Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Graco LC-1000, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Graco LC-1000 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Graco LC-1000. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Graco LC-1000 should contain:
- informations concerning technical data of Graco LC-1000
- name of the manufacturer and a year of construction of the Graco LC-1000 item
- rules of operation, control and maintenance of the Graco LC-1000 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Graco LC-1000 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Graco LC-1000, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Graco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Graco LC-1000.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Graco LC-1000 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
The T rabon microprocessor based LC-1000 Controller is a multi-use solid state controller that is dedicated to the operation and monitoring of intermittent operat- ing series and parallel centralized lubrication systems equipped with a cycle or pressure switch for cycle completion feed back. The LC-1000 monitors and schedules lubrication inter- val[...]
-
Page 2
Page 2 14540 LC-1000 Lube System Controller INPUT VOL T AGE HOT NEU PUMP PUMP 12 3 4 5 6 7 8 9 MANUAL RUN 10 1 1 12 13 14 15 16 17 18 19 CYCLE SWITCH (SEE NOTE 2) + - + - F AUL T F AUL T DO NOT USE OPTIONAL LOW-LEVEL SWITCH AND/OR HIGH PRESSURE SWITCH. BOTH MUST BE OPEN DURING NORMAL SYSTEM OPERA TION. FIG 1 Option for units built af ter February 1[...]
-
Page 3
Page 3 14540 LC-1000 Lube System Controller 76.2 (3.00) DIMENSIONS mm / (Inches) 1 14.3 (4.50) 127.0 (5.00) 1 14.3 (4.50) 4.8 (.19) POWER LUBE F AUL T CYCLE LUBE SYSTEM CONTROLLER TIME COUNTS REMAINING MANUAL RUN PRGM ENTER MODEL LC-1000 MANUAL RUN BUTTON 127.0 (5.00) ORDERING INFORMA TION PROGRAMMING INSTRUCTIONS The LC-1000 Controller has icons i[...]
-
Page 4
Page 4 14540 LC-1000 Lube System Controller OPERA TION When power is applied, the green “POWER LED”lights and the LC-1000 counts down alternately from the programmed “OFF/ON” T imes/Counts to zero. In the “ON” (Monitor) mode, the ” PUMP LED” lights. The pump is activated and both the “ON and “RUN” icons are displayed. If the p[...]
-
Page 5
Page 5 14540 LC-1000 Lube System Controller Sample LC-1000 Program for Series Progressive, 31 Point Series Progressive System 4. “CYCLE” (Cycle Switch T ransitions) a) Press “ENTER” Key; CYCLE (switch transitions) blinks b) Use S Key and X Key to select 20 (20 cycle switch transitions = 10 Divider cycles) c) Press “ENTER” Key to accept [...]
-
Page 6
Page 6 14540 LC-1000 Lube System Controller Sample LC-1000 Program for Piston Distributor or Injector Systems 31 Point Piston Distributor System DESCRIPTION System Lube V olume: 99 cc (6.0 cu in) per hour EO-3 Motor Driven Pump: 140 cc/min (8.5 cu in) T otal Piston Distributor Displacement: 4.62 cc/cycle (.28 cu in) Cycle Interval: 99 cc / 4.62 cc [...]
-
Page 7
Page 7 14540 LC-1000 Lube System Controller Sample LC-1000 Program for Bi-Flo (Dual Line) Systems 31 Point Bi-Flo (Dual Line) System DESCRIPTION System Lube V olume: 6.0 cu in (99 cc) per hour Bi-Flo Motor Driven Pump Used: 8.6 cu in (141 cc) per minute. Note 1: Requires a Motor Starter Note 2: Requires a hydraulic reverser with cycle switch. Cycle[...]
-
Page 8
Y our Program Record Company: _____________________________________ By: _______________________ Machine Identi fi cation: __________________ Date: _____________________ System T ype: Bi-Flo ___ Piston Distributor ___ Series ___ Other: _________________ On (Monitor) V alue: T ime/Count _____ Seconds ___ Minutes ____Hours ___ Counts _____ Off V alue[...]