English dropdown-ico

Cypress AutoStore STK17TA8 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Cypress AutoStore STK17TA8, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Cypress AutoStore STK17TA8 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Cypress AutoStore STK17TA8. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Cypress AutoStore STK17TA8 should contain:
- informations concerning technical data of Cypress AutoStore STK17TA8
- name of the manufacturer and a year of construction of the Cypress AutoStore STK17TA8 item
- rules of operation, control and maintenance of the Cypress AutoStore STK17TA8 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Cypress AutoStore STK17TA8 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Cypress AutoStore STK17TA8, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Cypress service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Cypress AutoStore STK17TA8.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Cypress AutoStore STK17TA8 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    STK17T A8 128k X 8 AutoS tore™ nvSRAM with Real T ime Clock Cypress Semiconductor Corpora tion • 198 Champion Court • San Jose , CA 95134-1709 • 408-943-2600 Document #: 001-52039 Rev . ** Revised Marc h 02, 200 9 Features ■ nvSRAM Combined wi th Integrated Real T ime Clock Functions (RTC, W atchdog T imer , Cl ock Alarm, Power Monitor) ?[...]

  • Page 2

    STK17T A8 Document #: 001-52039 Rev . ** Page 2 of 23 Pinout s Figure 1. Pin Diagram - 48-PIn SSOP V SS A 14 A 12 A 7 A 6 DQ 0 DQ 1 V CC DQ 2 A 3 A 2 A 1 V CAP A 13 A 8 A 9 A 11 A 10 DQ 7 DQ 6 V SS A 0 NC 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 NC X 1 X 2 23 24 A 5 INT NC [...]

  • Page 3

    STK17T A8 Document #: 001-52039 Rev . ** Page 3 of 23 Absolute Maximum Ratings V oltage on Input Rela tive to Gr ound ................ –0.1V to 4.1V V oltage on Input Rela tive to V SS .........–0.5V to (V CC + 0.5V) V oltage on DQ 0-7 or HSB .....................–0.5V to (V CC + 0.5V) T emperature under Bias .............. ................. [...]

  • Page 4

    STK17T A8 Document #: 001-52039 Rev . ** Page 4 of 23 AC T est Conditions Input Pulse Levels ...... ............... .............. ........... ...... 0V to 3V Input Rise and Fall T imes ........... .............. .............. ..... < 5 ns Input and Output T iming Reference Levels ................ .... 1.5V Output Load .............. ..........[...]

  • Page 5

    STK17T A8 Document #: 001-52039 Rev . ** Page 5 of 23 RTC DC Characteristics Figure 4. RTC Recommended Component Configuration Symbol Parameter Commercial Industrial Unit s Notes Min Max Min Max I BAK RTC Backup Current — 300 — 350 nA From either V RTC ca p or V RTC b at V RTC ba t RTC Battery Pin V oltage 1.8 3.3 1.8 3.3 V T ypical = 3.0 V olt[...]

  • Page 6

    STK17T A8 Document #: 001-52039 Rev . ** Page 6 of 23 SRAM READ Cycles #1 and #2 Figure 5. SR AM READ Cycle #1: Address Controlled [3, 4, 6] Figure 6. SRAM READ Cycle #2: E and G Controlled [3, 6] Notes 3. W must be high during SRAM READ cycles. 4. Device is continuously selected with E and G both low 5. Measured ± 200mV from stead y state output [...]

  • Page 7

    STK17T A8 Document #: 001-52039 Rev . ** Page 7 of 23 SRAM WRITE Cycles #1 and #2 Figure 7. SRAM WRITE Cycle #1: W Controlled [7, 8] Figure 8. SRAM WRITE Cycle #2: E Controlled [7, 8] Notes 7. If W is low when E goes low , the outputs remain in the high-impedance state. 8. E or W must be ≥ V IH during address transitions. NO. Symbols Parameter ST[...]

  • Page 8

    STK17T A8 Document #: 001-52039 Rev . ** Page 8 of 23 AutoStore/Power Up Recall Figure 9. Au toStore /Power Up RECAL L Notes 9. t HRECALL starts from the time V CC rises abov e V SWITCH 10. If an SRAM WRITE has not tak en place since the last nonvolatile cycle, no STORE will take place 1 1. Industrial Grade De vices require 15 ms MAX. NO. Symbols P[...]

  • Page 9

    STK17T A8 Document #: 001-52039 Rev . ** Page 9 of 23 Sof tware-Controlled ST ORE/RECALL Cycle In the following table, the soft war e controlled STORE and RECALL cycle para meters are listed. [12, 13] Figure 10. Software STORE / RECALL Cycle: E CONTROLLED [13] Figure 1 1. Software ST ORE / RECALL Cycle: G Controlled [13] NO. Symbols Parameter STK17[...]

  • Page 10

    STK17T A8 Document #: 001-52039 Rev . ** Page 10 of 23 Hardware ST ORE Cycle Figure 12. Hardware STORE Cycle Sof t Sequence Commands Figure 13. Sof t Sequence Commands NO. Symbols Parameter STK17T A8 Units Notes Stan da r d Alternate Min Max 31 t DELA Y t HLQZ Hardware STORE to SRAM Disabled 1 70 μ s1 4 32 t HLHX Hardware ST ORE Pulse Width 15 ns [...]

  • Page 11

    STK17T A8 Document #: 001-52039 Rev . ** Page 1 1 of 23 MODE Selection E W G A 16 -A 0 Mode I/O Power Notes H X X X Not Selected Output High Z S tandby L H L X Read SRAM Output Data Active L L X X Write SRAM Input Data Active L H L 0x04E38 0x0B1C7 0x083E0 0x07C1F 0x0703F Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Output Data Output Data Outp[...]

  • Page 12

    STK17T A8 Document #: 001-52039 Rev . ** Page 12 of 23 nvSRAM Operation The STK17T A8 nvSRAM i s made up of tw o functional compo- nents paired in the same physical cell. These are the SRAM memory cell and a nonvolatile QuantumTrap cell. The SRAM memory cell operates like a standar d fast static RAM. Data in the SRAM can be transferred to the nonvo[...]

  • Page 13

    STK17T A8 Document #: 001-52039 Rev . ** Page 13 of 23 atile elements. Once a STORE cycl e is initiated, further memory inputs and outp ut s are disabled until the cycle is completed. T o initiate the Software STORE cycle, the following read sequence must be performed : 1. Read Address 0x4E38 V alid READ 2. Read Address 0xB1C7 V alid READ 3. Read A[...]

  • Page 14

    STK17T A8 Document #: 001-52039 Rev . ** Page 14 of 23 Figure 15. Current versus Cycle Time RTC Operations Real T ime Clock The clock registers maintain time up to 9,999 years in one second increments. The user can set the time to a ny calendar time and the clock automatically keeps track of days of the week and month, leap years, and cent ury tran[...]

  • Page 15

    STK17T A8 Document #: 001-52039 Rev . ** Page 15 of 23 Calibrati ng The Clock The RTC is driven by a quartz controlled oscillator with a nominal frequency of 32.768 KHz. Clock accuracy will depend on the quality of the crystal, specified (usually 35 ppm at 25 C). This error could equate to 1.53 minutes gain or loss per month. The STK17T A8 employs [...]

  • Page 16

    STK17T A8 Document #: 001-52039 Rev . ** Page 16 of 23 Interrupt s The STK17T A8 has a Flags register , Interrupt Register , and interrupt logic that can interrupt a microcontroller o r generate a power-up master reset sig nal. There are three potenti al interrupt sources: the watchd og timer , the power monitor , and the clock alarm. Each can be i[...]

  • Page 17

    STK17T A8 Document #: 001-52039 Rev . ** Page 17 of 23 RTC Register * A binary value, not a BCD value. 0 - Not implemented, reserved for future use. Default Settings of nonvolatile Calibrat ion and Interrupt registe rs from factory Calibration Reg ister=00h Interrupt Register=00h The User should configure to desired valu e at startup or during oper[...]

  • Page 18

    STK17T A8 Document #: 001-52039 Rev . ** Page 18 of 23 Register Map Det ail 0x1FFFF Real Time Clock – Y ea rs D7 D6 D5 D4 D3 D2 D1 D0 10s Y ears Y ears Contains the lower two BCD digits of the year . Lower nibb le contains the value for years; up per nibble contains the value for 10s of years. Each nibble operates from 0 to 9. The range for the r[...]

  • Page 19

    STK17T A8 Document #: 001-52039 Rev . ** Page 19 of 23 0x1FFF7 Watchdo g Timer D7 D6 D5 D4 D3 D2 D1 D0 WDS WDW WDT WDS W atchdog S trobe. Setting this bit to 1 reloads and restarts the watchdog timer . The bit is cleared automatically once the watchdog timer is reset. The WDS bit is write only . Reading it always will re turn a 0. WDW W a tchdog Wr[...]

  • Page 20

    STK17T A8 Document #: 001-52039 Rev . ** Page 20 of 23 0x1FFF2 Alarm – Seconds D7 D6 D5 D4 D3 D2 D1 D0 M 10s Alarm Seconds Alarm Seconds Contains the alarm value for the seconds and the ma sk bit to select or desel ect the seconds’ value. M Match. Setting this bit to 0 causes the se conds’ value to be used in the alarm match. Setting this bit[...]

  • Page 21

    STK17T A8 Document #: 001-52039 Rev . ** Page 21 of 23 Ordering Information Ordering Codes Packing Option Blank=T ube TR=T ape and Reel T emperatu re Range Blank=Commercial (0 to +70 C) I= Industrial (-45 to +85 C) Access Time 25=25 ns 45=45 ns Lead Finish F=100% Sn (Matte T in) RoHS Compliant Package R=Plastic 48-pin 300 mil SSOP (25 mil pitch) ST[...]

  • Page 22

    STK17T A8 Document #: 001-52039 Rev . ** Page 22 of 23 Package Diagrams Figure 17. 48-Pin SSOP (51-85061) 51-85061 *C [+] Feedback[...]

  • Page 23

    Document #: 001-52039 Rev . ** Revised Ma rch 02, 2009 Page 23 of 23 AutoS tore and Qu antumT rap are re gistered trademarks of C ypress Semiconducto r Corporation. All product s and compa ny names mentio ned in this document are the trad emarks of th eir respect ive holders. STK17T A8 © Cypress Semiconducto r Corporation, 2 009. The information c[...]