English dropdown-ico

Graco 312350E manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Graco 312350E, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Graco 312350E one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Graco 312350E. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Graco 312350E should contain:
- informations concerning technical data of Graco 312350E
- name of the manufacturer and a year of construction of the Graco 312350E item
- rules of operation, control and maintenance of the Graco 312350E item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Graco 312350E alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Graco 312350E, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Graco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Graco 312350E.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Graco 312350E item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    312350E Instr uctions , Repair and P ar ts Dyna-Star ® HYDRA ULIC RECIPROCA T OR AND PUMP - For lubricating fluids onl y - 10:1 Ratio Universal Pump and Recipr ocator 600 psi (4.1 MP a, 41 bar) Maximum Hydr aulic Input Pressure 7500 psi (51 MP a, 517 bar) Maximum Fluid Outlet Pressure Model 247540: Pump, 60 lb A u tomatic Lube Pu mp Module Length [...]

  • Page 2

    Warnings 2 312350E Wa r n i n g s The f ollowing w arnings are for the set up , use, groun ding, maintenance , and repair of this equipment. The e xclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure-specif ic risk. Refer back to these wa r nings. Add itional, product- specific warnings ma y be fou n[...]

  • Page 3

    Warnings 312350E 3 MO VING P ARTS HAZARD Movin g par ts can pinch or amputate fingers and other bod y par ts. • K eep clear of mo ving par ts. • Do not op erate equipme nt with prot ective guards or covers remov ed. • Pressurized equipmen t can star t without warning. Bef ore chec king, mo ving, or ser vicing equipment, f ollow the Pressure R[...]

  • Page 4

    Installation 4 312350E Installation Key: A F ollower plate B W eep tube C Fluid outlet line (to gun) D Drain v alve (required) E Ground wire F Hydraulic retur n line, minimum 3/4 inch I.D . (required) G Hydraulic outlet, 3/4” npt (f) H Retur n line shut-off valv e, minimum 3/4 inch (required) J Hydraulic inlet, 3/4” npt (m) K T ee, 3/4” npt L[...]

  • Page 5

    Installation 312350E 5 Pump Accessories Follo wer Plate (A): ensures a good prim e. Place f ollower plate on grease and rota te while press ing fir mly to le v el material. Order par t nu mber 247700 f or 60# and 90# automatic lube pump modules; 247701 f or 120# refinery reser voir; or 247702 f or 400# refiner y reservoir . Pump Outlet Drain V alve[...]

  • Page 6

    Installation 6 312350E Gr ounding T o reduce the risk of static sparking, ground pump . Check yo ur loc al electric al code for detailed grounding instructions f or yo ur area and type of equipment. • Pump: Use g round wire and clamp as shown in F IG . 3. Order Groun ding Wire and Clamp Kit, P ar t No . 222 011. • Hydraulic Hoses and Fl uid Out[...]

  • Page 7

    Operation 312350E 7 Operation Pressure Relief Pr ocedure The system pressure m ust be manually relie v ed to pre v ent the system from starting or dispensing accidentally . Follo w this pressure relief procedure whenev er you are instructe d to: • reliev e pressure. • check or service any system equipment. • install or c lean nozzle. F or the[...]

  • Page 8

    Operation 8 312350E Star ting Pump 1. T ur n on hydr aulic pow er supply . 2. Open retu rn line shut-off valv e (H) first, then slowly open the h ydraulic supply sh ut-off v alve ( L). 3. Adjust flow contr ol valv e (Q) to limit the h ydraulic flow to no more t han 3 gpm ( 11 lpm), which is appro ximately 60 cycles per minute . 4. Adjust pressure r[...]

  • Page 9

    Troubleshooting 312350E 9 T r oubleshooting Prob lem Cause Solution Pump does not run. Closed dispense v alv e. Pump only runs with v alve op en. Pressure too low . Increase supply pressure using a pressure adjusting v alv e. Insufficient h ydraulic fl uid supp ly . Check h ydraulic supply . Adjust to a maximum of 3 gpm (11 lpm) flow . Clogged flu [...]

  • Page 10

    Service 10 312350E Service Replacing Thr oat Seals See F IG . 5. 1. Relieve pressure , page 7. 2. Disconnect reciprocator from pump . 3. Remov e f our ca pscrews ( 15) from bottom of adapter (43). T ap adapter to loosen it an d pull it off the bot- tom cap (32). 4. Remove seal (44, include d in Reciproc ator Repair Kit 247455) fro m top of adapter [...]

  • Page 11

    Service 312350E 11 Disconnecting Recipr ocator and Displacement Pump See F IG . 6 and Displacement Pump P ar ts, page 18. F IG . 6 1. Flush pump if possib le and stop it with displacement rod in low est position. 2. Relieve pressure , page 7. 3. Disconnect outle t hose from displacement pump . 4. Slowly loose n hydr aulic supply (60) and return (5)[...]

  • Page 12

    Reciprocator Repair 12 312350E Recipr ocator Repair See F IG . 7 and F IG . 9 and Reciprocator P arts, page 18. Drain Oil Out of Reciprocator Bef ore y ou begin, dr ain oil out of r eciprocator . 1. Relieve pressure , page 7. 2. Place reciprocator in a dr ain pan. F IG . 7 See F IG . 7 f or steps 1-3, e xcept wher e noted. 1. Place adapter (43) in [...]

  • Page 13

    Reciprocator Repair 312350E 13 F IG . 8 See F IG . 8 and Recipro cator P ar ts pa ge 18 f or steps 4-20, except where noted. 4. T ap bottom of di splacement rod (3 4) with a plastic mallet to loosen cylinder (25). 5. Grasp v alv e spool (31) and pull it off cylinder and tie rods (38). Pull cyli nder and piston off bottom cap (32). It is not nece ss[...]

  • Page 14

    Reciprocator Repair 14 312350E 10. Clean all sealant from thread s of any par t you ar e reusing. Apply Loctite ® 242 or P erm a-Loc ® 115 thread seala nt to first two or thre e inter nal thre ads of valv e assembly (31). If yo u remov ed capscre w (51) apply thread sea lant to first two or three inter nal threads of v alve stop (26). Apply pr im[...]

  • Page 15

    Reciprocator Repair 312350E 15 F IG . 11 See F IG . 11 f or steps 17- 24 e xcept where noted. 17. Place adapter (43) in a vise. Install seal s as described on page 10. Install cylinder cap (3 2). 18. If tie rods (38) were remov ed, re install them with shor t threaded end up . The other end should be screw ed about 9/16” into bo ttom cylinder cap[...]

  • Page 16

    Displacement Pump Repair 16 312350E Displacement Pump Repair Disassembl y See F IG . 13 f or steps 1-10, e xcept where note d. 1. If possible, flush pump . Relieve pressu re , page 7 . 2. Follo w instr uction for Disconnecting t he Recipr o- cator and Displacement Pump , page 11. 3. Clamp pump in vise. 4. Use strap wr ench to scre w shov el tube (1[...]

  • Page 17

    Displacement Pump Repair 312350E 17 F IG . 13 117 116 108 113 111 † 112 † 109 102 106 † 104 † 103 110 † 106 † 114 107 Assembled / Cuta way Vie w Using nut (113), torque the pump cylinder 109 to the extension tube (114) at 45 to 55 ft-lb (61 to 75 N.m). 1 T orque the shovel rod (108) to the piston (102) at 25 to 30 ft-lb (34 to 41 N.m). [...]

  • Page 18

    Reciprocator Parts 18 312350E Recipr ocator P ar ts 36 37 3 39 2 30 60 4 5 61 66 60a 5a 45 29 9 7 6 51 12 1 13 25 40 13 14 32 34 38 18 20 21 20 23 17 49 22 24 58 26 1a 43 16 35 44 8 28 27 15 46 52 11 19 31 4 5 3 6 5 5 1 6 6 2 T orque to 170-180 in-lbs (19-20 N.m) 1 T orque to 42-45 in-lbs (4-5 N.m). 2 T orque to 54-56 ft- lbs (73-76 N.m). 3 T orqu [...]

  • Page 19

    Reciprocator Parts 312350E 19 Reciprocator P arts ▲ Replacement Danger and Warning labels, tags, and cards are av ailable at no cost. * These par ts and items 202 on page 20 are included in Kit 247455 (purchase sepa rately). † These parts are inclu ded in Kit 241623 (purchase sepa- rate ly ). Assembl y T ool 189305 required f or repair ing the [...]

  • Page 20

    Pump Parts 20 312350E Pump P ar ts Model 247540 60# A utomatic Lube Pump Module Length Model 247443 120# Drum Lengt h Model 247450 400# Drum Lengt h ▲ Replacement Danger an d W ar ning labels , tags, and cards are av ailab le at no cost. * These par ts are included in Kit 247455 (pur chase separate ly). See page 18 f or other parts included in th[...]

  • Page 21

    Technical Data 312350E 21 Te c h n i c a l D a t a T ypical Fluid Outlet Pressure Max grease ou tput pressu re..................... ................ ......... 7500 psi (5 1 MP a, 517 b ar) Max hydraulic fluid input pre ssure.................... ................ 600 psi (4.1 MPa, 41 bar) Max hydraulic fluid input volume ............ ................[...]

  • Page 22

    Technica l Data 22 312350E Dimensions and Mounting Hole La y out 1/8 npt throat seal weep por t 3/4” - 16 JIC 37° flare (m) 1/2 npt(f) fluid outlet 3/4 npt Hydraulic Outlet 14.75 in. (375 mm) 41.5 in. (1054 mm) Model 247443 48.5 in. (1232 mm) Model 247450 3.5 (88.9 mm) minimum diameter clearance hole 3.536 in. (90.424 mm) 3.536 in. (90.424 mm) c[...]

  • Page 23

    Notes 312350E 23 Notes[...]

  • Page 24

    Graco Standard Warra nty 24 312350E Graco Standar d W arranty Graco warrants all equipment ref erenced in th is document which is manuf actured by Graco and bearing its name to be free from de fe c t s in material and workmanship on the date of sale to the origin al purch aser for use. With the e xception of any special, e xtended, or limited warra[...]