Go to page of
Similar user manuals
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Dolmar PS7300HS-45, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Dolmar PS7300HS-45 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Dolmar PS7300HS-45. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Dolmar PS7300HS-45 should contain:
- informations concerning technical data of Dolmar PS7300HS-45
- name of the manufacturer and a year of construction of the Dolmar PS7300HS-45 item
- rules of operation, control and maintenance of the Dolmar PS7300HS-45 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Dolmar PS7300HS-45 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Dolmar PS7300HS-45, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Dolmar service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Dolmar PS7300HS-45.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Dolmar PS7300HS-45 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
1 Instruction Manual Original Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! http://www .dolmar .com PS-6400, PS-6400 H PS-7300, PS-7300 H PS-7900, PS-7900 H[...]
-
Page 2
2 T able of contents Page Packing ................................................................................ 2 Delivery inventory .............................................................. 3 Symbols ............................................................................... 3 SAFETY PRECAUTIONS General precautions ....................[...]
-
Page 3
3 STOP 1 4 5 6 7 3 2 8 Delivery inventory 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench 6. Offset screwdriver 7. Screwdriver for carburetor adjustment 8. Cylinder Þ n cleaner 9. Instruction manual (not shown) In case one of the parts listed should not be included in the delivery inventory , please consult you[...]
-
Page 4
4 4 5 6 7 1 2 3 1 SAFETY PRECAUTIONS Intended use Power chain saws This power chain saw may be used only for sawing wood out of doors. It is intended for the followung uses depending on its class: - Professional and mid-class: Use on small, medium and large trees: felling, limb removal, cutting to length, thinning. - Hobbyklasse: Occasional use on [...]
-
Page 5
5 6 5 7 9 8 Fuels / Refuelling - Stop the engine before refuelling the chain saw. - Do not smoke or work near open Þ res (5). - Let the engine cool down before refuelling. - Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. Always wear protective gloves when refuelling. Frequently[...]
-
Page 6
6 Kickback - When working with the chain saw dangerous kickbacks may occur . - Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). - This causes the saw to be thrown back toward the user with great force and out of control. Risk of injury! In order to prevent kickback, follow these [...]
-
Page 7
7 - Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped. For this reason use the lower edge of the bar whenever possible. The chain saw will then be pushed away from y[...]
-
Page 8
8 SERVICE T ransport and storage - When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inadvert- ent start of the chain. - Never carry or transport the chain saw with the chain running. - When transporting the chain saw over long distances the guide bar protection cover (delivered with[...]
-
Page 9
9 Denomination of components 1 Handle 2 Filter hood 3 Filter hood clip 4 Tubular handle 5 Hand guard (release for chain brake) 6 Muf ß er 7 Spike bar 8 Chain tensioning screw 9 Retaining nuts 10 Chain catch 11 Sprocket guard 12 Identi Þ cation plate 13 Starting valve (option) 14 Starter grip 15 Adjusting screws for carburetor 16 I/STOP-switch 17 [...]
-
Page 10
10 5 7 6 4 5 1 2 3 Lift the chain ( 6 ) over the sprocket ( 5 ). Using your right hand, guide the chain into the top guide groove on the guide bar ( 7 ). CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Position the guide bar ( 4 ) and push against the sprocket ( 5 ) as shown by the arrow . M[...]
-
Page 11
11 2 13 3 11 12 6 8 9 10 Guide the chain over the chain catch ( 9 ). Pull the guide bar as shown by the arrow to take the slack out of the chain, so that it comes up to the bottom edge of the guide bar ( 10 ). Pull the chain ( 6 ) around the sprocket nose ( 8 ) of the guide bar in the direction of the arrow . G H Tightening the saw chain Slightly l[...]
-
Page 12
12 ST OP 2 13 1 2 1 Checking the chain tension The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. While doing so the chain brake must be released. Check the chain tension frequently - new chains tend to get longer during use! When checking the chain tension the eng[...]
-
Page 13
13 Chain oil Use an oil with adhesive additive for lubricating the chain and guide bar . The adhesive additive prevents the oil from being ß ung off the chain too quickly . We recommend the use of chain oil which is bio-degradable in order to protect the environment. The use of bio-degradable oil may even be required by local regulations. The chai[...]
-
Page 14
14 Refuelling FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. The engine must be switched off! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel or oil tank. Unscrew the cap and Þ ll the tank with fuel (fuel/oil mixture) or chain oil as the case may be. Fill up to the bottom edge of t[...]
-
Page 15
15 1 2 3 Checking the chain lubrication Never work with the chain saw withoute suf Þ cient chain lubri - ca tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see „Starting the engine?[...]
-
Page 16
16 Starting the engine Start the chain saw only after having assembled it com- pletely and inspected. Move at least 3m away from the place where you fuelled the saw . Make sure you have a good footing, and place the saw on the ground in such a way that the chain is not touching anything. Engage the chain brake (lock). Hold the tubular handle tightl[...]
-
Page 17
17 D Adjusting the carburetor CAUTION: Carburetor adjustment may only be done by a specialist DOLMAR service centre! Only adjusting screw (S) can be manipulated by the user . If the saw chain moves in idle (i.e. without the throttle being pressed) , it is imperative to correct the idle speed! Do not adjust the idle speed until after complete assemb[...]
-
Page 18
18 E Working in winter In order to prevent carburetor icing in conditions of low tempe- rature combined with high humidity , and below + 5°C in order to get up to operating temperature faster , heated air can be taken from the cylinder . Remove the Þ lter hood (see „Cleaning air Þ lter“) Remove the insert ( 10 ) and insert it as shown in pos[...]
-
Page 19
19 The sharpening angle of 25° must be identical for all cutters! Different angles result in a roughly , irregularly running chain, increase wear and tear and cause chain beakage. The front rake 60° of the cutter results from the cut depth of the round Þ le. If the proper Þ le is used in the right manner, the correct front rake will be obtained[...]
-
Page 20
20 1 2 Files and how to work with them Sharpen using a special Þ le holder with a saw chain round Þ le. Normal round Þ les are not appropriate for this work. See „Accessories“ for the order number . File the Þ rst cutter half with a 5.5 mm dia. round saw-chain Þ le, then switch to a 4.8 mm dia. Þ le. The Þ le should cut only when pushed [...]
-
Page 21
21 8 10 11 7 5 4 5 1 6 7 2 3 Cleaning the brake band and sprocket interior CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „Replacing the spark plug“) . Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it completely and in[...]
-
Page 22
22 12 16 15 13 17 Replacing the saw chain CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare-parts list) ! Check the sprocket before mounting a new chain. Worn out sprockets ( 12 ) may damage the new chain and must therefore be replaced. Remove the sprocket guard ( 1 ) (See „PUTTING INTO OPE- RA TION“ [...]
-
Page 23
23 3 5 4 CAUTION: T o prevent eye injury , always wear eye protection when cleaning the Þ lter with compressed air! Do not use fuel to clean the air Þ lter . Unhook the Þ lter hood clips ( 1 ) with the combination tool and remove the Þ lter hood ( 2 ). Pull out the choke ( 3 ) to prevent dirt particles from getting into the carburetor . Unhook [...]
-
Page 24
24 10 Replacing the spark plug CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. W ear protective gloves! The spark plug must be replaced in case of damage to the insulator , electrode erosion (burn) or if the electrodes[...]
-
Page 25
25 11 Replacing the starter cable / Replacing the return spring Unscrew three screws ( 1 ). Remove fan housing ( 2 ). NOTE: The screws ( 1 ) are secured against falling out of the housing. CAREFUL! Injury hazard! Do not unscrew screw (5) if the return spring is under tension. If the starter cable is to be replaced although it is not broken, it will[...]
-
Page 26
26 13 15 16 14 Cleaning the cylinder area Remove the Þ lter hood and air Þ lter . Remove the spark plug cap and unscrew the spark plug. Press in the starting valve and activate the chain brake. Push the cable cutout and ignition cable out sideways. Unscrew the two rearmost screws on the cover . Unscrew the screws on the handguard pivot and remove[...]
-
Page 27
27 Instructions for periodic maintenance T o ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be pe r- formed regularly . Guarantee claims can be recognized only if this work is performed regularly and properly . Failure to perform the prescribed maintenance work can lead to acci[...]
-
Page 28
28 Spare parts Reliable long-term operation, as well as the safety of your chain saw , depend among other things on the quality of the spare pa rts used. Use only original DOLMAR parts, marked Only original spare parts and accessories guarantee the highest quality in material, dimensions, function and safety . Original spare parts and accessories c[...]
-
Page 29
29 15 10 11 9 16 4 8 7 6 5 13 20 21 22 23 24 27 25 1 2 3 12 14 10 11 17 28 Extract from the spare parts list Use only original DOLMAR parts. For repairs and replacement of other parts, see your DOLMAR service centre. Pos. DOLMAR-No. Qty . Denomination 1 415 038 655 1 Sprocket nose bar 38 cm (15“) 415 045 655 1 Sprocket nose bar 45 cm (18“) 415 [...]
-
Page 30
30 EU Conformity Declaration The undersigned, T amiro Kishima and Rainer Bergfeld, as authorized by DOLMAR GmbH, declare that the DOLMAR machines, T yp: 038, 039, 040 Chain saw EU prototype test certi Þ cate No. PS-6400 (040) 481 1004.1 1012 PS-7300 (039) 481 1004.1 1012 PS-7900 (038) 481 1004.11012 manufactured by DOLMAR GmbH, Jenfelder Str . 38,[...]
-
Page 31
31[...]
-
Page 32
32 Form: 995 701 221 (2012-06 GB) 106 Speci Þ cations subject to change without notice DOLMAR GmbH Postfach 70 04 20 D-22004 Hamburg Germany http://www .dolmar .com To Þ nd your local distributor, please visit www .dolmar .com[...]