English dropdown-ico

Bostitch GT18B01 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Bostitch GT18B01, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Bostitch GT18B01 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Bostitch GT18B01. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Bostitch GT18B01 should contain:
- informations concerning technical data of Bostitch GT18B01
- name of the manufacturer and a year of construction of the Bostitch GT18B01 item
- rules of operation, control and maintenance of the Bostitch GT18B01 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Bostitch GT18B01 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Bostitch GT18B01, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Bostitch service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Bostitch GT18B01.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Bostitch GT18B01 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    1 GT18B01 HYDRAULIC POWER UNIT S AFETY , O PERA TION AND M AINTENANCE SER VICE MANUAL WARNING Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com Copyright © 2004, The Stanley W orks OPS/MAINT USA 65466 9/2004 V er 1[...]

  • Page 2

    2[...]

  • Page 3

    3 T ABLE OF CONTENTS For the nearest authorized and certifi ed dealer , call Stanley Hydraulic T ools at the number listed on the back of this manual and ask for a Customer Service Representative. SERVICING THE ST ANLEY POWER UNIT : This manual contains safety , operation, and routine mainte- nance instructions. Stanley Hydraulic T ools recommends[...]

  • Page 4

    4 CERTIFICATE OF CONFORMITY Hy draulic Tools ______________________________________________________________________ I, the undersigned: Burrows, James Surname and First names Hereby certify that the c onstruction plant or equipment specif ied hereunder: 1. Manufacturer: Stanley Hydraulic Tools, 3810 Naef Road, Milwauki e, Oregon USA 2. Representati[...]

  • Page 5

    5 Safety symbols and signal words, as shown below , are used to emphasize all operator , maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment. This safety alert and signal word indicate an imminently hazardous situa- tion which, if not avoided, will resu[...]

  • Page 6

    6 T ool operators and maintenance personnel must always comply with the safety precau- tions given in this manual and on the stickers and tags attached to the equipment. These safety precautions are given for your safety . Review them carefully before operat- ing the tool and before performing general maintenance or repairs. Supervising personnel s[...]

  • Page 7

    7 T OOL STICKERS & T AGS 65458 Sound Power Decal 62302 Power Unit Dash Decal 62300 CHOKE D ANGER PULL TO ST ART PUSH TO R UN 62300 Single Circuit 28322 CE Decal AUTO IDLE OFF AUTO IDLE ON R U 62302[...]

  • Page 8

    8 HOSE TYPES Hydraulic hose types authorized for use with Stanley Hydraulic T ools are as follows: ➊ Certifi ed non-conductive ➋ Wire-braided (conductive) ➌ Fabric-braided (not certifi ed or labeled non-conductive) Hose ➊ listed above is the only hose authorized for use near electrical conductors. Hoses ➋ and ➌ listed above are conduc[...]

  • Page 9

    9 HTMA REQUIREMENTS FLOW RA TE TOOL OPERA TING PRESSURE (at the power supply outlet) SYSTEM RELIEF V AL VE SETTING (at the power supply outlet) MAXIMUM BACK PRESSURE (at tool end of the return hose) Measured at a max. fl uid viscosity of: (at min. operating temperature) TEMPERA TURE Suffi cient heat rejection capacity to limit max. fl uid temper[...]

  • Page 10

    10 Chevron A W-MV -32 Exxon "Univis" J-26 Mobil D.T .E. 13 Gulf "Harmony" AW -HVI-150-32 Shell "T ellus" T -32 T exaco "Rando" HD-AZ Union "Unax" AW -WR-32 T erresolve EnviroLogic 132 4. HYDRA ULIC CONNECTIONS The recommended hose length is 25 ft/8 m with a 1/2 inch/12.7 mm inside diameter . The hos[...]

  • Page 11

    11 CONTROL P ANEL RETURN PRESSURE H.T .M.A. 1/2 INCH MALE QUICK DISCONNECT COUPLER H.T .M.A. 1/2 INCH FE- MALE QUICK DISCON- NECT COUPLER 1/2 INCH I.D. HOSE, 25 FT LONG WITH 2500 PSI/ 172 BAR RA TING AND 4 T O 1 SAFETY F ACTOR PRESSURE RETURN 1/2 INCH MALE PIPE HOSE END 1/2 INCH MALE PIPE HOSE END ADAPTER, 3/8 INCH MALE PIPE x -8 SAE O-RING H.T .M.[...]

  • Page 12

    12 CONTROLS This unit is equipped with an advanced proportional engine control system. It provides a means of controlling engine speed by adjusting the fuel control lever with an actuator . The Power Unit provides one circuit, with an oil fl ow of 5 gpm/19 lpm up to 2000 psi/140 bar or 8 gpm/30 lpm up to 2000 psi/140 bar with a factory-programmed [...]

  • Page 13

    13 OPERA TION COLD WEA THER ST ARTUP 1. Use the procedures described under "ST ARTUP" and then follow the procedure below . 2. Hydraulic fl uids are thicker in cold weather . Therefore, it is recommended that the engine be run at low idle long enough to bring the fl uid temperature up to a minimum of 50°F/10°C. 3. If the tools and too[...]

  • Page 14

    14 ST ORAGE • Clean the unit thoroughly before storage. Do not use water pressure. • Always store the unit in a clean and dry facility . • If the unit will be stored for a prolonged period (over 30 days), add a fuel additive to the fuel tank to prevent the fuel from gumming. Run engine for a short period to circulate the additive. • Replace[...]

  • Page 15

    15 CHECKING PERFORMANCE CONTROL™ (ELECTRONIC GOVERNOR-ST A TIC CHECK) T o determine whether a governor problem is being caused by the actuator or the control module, perform the following static check exactly in order shown. A pair of jumper wires and a known good 12-volt battery is required. 1. Disconnect red and green wires from the control mod[...]

  • Page 16

    16 F AUL T CODES 1 APECS unit not calibrated yes Have engine serviced by an Authorized Stanley Dealer . 2 Engine speed excessive yes Have engine serviced by an Authorized Stanley Dealer . 3 Engine speed unusually low yes Have engine serviced by an Authorized Stanley Dealer . 4 Engine shutdown due to engine yes Have engine serviced by an Authorized [...]

  • Page 17

    17 GENERAL T ests and adjustments should be performed periodically to ensure the power unit is operating at maximum effi ciency . Stanley Circuit T ester (part number 04182) is recommend- ed. This tester can be used to isolate problems in both the engine and hydraulic system prior to any power unit disas- sembly . TESTING THE HYDRAULIC CIRCUIT The[...]

  • Page 18

    18 Engine will not start. Flow selector switch not in the Make sure the fl ow selector switch is in OFF position. the OFF position when starting. Battery not connected. Attach battery cables, check wires. Weak battery . T est battery , charge or replace. No fuel. Add Fuel. Fuel fi lter plugged. Replace fuel fi lter . Defective spark plugs. Remov[...]

  • Page 19

    19 Engine: ....................................................................................................................... ........................................ 18 hp Briggs Capacity .......................................................................................... One 5 gpm/19 lpm Circuit or One 8 gpm/30 lpm Circuit Length: ....[...]

  • Page 20

    20 SER VICE GENERAL Service instructions in this section are limited to parts and components other than the engine and hydraulic pump. Other major components should be serviced by representa- tives of the respective manufacturers as follows: ENGINE - Briggs and Stratton V anguard OHV Model-356447-01 15-E1 The Briggs engine should be serviced only b[...]

  • Page 21

    21 Be sure the tapered cone surfaces of the bushing and blower hub are clean and free of anti-seize lubricants. CA UTION 2. Disconnect the wiring harness (See Figure 4, Wiring Diagrams for the correct connections). 3.Follow steps 1 through 4 under "Manifold Assembly Re- moval". 4. Remove the RED wire attached to the starter solenoid and t[...]

  • Page 22

    22 Assemble the bushing and blower hub with the bolts inserted (but not tightened) through the drilled holes in the blower hub and into the tapped holes in the bushing. With the key in the shaft, slide assembly into position on the shaft and tighten the setscrew over the key (if equipped). T ighten the 3 capscrews (14, fi g.1) alternately and even[...]

  • Page 23

    23 SER VICE HYDRAULIC T ANK, COOLER & FIL TER ASSEMBL Y (see fi gure 1, 2 & 3) 1. First remove the hydraulic fl uid from the tank by either pumping it out with a portable drill pump or draining it into a container . 2. Remove the cooler guard (20, fi g. 2) by removing the 2 hex fl ange bolts (9, fi g. 2) and 2 capscrews (21, fi g. 1).[...]

  • Page 24

    24 FIGURE 1. BRIGGS ENGINE ASSEMBL Y 5 6 3 5 3 7 3 4 3 6 5 2 4 4 2 7 5 0 5 1 8 2 6 2 8 4 5 3 0 4 3 3 0 4 7 3 3 3 1 3 0 3 2 2 9 4 9 4 8 1 7 1 6 1 4 1 3 1 2 1 1 9 1 0 4 1 5 2 0 2 1 2 3 1 8 2 5 2 2 1 9 4 1 4 0 3 9 3 8 7 2 1 3 4 6 5 4 5 3 4 4 2 4 5 5 5 7 5 8 5 6 4 2 5 4 4 8 5 9 4 1 1[...]

  • Page 25

    25 ITEM P/N Q T Y DESCRIPTION 1 36150 1 Muffl er 1A 65456 1 Spark Arrester 2 36151 1 Heat Shield 3 36152 2 Screw , Hex W asher 4 59007 1 Briggs Engine 5 56656 1 Coupling 6 07819 1 Square Key 7 07860 2 Capscrew , 3/8-16 x 1-1/4 8 31765 1 Pressure Switch 9 12787 4 Flange Nut 10 24287 1 Clamp 1 1 59076 1 Bushing 12 20990 1 Key 13 59103 1 Blower Hub 1[...]

  • Page 26

    26 FIGURE 2. FRAME P ARTS ITEM P/N Q T Y DESCRIPTION 1 370502 7 Capscrew , 5/16 in. -18 UNC 2 03906 7 Nylock Nut, 5/16 in. -18 UNC 3 62270 1 Handle, Rear Lift 4 58857 1 Coupler , Male 3/8 in., -8 SAE 5 58856 1 Coupler , Female 3/8 in., -8 SAE 6 60962 2 Capscrew , 1/4 in. -20 7 59130 1 Manifold Assy , Single Circuit 8 1 Dash Decal 9 59074 6 Hex Flan[...]

  • Page 27

    27 ITEM P/N QTY DESCRIPTION 1 59130 1 Manifold Assy , Single Circuit 2 59104 1 Hose Barb, 3/4 in. Hose x 3/4 in. Pipe 3 62199 4 Hose Clamp 4 350000 1 Elbow , 45° Straight Thread 5 02773 1 Adapter 6 58569 1 Elbow , 90° 7 58943 1 Hose 8 350104 1 Connector , Straight Thread 9 40364 1 Elbow , 45° 10 59088 1 Hose 1 1 59089 1 Hose 12 59105 1 Hose Barb[...]

  • Page 28

    28 RECTIFIER WIRE WHITE CONTROLLER TO MAGNETO WIRE ON ENGINE GRA Y WIRE OIL PRESSURE SWITCH FUEL SHUTOFF RED WIRE - THROTTLE CONTROL SWITCH (NOTE: PLUG BEHIND SWITCH WITH BLUE & YELLOW WIRES GOES T O SWITCH ON TOP) RELA Y -62301 SUPPLIED W/62293 HARNESS PRESSURE SWITCH TO AC TUATOR RED/GREEN GROUND WIRES MANIFOLD ASSY DIRECTIONAL V AL VE RED TO[...]

  • Page 29

    29 Stanley Hydraulic T ools (hereinafter called “Stanley”), subject to the exceptions contained below , warrants new hydraulic tools for a period of one year from the date of sale to the fi rst retail purchaser , or for a period of 2 years from the shipping date from Stanley , whichever period expires fi rst, to be free of defects in material[...]

  • Page 30

    30 Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com[...]