English dropdown-ico

Graco Ultra Max 309273 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Graco Ultra Max 309273, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Graco Ultra Max 309273 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Graco Ultra Max 309273. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Graco Ultra Max 309273 should contain:
- informations concerning technical data of Graco Ultra Max 309273
- name of the manufacturer and a year of construction of the Graco Ultra Max 309273 item
- rules of operation, control and maintenance of the Graco Ultra Max 309273 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Graco Ultra Max 309273 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Graco Ultra Max 309273, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Graco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Graco Ultra Max 309273.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Graco Ultra Max 309273 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Ultra Max t Electric Airless Sprayers Operating Instructions The intent of these instructions is to provide the new painter with a quick and easy reference to become familiar with airless sprayers. This does not replace the Instruction Manual supplied with this sprayer . Read and understand the instructions and warnings in that manual. Important No[...]

  • Page 2

    2 309273 PRESSURE RELIEF – Do this when cleaning, repairing or shuting down sprayer WASTE RESÍDUOS À JETER DESECHO 1. T urn pressure to lowest setting. T urn power OFF . Unplug sprayer . 2. T rigger gun to relieve pressure. 3. Put drain tube in pail . T urn prime valve down. W ARNING Fire and explosion hazard: Solv ent and pa i nt f um es c an [...]

  • Page 3

    3 309273 Power Switch Pressure Control Component Identification Suction T ube Filter Prime V alve Prime/drain position Paint position Spray Gun T rigger Safety Put trigger safety ON when not spraying. T ake trigger safety OFF before triggering gun. Digital Display (Not available on all models) 15/20A Switch AutoClean V alve (Not available on all mo[...]

  • Page 4

    4 309273 1. Connect Graco airless hose to sprayer . T ighten securely . 2. Connect other end of hose to gun. Setup 3. T ighten securely . 4. Remove tip guard.[...]

  • Page 5

    5 309273 5. Check inlet strainer for clogs and debris. 6. Fill throat packing nut with TSL to prevent premature packing wear . Do this each time you spray . Approximate Fill Level[...]

  • Page 6

    6 309273 P AINT FLUSH 7. T urn power OFF . 8. Plug power supply cord into a properly grounded electrical outlet. 9. T urn prime valve down. 10. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. Do 1 . – 5 . of Startup to flush out storage oil shipped[...]

  • Page 7

    7 309273 FLUSH Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks occur , do Pressure Relief . T ighten leaky fittings. Repeat Startup, 1. – 5 . If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6. Startup 15 SEC 1. T urn prime valve down. T urn pressure control to lowest pressu[...]

  • Page 8

    8 309273 FLUSH P AINT General Surfaces T ip Recommendations Chart Wood Interi or C ab- inets , Paneling Interior Walls or Ceilings Dry wall, Plaster Ov er Hang Su rfaces Materi als Filter Mesh 6–8 8–10 10–12 12–14 Orific e Size (in. ) Fan Widt h ( in.) at 12 in . Masonr y Bl ock, Stu cco, Co ncre te Wood Ex terior Shingle, Siding, Shiplap O[...]

  • Page 9

    9 309273 SwitchTip and Guard Assembly 1. Insert SwitchT ip. Insert seat and OneSeal. 2. Screw assembly onto gun. Hand tighten. SwitchT ip OneSeal seat Press SMARTCONTROL button to cycle through PRESSURE – GAL/L TR – TIMER displays D PRESSURE : Fluid pressure at the sprayer D GAL/L TR : Accumulated total of gallons/liters sprayed D TIMER : Durat[...]

  • Page 10

    10 309273 Spray T est Pattern heavy edges Clearing Tip Clogs 1. T rigger gun and spray test pattern. Slowly adjust pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular , 10–12 in. (25–30 cm) from surface. Spray back and forth. Use strokes overlapped by 50%. Start[...]

  • Page 11

    11 309273 Cleanup P AINT 1. T urn power OFF . 2. T urn pressure to lowest setting. T rigger gun to relieve pressure. 3. T urn prime valve down. 4. Remove filter assembly and assemble gun without filter . Perform AutoClean procedure (Manual 309278) or follow conventional flushing/cleaning procedure that follows: ti2874a Contractor Contractor II[...]

  • Page 12

    12 309273 5. Remove guard and SwitchT ip. 6. Clean filter , guard and SwitchT ip in flushing fluid. P AINT FLUSH 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint. 8. If sprayer has a filter , unscrew bowl, remove filter . Assemble without filter . Clean filter . [...]

  • Page 13

    13 309273 P AINT FLUSH 9. T urn power ON. 10. T urn prime valve hori- zontal. 1 1. Hold gun against paint pail. T ake trigger safety OFF . T rigger gun until flushing fluid appears. 12. Move gun to flushing pail, hold gun against pail, trigger gun to thoroughly flush system. Release trigger and put trigger safety ON. 13. T urn prime valve down and [...]

  • Page 14

    14 309273 P AINT FLUSH FLUSH 14. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid. T urn power OFF . 15. Make sure plastic center tube is tightened securely . Install filter bowl and filter . Hand tighten filter bowl. Install filter assembly into gun. Hand tighten gun handle. 16. Wipe sprayer , hose and gun[...]

  • Page 15

    15 309273 T rouble Shooting TYPE OF PROBLEM WHA T TO CHECK If check is OK, go to next check WHA T TO D O When check is not OK refer to this column D Sprayer does not respond 1. Check if error code is displayed, page 9. 1. Refer to your repair manual. D Sprayer will not prime or takes too long to prime 1 . Air in paint pump 1. Open prime valve to pu[...]

  • Page 16

    16 309273 Daily: Inspect, clean and replace as needed D Manifold filter , gun filter and inlet stainer D W et cup for leakage, tighten if needed D TSL level D Gun trigger safety D T ip wear , replace if necessary D Electric cord and plug W eekly: D Check tightness of wet cup. D Inspect all high pressure paint hoses. Annually: D Schedule maintenance[...]