Bunn TB6Q manual

1
2
3
4
5
6
7
8
9
10
11

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Bunn TB6Q, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Bunn TB6Q one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Bunn TB6Q. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Bunn TB6Q should contain:
- informations concerning technical data of Bunn TB6Q
- name of the manufacturer and a year of construction of the Bunn TB6Q item
- rules of operation, control and maintenance of the Bunn TB6Q item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Bunn TB6Q alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Bunn TB6Q, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Bunn service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Bunn TB6Q.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Bunn TB6Q item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    TB3/TB6 Series Including: TB3; TB3-LP; TB3Q; TB3Q-LP; TB6; TB6Q ST ARTING WITH SERIAL NUMBER: TU00020000 INST ALLA TION & OPERA TING MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Il[...]

  • Page 2

    Page 2 41465.1 080112 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor . 2) A[...]

  • Page 3

    Page 3 #00831.0000 #00656.0001 #03408.0000 #03409.0000 #37881.0000 • FILL WA TER T ANK BEFORE ENERGIZING • DO NOT OVERLO AD CIRCUIT • KEEP AWA Y FROM COMBUSTIBLES • DO NOT DEFORM PLUG OR CORD • FAILURE TO COMPL Y RISKS EQUIPMENT DAMAGE, FIRE OR SHOCK • BREWER ENERGIZED UNLESS UNPLUGGED SEE INSTRUCTIONS W ARNING #06064.0000 INTRODUCTION [...]

  • Page 4

    Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. 120V model brewers require 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. "A" model brewers require 2-wire, grounded service rated 220-240 volts ac, 10 amp, single phase, 50 Hz. &quo[...]

  • Page 5

    Page 5 120V MODELS These brewers must be connected to a cold water system with a minimum 1.0 gpm flow rate, and operating pressure between 20 and 90 psi (138 and 620 kPa) from a ½˝ or larger supply line. A shut-off valve should be installed in the line before the brewer . Install a regulator in the line when pressure is greater than 90 psi (620 [...]

  • Page 6

    Page 6 INITIAL SET -UP (TB3Q/TB3Q-LP/TB6Q ONL Y) CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions. 1. Remove the top cover from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid. 3.[...]

  • Page 7

    Page 7 INITIAL SET -UP (TB3/TB3-LP/TB6 ONL Y) CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the top lid from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid. 3. Set [...]

  • Page 8

    Page 8 AUTO SWEETENER SET -UP CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions. 1. Remove the top lid and both rear panels. 2. Make sure the brewer water supply is off. 3. Connect sweetener hose from the bag in a box delivery system to the rear fitting marked [...]

  • Page 9

    Page 9 ADJUSTING BREW VOLUMES NOTE: Check that the brewer is connected to water supply , the tank is properly filled, and a funnel and server are in place, prior to setting or modifying batch sizes. 1. T o adjust concentrate volume on TB3/TB6 models, and dilution volume on TB3Q/TB6Q models: Modifying batch sizes. T o modify a batch volume, first [...]

  • Page 10

    Page 10 OPERA TING CONTROLS A. ON/OFF Switch ON - Placing the switch in the left position allows the start switch to activate a timed brew cycle for three gallons of tea. OFF - Placing the switch in the right position stops the brew cycle. Stopping a brew cycle after it has been started will not stop the flow of water into the funnel until the tan[...]

  • Page 11

    Page 11 41465.1 042009 CLEANING CAUTION - CLEAN AND SANITIZE YOUR ICED TEA BREWER DAIL Y DAIL Y : 1. Remove, disassemble and thoroughly clean and sanitize the entire brew funnel. The funnel tip and screen must be free from any tea particles or residue. Reassemble the funnel. 2. Place the ON/OFF switch in the "OFF" position. Remove and tho[...]