Hasbro PUB 0804 manual
- Read online or download the manual
- 18 pages
- 1.62 mb
Go to page of
Similar user manuals
Hasbro PN 70595700002 pages 1.06 mb
Hasbro Transformers Universe 27271 Asst.1 pages 1.03 mb
Hasbro Star Wars Revenge of the Sith Crab Droid 855711 pages 0.22 mb
Hasbro 809451 pages 2.46 mb
Hasbro Games2 pages 0.32 mb
Motorized Toy Car
Hasbro 834601 pages 1.44 mb
Hasbro I Dog Ampd16 pages 1.61 mb
Hasbro 81060 Asst.1 pages 2.03 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Hasbro PUB 0804, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Hasbro PUB 0804 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Hasbro PUB 0804. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Hasbro PUB 0804 should contain:
- informations concerning technical data of Hasbro PUB 0804
- name of the manufacturer and a year of construction of the Hasbro PUB 0804 item
- rules of operation, control and maintenance of the Hasbro PUB 0804 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Hasbro PUB 0804 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Hasbro PUB 0804, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Hasbro service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Hasbro PUB 0804.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Hasbro PUB 0804 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
1 Illuminator Glider Door Installation Manual Ultimate Products Inc. • 2319 Laurelbrook Street• Raleigh, NC 27604 • (800) 542 - 7221 • Fax (919) 834 - 4526 PUB 0804[...]
2 Tools required for Installation Items needed but not included: Screws for mounting track assembly. Impact Wrench Electric or cordless drill Set of drill bits 1/4” to 9/16” Set of box - end wrenches 1/4” to 9/16” Set of sockets with 3/8” drive, 1/4” to 9/16” Hammer drill with 3/8” masonry bit if mounting track to concrete block wal[...]
3 Parts Identification GLP2003 - Glider Pulley with Bolt and Nut CV100: Cam Valve QD100: Quick Exhaust Valve AP1078: Male Tube Stem AP1075: 3/8" x 1/4" Reducing elbow quick connect AP1080: 3/8” x 1/4” male quick connect AP1050: Turnbuckle GB2003A: Bracket ‘A’ GB2003B: Bracket ‘B’ B A[...]
4 Parts Identification Continued E - 1 E - 2 A - 1 A - 2 B - 2 B - 1 C - 2 C - 1 D - 2 D - 1 C - 1: Left Hand Slotted Glider Stop C - 2: Right Hand Slotted Glider Stop B - 1: Left Hand Glider Stop B - 2: Right Hand Glider Stop A - 1: Left Hand Glider Guide A - 2: Right Hand Glider Guide D - 1: Left Hand Slotted Glider Stop D - 2: Right Hand Slotted[...]
5 Insure that Walls on each side of door opening are clear of all obstructions (Door will protrude 5 1/2” Into building) Install bottom of door track 1” above door opening Door Opening 1” A 1 2 Above the left hand side of door opening install track w/ operator As shown in Figure B Place the bottom of track on line that was drawn 1” above op[...]
6 Panel #1 Panel #2 Panel #3 Panel #4 Panel Identification: Install all panels w/ center Brace on inside of building[...]
7 Slide Panel #1 & 2 (see page 4) Into track #1 As shown in figure C and step number 6 below. Make sure center brace is on the inside of building 5 C Slide Panel #4 (Clear Section) Into track #2 As shown in figure D *Rubber astragal is on the right side of door panel Track #1 Track #2 D 7 Slide Panel #3 (Clear Section) Into track #2 As shown in[...]
8 9 Slide panels #2 and #3 to the right hand side of track - The track that does not have the operator Place all panels as shown on page 4 so the door is in the closed position 10 Preparing to install Glider blocks and Guides A - 1 A - 2 B - 2 C - 2 B - 1 C - 1 D - 2 D - 1 E - 1 E - 2 See the following pages for installation of these parts[...]
9 11 Install Blocks on Door Sections Panel #2 Panel #4 B - 1 C - 1 D - 1 Install Items ‘B - 1,C - 1, and ‘D - 1’ on Panel #2 and Panel #4 as shown Install Items ‘B - 2’, ‘C - 2’ and ‘D - 2’ on Panel #1 With Door Sections in Closed position:[...]
10 12 Install Items ‘A - 1’and‘A - 2’ Panel #2 Panel #4 A - 1 With Door Sections in Closed position: Install item ‘A - 1’ on Panel #2. The guide bar is inserted into slot of A - 1 as shown A - 1 **IMPORTANT - MAKE SURE DOOR IS COMPLETELY CLOSED AS SHOWN ON PAGE 4 Follow same steps when installing item ‘A - 2’ on Panel #1 (no picture[...]
11 13 Install Items ‘E - 1’and ‘E - 2’ Keeping Door in Closed Position: Insert item ‘E - 1’ onto guide bar of panel #2 and attach to wall with screws. (screws not provided) Panel #2 Panel #4 Install Item ‘E - 2’ on Panel #1 as shown in step number 13 above E - 1 E - 1 14 15 Close panels to meet in the center Preparing to install Doo[...]
12 16 Install Bracket ‘A’ Slide Bracket ‘A’ onto operator rod and position bracket ‘A’ 3” from edge of door as shown on step #17. Now attach aluminum block to operator rod as shown 17 A B A 3” 3” *Important: Push Operator Rod fully into cylinder. Now pull operator rod out of cylinder 1/4” Install Door Cables 18 Pre Drill holes f[...]
13 Air Powered Operator Track 33” minimum 33” minimum 8 1/4” Door Opening Door Opening 20 Run cable around top of pulley on right side of track and through top slot of aluminum block on bracket ‘B’ (do not tighten block until later) 19 Run cable through top slot of bracket ‘A’: A Tighten bolts of aluminum block down onto cable. H 21 C[...]
14 22 Install brush on bottom of door sections Install brush on bottom of each panel so that brush angles in- ward as shown. (Brushes will angle toward each other) Bottom of brush should touch floor for a proper seal.[...]
15 23 Install floor guides J K Space Items ‘J’ & ‘K’ 2 1/4” apart Make sure center of floor guides are in center of door opening Place item ‘J’ even w/ door opening 24 Install Air Fittings Figure 1 Figure 2 Figure 3 Install fittings to Figure 1 & 2 Install fitting to Figure 3 and here[...]
16 Left side of operator (inside looking at door) Right side of operator (inside looking at door) A A B C D H G F E J I B D Connect Air line from “A” (left side of operator) to “F” Connect Air line from “H” to “C” Connect Air line from “B” (right side of operator) to “E” Connect Air line from “G” to “D” Connect air l[...]
18 Door opening requirements for Glider Door For 10’ opening — Minimum of 33” of side room on each side Operator will open the door 9’9” wide leaving 1 1/2” of door in opening Make Floor level! Track and operator weight approx. 155 pounds. Track w/ operator extends 8 1/2” above door opening. Track is fastened to wall w/ self tapping s[...]