Deutsche Telekom 704PC manual

===! T § Deutsche T elekom User Guide T -Eumex 704PC LAN. Experience High- speed Inter net A ccess for the Entire Ne twor k with T-DSL.[...]

Before Y ou Install or Operate Y our Eumex 704PC LAN... … please mak e sure you read t he instructions in this user guide. The la w requires us t o inform you about important safety precautions, both f or your own saf ety and to av oid damage to your equipment. If you ignore this guide , Deutsche T elek om will not accept any liability for damage[...]

Symbols Used General note Impor tant safety precautions Lif t the handset Replace the handset Hold your conv ersation Dial telephone number or select code digit Y ou hear an acknowledgement t one Y our telephone rings 3-par ty conference Press t he R-key (aka t he flash or enquir y key) Use the star k ey to activ ate or deactivat e a featur e Use t[...]

[...]

Contents General .............................................................................................................1 A W ord of W elcome ..................................................................................................................1 The F eatures of the Eumex 704PC LAN .................................................[...]

Contents D TMF P ost-dialling ............................................................................................................. ....27 Malicious Call Identification (MCID) ....................................................................................27 Calling Y our T -NetBox .......................................................[...]

Contents Activating/Deactiv ating Call Data Recording ....................................................................51 Activating/Deactiv ating Call T ransfer (ECT) .......................................................................52 Call T ransfer in a Communications System ...............................................................[...]

Contents Home Network .................................................................................................87 Installation ...............................................................................................................................87 Data T ransfer (Sharing and Mapping Drives)..........................................[...]

1 General The Eume x 704PC L AN is an ISDN communications system enabling you t o connect up to f our analogue devices to a basic ISDN connection. In addition the Eumex 704PC LAN has an Ethernet 10BaseT network with f our por ts. One of the Ethernet ports is used to make dir ect connections to T -DSL, while the remaining thr ee can be used to conne[...]

2 General The Features of the Eumex 704PC LAN • Call waiting • Call pick -up from t erminals and answerphones • Aut omatic callback ("on no reply" and "on busy") • CLIP (display of calling line number) on analogue t erminals • Four Ethernet 10BaseT ports (one wired for T -DSL) • USB interface to PC • T -DSL connect[...]

3 General Supported ISDN Features • Call waiting • Call forwarding ("immediately ," "on busy" and "af ter a specified time") • 3-par ty conference (tw o 3-par ty conferences can tak e place simultaneously) • Enquir y calls • Callback on busy (CCBS) • Callback on no reply (CCNR) • T oggling • Multiple su[...]

4 General Safety Precautions Do not open the housing. Unauthorised opening of the housing and impr oper repairs can endanger the user . In addition, the warranty is in validated. Do not continue using damaged or defective plugs or A C adapters with defective housings as these could cause electric shock s. Replace these components immedi- ately with[...]

5 Mounting and Commissioning Scope of Delivery Check to mak e sure that the contents of t he package are comple te: • 1 Eumex 704PC LAN ISDN communications system • 1 plug-in A C adapter • 1 ISDN connector cable • 1 USB connector cable f or PC • 1 CD-ROM with Windows 98/Me/2000/XP installation sof tware • 1 Eumex 704PC LAN user guide (t[...]

6 Mounting and Commissioning What Does the Eumex 704PC LAN Require? Cer tain prerequisit es must be met for the smooth installation and oper ation of the Eumex 704PC LAN, the configuration sof tware and t he T eledat RVS- COM communi- cations package: • Y ou must have a basic Eur o-ISDN connection with a network terminator (NTB A) as supplied by [...]

7 Mounting and Commissioning Mounting and Installation Sequence The Eume x 704PC L AN consists of various components. This User Guide first describes how to mount t he communications system and how t o connect terminals such as telephones. Y ou can subsequently operate the devices. Howev er , we recommend that you configure t he Eumex 704PC LAN acc[...]

8 Mounting and Commissioning Mounting Location The ambient operating t emperature for the Eume x 704PC L AN must not be lower than +5 ° C or higher than +40 ° C. For this reason, do not mount the Eume x 704PC L AN • above or in fr ont of sources of heat (e.g. r adiators), • in direct sunlight, • behind cur tains, • in small, un ventilated[...]

9 Mounting and Commissioning Connect the Eumex 704PC LAN to a separat e 230 V ~ mains circuit. This pr events the communications system fr om being af fect ed by possible shor t circuits in any other household equipment. W e recommend you t o install a surge prot ector f or protection against sudden high voltages such as those some times occurring [...]

10 Connecting De vices Connection Diagram LAN 1 LAN 2 LAN 3 T-DSL LAN 4 Power T-ISDN B-Kanal 1 B-Kanal 2 Message Verbindungs- daten Router USB LAN 1 LAN 2 LAN 3 T-DSL / LAN 4 Do not connect the Eumex 704PC LAN during a thunderstorm, as this could lead t o you getting an electric shock. L ay all the cables so that t hey cannot be walk ed on or tripp[...]

11 Connecting De vices Regulations permit the general public t o connect the Eumex 704PC LAN to the Deutsche T elekom ne twork. Y ou can thus connect the Eumex 704PC LAN yourself if the following conditions ar e met: • The de vice may only be connected t o a basic Euro-ISDN connection. Do not under any circumstances connect it t o lines or equipm[...]

12 Connecting De vices Connecting Analogue T erminals to the Eumex 704PC LAN Y ou can connect up to f our analogue terminals to y our communications system. W e recommend you to deploy terminals that feature DTMF dialling and a flash func- tion. T erminals with pulse dialling cannot per form functions requiring the R-k ey (e.g. enquir y calls), or [...]

13 Connecting De vices Connection to the 230V mains supply is not danger ous, providing y ou adhere strictly to the f ollowing instructions. Danger! Under no circumstances should you commission or continue operating the device if the A C adapter is damaged. F ailure to obser ve this could result in loss of life due to an electric shock. • L ay th[...]

14 Connecting De vices Socke ts The operation of a communications syst em can be impaired by interference in the power supply caused by ot her equipment, especially photocopiers, laser printers, electric typewriters, air conditioning, f an heaters, vacuum cleaners and refrigerat ors. For this r eason, please: • Connect the Eumex 704PC LAN to a so[...]

15 Connecting De vices Besides the Eumex 704PC LAN, you can operate additional ISDN t erminals (e.g. ISDN telephones) on the NTB A. T o simplify the connection of additional devices, y ou will find an ext ernal S 0 por t on the lower side of the Eumex 704PC LAN. This is the looped-through S 0 bus fr om the NTBA. Y ou can use the ext ernal S 0 por t[...]

16 Connecting De vices Setting the Dialling Mode for the Analogue T erminals The communications syst em automatically recognises analogue t erminals with D TMF dialling and a flash function; you do not hav e to set anyt hing. Analogue terminals with pulse dialling must be enr olled before t hey can be used: pick up the handset, dial an y digit othe[...]

17 Commissioning The f ollowing default settings and f eatures are active on deliv er y: • The PIN is se t to "0000." • External incoming calls ar e signalled on all connected terminals. • External line access: all t erminals have int ernational access rights. • When you lift the handset, you hear an ext ernal dialling tone (= aut[...]

18 T elephoning Accepting Calls In order for y ou to be able t o use all the features pr ovided by y our telecommunica- tions system, the terminals must be set to DTMF dialling with a flash function. T ermi- nals with pulse dialling cannot perform functions requiring the R-key , the star or the hash k eys. Y our telephone rings: int ernal or extern[...]

19 T elephoning An internal call is a call made t o another subscriber on the same Eumex 704PC LAN. Automatic ext ernal line seizure (the default setting on delivery): Lif t the handset. Y ou hear an ext ernal dialling tone . Press t he R-key . Dial the desired int ernal number (11 to 14). Y ou hear internal call signalling: t he call is signalled [...]

20 T elephoning Making Calls Using Speed Dialling The Eume x 704PC L AN saves up t o 100 speed- dialling numbers (or "destinations"). Every internal subscriber can be granted the right t o use these speed-dialling num- bers. (Y ou edit the relev ant settings in the configuration mode .) Lif t the handset. Y ou hear an internal or e xterna[...]

21 T elephoning Gespräch w eiter geben L et’s sa y you want t o transfer a call int ernally or externally . Dial the internal sub- scriber’s number or 0 and the ext ernal number , then replace the handset. T he sub- scriber’s telephone signals the call . When he lif ts the handset he accepts the call . Y ou are having a con versation. Press [...]

22 T elephoning Gespräch weitergeben T ransferring Calls with an Announcement Y ou want to tr ansfer a call int ernally or externally , but you first want t o speak to the other subscriber . Y ou are having a con versation. Press t he R -k ey . Y ou hear the internal dialling tone . Dial the internal number or 0 f ollowed by t he external number .[...]

23 T elephoning Using the Eumex 704PC LAN you can toggle betw een two subscribers, i.e. speak to them alternat ely . They can be int ernal or external subscribers. Ext ernal subscribers who are on hold hear an announcement from t he exc hange. Y ou are having a con versation and want to mak e an enquir y call to a second sub- scriber . Press t he R[...]

24 T elephoning Speaking with T wo Subscribers Simultaneously (3-par ty Conference) Used on a multi-terminal connection the Eume x 704PC L AN enables two 3-par ty con- ferences t o be held simultaneously. One int ernal and two ext ernal subscribers can par ticipate in a confer ence. One B-channel must be free in order f or a conference t o tak e pl[...]

25 T elephoning Y ou can pick up an ext ernal call signalled on another terminal on t he Eumex 704PC L AN: Lif t your handset. Select the code digit 4. Pr ess the R-key first in the case of aut omatic external line seizure. Have y our conversation. Picking up Calls b 4 c Y ou can pick up a call from an analogue answerphone e ven if it has already s[...]

26 T elephoning Automatic Callback on No Reply (CCNR) If the ISDN Completion of Calls on No Reply service is available, y ou can also make a callback request t o contact a free subscriber . The pr ocedure is the same as for a busy subscriber . Y ou have dialled an e xternal number , but the subscriber does not lift the handset. Select the code digi[...]

27 T elephoning DTMF P ost-dialling D TMF post- dialling is only possible during external calls when, for example, an aut o- matic announcement prompts you t o post-dial digits and symbols (1 to 0, * and #), during fax polling, during a remot e answerphone enquir y , or when communicating with a voice mailbo x or other application. Ther e is an ext[...]

28 St a ying in T ouc h Call Forwarding Y ou can forward calls from an int ernal to an ext ernal terminal , or from one internal t o another internal t erminal. Depending on the configur ation, the call is forwarded in the Eumex 704PC LAN or in the exc hange (where a charge is incurr ed). In order to use internal call f or warding, the "Call f[...]

29 St a ying in T ouc h •" Immediately ": code digits 21 •" After a set time ": code digits 61 •" On busy ": code digits 67. Press t he star ke y . Enter the call f or warding destination number: an internal number (only if call f or ward- ing in the Eumex 704PC LAN is active), or an ext ernal number without a le[...]

30 St a ying in T ouc h Accepting or Rejecting Call W aiting Y ou are having a con versation and an ext ernal subscriber calls. The call is signalled on your terminal b y means of a call-waiting tone . Internal callers alwa ys hear a busy tone when you ar e having a conv ersation. Y ou have the f ollowing options: 1. Y ou can terminat e the current[...]

31 St a ying in T ouc h If you want t o have a con versation without being disturbed by any further callers, you can activate call-w aiting prot ection for the line t o which your terminal is connect ed. Any further callers then hear a busy tone. Call-waiting prot ection remains active until it is deactiv ated again. Lif t the handset. Press t he h[...]

32 Special Se ttings/F eatures Charge Accounts In the configuration mode you can assign e ver y internal subscriber a char ge limit (charge account). When the amount se t is reached during a call, t he call will either be disconnected (if advice of char ge during the call is active) or complet ed (if advice of charge at the end of t he call is acti[...]

33 Conf iguration via T elephone Y ou can edit the presettings and configur e the Eumex 704PC LAN according to your personal requirements. T here are thr ee ways of doing t his: you can use a PC and menus (see the chapt er entitled "Configuring the System" on p . 66), a connected tele- phone (only possible with DTMF telephones), or the re[...]

34 Conf iguration via T elephone Starting the Configuration Mode T o star t the configuration mode: Lif t the handset. Press t he R-key (only in the case of automatic ext ernal line access). Y ou hear an internal dialling t one. Select the code digit 8. Press t he star ke y . Enter your PIN (t he default setting on delivery is 0000). Press t he has[...]

35 Conf iguration via T elephone Y ou require a personal identification number (PIN) t o star t the configuration mode. The def ault setting on deliver y is 0000. W e recommend you t o change this PIN and k eep the new one in a safe and secr et place. T o edit the PIN: Lif t the handset. T he configuration mode is active and you hear a special int [...]

36 Conf iguration via T elephone Storing T elephone Number s (MSNs) In order for incoming calls t o be signalled on specific terminals, y ou have to sa ve the MSNs allocated t o you by Deutsche T elek om in the Eumex 704PC LAN. The MSNs are sav ed without an area code. P lease mak e a note of the sav ed MSNs in the table on p. 37. Saving T elephone[...]

37 Conf iguration via T elephone In order for incoming calls t o be signalled on specific terminals, y ou have to pr ogram call assignment. Here you specify whic h terminal rings when a cer tain MSN is called. Y ou do this by assigning ev er y external number (MSN) t o one or more internal lines, which then signal the call . Please mak e a note of [...]

38 Conf iguration via T elephone Reset the Call Assignment T o reset the call assignment, proceed as f ollows: Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 905. Press t he hash ke y . Y ou hear a positive acknowledgement tone . Replace the handset. Incoming ext ernal ca[...]

39 Conf iguration via T elephone When this setting is active , you have t o dial 0 befor e dialling an external number . Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 050. Press t he hash ke y . Y ou hear a positive acknowledgement tone . Replace the handset. Y ou now ha[...]

40 Conf iguration via T elephone Number Busy With this setting y ou can specify whether incoming calls for an MSN during an e xter- nal call are signalled as call waiting b y ringing on other telephones, or whet her the caller hears a busy tone. Activating "Number Busy" If you want the second caller t o hear a busy tone when the MSN is bu[...]

41 Conf iguration via T elephone Y ou can configure a device type (e .g. fax, answerphone) f or every internal line so that the Eumex 704PC LAN can manage the respective de vices correctly . This ensures that fax transmissions ar e not interrupted b y call-waiting tones, f or instance. Y ou configure the device types f or the internal lines as f ol[...]

42 Conf iguration via T elephone External Line Access Y ou can set ext ernal line access to one of five le vels for ev er y internal line. If a sub- scriber dials an ext ernal number for which that line has no access rights, he hears the busy tone . The emergency numbers can alwa ys be dialled (see the section below). Y ou set ext ernal line access[...]

43 Conf iguration via T elephone Y our Eumex 704PC LAN can save up to t hree emergency numbers. These numbers can always be dialled fr om every telephone, independent of the e xternal line access rights that otherwise exist. Y ou save the emer gency numbers as follows: Lif t the handset. T he configuration mode is active and you hear a special int [...]

44 Conf iguration via T elephone Storing Numbers for Speed Dialling Y our Eumex 704PC LAN can save up to 100 t elephone numbers, which you can then dial conveniently using the speed-dialling code digits 00 to 99. Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 61. Select a[...]

45 Conf iguration via T elephone Internal lines with outw ard restrict ed or no external line access can (in t he default set- ting) can still use speed-dialling number s to dial destinations falling outside t heir ext ernal line access levels. If you w ant to pre vent this, you can block speed dialling as follows: Lif t the handset. T he configura[...]

46 Conf iguration via T elephone Programming a T elephone Number (MSN) for T ransmission Y ou can program whic h of the MSNs is to be transmitt ed to the called subscriber . If you do not progr am anything, the first MSN for whic h your telephone signals calls is transmitted (see t he chapter entitled "Call Assignment"). Y ou must pr ogra[...]

47 Conf iguration via T elephone Y ou can only cancel the restriction of the t elephone number display f or all lines simul- taneously: Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 31. Press t he hash ke y . Y ou hear a positive acknowledgement tone . Replace the handse[...]

48 Conf iguration via T elephone Charge per Unit of Time Enter the c harge per unit of time for call-charge registr ation in cents, e.g. 0006 (the default setting is 0.06 eur os). Y ou can edit the currency under "CAPI-ControlEinst el- lungen ( Settings) Gebühreneinst ellungen (Charge settings) Währung (Currency)." Lif t the handset.[...]

49 Conf iguration via T elephone Y ou can set a charge limit (c harge account) for e ver y internal line, whic h you can then activate and deactiv ate as the need arises. When t he limit has been reached, no fur- ther outgoing ext ernal calls are possible on this line (the subscriber hears a busy tone). T he pre-programmed emergency numbers can sti[...]

50 Conf iguration via T elephone Managing Call Forwarding Y ou can specify whether call forwarding f or external calls is t o tak e place in the Eumex 704PC LAN (= the default setting) or in the t elephone exc hange. Both proce- dures hav e cer tain advantages. Call forwarding in the ex change must be ordered from Deutsche T elek om. Call forwardin[...]

51 Conf iguration via T elephone Y ou can use the following pr ocedure t o delete all call f or warding: Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 906. Press t he hash ke y . Y ou hear a positive acknowledgement tone . Replace the handset. Deleting All Call Forwardin[...]

If the ISDN ser vice ECT is available in t he exc hange, you can activat e and deactivate it as required: Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 990. Select the code digits 71 to activ ate or the code digits 70 to deactiv ate ECT . Press t he hash ke y . Y ou hear[...]

53 Conf iguration via T elephone Activating/Deactiv ating T -NetBox Signalling Y ou can activate and deactiv ate the LED ("Message" LED) t hat signals messages wait- ing and faxes r eceived: Lif t the handset. T he configuration mode is active and you hear a special int ernal dialling tone . Select the code digits 990. Select the code dig[...]

54 Conf iguration via T elephone Y our Eumex 704PC LAN suppor ts the "SMS in a fixed-line network" function. T his function can only be used on analogue telephones that e xplicitly suppor t the "SMS in a fixed-line network" f eature. For correct oper ation of this ser vice, the SMS Service Centre telephone number must be configu[...]

55 Conf iguration via T elephone Y ou can deactivate or dele te all activat ed features and activ ate all def ault settings instead. T his resets your syst em to the deliv er y state (i.e. the f actory settings are active again). Resetting the Communications Syst em The secr et PIN is reset t o 0000. Lif t the handset. T he configuration mode is ac[...]

56 R emote Conf iguration F er nk onf iguration If you decide not to configur e your Eumex 704PC LAN yourself, you can have it con- figured remot ely by T eleSer vice for a fee . Call T eleSer vice for advice, and list your configuration requir ements. T eleSer vice will then remotely configure y our communi- cations system. Please follow the T ele[...]

57 The PC Sof tware The communications software supplied enables you t o use the ISDN data transfer serv- ice, class 3 and 4 fax and e-mail transmission and reception, a mailbo x, an answer- phone function and Internet applications on up t o four PCs via the USB or one of the Ethernet 10BaseT ports. Y ou can use network functions on the PCs as soon[...]

58 The PC Sof tware System Prerequisites The syst em prerequisit es for the installation of the Eume x 704PC L AN sof tware on your PC are as f ollows: • IBM- compatible PC with a hard- disk and CD -ROM drive • CPU speed of 233 MHz or fast er • Minimum of 64 MB RAM • Microsoft Windows 98/Me/2000/XP • One free USB or Etherne t 10BaseT por [...]

59 The PC Sof tware On the CD -ROM supplied you will find the f ollowing sof tware: • The Eumex 704PC LAN system software contains the sof tware necessary for operating the Eume x 704PC L AN including the CAPI , C API Port , CAPI Control and T API drivers, as well as the configuration pr ogram for pr ogramming the com- munications system.. • T [...]

60 Inst alling the Sof tw are Installing the Software and Configuring Internet Access Before installing the software, you must ensure that any e xisting ISDN instal- lation on your PC is deactivat ed or uninstalled. No other CAPI drivers must be installed, because this could result in conflicts between the various C API drivers.If you want t o conn[...]

61 Inst alling the Sof tw are Note The above installation screens will only appear if y ou connected your PC directly to the Eumex 704PC LAN via the USB por t before installing the software. If the connection is via Ethernet, or if the PC has not yet been connect ed, the following screen will appear . (This screen only appear s automatically if Aut[...]

62 Inst alling the Sof tw are Follow the instructions in the installation pr ogram. If the installation wizard reports finding newer files, please do not over write them. T o connect your PC to the Eume x 704PC L AN, select the desired port. Please not e that your PC must have a ne twork card in order t o be able to connect to a LAN por t on the Eu[...]

63 Inst alling the Sof tw are 7. Depending on the following selection ("T - Online" or "Anderer Internet Service Pro vider " ( Other ISP )), an input screen may open in which y ou enter the access data obtained from your pr ovider . The input field names corr espond to the e xpressions used in the respectiv e docu- mentation. Th[...]

64 Inst alling the Sof tw are 8. Follow the instructions in the configur ation program. 9. On completion of the progr am, the access data is saved t o the Eumex 704PC L AN. When you now start an Internet browser (such as Ne tscape Communicator or Microsoft Internet Explorer), you will aut omatically be connected t o the Inter- net. 10. Disconnectin[...]

65 Star t the configuration software to edit the man y Eumex 704PC LAN settings. Access to t he configuration program is PIN-pr otect ed. In the default setting on deliv- er y , this PIN is 0000 (i.e. nought four times). This is the same as t he PIN you need to star t the configuration mode from a t ele- phone. Y ou can edit the PIN via the menu it[...]

66 Configuring the Eumex 704PC LAN Conf iguring t he Sy st em Star t the configuration software to edit the man y Eumex 704PC LAN settings. Access to t he configuration program is PIN-pr otect ed. In the default setting on deliv- er y , this PIN is 0000 (i.e. nought four times). T his is the same as the PIN you need to star t the configuration mode[...]

67 Conf iguring t he Sy st em T ype in the telephone numbers (MSNs) assigned to you f or your ISDN connection by Deutsche T elekom, wit hout an area code. Storing t elephone numbers (MSNs). Menu: External ISDN / T elephone numbers[...]

68 Conf iguring t he Sy st em Assign the connected t erminals one or more telephone numbers (MSNs). Ext ernal incoming calls for the corr esponding MSN will then be signalled on the assigned ter- minals. SMS in a fixed-line network Y our Eumex 704PC LAN suppor ts the "SMS in a fixed-line network" function. T his function can only be used [...]

69 Conf iguring t he Sy st em Settings Y ou can edit various settings f or each connected de vice. When the device is select ed, the optimum settings for t he respective device type will be select ed automatically (e.g. "Call waiting" -> "off " for fax es and modems). Notes: •The telephone numbers available f or transmissio[...]

70 Conf iguring t he Sy st em Call Forwarding The call f or warding input screen depends on t he type of call for warding select ed ("in the ex change" or "in the communications syst em"). Call forwarding in the communications system (Anrufweiterschaltung in der Anlage) When calls are to be f or w arded in the communications sys[...]

71 Conf iguring t he Sy st em Call forwarding in the exchange When calls are to be f or w arded in the ex change, y ou specify a call-forwarding desti- nation for incoming calls t o each of the enter ed MSNs. As opposed to call forwarding in the communications system, t he connection is not busy for the duration of call f or- warding, and t he othe[...]

72 Conf iguring t he Sy st em Settings Here you can edit y our communications system settings. T hese settings apply to all connected devices. Menu: Central data Please note In order for messages w aiting in your T -NetBox t o be indicated, the ISDN "MWI" ser vice must be available f or your ISDN connection. For the lat est details of thi[...]

73 Conf iguring t he Sy st em Emergency numbers The emer gency numbers entered here can alw ays be dialled, regar dless of the ext er- nal line access levels (see the "T eilnehmer int ern / Einstellungen" ( Internal sub- scribers / Settings) menu on p. 69).[...]

74 Conf iguring t he Sy st em Summar y In this screen you can see t he charges incurred b y a specific MSN in the left-hand col- umn, and the charges incurr ed by for a specific t erminal in the right-hand one. Y ou can edit the fact or , read out the current status from t he communications system, or reset the count er . Setting a charge limit T o[...]

75 Conf iguring t he Sy st em Call data records Call data records consist of inf ormation about the device (line), the busy t elephone number (MSN), the beginning and the end of the call , the telephone number called and the charges incurr ed.[...]

76 Menu: Speed dialling / Settings Conf iguring t he Sy st em The communications syst em can save up t o 100 telephone numbers (00 - 99) as speed-dialling codes. Depending on speed- dialling rights (see the "T eilnehmer intern / Einstellungen" ( Int ernal subscribers / Settings ) menu on p. 69), connected termi- nals can be used to call t[...]

77 Menu: Network / Rout er configuration Conf iguring t he Sy st em Here you can ent er the data for Int ernet access via the rout er . On your monitor (as opposed to the diagr am), the corresponding fields are filled in. This is the data y ou entered on installation. Y ou can edit this data: please note that any changes y ou make her e will af fec[...]

78 St ar ting a Prog ram f rom t he W indo ws T a skbar In the lower right-hand corner of the Windo ws taskbar you find the depict ed icon in the form of an LED for each of t he B- channels. The colour of the LEDs indicates t he CAPI status. The colours hav e the following meanings: red - deactivated yellow - no connection to device grey - connecti[...]

79 C API Control The C API Control program pr ovides you with compr ehensive information about an existing connection, and enables you t o edit a number of CAPI settings. Windows star ts this program aut omatically , and you can invok e it via the taskbar . For fur ther information about eac h of the available tabs, clic k on the Help button. Y ou [...]

80 Fla shLoad Y ou can update your Eume x 704PC LAN system sof tware yourself. T his may be nec- essar y when new featur es become available . Y ou can download the newest version from the Int ernet under the follo wing address: http://www.t elekom.de/f aq , where you click on "Endger äte und Downloads" ( Devices and Downloads ) in the n[...]

81 Fla shLoad Select the system software t o be loaded and open this file. Y ou see the software ver- sion information. When you use the F lashLoad f eature f or the first time, your PC operating syst em will install the necessar y sof tware modules. Y ou cannot use the "Next" button until this procedure has been comple ted.[...]

82 Fla shLoad Before t he upload procedure begins, the scr een depicted opens with important infor- mation about what to do during this pr ocedure. A monitoring screen k eeps you informed about the curr ent status of the upload. When the data transf er is complete, t he program is aut omatically terminated, and t he Eumex 704PC LAN restar ts.[...]

83 T eledat R V S - COM Basic Functions The T eledat RVS-COM sof tware package enables y ou to use all the ISDN services conveniently on y our PC. T eledat RVS- COM consists of the following modules: 1. RVS T ransferMaster is a file manager enabling fast and secure file tr ansfer , e.g. to colleagues in the field. 2. RVS F ax enables you to send fa[...]

84 T eledat R V S - COM 3. RVS T elefon acts as an ISDN telephone with answerphone on your PC. T o use this function, your PC must hav e a full- duplex soundcard. 4. RVS T erminal is a terminal emulation enabling your PC to establish connections t o ISDN mailbox es. 5. RVS VideoPhone establishes a connection t o a par tner with an RVS VideoP hone, [...]

85 W inPhone Basic Functions The con venient dialling wizard enables you t o plan and log telephone calls using a subscriber database. If a caller’s number is transmitt ed, he/she can be identified by means of the entr y in this database. User Interface For further information, please refer to the comprehensive help file ("Hilf e " ( He[...]

86 P ageMobil P ageMobil is a program that enables you t o send shor t messages. Basic Functions User interface For further information, please refer to the comprehensive help file ("Hilf e " ( Help ) menu item and the on-line help).[...]

87 Home N e tw ork Installation The installation of the Eume x 704PC LAN system sof tware fulfils all the pr erequisites for network oper ation. Ever y PC connected t o the system can be accessed as a net- work PC and can, in turn, access the other PCs in the ne twork or their hard disk drives if this is not restrict ed by personal settings. Please[...]

88 Home N e tw ork Sharing a Drive In order to shar e a drive (e.g. a partition of your hard disk or a built-in ZIP drive), click on that drive with the right-hand mouse butt on, select the "Sharing" tab, and grant the rights as desired. If the "Sharing" tab does not appear , you must first activate file and print sharing under [...]

89 Home N e tw ork Displaying the Netw ork Neighbourhood Double- click the "Network Neighbourhood" symbol on your PC deskt op to display all available PCs and t heir shared drives. Finding a Specific PC in the Network Y ou can find a specific PC in the network b y invoking a dialogue via the "F ind/Com- puter" item in the "[...]

90 The W eb Conf igurator Starting the Web Configurator The W eb Configurator enables you t o edit settings on the Eumex 704PC LAN using operating systems ot her than Windows. If the necessar y requirements ar e met, you can edit some of the settings using a sim- ple W eb browser (Micr osof t Internet Explorer , version 4.0 and up is recommended) r[...]

91 The W eb Conf igurator Click on "ISDN-Grundeinstellungen" ( ISDN - Basic settings ) to open the scr een depicted. If t elephone numbers (MSNs) have already been assigned t o the Eumex 704PC L AN, they will appear in the r espective fields. Rufnummer speichern Y ou can edit, delete or ent er new MSNs, then sav e them to the Eume x 704PC[...]

92 The W eb Conf igurator T -DSL Access Data Click on "T -DSL Zugangsdat en" ( T-DSL access data ) t o open the screen depict ed. If access data has already been sav ed to the Eume x 704PC L AN, it will appear in the respective fields. Y ou can edit the access data, then sav e it to Eumex 704PC LAN by clicking on the "Speichern"[...]

93 The W eb Conf igurator Click on "ISDN Zugangsdat en" ( ISDN access data ) to open the scr een depicted. If access data has already been sav ed to the Eume x 704PC L AN, it will appear in the respective fields. Y ou can edit the access data, then sav e it to the Eume x 704PC L AN by clicking on the "Speichern" ( Sav e ) button[...]

94 The W eb Conf igurator PPP Settings Click on "PPP Einstellungen" ( PPP settings ) t o open the screen depict ed. If settings have alr eady been made in the Eumex 704PC LAN (the diagram shows the default values), the y will appear in the respective fields. Y ou can edit the settings and sav e them to the Eume x 704PC L AN by clicking on[...]

95 The W eb Conf igurator Click on "Filt er " t o open the screen depicted. If se ttings have already been made in the Eumex 704PC LAN (the diagram shows the def ault values), they will appear in t he respective fields. Y ou can edit the settings and sav e them to the Eume x 704PC L AN by clicking on the "Speichern" ( Sav e ) bu[...]

96 The W eb Conf igurator Router Configuration Click on "Rout erkonfigur ation" ( Router configuration ) t o open the screen depict ed. If settings have alr eady been made in the Eumex 704PC LAN (the diagram shows the default values), t hey will appear in the respectiv e fields. Y ou can edit the configuration data and sav e it to the Eum[...]

97 The W eb Conf igurator Click on "Status" to open t he screen depicted. Y ou can edit the data and save it t o the Eumex 704PC LAN by clicking on the "Speichern" ( Sav e ) button. Status[...]

98 Ap pendix T echnical Specifications Mains power supply 230 V AC ; 50 Hz for the A C adapter Rat ed power 23 W Safety class 2 1 x Euro-ISDN external for the basic connection (looped through) DSS1 prot ocol Supply voltage 40 V ± 10% Range 100 m passive bus 4 analogue por ts Range 300 m P ermissible temperatures Stationar y , weatherproofed +5° C[...]

99 Ap pendix 3-party conference A call with one internal and tw o external subscribers. 10BaseT This is an Etherne t connection with a transfer r ate of 10 Mbit/ s. The connection is via twisted-pair cable . ADSL Stands for Asymmetric Digital Subscriber Line This is a transf er technology t hat uses the conventional copper - cable network t o reali[...]

100 Ap pendix Call-waiting protection Activat e call-waiting prot ection if you do not want t o be disturbed by other sub- scribers calling during a conversation. CAPI CAPI stands for "Common ISDN Application Programming Int er face." T his is a pro- gramming interface enabling Windows progr ams to utilise the functions of ISDN devices on[...]

101 Ap pendix Dial-up network Y our computer can use the Micr osof t Windows dial-up network facility t o connect to an Internet service provider via a modem. DTMF Stands for "dual t one multi-frequency ," also known as voice frequency dialling. T he dialling signals and control functions are tr ansmitted in the f orm of tones at various [...]

102 Ap pendix ISDN socke t The standar dised sock et for connecting ISDN devices in Deutsc he T elekom’s ISDN. LED Light emitting diode: an electronic component for visual signalling. MCID (Malicious Call Identification) An ISDN feature enabling malicious callers t o be identified in the telephone ex change. ML PPP Multilink point-to-point protoc[...]

103 Ap pendix PPP This stands f or "point-to-point protocol ," a network prot ocol used for connecting to t he Internet via a modem. Pulse dialling A dialling procedure in whic h the dialling signals are transmitt ed in the form of electri- cal impulses, as used by telephones wit h rotary dialling disks, for instance. Reset communications[...]

104 Ap pendix T -NetBox Digital answerphone with a fax buffer in Deutsche T elek om’s t elephone network. The Eumex 704PC LAN signals messages waiting in the T -NetBox. T oggle Switching back and f or th between two calls. Y ou can accept incoming calls even though you are alr eady making a call, or hav e an enquir y call with other par ticipants[...]

105 Ap pendix The f ollowing diagram shows the dur ation and intervals of the individual audio sig- nals and ringer cadences. Audio Signals / Ringer Cadences Audio signals Time in seconds Ring tone Busy tone Internal dialling t one External dialling t one P ositive acknowledgement tone Negative ackno wledgement tone Internal special dialling t one [...]

106 Ap pendix 3-par ty conference..................................24 A Anonymous calls .....................................46 Answerphone call ...................................25 Audio tones ............................................105 Automatic and manual e xternal line seizure .......................................................18 Autom[...]

107 Ap pendix M Malicious call identification (MCID) ....27 Manual ext ernal line seizure .................39 Mapping and sharing drives.................88 MCID ..........................................................27 Menu: Rufzuordnung / k ommend (Call assignment / Incoming) ...............68 Menu: Zentrale Dat en (Central data) ..72 Menu: Ent[...]

108 CE sign This device mee ts the requirements laid do wn in the following EC Dir ective: 1999/5/EC Directive on R adio Equipment and T elecommunications T erminal Equip- ment and the mutual acknowledgement of their conf ormity. The CE symbol on the equipment is pr oof of its conformity with the af orementioned Directive . The Declaration of Conf [...]

109 Ap pendix If repairs are unsuccessful , the purchaser ma y either request a reduction in t he pur- chase price or rescind the contr act and, insofar as Deutsche T elek om is accountable for the def ects, demand compensation. The pur chaser shall report any ascer tained defects to Deutsche T elek om without delay . Proof of w arranty must be pro[...]

110 Dealing with Faults Ap pendix If your system does not function as desir ed, first tr y getting it to work with t he help of the table below . The f ollowing notes ar e designed to help you deal with t he fault yourself: Problem Possible cause Solution System does not function AC adapt er not Check that adapt er is seated pr operly firmly seated[...]

111 Customer Service If you experience an y technical pr oblems with your communications syst em, call our T - Ser vice Hotline on 0180 51990 (please note that you will be c harged for y our call). Experienced technicians can also advise y ou on the operation of your syst em. Please have the serial number of t he communications system at hand when [...]

Important telephone numbers In case of faults: Sales enquiries: Please enter the telephone number when handing over the device. Published by: Deutsche T elekom A G Right to changes reserved. As of: 16.08.2002[...]