs G eneral DIMM slo t population guidelines • The server has fou r memory slot s. • The server support s two chann els with two DIM M slots per channel. o Memory channel 1 consists[...]

  • Page 39

    Remov al and replac emen t procedures 39 R emovin g a D IMM 1. Power do wn the server (on page 27 ). 2. Remove all po wer: a. Discon nect each po wer cord from the power sou rce. b. Discon nect each po wer cord from the server. 3. Unloc k the tower bezel (on page 26 ). 4. Remove the ac cess panel (" Access pan el " on page 31 ). 5. Remove[...]

  • Page 40

    Rem oval and repl acemen t procedures 40 c. Remove the heatsink from the processo r backplat e. To replace the component: 1. Clean t he old thermal grease from the processo r with the alcohol swab. A llow the alcohol to evaporate before continuing. 2. Remove the ther mal interf ace protec tive cover fro m the heatsink. CAUTION: Do no t overtighten [...]

  • Page 41

    Remov al and replac emen t procedures 41 c. Finish the install ation by complet ely tightening the sc rews in the same sequenc e. 4. Install the air baffle (" Air baffle " on page 32 ). 5. Install the access panel. 6. Lock th e tower bezel. 7. Conn ect each po wer cord to the server. 8. Conn ect each po wer cord to the power sou rce. 9. P[...]

  • Page 42

    Remov al and replac emen t procedures 42 5. Remove the air baffle (" Air baffle " on page 32 ). 6. Remove the heat sink (" Heat sink " on page 39 ). CAUTION: To avoid damage to the processor, do not touch the bottom of the processor, especially the contact area. CAUTION: The pi ns on the processo r socket are very fr agile. Any [...]

  • Page 43

    Remov al and replac emen t procedures 43 1. Install the processor. Use the notches on both sides of the processor to properly align it into the socket. CAUTION: Be sure t o close the processor soc ket retaining brack et before closin g the processor locking lever. The lever should close without resistance. Forcing the lev er closed can damage the p[...]

  • Page 44

    Remov al and replac emen t procedures 44 CAUTION: Do no t overtighten the screws a s this might damage the bo ard, co nnectors, or screws and voids the warranty of the board. 5. Install the heatsink: a. Position the heatsink using the guide pin on the processor backplate. b. Tighten one pair of diagonally opposite screws halfway, and then tighten t[...]

  • Page 45

    Remov al and replac emen t procedures 45 7. Remove the ex pansion slo t cover retai ner. 8. If removing a full - length expansion board, remove the board retainer securing it. 9. Remove the ex p ansion board. To replace th e compon ent, reverse the rem oval procedu re. Flash- backed write cache procedu res The following types of procedures are prov[...]

  • Page 46

    Remov al and replac emen t procedures 46 2. Remove all po wer: a. Discon nect each po wer cord from the power sou rce. b. Discon nect each po wer cord from the server. 3. Unloc k and open th e tower bezel (" Unloc k the tower bezel " o n page 26 ). 4. Remove the ac cess panel (" Access pan el " on page 31 ). 5. Remove the air ba[...]

  • Page 47

    Removal and replacemen t procedures 47 CAUTION: In systems that use externa l data storage, be sure that the server is the first unit to be powered down and the last t o be powered back u p. Taking this precauti on ensures that the system does not erro neously mar k the drives as failed when the ser ver is powered u p. To remove the c omponent: 1. [...]

  • Page 48

    Remov al and replac emen t procedures 48 8. Remove the capacitor pack. To replace th e compon ent, reverse the rem oval procedu re. R ecovering data from the flash - backed wr ite c ache If the server fail s, use the fo llowing proced ure to rec over data temporari ly stored in the FBWC . CAUTION: Before starting this procedure, read the informatio[...]

  • Page 49

    Remov al and replac emen t procedures 49 S ystem battery If the server no longer automatically displa ys the correct date and time, you might have to replace the battery that provides power to the real - time clock. Under normal use, battery life is 5 to 1 0 years. WARNING: The co mputer contains an internal lithium manganese dioxide, a vanadium pe[...]

  • Page 50

    Remov al and replac emen t procedures 50 R ear system fan To remove the c omponent: 1. Power do wn the server (on page 27 ). 2. Remove all po wer: a. Discon nect each po wer cord from the power sou rce. b. Discon nect each po wer cord from the server. 3. Unloc k the tower bezel (on page 26 ). 4. Remove the ac cess panel (" Access pan el "[...]

  • Page 51

    Remov al and replac emen t procedures 51 7. Remove the iLO module f rom the chassis. To replace th e compon ent, reverse the rem oval procedu re. E nablin g the dedi cated i LO m anagemen t port The onboard NIC 1/shared iLO conn ector is set as the default system iLO port. To enable the installed dedicated iLO module: 1. During th e server startup [...]

  • Page 52

    Remov al and replac emen t procedures 52 WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or power supply blank to cool before touching it. 5. Discon nect the power supply cables f rom the drive cage and the system board. 6. Remove the po wer supply. To replace th e compon ent, reverse the rem oval procedu re[...]

  • Page 53

    Remov al and replac emen t procedures 53 8. Remove the RPS backplane module. To replace th e compon ent, reverse the rem oval procedu re. R PS cage To remove the c omponent: 1. Power do wn the server (on page 27 ). 2. Remove all po wer: a. Discon nect each po wer cord from the power sou rce. b. Discon nect each po wer cord from the server. 3. Unloc[...]

  • Page 54

    Remov al and replacement procedures 54 11. Remove the po wer supply cage. To replace th e compon ent, reverse the rem oval procedu re. S ystem boar d CAUTION: To a void ESD da mage, when remo ving elect rostatic - sensitive com ponent s from the failed system board, place the components on a static - dissipating work surface or inside separate anti[...]

  • Page 55

    Remov al and replac emen t procedures 55 c. Remove the heatsink from the processor backplate. CAUTION: To avoid damage to the processor, do not touch the bottom of the processor, especially the contact area. 9. Open the processor locking lever, and then ope n the processor retaining bracket. 10. Grasp the processor by the edges, and then lift it ou[...]

  • Page 56

    Remov al and replac emen t procedures 56 b. Lift the system board out of the chassis. To replace th e system board : 1. Install the system board. 2. Connect all cables disconnected from the failed system board. 3. Install the DIMMs. 4. If removed, install the dedicated iLO management port. 5. Install the expansion boards. CAUTION: Failure to comple[...]

  • Page 57

    Remov al and replac emen t procedures 57 6. Open the processor locking lever, and then ope n the processor retaining bracket. 7. Remove the pro cessor soc ket c over. CAUTION: TH E PIN S O N TH E SYS TEM B OA RD ARE V ERY FRA GILE AND EAS ILY D AM AGED . To avoid damage to the system board: • Do not touch the processor socket contacts. • Do not[...]

  • Page 58

    Remov al and replac emen t procedures 58 8. Install the processor. Use the notches on b oth sides of t he processor to properly align it into the socket . CAUTION: Be sure t o close the processor soc ket retaining brack et before closin g the processor locking lever. The lever should close withou t resistanc e. Forc ing the lever clo sed can damage[...]

  • Page 59

    Remov al and replac emen t procedures 59 CAUTION: Do no t overtighten the screws a s this might damage the bo ard, co nnectors, or screws and voids the warranty of the board. 12. Install the heatsink: a. Position the heatsink using the guide pin on the processor backplate. b. Tighten one pair of diagonally opposite screws halfway, and then tighten [...]

  • Page 60

    Remov al and replac emen t procedures 60 19. Lock th e tower bezel. 20. Conn ect each po wer cord to the server. 21. Conn ect each po wer cord to the power sou rce. 22. Press the Power On/Standby button. The server exits stan dby mod e and applies fu ll power to the system. The system po wer LED changes from amber to green. After you replace the sy[...]

  • Page 61

    Troubleshooting 61 T r oubleshooting T roubleshooting resou rces The HP ProLiant Ge n8 Troubleshooting Guide, Volume I: Troubleshooting provides procedures fo r resolving common problems an d comprehen sive co urses of ac ti on for fau lt isolation and identification, issue resolu tion, and software m aintenanc e on ProLian t servers and server bla[...]

  • Page 62

    Dia gn ostic tools 62 D iagno sti c tools H P Insight Dia gnostics HP Insight Diagnostics is a proactive serv er management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabili ties to assist IT admin istrators who verify server installations, troubleshoot problems, and perform repair validatio[...]

  • Page 63

    Dia gn ostic tools 63 SAP Sol uti on Manager to manage their env ironment, HP recommends installing the latest HP Insight Remote Support Advanced software. This software provides comprehensive remote monitoring and proactive service support for nearly all H P servers, storage, network, and S AN environments, plus selected non - HP servers that have[...]

  • Page 64

    Dia gn ostic tools 64 U SB support and funct ionality US B sup port HP provides both standard USB 2.0 su pport and legacy U SB 2.0 support. Standard suppor t is provided by the OS through the appropriate USB device drivers. Before the OS loads, HP provides support fo r USB devices through legacy USB support, which is enabled by default in the syste[...]

  • Page 65

    Compone nt ident ificatio n 65 C omponent ide ntif icati on F ront pane l components Item Description 1 Optic al drive (option al) 2 Media driv e bay 3 USB conne ctors 4 Power O n/Stan dby button an d syst em power L ED 5 Drive bays (inside)[...]

  • Page 66

    Compone nt ident ificatio n 66 F ront panel LEDs and but tons Item Description Status 1 UID LED button Blue = Identification is activated Flashing blue = System is being managed remotely Off = Identif ication i s deact ivated 2 Health LED Green = Normal (system on) Flashing amber = System health is degraded Flashing red = System health is critical [...]

  • Page 67

    Compone nt ident ificatio n 67 R ear panel component s Item Description 1 Non - hot - plug power suppl y 2 Slot 4 PCI e x16 (8, 4, 1) * 3 Slot 3 PCI e x8 (8, 4, 1)* 4 Slot 2 PCI e x8 (4, 1)* 5 Slot 1 PCI e x4 (1)* 6 Expansion slot c over retaine r 7 Serial conn ector 8 Video conn ector 9 Dedic ated iLO m anagem ent port ( option al) 10 NIC 1/shared[...]

  • Page 68

    Compone nt ident ificatio n 68 R ear pane l LEDs an d button s Item Description Status 1 NIC link L ED G reen = Link exists Off = No li nk exists 2 NIC status LED Green = A ctivity exists Flashing green = Activity exists Off = No activity exists 3 UID LED b utton Blue = Identificati on is activated Flashing blue = System is being manag ed remote ly[...]

  • Page 69

    Compone nt ident ificatio n 69 S ystem bo ard components Item Description 1 RPS connecto r 2 Processor soc ket 3 System battery 4 24 - pin powe r supply con nector 5 Mini- SAS connector 6 SATA connectors 7 Internal USB cable connector 8 Interna l USB co nnecto r 9 SD card sl ot 10 Front USB con nector 2 11 Front USB con nector 1 12 Front panel LED [...]

  • Page 70

    Compone nt ident ificatio n 70 * For more i nformation o n the expansion slot specif icatio ns, see " PCIe expansion slot definitions (on page 70 )." DIMM sl ot lo cations DIMM slots are numbered sequentially (1 through 4 ) for the processor. The supporte d AMP modes use the letter assignment s for popu lation gu idelines. P CIe ex pans i[...]

  • Page 71

    Compone nt ident ificatio n 71 Switch Default Funct ion 2 Off Off = System configurat ion can be changed On = System configuration is locked 5 Off Off = Po wer - o n passw ord is en abled On = Powe r - on passwo rd is dis abled 6 Off Off = No funct ion On = R OM reads c onfigurat ion as invalid 3, 4, 7, 8, 9, 10, 11, 12 — Reserved When the system[...]

  • Page 72

    Compone nt ident ificatio n 72 D rive numbering • Four - bay LFF drive model • Eight - ba y SFF drive model[...]

  • Page 73

    Compone nt ident ificatio n 73 D rive LED de finitions Item LED Status Definition 1 Locate Soli d blue Th e drive is bei ng iden tified by a h ost applic ation . Fl ashing blue The dri ve car rier firmware is being updated or requi res an upda te. 2 Activity ring Rotating green Drive activ ity Off No drive activity 3 Do not remov e Solid white Do n[...]

  • Page 74

    Compone nt ident ificatio n 74 F BWC module LED def initions The FBWC module has three single - color LEDs (one amber and two green). The LEDs are duplicated on the reverse side of the cach e module to facili tate status viewin g. 1 - Amber 2 - Green 3 - Green Int erp reta tion Off Off Off The cache module is not powered. Off Flashing 0.5 H z Flash[...]

  • Page 75

    Compone nt ident ificatio n 75 F an locatio ns Item Description 1 Rear system fan (f an 1, for processor c ooling) 2 Front system fan (fan 2, for e xpansion board coolin g) T- 10/T - 15 T orx s cre wdri ver The server inclu des a T - 10/ T - 15 Torx screw driver loc ated on the side o f the media drive ca ge. Use the screwdriver to l oosen screws d[...]

  • Page 76

    Cablin g 76 C abling C abling over view Thi s section provides guidelines that help you make informed decisions about c abling the server and hardware options to optimize performance. For information on cabling p eripheral components, refer to the white paper on high - density deployment at the HP websi te ( http: //www.hp.co m/products/servers/pla[...]

  • Page 77

    Cablin g 77 S ystem fan cabling Item Description 1 Rear syst em fan cable 2 Front s ystem f an cable S torag e cabling F our - bay LFF dr ive c abling N on - hot - plu g, SAT A driv e su pport only[...]

  • Page 78

    Cablin g 78 Item Description 1 Power c able 2 Data cable N on - hot - plu g, SAT A an d SAS drive support Item Description 1 Power c able 2 Data cable H ot - plu g, SATA dr ive sup port Item Description 1 Power c able[...]

  • Page 79

    Cablin g 79 Item Description 2 Mini- SAS cable H ot -plug, SATA and SAS d rive s upport Item Description 1 Power c able 2 Mini- SAS cable E ight - bay SFF dr ive cabli ng This drive configuration supports hot - plug SATA a nd SA S dri ves. Item Description 1 Power c able[...]

  • Page 80

    Cablin g 80 Item Description 2 Mini- SAS cable 3 Mini- SAS cable M edia drive cabli ng • Media drives in a nonredundant power configuration Item Description 1 Upper medi a drive pow er ca ble 2 Lower me dia drive SATA cabl e 3 Upper medi a drive S ATA cable 4 Lower me dia drive power cabl e[...]

  • Page 81

    Cablin g 81 • Media drive in a redundant power configuration Item Description 1 Upper medi a drive S ATA cable 2 Upper medi a drive pow er ca ble P ower supply c abling N onr edundant po wer su pply cabl ing Item Description 1 24 - pin powe r supply c able 2 4- pin powe r supply ca ble[...]

  • Page 82

    Cablin g 82 R edundan t pow er supply c abli ng Item Description 1 24 - pin powe r supply c able 2 26 - pin RP S cable 3 4- pin power supply cable (with the 8 - pin to 4 - pin adapt er cable con nec ted) C apacitor pack cabling[...]

  • Page 83

    Specifica tions 83 S pec if icati on s E nvironment al specifi cations Specification Val ue Tempera ture ra nge* Operati ng 10 ° C to 35 ° C ( 50 ° F to 95 ° F) Nonoperatin g - 30 ° C to 60 ° C ( - 22 ° F to 140 ° F) Relativ e humidity (nonco ndensi ng) Opera ting, maximu m wet bu lb temperature of 28°C (82.4°F ) 10% to 90% Nonoper ating,[...]

  • Page 84

    Specifica tions 84 H P 350 W 4U F actor y Int egrat ed Pow er S upply Specification Val ue Input r equi rements — Rated in put voltag e 100 V AC to 240 V AC Rated in put freque ncy 47 Hz to 63 Hz Rated in put curren t 6 A Rated in put power 440 W at 1 00 V AC input 440 W at 200 V AC input Efficien cy No less than 82% at 100% load No less t han 85[...]

  • Page 85

    Support and othe r resources 85 S upport an d other r es our ces B efore you contact HP Be sure to have the following information av ailable before you call HP: • Active Health S ystem log Download and have available an Active Health System log for 3 days before the failure was de tected. For more info rmation, see the HP iLO 4 U ser Guide or HP [...]

  • Page 86

    Acronyms and abbrevi ation s 86 A c r on y ms an d abbr e v iati ons ABEND abnormal end AMP Advanced Memory Protection ASR Automati c Server Recover y CSR Customer Self Repair DDR double data rate FBWC flash - backed write cache HP CS HP Common Slot (power supply) HP SIM HP Systems Insight Manage r iLO Integrated Lights - Out IML Integrated Managem[...]

  • Page 87

    Acronyms and abbrevi ation s 87 NMI nonmaskable interrupt NVRAM nonvolatile memory PCIe peripheral component interconnect express POST Power - On Self Test RBSU ROM- Based Setup Utility RDIMM registered dual in - line memory module RPS redundant power supply SAS serial attached SCSI SATA serial ATA SD Secure Digital SFF small form factor SLC single[...]

  • Page 88

    Acronyms and abbrevi ation s 88 UDI MM unregistered du al in - line memory module UID unit identification USB universal serial bus[...]

  • Page 89

    Docume ntation feedbac k 89 Doc umentatio n feedbac k HP is committed to providing documentation that meets your needs. To help us impr ove the documentation, send any errors, suggestion s, or c omments to Documentation Feedback ( mailto:doc sfeedback @hp.co m ). Include the document title and pa rt number, version number, or the URL when s ubmitti[...]

  • Page 90

    Index 90 A access panel 31 air baffle 31 ASR (Au tom atic Server Reco ver y) 64 authori zed reseller 85 Auto mati c Ser ver Rec over y (ASR ) 64 B bezel, tower 26 blanks 27 board components 69 buttons 65 C cables 76 cabling 76, 77, 78, 79, 80, 81, 82 cache mod ule 45 cache module, removing 45 capacitor pack 45, 46, 82 components 16, 19, 24, 60, 65 [...]

  • Page 91

    Index 91 LEDs, rear pan el 68 LEDs, SAS hard drive 73 LEDs, trou bleshooti ng 61 LEDs, unit identification (UID) 66 M management tools 62 mechanical components 16 media drive bay cabling 80 N NMI header 71 O optical drive 32, 65 P part numbers 16 PCI expansion slots 70 phone numbers 85 power down pro cedure 27 power requi rements 84 power supply 30[...]