Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Echo WP-1000 T1E, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Echo WP-1000 T1E one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Echo WP-1000 T1E. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Echo WP-1000 T1E should contain:
- informations concerning technical data of Echo WP-1000 T1E
- name of the manufacturer and a year of construction of the Echo WP-1000 T1E item
- rules of operation, control and maintenance of the Echo WP-1000 T1E item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Echo WP-1000 T1E alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Echo WP-1000 T1E, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Echo service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Echo WP-1000 T1E.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Echo WP-1000 T1E item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
X750012622 01/10 W ater Pump Operator's Manual MODEL WP-1000 WP-1000 T1E W ARNING Read rules for safe operation and instructions carefully . ECHO provides an Opera- tor's Manual, which must be read and understood for proper and safe operation. Failure to do so could result in serous injury . X7505120502[...]
-
Page 2
2 CopyRight© 2010 By Echo, Incorporated All Rights Reserved. I n t r o d u c t I o n W elcome to the ECHO family . This ECHO product was designed and manufactured to provide long life and on-the-job-dependability . Read and understand this manual that you found in the package. Y ou will nd it easy to use and full of helpful operations tips and [...]
-
Page 3
W a t e r P u m P O P e r a t O r ' s m a n u a l 3 s a f e t y m a n u a l s a f e t y s y m b o l s a n d I m p o r t a n t I n f o r m a t I o n W ARNING The safety alert symbol accompanied by the word “W ARNING” calls attention to an act or condi- tion which CAN lead to serious personal injury or death if not avoided. CIRCLE AND SLASH [...]
-
Page 4
4 Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape Hot Surface Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Symbol description/application Symbol form/shape Symbol description/application Symbol form/shape "W ARNING, SEE OP- ERA TOR' MANUAL Wear eyes, ears a[...]
-
Page 5
W a t e r P u m P O P e r a t O r ' s m a n u a l 5 W ARNING W ater Pump users risk injury to themselves and others if the water pump is used improperly and or safety precau- tions are not followed. Proper clothing and safety gear must be worn when operating a water pump. Failure to do so can result in serious injury . p e r s o n a l c o n d [...]
-
Page 6
6 e q u I p m e n t Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. T ighten and/or replace as needed. • Inspect guards and shield for damage and ensure that they are securely in place. Replace if they are damaged or miss - ing. • Do not operate the pump without an air ?[...]
-
Page 7
W a t e r P u m P O P e r a t O r ' s m a n u a l 7 Hot Decal (near mufer) Extra parts for discharge hose d e s c r I p t I o n Locate the safety decal on your unit. Make sure the decal is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer . See P AR T[...]
-
Page 8
8 1. SP ARK ARRESTOR MUFFLER OR SP ARK ARRESTOR MUFFLER WITH CA T AL YST - The mufer or catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the mufer . Keep exhaust area clear of ammable debris. 2. CARR YING HANDLE - The carrying handle is used to transpor[...]
-
Page 9
W a t e r P u m P O P e r a t O r ' s m a n u a l 9 ____ 1 - Pump Assembly ____ 1 - Suction Hose (#21) ____ 1 - Operator's Manual ____ 1 - W arranty Registration Card ____ 1 - Plastic Bag ____ 1, Garden Hose Adaptor (#23) ____ 3, Hose Clamps (#20) ____ 2, Hose Fittings (#18) ____ 2, Hose Connecter (#19) ____ 2, Sealing W ashers (#17) ____[...]
-
Page 10
10 H B D C E E d I s c h a r g e h o s e Garden Hose NOTE Garden hose ranging from 13 mm (1/2 inch) to 19 mm (3/4 inch) in diameter can be used on the discharge end of this pump. 1. Remove vinyl cap from pump discharge port. 2. Attach the 25 mm to 3/4 inch adaptor (H) and washer (E) tightly onto pump discharge port. 3. Attach garden hose onto adapt[...]
-
Page 11
W a t e r P u m P O P e r a t O r ' s m a n u a l 11 NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual. f u e l W ARNING Alternative fuels, such [...]
-
Page 12
12 Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IMPOR T ANT Spilled fuel is a leading cause of hydrocarbon emissions. Some st[...]
-
Page 13
W a t e r P u m P O P e r a t O r ' s m a n u a l 13 1. Select a rm, level site as near the water source as possible. Never exceed a suction lift (A) of 7.5 m (24 feet) or water will not ow . Make sure pump will not move due to vibration and/or the pull from the weight of suction hose when full of water . 2. T otal vertical discharge (B)[...]
-
Page 14
14 W ARNING W ater can be conductor of electric current when exposed to live electrical wiring. Electrocution will result. • Do not operate pump in ooded basements without rst shutting off electricity from outside the house. Pump should be located outside in a vented area. • Do not operate pump in ooded areas near power lines unless el[...]
-
Page 15
W a t e r P u m P O P e r a t O r ' s m a n u a l 15 s t a r t I n g w a r m e n g I n e The starting procedure is the same as Cold Start except DO NOT close the choke. 1. Move ignition switch (A) to start, move throttle lever (D) towards engine to idle position. Pull starter handle (E) and engine should start. Do not use choke (B). NOTE If en[...]
-
Page 16
16 Y our ECHO water pump is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your water pump achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. T o help you decide whether you want to DO-IT -YOUR -[...]
-
Page 17
W a t e r P u m P O P e r a t O r ' s m a n u a l 17 a I r f I l t e r Level 1. T ools requir ed: Cleaning brush, 25 or 50 mm (1 or 2 in.) Parts r equir ed: REPOWER AIR & FUEL FIL TER KIT . 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air lter is removed. Brush accumulated dir[...]
-
Page 18
18 c o o l I n g s y s t e m Level 2. T ools requir ed: Cross-head Screwdriver , 3 mm Hex W rench, Cleaning Brush. Parts Requir ed: None. IMPOR T ANT T o maintain proper engine operating temperatures, cooling air must pass freely through the cylinder n area. This ow of air carries combustion heat away from the engine. Overheating and engine s[...]
-
Page 19
W a t e r P u m P O P e r a t O r ' s m a n u a l 19 NOTE The throttle cable remains assembled to the engine cover and the spark plug lead and grommet remain installed. IMPOR T ANT DO NOT use a metal scraper to remove dirt from the cylinder ns. 3. Use the brush to remove dirt from the cylinder ns. 4. Remove grass and leaves from the grid[...]
-
Page 20
20 Exhaust Port Cleaning Level2. T ools requir ed: Cross-head Screwdriver , 3 & 4 mm Hex W rench, W ood or plastic scraper Parts Requir ed: As needed: Heat Shield 1. Remove engine cover . See “Cleaning Cooling System” for step by step instructions.. 2. Place piston at top dead center . Remove mufer (A) and heat shield (B). 3. Use a wo[...]
-
Page 21
W a t e r P u m P O P e r a t O r ' s m a n u a l 21 c a r b u r e t o r a d j u s t m e n t Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break- in period your engine performance will increase and exhaust emissions will stabilize. Idle speed [...]
-
Page 22
22 (Non Emissions Models W ithout Limiter Caps) T ools Required: Screwdriver , T achometer (ECHO P/N 90051 130017). 1. Before adjusting the carburetor, clean or replace the air lter and spark arrester screen. 2. Fill pump housing with clean water . 3. Start engine and run for several minutes to reach operating tem - perature. Idle Speed Adjustme[...]
-
Page 23
W a t e r P u m P O P e r a t O r ' s m a n u a l 23 A B C D E F G p u m p c a s I n g Should the pump become clogged with debris: 1. Disconnect the spark plug wire. 2. Remove the prime port plug (A) and drain plug (B) from the pump housing (C) and drain the water from the pump. 3. Remove the four bolts (D) securing the pump housing to the pum[...]
-
Page 24
24 t r o u b l e s h o o t I n g DANGER Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result. T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r Pk c e h Cs u t a t Se s u a C[...]
-
Page 25
W a t e r P u m P O P e r a t O r ' s m a n u a l 25 No water delivered or not enough water delivered •Pump not primed •Speed too low •Suction line clogged •Suction lift too high •Air leak in suction line •Fill pump body with water. •Pump should operate at 5600-6300 rpm. •Clean suction opening. •Locate pump closer to water. ?[...]
-
Page 26
26 7. Remove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, 2-stroke engine oil into the cylinder through the spark plug hole. A. Place a clean cloth over the spark plug hole. B. Plug the recoil starter handle 2-3 times to distribute the oil inside the engine. C. Observe the piston location through the spark plug hole. Pull the starter han[...]
-
Page 27
W a t e r P u m P O P e r a t O r ' s m a n u a l 27 s p e c I f I c a t I o n s MODEL ---------------------------------------------------- WP-1000 Length ------------------------------------------------------- 310 mm (12.2 in.) W idth -------------------------------------------------------- 226 mm (8.9 in.) Height ----------------------------[...]
-
Page 28
28 ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited W arranty , provides to the original purchaser that this ECHO product is free from de fects in material and workmanship . Under normal use and maintenance from date of purchase, ECHO agrees to repair[...]
-
Page 29
W a t e r P u m P O P e r a t O r ' s m a n u a l 29 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES ?[...]
-
Page 30
30 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small of f-road engine (SORE). New equi[...]
-
Page 31
W a t e r P u m P O P e r a t O r ' s m a n u a l 31 n o t e s[...]
-
Page 32
CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T . ECHO, INCORPORA TED 400 Oakwood Road Lake Zurich, IL 60047-1564 www .echo-usa.com 001001/999999 501001/599999 W15103001001/W15103999999 DEALER? Call 1-800-432-ECHO 1-800-432-3246 or www .echo-usa.com s e r v I c I n g I n f o r m a t I o n p a r t s / s e r I a l n u m b e r Genu[...]