English dropdown-ico

Epson F7070 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Epson F7070, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Epson F7070 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Epson F7070. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Epson F7070 should contain:
- informations concerning technical data of Epson F7070
- name of the manufacturer and a year of construction of the Epson F7070 item
- rules of operation, control and maintenance of the Epson F7070 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Epson F7070 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Epson F7070, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Epson service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Epson F7070.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Epson F7070 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Epson® SureColor® F7070 Setup Guide[...]

  • Page 2

    2 | Contents Unpacking the Printer ..................... ...................... ....................... ...................... ................. .................. 3 Assembling the Stand ..... ...................... ....................... ...................... ........................... ....... ....... ............ 6 Installing the Printer .....[...]

  • Page 3

    Unpacking the Printer | 3 Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the printer and in t he User’s Guide . Unpacking the Printer Before beginning assembly, make sure you have suff icient space to set up and use the printer. The following illustration shows the minimum [...]

  • Page 4

    4 | Unpacking the Printer When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations subject to direct sunlig ht, excessive heat, humidity, or dust. Be sure the printer is placed on a flat, stable location that can support 496 lb (225 kg). Caution: Six people are required to un pack and install the p[...]

  • Page 5

    Unpacking the Printer | 5 Media System Assembly The items below can be found in the “Ink Supply System Cove r 1” box. Media feeding unit Take-up reel Reel brackets Adjustment paper Roll core Bracket and mounting hardware[...]

  • Page 6

    6 | Assembling the Stand Assembling the Stand Make sure you have the following items before assembling the stand. 1. Slide the large horizontal strut into both of the legs. 2. Use the long end of the hex wrench to tighten the pre-placed screws on each of the legs. back of stand[...]

  • Page 7

    Assembling the Stand | 7 3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and left legs. 4. Attach the waste ink tank bracket and secure it with a B screw. 5. Attach one B screw to the other side of the bracket, move the slider into place, then attach another B screw.[...]

  • Page 8

    8 | Assembling the Stand 6. Temporarily fasten the waste ink tu be bracket using one B screw. 7. Remove the four screws, then remove the plastic piece. 8. Loosely fasten the mounting pieces to the bracket using three D screws and six washers.[...]

  • Page 9

    Assembling the Stand | 9 9. Slide the mounting pieces into the grooves, as shown. 10. Remove the screw, align the bracket, then fasten the screw to the stand. 11. Tighten the screws.[...]

  • Page 10

    10 | Installing the Printer 12. Replace the plastic piece and then fasten it using the screws from step 7. Installing the Printer You need six people to install the prin ter; four people to carry it and two people to po sition it on the stand. Use the carry bars to lift and move the printer. Make sure you have the following it ems before installing[...]

  • Page 11

    Installing the Printer | 11 2. Insert the carry bars into both sides of the printer with the locking bolts toward the ground. Once the carry bars are inserted, rotate them counterclockwise 180° to lock them into place. This keeps the printer from sliding when lifted. Caution: Before installing the pr inter, make sure the st and is fixed in place. [...]

  • Page 12

    12 | Installing the Printer 4. Lift the printer onto the stand. Line up the marks on the bottom of the print er with the arrows on the top of the stand’s legs before setting the printer down. 5. Rotate the carry bars clockwise 180° so the locking bolts face the ground. Remove the carry bars from the printer. 6. Attach the printer to the stand us[...]

  • Page 13

    Installing the Printer | 13 7. Open the front cove r and remove the tape. 8. Remove the media holding plates. 9. Feed the long waste ink tube through th e ho le in the stand and secure it in place.[...]

  • Page 14

    14 | Installing the Printer 10. Feed the short waste ink tube through the bracket as shown. Then feed the end of the long waste ink tube into the top of the short waste ink tube. 11. Remove the cap and inner seal from the waste ink tank. Note: Keep the cap an d inner seal for the waste ink tank. The tank must be sealed properly for disp osal. 12. I[...]

  • Page 15

    Installing the Media Feeding Unit | 15 13. Place the caution label for your language over the English label, if necessary. Installing the Media Feeding Unit You need the following parts to assemb le and attach the media feeding unit: 1. Attach the brackets to the back side of the printer with two C screws on each side as shown.[...]

  • Page 16

    16 | Installing the Media Feeding Unit Caution: The media feeding unit is heavy and requires two peop le to install. To avoid damaging the media feeding unit, lift it by holding the two bars on the bottom as shown. 2. Lower the media f eeding unit onto the brackets. 3. Attach the media feeding unit to the stand using three C screws.[...]

  • Page 17

    Installing the Media Feeding Unit | 17 4. Attach the media feeding unit to the stand using four C screws. Note: Leave the screws loose until the service eng ineer finishes adjusting the media system. 5. Run the communication cable through t he cable supports. 6. Lift the port cover.[...]

  • Page 18

    18 | Installing the Media Feeding Unit 7. Plug in the communication cable and thread it through the cable supports. 8. Make sure the communication cable is fully seate d in the port and then close the port cover.[...]

  • Page 19

    Installing the Take-up Reel System | 19 Installing the Take- up Reel System You need the following parts to assemble and attach the take-up reel system: 1. Attach the brackets to the front of the printer using two C screws on each side as shown. Caution: Use at least two people to lift the take-up reel. To avoid damaging the take-up reel, lift it b[...]

  • Page 20

    20 | Installing the Take-up Reel System 2. Lower the take-up reel onto the brackets. 3. Attach the take-up reel using three C screws as shown. 4. Attach the take-up reel to the stand using four C screws. Note: Leave the screws loose until the service eng ineer finishes adjusting the media system.[...]

  • Page 21

    Installing the Take-up Reel System | 21 5. Connect the communication cable th at is attached to the take-up reel system by running it through the horizontal struts to the back of the printer. Place the communication cable in the cable sup ports and plug it in, making sure to tighten the scre ws on the plug to secure the cable in place. 6. Attach th[...]

  • Page 22

    22 | Setting the Language 7. Thread the power cord through the cable supports. Connect the p ower cord to the pr inter and use the cable supports to restrain the cord. 8. Contact a service engineer to attach the Epson Genuine Ink Supply System, Ink Supply System Cover 1, and adjust the printer. Do not turn on the printer until the serv ice engineer[...]

  • Page 23

    Adjusting the Media System | 23 Adjusting the Media System After completing printer assembly an d before loading media, mark the lo ading position on the left end of the media using the procedure below. This ensu res that the media will be fed straight and helps reduce printing errors. The operation requires two people to perform any necessary adju[...]

  • Page 24

    24 | Adjusting the Media System 3. Align the bottom of the adjustment paper with the bottom of the lower label on the ejection guide. Align the right side of the adjustment paper with the l ongest scale marks on both labels. After al igning the adjustment paper, lower the media loading lever. 4. At the back of the printer, pull the adjustment pape [...]

  • Page 25

    Loading Media | 25 5. Raise the media loading lever and remove the adjustment paper. Loading Media 1. Turn on the printer.[...]

  • Page 26

    26 | Loading Media 2. Open the front cove r and then raise the media loading lever. 3. Loosen the screws on the roll holders and slide th e roll holders t owards th e outside of the print er. 4. Align the left end of the media with the mark you made on the label.[...]

  • Page 27

    Loading Media | 27 5. Using two or more people, move the media onto the roll holder, adjusting the roll holder as necessary. When the media is securely on the roll holder, tighten th e screw. 6. Turn the roll holder handle counterclockwise until it can not be turned further.[...]

  • Page 28

    28 | Loading Media 7. Pull up the roll holder lever, slide the roll holder into the media roll, and tighten the roll holder screw. 8. Turn the roll holder handle clockwise until part A is hidden. When part A is hidden, do not turn the handle any further.[...]

  • Page 29

    Loading Media | 29 9. Pull the media into the printer. If the left end of the media is not at the center of the rectangular area as shown in the figure on the right, return to step 4. 10. Lower the media loading lever. 11. Pull the media through the front of the printer and then raise the media loading lever.[...]

  • Page 30

    30 | Loading Media 12. Pull the media out until the right end is parallel wi th the scale marks on the two labels. Then lower the media loading lever. 13. Attach the media holding plates while aligning thei r positions. The media holding plates should be installed so that the sides of the media are visible through the three holes and the white line[...]

  • Page 31

    Installing the Software | 31 14. Close the front cover. 15. After loading the media, you will be prompted to choose setup and media options. Choose options as necessary. Installing the Software Insert the software CD that came with your printer into your computer and follow the on-screen instructions. You can use USB or Ethernet network connections[...]

  • Page 32

    32 | USB Installation USB Installation 1. Power off your printer, then connect the US B cable to the printer and your comp uter. 2. Insert the CD into your computer. 3. Follow the on-screen instructions to complete the installation.[...]

  • Page 33

    Network Installation | 33 Network Installation 1. Make sure your printer is powered on. 2. Connect the Ethernet cable to the printer and your networking device. 3. Insert the CD into your computer.[...]

  • Page 34

    34 | Network Insta llation 4. Follow the on-screen instructions to complete the installation, keeping the following points in mind: • Do not remove the checkmark from EpsonNet Configuration Utility and EPSON driv ers and utilities in the software list. • If you see a firewall or network message, make sure the publisher is SEIKO EPSON, and then [...]