Gigabyte GA-H57M-USB3 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Gigabyte GA-H57M-USB3, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Gigabyte GA-H57M-USB3 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Gigabyte GA-H57M-USB3. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Gigabyte GA-H57M-USB3 should contain:
- informations concerning technical data of Gigabyte GA-H57M-USB3
- name of the manufacturer and a year of construction of the Gigabyte GA-H57M-USB3 item
- rules of operation, control and maintenance of the Gigabyte GA-H57M-USB3 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Gigabyte GA-H57M-USB3 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Gigabyte GA-H57M-USB3, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Gigabyte service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Gigabyte GA-H57M-USB3.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Gigabyte GA-H57M-USB3 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    GA-H57M-USB3 GA-H55M-USB3 LGA1 156 socket motherboard for Intel ® Core ™ i7 processor family/ Intel ® Core ™ i5 processor family/ Intel ® Core ™ i3 processor family User's Manual Rev . 1001 12ME-H57MUB3-1001R[...]

  • Page 2

    Motherboard GA-H57M-USB3/ GA-H55M-USB3 Jan. 14, 2010 Jan. 14, 2010 Motherboard GA-H57M-USB3/GA-H55M-USB3[...]

  • Page 3

    Copyright © 2010 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specications and features in this manual may be made by GIGABYTE wit[...]

  • Page 4

    - 4 - T able of Contents Box Contents ................................................................................................................... 6 Optional Items ................................................................................................................. 6 GA-H57M-USB3/GA-H55M-USB3 Motherboard Layout ..................[...]

  • Page 5

    - 5 - Chapter 3 Drivers Installation ........................................................................................ 61 3-1 Installing Chipset Drivers ............................................................................... 61 3-2 Application Software ..................................................................................[...]

  • Page 6

    - 6 - Box Contents GA-H57M-USB3 or GA-H55M-USB3 motherboard Motherboard driver disk User's Manual Quick Installation Guide One IDE cable T wo SA T A 3Gb/s cables I/O Shield Optional Items Floppy disk drive cable (Part No. 12CF1-1FD001-7*R) 2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R) 2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R) [...]

  • Page 7

    - 7 - GA-H57M-USB3/GA-H55M-USB3 Motherboard Layout j Only for GA-H57M-USB3. k Only for GA-H55M-USB3. KB_USB VGA_DVI CPU_F AN SYS_F AN PHASE LED LGA1 156 A TX GA-H57M-USB3/ GA-H55M-USB3 F_AUDIO AUDIO B_BIOS M_BIOS PCIEX16 IDE SPDIF_O DDR3_2 DDR3_1 DDR3_4 DDR3_3 BA T TSB43AB23 IT8720 A TX_12V_2X4 Intel ® H57 j Intel ® H55 k GI G AB Y TE SA T A2 PCI[...]

  • Page 8

    - 8 - GA-H57M-USB3/GA-H55M-USB3 Motherboard Block Diagram j Only for GA-H57M-USB3. k Only for GA-H55M-USB3. (Note 1) Y ou can use only one of the onboard digital graphics ports (e.g. DisplayPort, HDMI, and DVI-D) for output when in the BIOS Setup program or when during the POST screens. (Note 2) Two share the same ports with USB 3.0. 12 USB Ports ([...]

  • Page 9

    - 9 - Hardware Installation 1- 1 Installation Pr ecautions Th e m ot her bo ar d c on ta in s n um er ou s d el ic at e e le ct ro ni c c ir cu it s a nd comp one nt s w hi ch can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures: • Prio r to in[...]

  • Page 10

    Hardware Installation - 10 - 1- 2 Product Specications CPU w Support for an Intel ® Core ™ i7 series processor/Intel ® Core ™ i5 series processor/ Intel ® Core ™ i3 series processor in the LGA1 156 package (Go to GIGABYTE's website for the latest CPU support list.) w L3 cache varies with CPU Chipset  w  Intel ® H57 Expres[...]

  • Page 11

    - 1 1 - Hardware Installation w iTE IT8720 chip: - 1 x oppy disk drive connector supporting up to 1 oppy disk drive USB w Chipset: - Up to 14 USB 2.0/1.1 ports (6 on the back panel (Note 7) , 8 via the USB brackets connected to the internal USB headers) j - Up to 12 USB 2.0/1.1 ports (6 on the back panel (Note 7) , 6 via the USB brackets conn[...]

  • Page 12

    Hardware Installation - 12 - (Note 1) Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. (Note 2) T o use the onboard DisplayPort, HDMI, DVI-D, and D-Sub ports, you must install an Intel CPU with integrated graphics. (Note 3) The DVI-D port[...]

  • Page 13

    - 13 - Hardware Installation 1-3 Installing the CPU and C PU C ooler Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.) • Always turn off the computer and unplug the power cord from the power outlet before in[...]

  • Page 14

    Hardware Installation - 14 - Step 1: Gently press the CPU socket lever handle down and away from the socket with your nger . Then completely lift the CPU socket lever and the metal load plate will be lifted as well. Step 3: Hold the CPU with your thumb and index ngers. Align the CPU pin one marking (triangle) with the pin one corner o f the C[...]

  • Page 15

    - 15 - Hardware Installation Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU. 1-3 -2 I nst all ing t he CPU Cool er Follow the steps below to correctly install the CPU cooler on the motherboard. (The following [...]

  • Page 16

    Hardware Installation - 16 - 1- 4 Installin g the Me mor y Dual Channel Memory Congurations T able (SS=Single-Sided, DS=Double-Sided, "- -"=No Memory) Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installe[...]

  • Page 17

    - 17 - Hardware Installation 1- 4 -2 Inst al ling a M emo r y Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard. Notch DDR3 D[...]

  • Page 18

    Hardware Installation - 18 - 1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. • Always turn off the computer and unplug the power cord from the power outlet before in[...]

  • Page 19

    - 19 - Hardware Installation 1-6 Back Panel Connectors USB 2.0/1.1 Port The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB key - board/mouse, USB printer , USB ash drive and etc. PS/2 Keyboard/Mouse Port Use this port to connect a PS/2 keyboard or mouse. D-Sub Port (Note 1) The D-Sub port supports a[...]

  • Page 20

    Hardware Installation - 20 - DiplayPort (Note 1) (Note 3) DisplayPort is one of the new generation interface technologies that delivers high quality digital imaging and audio, supporting bi-directional audio transmition. DisplayPort can support both DPCP and HDCP content protection mechanisms. Connect the audio/video device that supports DisplayPor[...]

  • Page 21

    - 21 - Hardware Installation • When removing the cable connected to a back panel connector , rst remove the cable from your device and then remove it from the motherboard. • When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector . In additi[...]

  • Page 22

    Hardware Installation - 22 - 1- 7 Inter nal Connectors Read the following guidelines before connecting external devices: • First make sure your devices are compliant with the connectors you wish to connect. • Bef ore in stal ling t he de vice s, be s ure to turn o ff the de vice s and yo ur co mput er. Un plug t he power cord from the pow[...]

  • Page 23

    - 23 - Hardware Installation Pin No. Denition 1 GND ( Only fo r 2x 4-pi n 12 V) 2 GND ( Only fo r 2x 4-pi n 12 V) 3 GND 4 GND 5 +12V (Onl y f or 2 x4-p in 1 2V) 6 +12V (Onl y f or 2 x4-p in 1 2V) 7 +12V 8 +12V A TX_12V_2X4: G.QBOFM 13 1 24 12 A TX A TX: Pin No. Denition 13 3.3V 14 -12V 15 GND 16 PS_ON (soft On/Off) 17 GND 18 GND 19 GND 20 -5V[...]

  • Page 24

    Hardware Installation - 24 - 3/4) CPU_F AN/SYS_F AN (Fan Headers) The motherboa rd has a 4-pin CPU fan header (CPU_F AN ) and a 4-pin (SYS_F AN). Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard supports[...]

  • Page 25

    - 25 - Hardware Installation 6) IDE (IDE Connector) The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attach- ing the IDE cable, locate the foolproof groove on the connector . If you wish to connect two IDE devices, remember to set the jumpers and th e cabling accordi ng to the role o f the IDE devices [...]

  • Page 26

    Hardware Installation - 26 - 8) GSA T A2_5/6 (SA T A 3Gb /s C onn ec to rs , C on tr ol led b y GI GAB YT E SA T A2 ) The SA T A connectors conform to SAT A 3Gb/s standard and are compatible with SA T A 1.5Gb/s standard. Each SA T A connector supports a single SA T A device. The GIGABYTE SA T A2 controller supports RAID 0 and RAID 1. Refer to Chapt[...]

  • Page 27

    - 27 - Hardware Installation 10) F_P ANEL (Front Panel Header) Conne ct the p ower s witch , rese t swit ch, sp eaker, chassi s intr usio n switc h/se nsor an d syst em sta tus indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. Power LED G.QBOFM 1 2 19 20[...]

  • Page 28

    Hardware Installation - 28 - 1 1) F_AUDIO (Front Panel Audio Header) The front panel audio header supports Intel High Denition audio (HD) an d AC'97 audio. Y ou may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module con - nector match the pin assignments of the motherboard header. Inco[...]

  • Page 29

    - 29 - Hardware Installation Pin No. Denition 1 Power 2 SPDIFI 3 GND 13) SPDIF_I (S/PDIF In Header) This header supports digital S/PDIF In and can connect to an audio device that supports digital audio out via an optional S/PDIF In cable. For purchasing the optional S/PDIF In cable, please contact the local dealer . Pin No. Denition 1 SPDIFO [...]

  • Page 30

    Hardware Installation - 30 - 15/16) F_USB1/F_USB2/F_USB3/F_USB4 j (USB Headers) The headers conform to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer . Pin No. Denition 1 Power (5V) 2 Power (5V) 3 USB DX- 4 USB DY - 5 USB [...]

  • Page 31

    - 31 - Hardware Installation 18) COMA (Serial Port Header) The COMA header can provide one serial port via an optional COM port cable. For purchasing the op- tional COM port cable, please contact the local dealer . Pin No. Denition 1 NDCD- 2 NSIN 3 NSOUT 4 NDTR- 5 GND 6 NDSR- 7 NRTS- 8 NCTS- 9 NRI- 10 No Pin 10 9 2 1 19) CLR_CMOS (Clearing CMOS [...]

  • Page 32

    Hardware Installation - 32 - 20) PHASE LED The n umb er of l igh ted L EDs i ndi cate s the CPU l oadi ng. Th e hig her t he CP U loa din g, th e mor e th e number of lighted LEDs. T o enable the Phase LED display function, please rst enable Dynamic Energy Saver ™ 2. Refer to Chapter 4, "Dynamic Energy Saver ™ 2," for more details.[...]

  • Page 33

    - 33 - BIOS Setup BIOS (Ba sic Inpu t and Out put Syst em) reco rds hard ware par ameters of the sy stem in t he CMOS o n the motherboard. Its major functions include conducting the Power-On Self-T est (POST) during system startup, saving sy stem param eters and l oading op erating sy stem, etc . BIOS incl udes a BIO S Setup pro gram that allows th[...]

  • Page 34

    BIOS Setup - 34 - 2-1 Startup Screen The following screens may appear when the computer boots. A. The LOGO Screen (Default) B. The POST Screen Function Keys: <T AB>: POST SCREEN Press the <T ab> key to show the BIOS POST screen. T o show the BIOS POST screen at system startup, refer to the instructions on the Full Screen LOGO Show item [...]

  • Page 35

    - 35 - BIOS Setup 2-2 The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use ar- row keys to move among the items and press <Enter> to accept or enter a sub-menu. (Sample BIOS V ersion: E8) Main Menu Help The on-screen description of a highlighted setup option is displayed on the bottom [...]

  • Page 36

    BIOS Setup - 36 -  The Functions of the <F1 1> and <F12> keys (For the Main Menu Only)  F1 1: Save CMOS to BIOS This function allows you to save the current BIOS settings to a prole. Y ou can create up to 8 proles (Prole 1-8) and name each prole. First enter the prole name (to erase the default prole name, use[...]

  • Page 37

    - 37 - BIOS Setup 2-3 MB Intelligent T weaker(M.I.T .) Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall system congurations. Incorrectly doing overclock/overvoltage may result in dam - age to CPU, chipset, or memory and reduce the useful life of these components. This page is for a[...]

  • Page 38

    BIOS Setup - 38 - CPU Clock Ratio (Note) Allows you to alter the clock ratio for the installed CPU. The item is present only if a CPU with unlocked clock ratio is installed. CPU Frequency Displays the current operating CPU frequency . (Note) This item is present only if you install a CPU that supports this feature. For more information about Intel [...]

  • Page 39

    - 39 - BIOS Setup (Note) This item is present only if you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website. C3/C6/C7 State Support (Note) Allows you to determine whether to let the CPU enter C3/C6/C7 mode in system halt state. When en- abled, the CPU core freque[...]

  • Page 40

    BIOS Setup - 40 - (Note) This item appears only if you install a memory module that supports this feature. Extreme Memory Prole (X.M.P .) (Note) Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when enabled. Disabled Disables this function. (Default) Prole1 Uses Prole 1 settings. Prole2 (Note) U[...]

  • Page 41

    - 41 - BIOS Setup CMOS Setup Utility-Copyright (C) 1984-2009 A ward Software Advanced Memory Settings higf : Move Enter: Select +/-/PU/PD: V alue F10: Save ESC: Exit F1: General Help F5: Previous V alues F6: Fail-Safe Defaults F7: Optimized Defaults Item Help Menu Level   ExtremeMemoryProle(X.M.P .) (Note) [Disabled] System [...]

  • Page 42

    BIOS Setup - 42 - >>>>> Channel A/B T iming Settings >>>>> Channel A/B Standard T iming Control CAS Latency Time Options are: Auto (default), 6~15. tRCD Options are: Auto (default), 1~15. tRP Options are: Auto (default), 1~15. tRAS Options are: Auto (default), 1~31. >>>>> Channel A/B Advanced Timing Cont[...]

  • Page 43

    - 43 - BIOS Setup tRTP Options are: Auto (default), 1~15. t FAW Options are: Auto (default), 1~63. Command Rate(CMD) Options are: Auto (default), 1~3. >>>>> Channel A/B Misc T iming Control Static tRD Options are: Auto (default), 1~31.  Advanced V oltage Settings CMOS Setup Utility-Copyright (C) 1984-2009 A ward Software Advanced [...]

  • Page 44

    BIOS Setup - 44 - >>> MCH/ICH PCH Core The default is Auto . CPU PLL The default is Auto . >>> DRAM DRAM V oltage The default is Auto . DRAM T ermination The default is Auto . Ch-A Data VRef. The default is Auto . Ch-B Data VRef. The default is Auto . Ch-A Address VRef. The default is Auto . Ch-B Address VRef. The default is Auto [...]

  • Page 45

    - 45 - BIOS Setup This section provides information on the BIOS version, CPU base clock, CPU frequency , memory frequency , total memory size , CPU temperature, Chipset temperature, Vcore, and memory voltage. CMOS Setup Utility-Copyright (C) 1984-2009 A ward Software MB Intelligent T weaker(M.I.T .)  M.I.T Current Status [Press Enter]  Advanc[...]

  • Page 46

    BIOS Setup - 46 - Date (mm:dd:yy) Sets the system date. The date format is week (read-only), month, date and year . Select the desired eld and use the up arrow or down arrow key to set the date. Time (hh:mm:ss) Sets the system time. For example, 1 p.m. is 13:0:0. Select the desired eld and use the up arrow or down arrow key to set the time. I[...]

  • Page 47

    - 47 - BIOS Setup • None If no IDE/SA T A devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. • Manual Allows you to manually enter the specications of the hard drive when the hard drive access mode is set to CHS . Access Mode Sets the hard drive access [...]

  • Page 48

    BIOS Setup - 48 - (Note) This item is present only if you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website. 2-5 Advanced BIOS Features Hard Disk Boot Priority Species the sequence of loading the operating system from the installed hard drives. Use the up or d[...]

  • Page 49

    - 49 - BIOS Setup Limit CPUID Max. to 3 (Note) Allows you to determine whether to limit CPUID maximum value. Set this item to Disabled for Windows XP operating system; set this item to Enabled for legacy operating system such as Windows NT4.0. (Default: Disabled) No-Execute Memory Protect (Note) Enables o r disable s Intel Ex ecute Dis able Bit f u[...]

  • Page 50

    BIOS Setup - 50 - 2-6 Integrated Peripherals eXtreme Hard Drive (XHD) (Intel H57 Chipset) j Enab les or disab les t he X.H .D fun ctio n for t he SAT A cont roll ers in tegr ated i n the I ntel H57 Ch ipse t. When set to Enabled , the PCH SAT A Control Mode item below will be set to RAID(XHD) automatically . For deta ils on usin g t he G IGAB YTE X[...]

  • Page 51

    - 51 - BIOS Setup USB Controllers Enables or disables the integrated USB controllers. (Default: Enabled) Disabled will turn off all of the USB functionalities below . USB Legacy Function Allows USB keyboard to be used in MS-DOS. (Default: Enabled) USB Storage Function Determines whether to detect USB storage devices, including USB ash drives and[...]

  • Page 52

    BIOS Setup - 52 - Onboard LAN Boot ROM Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip. (Default: Disabled) Onboard USB 3.0 Controller (NEC USB 3.0 Controller) Enables or disables the NEC USB 3.0 controller . (Default: Enabled) Onboard SA T A/IDE Device (GIGABYTE SA T A2, IDE and GSA T A2_5/6 Connectors) E[...]

  • Page 53

    - 53 - BIOS Setup ACPI Suspend T ype Species the ACPI sleep state when the system enters suspend. S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode. The system can be resumed at any time. S3(STR) Enables the system to enter the ACPI S3 (Su[...]

  • Page 54

    BIOS Setup - 54 - (Note) Supported on Windows 7/Vista operating system only . Resume by Alarm Determines whether to power on the system at a desired time. (Default: Disabled) If enabled, set the date and time as following: Date (of Month) Alarm: Turn on the system at a specic time on each day or on a specic day in a month. Time (hh: mm: ss) A[...]

  • Page 55

    - 55 - BIOS Setup Reset Case Open Status Keeps or clears the record of previous chassis intrusion status. Enabled clears the record of previous chassis intrusion status and the Case Opened eld will show "No" at next boot. (Default: Disabled) Case Opened Displays the detection status of the chassis intrusion detection device attached to[...]

  • Page 56

    BIOS Setup - 56 - CPU Smart F AN Mode Species how to control CPU fan speed. This item is congurable only if CPU Smart F AN Control is set to Enabled . Auto Lets the BIOS automatically detect the type of CPU fan installed and sets the optimal CPU fan control mode. (Default) Voltage Sets Voltage mode for a 3-pin CPU fan. PWM Sets PWM mode for a[...]

  • Page 57

    - 57 - BIOS Setup Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings. In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable BIOS settings for the motherboard. 2-9 Load Fail-Safe Defaults Press <Enter> on this item and then press t[...]

  • Page 58

    BIOS Setup - 58 - Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. Y ou will be requested to conrm the password. T ype the password again and press <Enter>. The BIOS Setup program allows you to specify two separate passwords: Supervisor Password When a system password is set and t[...]

  • Page 59

    - 59 - BIOS Setup Press <Enter> on this item and press the <Y> key . This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-12 Save & Exit Setup Press <Enter> on this item and press the <Y> key. This exits the BIOS Setup without saving [...]

  • Page 60

    BIOS Setup - 60 -[...]

  • Page 61

    - 61 - Drivers Installation 3-1 Installing Chipset Drivers Chapter 3 Drivers Installation • Before installing the drivers, rst install the operating system. • After installing the operating system, insert the motherboard driver disk into your optical drive. The driver Autorun screen is automatically displayed which looks like that show[...]

  • Page 62

    Drivers Installation - 62 - 3-2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software. Y ou can click the Install button on the right of an item to install it. 3-3 T echnical Manuals This page provides GIGABYTE's application guides, content descriptions for this driver disk, an[...]

  • Page 63

    - 63 - Drivers Installation 3-4 Contact For the detailed contact information of the GIGABYTE T aiwan headquarter or worldwide branch ofces, click the URL on this page to link to the GIGABYTE website. 3-5 System This page provides the basic system information.[...]

  • Page 64

    Drivers Installation - 64 - 3-6 Download Center T o update the BIOS, driver s, or applications, click the Download Center but ton to link to the GIGAB YTE website. The latest version of the BIOS, drivers, or applications will be displayed. 3-7 New Utilities This page provides a quick link to GIGABYTE's lately developed utilities for users to i[...]

  • Page 65

    - 65 - Unique Features 4-1 Xpress Recovery2 Chapter 4 Unique Features Xp r es s R e co v er y 2 i s a u ti l it y t h at a l l ow s y ou to q u ic k l y co m p re s s an d back up your system data and perform restoration of it. Supporting NTFS, F A T32, and FA T16 le systems, Xpress Recovery2 can back up data on P AT A and SA T A hard drives and[...]

  • Page 66

    Unique Features - 66 - Step 3: Wh e n pa r ti t io n in g y o ur h a rd d r i ve , m ak e s ur e t o leave unallocated space (10 GB or more is recom- mended; actual size requirements vary , depending on the amount of data) and begin the installation of the operating system. Step 1: Select BACKUP to start backing up your hard drive data. Step 4: Aft[...]

  • Page 67

    - 67 - Unique Features D. Using the Restore Function in Xpress Recovery2 E. Removing the Backup F . Exiting Xpress Recovery2 Sel ec t RESTORE to re st or e th e ba ck up t o yo ur h ar d dr ive in case the system breaks down. The RESTORE option will not be present if no backup is created before. Select REBOOT to exit Xpress Recovery2. Step 2: After[...]

  • Page 68

    Unique Features - 68 - 4-2 BIOS Update Utilities GI GA B YT E m ot h er b oa r ds p r ov i de t w o un i qu e B IO S u pd a te t o ol s , Q- F la s h ™ an d @ BI O S ™ . GI G AB Y TE Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS mod e. Ad dit ion all y , this m oth erb oar d fe atu res t he [...]

  • Page 69

    - 69 - Unique Features B. Updating the BIOS When updatin g the BIOS, ch oose the loc ation where t he BIOS le is saved. The followi ng procedure as - sumes that you save the BIOS le to a USB ash drive. Step 1: 1. Insert the USB ash drive containing the BIOS le into the computer . In the main menu of Q-Flash, use the up or down arrow [...]

  • Page 70

    Unique Features - 70 - Step 4: Press <Esc> and then <Enter> to exit Q-Flash and reboot the system. As the system boots, you should see the new BIOS version is present on the POST screen. Step 5: During the POST , press <Delete> to enter BIOS Setup. Select Load Optimized Defaults and press <Enter> to load BIOS defaults. Syste[...]

  • Page 71

    - 71 - Unique Features 4-2-2 Updating the BIOS with the @BIOS Utility A. Before Y ou Begin 1. In Windows, close all applications and TSR (T erminate and Stay Resident) programs. This helps prevent unexpected failures when performing a BIOS update. 2. Du ring the BIOS upd ate proc ess, ens ure the I nternet connect ion is st able an d do NOT inte rr[...]

  • Page 72

    Unique Features - 72 - 4-3 EasyT une 6 GIGABYTE's EasyTune 6 is a simple and easy-to-use interface that allows users to ne-tune their system settings or do overclock/overvoltage in Windows environment. The user-friendly EasyTune 6 interface also includes tabbed pages for CPU and memory information, letting users read their system-related in[...]

  • Page 73

    - 73 - Unique Features 4-4 Dynamic Energy Saver ™ 2 GIGABYTE Dynamic Energy Sav er ™ 2 (Note 1) is a revolutionary tech nology that delivers unpara lleled power savings with a click of the button. Featuring an advanced proprietary hardware and software design, GIGA- BYTE Dynamic Energy Saver ™ 2 is able to provide exceptional power savings an[...]

  • Page 74

    Unique Features - 74 - B. T otal Mode In T otal Mode, users are able to see how much total power savings they have accumulated in a set period of time since activating Dynamic Energy Saver ™ 2 for th e rst time (Note 3) . (Note 1) Before using the Dynamic Energy Saver ™ 2 function, make sure the CPU Enhanced Halt (C1E) and CPU EIST Function [...]

  • Page 75

    - 75 - Unique Features 4-5 Q-Share Q-Share is an easy and convenient data sharing too l. After conguring your LAN connection settings and Q-Share, you are able to share your data with computers on the same network, making full use of Internet resources. Directions for using Q-Share After installing Q-Share from the motherboard driver disk, go to[...]

  • Page 76

    Unique Features - 76 - 4-6 Smart 6 ™ GIGABYTE Smart 6 ™ (Note 1) is designed with user-friendliness i n mind, and offers a combination of 6 innovative software utilities that provide easier and smarter PC system management. Smart 6 ™ allows you to speed up system performance, reduce boot-up time, manage a secure platform and recover specie[...]

  • Page 77

    - 77 - Unique Features SMART Recovery With SMART Recovery , users can quickly create backups of changed data les (Note 2) or copy les from a specic backup on P A T A and SA T A hard drives (partitioned on NTFS le system) in Windows Vista. SMART DualBIOS SMART DualBIOS is a new feature that can record personal passwords and important dat[...]

  • Page 78

    Unique Features - 78 - (Note 1) When launching Smart 6 ™ for the rst time, the system will request you to set up a password. This password is required when you activate SMART DualBIOS or when you want to make changes to the SMART Recorder or SMART TimeLock settings. (Note 2) The changed data refers to the data that has been modied, deleted,[...]

  • Page 79

    - 79 - Unique Features 4-7 Auto Green Auto Green is an easy-to-use tool that provides users with simple options to enable system power savings via a Bluetooth cell phone. When the phone is out of the range of the computer's Bluetooth receiver , the sys- tem will enter the specied power saving mode. Sele cti ng a s yste m e ner gy s avi ng m[...]

  • Page 80

    Unique Features - 80 - With GIGABYTE eXtreme Hard Drive (X.H.D) (Note 1) , users can quickly congure a RAID- ready system for RAID 0 when a new SA T A drive is added. For a RAID 0 array that al- ready exists, users also can use X.H.D to easily add a hard drive into the array to expand its capacity . All with a simple click of a button, X.H.D hel[...]

  • Page 81

    - 81 - Appendix Chapter 5 Appendix 5-1 Conguring SA T A Hard Drive(s) T o congure SA T A hard drive(s), follow the steps below: A. Install SA T A hard drive(s) in your computer . B. Congure SA T A controller mode in BIOS Setup. C. Congure a RAID array in RAID BIOS. (Note 1) D. Make a oppy disk containing the SA T A RAID/AHCI driver f[...]

  • Page 82

    Appendix - 82 - B. Conguring SA T A controller mode in BIOS Setup Make sure to congure the SA TA controller mode correctly in system BIOS Setup. Step 1: Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-T est). T o create RAID, set PCH SA T A Control Mode under the Integrated Peripherals menu to[...]

  • Page 83

    - 83 - Appendix C. Conguring a RAID array in RAID BIOS Enter the RAID BIOS setup utility to congure a RAID array . Skip this step and proceed with the installation of Windows operating system for a non-RAID conguration. Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says &quo[...]

  • Page 84

    Appendix - 84 - Step 3: After entering the CREA TE VOLUME MENU screen, enter a volume name with 1~16 letters (letters cannot be special characters) under the Name item and press <Enter>. Then, select a RAID level (Figure 4). RAID levels supported include RAID 0, RAID 1, Recovery , RAID 10, and RAID 5 (the selections available depend on the nu[...]

  • Page 85

    - 85 - Appendix Step 5: Enter the array capacity and press <Enter>. Finally press <Enter> on the Create V olume item to begin creat- ing the RAID array . When prompted to conrm whether to create this volume, press <Y> to conrm or <N> to cancel (Figure 6). When completed, you can see detailed information about the RAID [...]

  • Page 86

    Appendix - 86 - Recovery V olume Options Intel Rapid Recover T echnology provides data protection by allowing users to easily restore data and system operation using a designated recovery drive. With the Rapid Recovery T echnology , which employs RAID 1 functionality , users can copy the data from the master drive to the recovery drive; if needed, [...]

  • Page 87

    - 87 - Appendix Figure 10 Step 3: Press <Enter> under the Select Disks item. In the SELECT DISKS box, press <T ab> on the hard drive you want to use for the master drive and press <Space> on the hard drive you want to use for the recovery drive. (Make sure the recovery drive has equal or larger capacity than the master drive.) The[...]

  • Page 88

    Appendix - 88 - Delete RAID V olume T o delete a RAID array, select Delete RAID V olume in MAIN MENU and pres s <Enter>. In the DELETE VOLUME MENU section, use the up or down arrow key to select the array to be deleted and press <Delete>. When prompted to conrm your selection (Figure 12), press <Y> to conrm or <N> to a[...]

  • Page 89

    - 89 - Appendix 5-1-2 Conguring GIGABYTE SA T A2 SA T A Controller A. Installing SA T A hard drive(s) in your computer Attach one end of the SA TA signal cable to the rear of the SA T A hard drive and the other end to available SA TA port on the motherboard. On this motherboard, the GSA T A2_0 and GSA T A2_1 ports are supported by the GIGABYTE S[...]

  • Page 90

    Appendix - 90 - C. Conguring a RAID array in RAID BIOS Enter the RAID BIOS setup utility to congure a RAID array . Skip this step and proceed to the installation of Windows operating system for a non-RAID conguration. After the POST memory test begins and before the operating system boot begins, look for a message which says "Press &l[...]

  • Page 91

    - 91 - Appendix Create a RAID Array: In the main screen, press <Enter> on the Create RAID Disk Drive item. Then the Create New RAID screen appears (Figure 4). The Create New RAID block displays all the items that need to be set for creating an array (Figure 5). Steps: 1. Enter Array Name: Under the Name item, enter an array name with 1~16 let[...]

  • Page 92

    Appendix - 92 - 3. Assign Array Disks: After a RAID mode is selected, RAID BIOS automaticall y assigns the two hard drives installed as the RAID drives. 4. Set Block Size (RAID 0 only): Under the Block item, use the up or down arrow key to select the stripe block size (Figure 6), ranging from 4 KB to 128 KB. Press <Enter>. 5. Set Array Size: [...]

  • Page 93

    - 93 - Appendix When nished, the new RAID array will be displayed in the RAID Disk Drive List block (Figure 8). Figure 8 Model Name RAID Level Capacity Status Members(HDDx) RDD0: GRAID 0-Stripe 240 GB Normal 01 [ fg T AB]-Switch Window [ hi ]-Select ITEM [ENTER]-Action [ESC]-Exit [ RAID Disk Drive List ] [ Main Menu ] [ Hard Disk Drive List ] Gi[...]

  • Page 94

    Appendix - 94 - Model Name RAID Level Capacity Status Members(HDDx) RDD0: GRAID 0-Stripe 240 GB Normal 01 [ fg T AB]-Switch Window [ hi ]-Select ITEM [ENTER]-Action [ESC]-Exit [ RAID Disk Drive List ] [ Main Menu ] [ Hard Disk Drive List ] Gigabyte T echnology Corp. RAID Setup Utility v1.07.06 Create RAID Disk Drive Delete RAID Disk Drive Revert HD[...]

  • Page 95

    - 95 - Appendix 5-1-3 Making a SA T A RAID/AHCI Driver Diskette (Required for AHCI and RAID Mode) T o successfully install operating system onto SA T A hard drive(s) that is/are congured to RAID/AHCI mode, you need to install the SA T A controller driver during the OS installation. Without the driver , the hard drive may not be recognized during[...]

  • Page 96

    Appendix - 96 - 5-1-4 Installing the SA T A RAID/AHCI Driver and Operating System With the SA T A RAID/AHCI driver diskette and correct BIOS settings, you are ready to install Windows Vista/ XP onto your hard drive(s). The followings are examples of Windows XP and Vista installation. A. Installing Windows XP Step 1: Restart your system to boot from[...]

  • Page 97

    - 97 - Appendix For the GIGABYTE SA TA2: Insert the oppy disk containing the SA T A RAID/AHCI driver and press <S>. Then a controller menu similar to Figure 3 below will appear. Select RAID/AHCI Driver for GIGABYTE GBB36X Controller (x32) and press <Enter>. Step 3: On the next screen, press <Enter> to continue the driver instal[...]

  • Page 98

    Appendix - 98 - B. Installing Windows Vista (The procedure below assumes that only one RAID array exists in your system.) For the Intel H57: Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears, select Load Driver (Figure 4). Step 2: Inse rt th [...]

  • Page 99

    - 99 - Appendix Step 3: When a screen as shown in Figure 6 appears, select Intel(R) ICH8R/ICH9R/ICH10R/DO/5 Series/3400 Se- ries SA TA RAID Controller and click Next . Step 4: After the driver is loaded, select the RAID/AHCI drive(s) where you want to install the operating system and then click Next to continue the OS installation (Figure 7). Figur[...]

  • Page 100

    Appendix - 100 - For the GIGABYTE SA TA2: Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears (RAID/AHCI hard drive(s) will not be detected at this stage), select Load Driver (Figure 8). Step 2: Insert the motherboard driver disk (Method A) or [...]

  • Page 101

    - 101 - Appendix Step 3: When a screen as shown in Figure 10 appears, select GIGABYTE GBB36X Controller and click Next . Step 4: After the driver is loaded, select the RAID/AHCI drive(s) where you want to install the operating system and then click Next to continue the OS installation (Figure 1 1). Figure 10 Figure 1 1[...]

  • Page 102

    Appendix - 102 - Intel(R) Rapid Storage T echnology - option ROM - 9.5.0.1037 Copyright(C) 2003-09 Intel Corporation. All Rights Reserved. 3. Reset Disks to Non-RAID 4. Exit RAID V olumes : Nonedened. Physical Disks : Port Drive Model Serial # Size T ype/Status(V ol ID) 0 ST3120026AS 3JT354CP 11 1.7GB Member Disk (0) 1 WDC WD800JD-22LS WD-WMA[...]

  • Page 103

    - 103 - Appendix • Performing the Rebuild in the Operating System While in the operating system, make sure the chipset driver has been installed from the motherboard driver disk. Then launch the Intel Rapid Stroage T echnology utility from All Programs in the Start menu. Step 1: Go to t he Ma nage m enu a nd cl ick Re buil d to another disk in Ma[...]

  • Page 104

    Appendix - 104 - • Restoring the Master Drive to a Previous State (for Recovery V olume only) When two hard drives are set to Recovery Volume in Update on Request mode, you can restore the master drive data to the last backup state when needed. For example, in case the master drive detects a virus, you can restore the recovery drive data to the m[...]

  • Page 105

    - 105 - Appendix For the GIGABYTE SA TA2: Turn off your computer and replace the failed hard drive with a new one. Use either the RAID setup utility or the GIGABYTE RAID CONFIGURER utility in the operating system to perform the rebuild. • Rebuilding with the RAID setup utility Step 1: When the message "Press <Ctrl-G> to enter RAID Setu[...]

  • Page 106

    Appendix - 106 - • Rebuilding in the operating system Make sure the GIGABYTE SA T A2 SA T A controller driver has been installed from the motherboard driver disk. Launch the GIGABYTE RAID CONFIGURER from All Programs in the Start menu. Step 1: In the GIGABYTE RAID CONFIGURER screen, right-click on the array to be rebuilt in the RAID LIST block. S[...]

  • Page 107

    - 107 - Appendix 5-2-1 Conguring 2/4/5.1/7.1-Channel Audio Th e mo t h e r b o a r d p r o v i d e s s i x a u d i o j a c k s o n t h e ba c k p a ne l w h i c h su p p o rt 2/ 4 / 5. 1 / 7 .1 - c h an n e l (Note) audio. The picture to the right shows the default audio jack assignments. The integrated HD (High Definition) audio provides jack r[...]

  • Page 108

    Appendix - 108 - Step 2: Connect an audio device to an audio jack. The The cur- rent connected device is dialog box appears. Select the device according to the type of device you connect. Then click OK . Step 3: On the Speakers s creen, click t he Spe aker Co ngura - tion tab. In the Speaker Conguration list, select Stereo , Quadraphonic , 5.[...]

  • Page 109

    - 109 - Appendix 5-2-2 Conguring S/PDIF In/Out A. S/PDIF In The S/PDIF In cable (optional) allows you to input digital audio signals to the computer for audio processing. 1. Installing the S/PDIF In Cable: 2. Conguring S/PDIF In: On the Digital Input screen, click the Default Format tab to select the default format. Click OK to complete. (Not[...]

  • Page 110

    Appendix - 110 - B. S/PDIF Out The S/PDIF Out jacks can transmit audio signals to an external decoder for decoding to get the best audio quality . 1. Connecting a S/PDIF Out Cable: 2. Conguring S/PDIF Out: On the Digital Output screen, click the Default Format tab and then select the sample rate and bit depth. Click OK to complete. S/PDIF Coaxia[...]

  • Page 111

    - 1 11 - Appendix 5-2-3 Conguring Microphone Recording Step 1: After installing the audio driver , the HD Audio Manager icon will appear in the notication area. Double-click the icon to access the HD Audio Manager . Step 2: Connect your microphone to the Mic in jack (pink) on th e ba c k pa ne l o r th e M ic i n j ac k ( pi nk ) o n th e f r[...]

  • Page 112

    Appendix - 112 - 5-2-4 Enabling the Dolby Home Theater Function Before D olby Hom e Theater is enabled , you get o nly 2-c hannel p layback output ( from the front speakers) when playing 2-channel stereo sources. Y ou must play 4-, 5.1-, or 7.1- chan- nel content to get 4-, 5.1-, or 7.1- channel audio effects. With Dolby Home Theater enabled, 2-cha[...]

  • Page 113

    - 1 13 - Appendix Step 4: T o r a i s e t h e r e co r d i n g a n d p la y b a c k v o lu m e f o r t h e microphone, click the Microphone Boost icon on the right of the Recor ding V olume slider and set the Microphone Boost level. Step 5: After co mpletin g the set tings a bove, cl ick Start , p oint to All Programs , point to Accessories , and t[...]

  • Page 114

    Appendix - 114 - Step 3: When the Stereo Mix item appears, right-click on this item and select Enable . Then set it as the default de- vice. Step 4: Now you can access the HD Audio Manager to cong - ure Stereo Mix and use Sound Recorder to record the sound. 5-2-5 Using the Sound Recorder A. Recording Sound 1. Make sure you have connected the sou[...]

  • Page 115

    - 1 15 - Appendix 5-3 T roubleshooting 5-3-1 Frequently Asked Questions T o read more F AQs for your motherboard, please go to the Support&DownloadsMotherboardFAQ page on GIGABYTE's website. Q: In the BIOS Setup program, why are some BIOS options missing? A: Some advanced options are hidden in the BIOS Setup program. Press <Delete>[...]

  • Page 116

    Appendix - 116 - 5-3-2 T roubleshooting Procedure If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the problem. ST AR T A Turn off the power . Remove all peripherals, connecting cables, and power cord etc. Isolate the short circuit. Secure the CPU cooler on the CPU. Connect the CPU cooler powe[...]

  • Page 117

    - 1 17 - Appendix If the proce dure above is una ble to solv e your p robl em, c onta ct the place of pur chas e or lo cal dealer for help. Or go to the Support&DownloadsT echnical Service Zone page to submit your question. Our customer service staff will reply you as soon as possible. The power supply , CPU or CPU socket might fail. The keybo[...]

  • Page 118

    Appendix - 118 - 5-4 Regulatory Statements Regulatory Notices This document must not be copied without our written permission, and the conten ts there of must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at t[...]

  • Page 119

    - 1 19 - Appendix Finally , we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly . Wi[...]

  • Page 120

    Appendix - 120 -[...]

  • Page 121

    - 121 - Appendix[...]

  • Page 122

    Appendix - 122 -[...]

  • Page 123

    - 123 - Appendix[...]

  • Page 124

    Appendix - 124 -[...]

  • Page 125

    - 125 - Appendix[...]

  • Page 126

    Appendix - 126 -[...]

  • Page 127

    - 127 - Appendix Contact Us • GIGA-BYTE TECHNOLOGY CO., L TD. Address: No.6, Bau Chiang Road, Hsin-Tien, T aipei 231, T aiwan TEL: +886-2-8912-4000 F AX: +886-2-8912-4003 T ech. and Non-T ech. Support (Sales/Marketing) : http://ggts.gigabyte.com.tw WEB address (English): http://www .gigabyte.com.tw WEB address (Chinese): http://www .gigabyte.tw ?[...]

  • Page 128

    Appendix - 128 - • GIGABYTE Global Service System T o subm it a tec hnical or non- techni cal (Sa les/M arket- ing) question, please link to: http://ggts.gigabyte.com.tw Then select your language to enter the system. • G.B.T . TECHNOLOGY TRADING GMBH - Germany WEB address : http://www .gigabyte.de • G.B.T . TECH. CO., L TD. - U.K. WEB addr[...]