English dropdown-ico

Bunn 10420 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Bunn 10420, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Bunn 10420 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Bunn 10420. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Bunn 10420 should contain:
- informations concerning technical data of Bunn 10420
- name of the manufacturer and a year of construction of the Bunn 10420 item
- rules of operation, control and maintenance of the Bunn 10420 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Bunn 10420 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Bunn 10420, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Bunn service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Bunn 10420.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Bunn 10420 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www .bunn.com. This is absolutely FREE, and th[...]

  • Page 2

    2 46819 030912 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor . 2) All othe[...]

  • Page 3

    3 CONTENTS 46819 043012 INTRODUCTION This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel above the faucet that indicates the status of the dispenser . This equipment is for indoor use, either wall-mounted (H5E/X/PC) or on a sturdy counter or shelf. WARRANTY ..........................................[...]

  • Page 4

    4 USER NOTICES The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels. 00656.0001 As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to com[...]

  • Page 5

    5 ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power sour ce until specified in Initial Set-Up. Refer to Data Plate on the Brewer , and local/national electrical codes to determine circuit requirements. 208 & 240 volt ac models Note: This electrical service consists of 2 current carrying conductors (L1 and L2) [...]

  • Page 6

    6 INITIAL SET -UP - H5E, H5X, H5-PC, H10X, Element CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Connect dispenser to the power source and turn on water supply . 2. Place Master ON/OFF switch in the ON position (if equipped). NOTE: (Digital models wit[...]

  • Page 7

    INITIAL SET -UP - H5M CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the upper rear panel and rotate the control thermostat knob fully coun- terclockwise to the “OFF” position and replace the panel. 2. Connect the dispenser to the power sour[...]

  • Page 8

    OPERA TING CONTROLS - PORTION CONTROL ONL Y (a) VOLUME SELECTOR BUTTONS Press and release the button corre- sponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress. ( b) AUTO STOP/MANUAL DISPENSE BUTTON [...]

  • Page 9

    9 PROGRAMMING - H5-E, H5-PC, H5X, H10X When power is applied to the dispenser , the display located on the bottom of the main circuit board will show the software version for 5 seconds, and then it will show the model number (see chart below) it will then go to (-). While the tank is filling, the display will read (FIL). When the tank is full the [...]

  • Page 10

    10 PROGRAMMING - H5-E, H5-PC, H5X, H10X Continued LEVEL 2 PROGRAMMING H1 - DISPENSE TEMPERA TURE LOCKOUT - PORTION CONTROL ONL Y (WILL NOT DISPLA Y ON OTHER MODELS) 1. T o enter Level 2 Programming, press and hold the center button until H1 ap- pears on the display (approximately 6 seconds) then release button. The display will either read noL (LOC[...]

  • Page 11

    Program lockout switch: The switch must be in the “SET” position in order to access the program modes. 1. Disconnect the dispenser from the power source. 2. Remove the 4-40 screws and the top cover . 3. Use a small screwdriver to move switch to set position. 4. Install top cover , connect dispenser to power source. Manual Energy Saver Mode: The[...]

  • Page 12

    12 2. The display will now show the model number . (H5H) 5 Gallon High Voltage Unit (200-240V) (H5L) 5 Gallon Low Voltage Unit (100-120V) Now scroll with the (+/-) buttons through the models listed above until the display matches the model you are working with. 3. Press and release the upper hidden button once more. The display will show P2 . Displ[...]

  • Page 13

    13 LEVEL 2 PROGRAMMING H2 - F° OR C° SELECTION 1. T o enter Level 2 Programming, press and hold the upper hidden button until H2 appears on the display . Release the upper hidden button. The display will show either FA H (Degrees in Fahrenheit) or CEn (Degrees in Centigrade). 2. Press and release the (+) or (-) buttons to alternate between FA H a[...]

  • Page 14

    14 DRAINING THE DISPENSER - OHW CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source and allow dispenser to cool. 2. Tilt dispenser forward over sink. 3. Open faucet. 4. Continue tilting dispenser forward over sink until water stops flowing. NOTE - The dispense[...]