Cisco Systems CISCO7206 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Cisco Systems CISCO7206, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Cisco Systems CISCO7206 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Cisco Systems CISCO7206. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Cisco Systems CISCO7206 should contain:
- informations concerning technical data of Cisco Systems CISCO7206
- name of the manufacturer and a year of construction of the Cisco Systems CISCO7206 item
- rules of operation, control and maintenance of the Cisco Systems CISCO7206 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Cisco Systems CISCO7206 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Cisco Systems CISCO7206, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Cisco Systems service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Cisco Systems CISCO7206.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Cisco Systems CISCO7206 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Cisco 7206 Router Quick Start Guide 1 Documentation and R esources 2 Prepare for Installation 3 Rac k-Mount the Router 4 Connect the Rou ter to the Network 5 Star t and Configure the R outer 6 After Installation 7 T ec hnical A ssistance[...]

  • Page 2

    2 1 Documentation and Resources This section contains information to help you prepare for in stalling the Cisco 7206 router . I contains a list of o nline documentation and resources. Document Revision History The Document Revision History below , reco rds technical changes to this document. Documentation Survey Is Cisco documentation helpful? Clic[...]

  • Page 3

    3 Port Adapter Documentation • Cisco 7200 Series Port Adapter Hardware Configuration Guid elines—DOC-783471= (This document provides bandwidth point information for Cisco 7200 series routers and port adapters.) http://www .cisco.com/univercd/cc/td/doc/product/core/7206/port_adp/config/index.htm • Port adapter documentation—See the document [...]

  • Page 4

    4 Ordering Documentation Cisco documentation is available in the follo wing ways: • Registered Cisco.com users (Cisco direct customers) can orde r Cisco product documentation fr om the Networking Products MarketPlace: http://www .cisco.com/cgi-bin/order/order_root.pl • Registered Cisco.com users ca n order the Documentat ion CD-ROM through the [...]

  • Page 5

    5 2 Prepare for Installation War n in g Only trained and qualified personnel should install, repl ace, or service this equipment. War n in g Read the installation instructions before you connect th e system to its power sourc e. War n in g This unit is intended for installati on in restricted access ar eas. A restricted access are a is where access[...]

  • Page 6

    6 • Port adapter documentation fo r configuring the interfaces • T1 channel service unit/data service unit (CSU/DSU) that conv erts the High-Level Data Link Control (HDLC) synchronous serial data stream into a T1 data stream with the correct framing and ones density to connect a serial port to a T1 network. (Some telephone systems require a min[...]

  • Page 7

    7 3 Rack-Mount the Router Brackets Front-Mounted—Chass is Protrudes from the Rack Locate the rack-mount and cable-management brackets and screws (1, 2, 3 in the illustration above) and a Number 2 Phillips screwdriver . 1. Align the rack-mount bracket (1)—as shown above—to the sid e of the router . Insert and tighten the screws (3) if yo u are[...]

  • Page 8

    8 Brackets Front-Mounted—C hassis Recessed in Rack Locate the rack-mount and cable-management brackets and screws (1, 2, 3 in the illustration above) and a Number 2 Phillips screwdriver . 1. Align the cable-management bracket (1) to the side of th e router . Ali gn the rack-mount bracket over it—as shown above—and insert and tighten the screw[...]

  • Page 9

    9 Brackets Rear-Mounted—Front Protrudes from the Rack 1. Locate the threaded screw holes in the rear sides of the chassis. 2. Align a rack-mount bracket (1 ) to the threa ded holes in the right side of the chassis. 3. Using a Number 2 Phillips screwdriver and two M4 x 8-mm Phillip s flathead screw s (2), attach the rack-mount bracket to the route[...]

  • Page 10

    10 Brackets Rear-Mounted—Front Recessed in the Rack 1. Locate the threaded screw holes in the rear sides of the chassis. 2. Align the first rack-mount bracket (1) to the thre aded holes in the right side of the chassis. 3. Using a Number 2 Phillips screwdriver and two M4 x 8-mm Phillip s flathead screw s (2), attach the rack-mount bracket to the [...]

  • Page 11

    11 Chassis Ground Con nection Installation Note The grounding lug and Phillips-head screws are not ava ilable from Cisco Systems. Get the grounding lug from an electrical-connector vendor and th e screws from a hardware vendor . See Page 4 for the parts needed. 1. Locate the chassis ground co nnector (1) on the rea r of your router chassis. 2. Inse[...]

  • Page 12

    12 4 Connect the Router to the Network I/O Controller Console and Au xiliary Port Cable Connections Note Both the console and auxiliary ports are asynchronous serial po rts; any devices connected to these ports must b e capable of asynchronous transmission. 1. Before connecting a terminal to the console port, con figure th e terminal to match the r[...]

  • Page 13

    13 Ethernet Port Connections I/O controllers have the possibility of one or two ty pes of Ethernet connections: MII connections and RJ -45 connection s for 10/100-Mbps operation. For more information about Ethernet ports, see the online Cisco 7206 Installation and Configuration Guide. MII Connections Attach the MII cable to the MII port and tighten[...]

  • Page 14

    14 5 Start and Configure the Router Power Cable Connections War n in g This unit might have more than one power cord. T o reduce the risk of electric shock, disconnect the two power supply cords before servicing t he unit. War n in g The AC power supply has double pole/neutral fusin g. Connecting AC-Input Power 1. At the rear of the router , check [...]

  • Page 15

    15 1. At the rear of the router , check that th e power switch is in the off (O) position. 2. Ensure that the –V and +V lea ds are disconnec ted from the power source. 3. Using a wire stripper , strip approximatel y 0.55 in ch (14 mm) from the –V , +V , and ground leads (2). 4. Insert the stripped end of the ground lead (1) all the way in to th[...]

  • Page 16

    16 Observing System Startup and Pe rforming a Basic Configuration Check conditions prior to system startup: 1. Check that all hardware parts and cables are securely attached to the chassis. 2. Check that a Flash Disk or Flash memo ry card is instal led. 3. Check that the co nsole terminal is turned on. Starting and Conf iguring the Router 1. Place [...]

  • Page 17

    17 Performing a Basic Configurati on Using the Setup Facility If you do not plan to use Auto Install, do not connect the router ’ s serial (W AN) cable to the channel service unit/data service unit (CSU/DSU). If the W AN cable is not connected, the route r boot s from Fl ash memory and goes au tomati cally into the setup facility . Note Y ou can [...]

  • Page 18

    18 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 4096K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x0 Note The first two sections of the configuration script (the ba nner and the installed hardware) appear only at initial system startup. On subsequent uses of the setup command facility , the script [...]

  • Page 19

    19 8. For the following queries, enab le routing on AppleT alk and IPX: Configure AppleTalk? [no]: yes Multizone networks? [no]: yes Configure IPX? [no]: yes 9. For the following queries, do not enable VINES, XNS, DECn et, or bridging: Configure Vines? [no]: Configure XNS? [no]: Configure DECnet? [no]: Configure bridging? [no]: 10. In most cases yo[...]

  • Page 20

    20 Configuring Interfaces Following are the steps for configuring interfaces to allow co mmunication over a LAN or W AN. T o configure the interface parameters, you need your interface networ k addresses and subnet mask information. Consult with your network administrator for this information. Configuring Ethe rnet In terfaces In the following exam[...]

  • Page 21

    21 The following sample display includes a continuous listing of a ll interface configuration parameters selected for Ethernet and synchronous serial interfaces. Thes e para meters are shown in the o rder in which they appear on your console terminal. Only one Ethernet and one synchronous serial in terface are configured for this example. Configuri[...]

  • Page 22

    22 ! end Use this configuration? [yes/no]: yes [OK] Use the enabled mode ‘configure’ command to modify this configuration. Press RETURN to get started! Y our Cisco 7206 router is now minimally conf igured and ready to use. Y ou can use the setup command if you want to modify the parameters after the initial configuration. T o perform more compl[...]

  • Page 23

    23 Performing Complex Configurations After you have installed your Cisco 7206 router hardware and minimal ly configured the system, you might need to perform more complex configurations, which are beyond the scope of this publication. For specif ic information on system and interface configuration, refer to the modular c onfiguration and modular co[...]

  • Page 24

    24 6 After Installation This section contains hardware replacement instructions and information about contacti ng the T echnical Assistance Center . Note The Flash memory card, Flash Di sk, and port ad ap ters support online insertion and removal (OIR). Replace the Network Processing Engine 1. Power down the router . 2. Disconnect the router from t[...]

  • Page 25

    25 Replace the I/O Controller Note Before powering down the router , use the copy running-config tftp command to save the router ’ s runni ng configuration to a TF TP file server . 1. Power down the router . 2. Disconnect the router from the power source. 3. Remove any I/O controller cab les. 4. On the I/O controller (1), unscrew th e captive ins[...]

  • Page 26

    26 Replace the Flash Memory Card or Flash Disk Note Flash memory cards and Flash Di sks are re placeab le while the system is operating. 12. Remove the Flash memory card or Flas h Disk by pushing the ejector button (3). 13. Insert the new Flash memory card or Flash Disk (1 a nd 2). Th e Flash memory card or Flash Disk protrudes from the I/O control[...]

  • Page 27

    27 Replace a Port Adapte r or Service Adapter 1. T o remove a po rt adapter , place the port adapter lever in the un locked position (2). 2. Grasp the handle and pull the port adapter from the router , about halfway out of its slot (3). If you are removing a blank port adapter , pull the blank port adapter completely out of the chassis slot. 3. Wit[...]

  • Page 28

    28 Caution Do not mix power supplies in Cisco 7206 routers. In du al power su pply configurations, both power supplies must be of the same type (two AC-input pow er supplies or two DC-in put power supplies). Caution T o ensure adequate airflow across the router power supplies, a power supply or a power supply filler plate must be installed in each [...]

  • Page 29

    29 7 Technical Assistance Cisco provides Cisco.com as a starting po int for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools by using the C isco T echnical Assistance Center (T AC) W eb Site. Cisco.com registered users have complete acce ss to the t echnical[...]

  • Page 30

    30 If you cannot resolve your technical issues by using the Cisco T AC W eb Site, and you are a Cisco.com registered user , you can open a case online by usi ng the T AC Case Open tool at the following URL: http://www .cisco.com/tac/caseopen If you have Internet access, it is recommend ed that you open P3 and P4 cases through the Cisco T AC W eb Si[...]

  • Page 31

    31[...]

  • Page 32

    Corporate Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.c om T el: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems International BV Haarlerb ergpark Haarlerbergw eg 13-19 1101 CH Amsterdam The Neth e r la nd s www-europe.ci sco.com T el: 31 0 20 357 1000 Fax: 3[...]