English dropdown-ico

Hobart ML-104586 manual

1
2
3
4
5
6
7
8
9
10
11
12

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Hobart ML-104586, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Hobart ML-104586 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Hobart ML-104586. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Hobart ML-104586 should contain:
- informations concerning technical data of Hobart ML-104586
- name of the manufacturer and a year of construction of the Hobart ML-104586 item
- rules of operation, control and maintenance of the Hobart ML-104586 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Hobart ML-104586 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Hobart ML-104586, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Hobart service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Hobart ML-104586.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Hobart ML-104586 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    FP350 FOOD PROCESSOR MODEL FP350 ML-104586 FOOD PROCESSORS 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 19353 Rev. D (Oct. 2000)[...]

  • Page 2

    – 2 – © HOBART CORPORATION, 1995 T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Page 3

    – 3 – Installation, Operation, and Care of MODEL FP350 FOOD PROCESSOR SA VE THESE INSTRUCTIONS GENERAL The FP350 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits, or cheese. A worktable, a wall rack, and a wide range of slicer, shredder, and dicing plates are available options. INST ALLA TIO[...]

  • Page 4

    – 4 – Fig. 1[...]

  • Page 5

    – 5 – OPERA TION WARNING : ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT . Proper assembly of the FP350, including selection of the appropriate cutters, is necessary for correct operation of the food processor. Refer to the Cutting Tool Guide for sizes of cutters and refer to the appropriate operation instructions. CONTROLS (F[...]

  • Page 6

    – 6 – 3. To remove the pusher plate, hold the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 4. Take hold of the pusher plate with both hands (Fig. 2). 5. Rotate pusher plate until the pin on the shaft is out of the slot on the bracket. Pull the pusher plate up and[...]

  • Page 7

    – 7 – Removing the Cutting Tools 1. Using the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 2. Turn the lock handle counterclockwise and swing the feed cylinder out to the right. 3. Using the wrench supplied, loosen the decoring screw in a clockwise direction. 4. [...]

  • Page 8

    – 8 – CLEANING WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine and wash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft clean cloth. Allowing food juices to dry on the machine may cause discolor[...]

  • Page 9

    – 9 – CUTTING TOOL GUIDE Fractional sizes are in inches (millimeters are in parentheses). Slicers Use Fine and Standard Slicers for sliced products and for dicing. Soft products like tomato - use the FINE SLICER, not the STANDARD SLICER. FINE SLICER 1 ⁄ 16 (1.5 mm) FINE SLICER 1 ⁄ 8 (3 mm) FINE SLICER 5 ⁄ 32 (4 mm) FINE SLICER 7 ⁄ 32 (6[...]

  • Page 10

    – 10 – Dicer and French Fry Plates The recommended slicer plate will produce near cube-shaped products. The DICER grid dimension must be equal to or larger than the SLICER dimension. DICER 9 ⁄ 32 (7.5 mm) Use with FINE SLICER 7 / 32 (6 mm), 5 ⁄ 32 (4 mm), 1 ⁄ 8 (3 mm), 1 ⁄ 16 (1.5 mm) * DICER 3 ⁄ 8 (10 mm) Use with STANDARD SLICER 3 /[...]

  • Page 11

    – 11 – MAINTENANCE WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to make sure that it is in proper working order. Plates must be clean, intact and sharp. The knife shaft should be regularly lubricated with a drop of mineral oil, NOT COOKING OIL. REPLACEMENT DICING GRIDS[...]

  • Page 12

    – 12 – FORM 19353 Rev. D (Oct. 2000) PRINTED IN U.S.A. SERVICE Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment. Long-term service contracts are available on this and other Hobart products. SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION Low output or bad cutting results. A. B. C. D. E. Wrong cutting tool[...]