Black & Decker FS200SD manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Black & Decker FS200SD, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Black & Decker FS200SD one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Black & Decker FS200SD. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Black & Decker FS200SD should contain:
- informations concerning technical data of Black & Decker FS200SD
- name of the manufacturer and a year of construction of the Black & Decker FS200SD item
- rules of operation, control and maintenance of the Black & Decker FS200SD item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Black & Decker FS200SD alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Black & Decker FS200SD, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Black & Decker service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Black & Decker FS200SD.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Black & Decker FS200SD item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    VEA EL ESP AÑOL EN LA CONTRAPORT ADA. POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE. SA VE THIS MANUAL FOR FUTURE REFERENCE. INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTION MANUAL F F F F S S S S 2 2 2 2 0 0 0 0 0 0 0 0 S S S S D D D D 1 1 1 1 0 0 0[...]

  • Page 2

    2 T ABLE OF CONTENTS IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY R[...]

  • Page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury . Used without the safety[...]

  • Page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA [...]

  • Page 5

    5 SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES a[...]

  • Page 6

    6 Fig. A Fig. B GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER 2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts: If the machine is intended for use on a circuit that has an outlet that looks like [...]

  • Page 7

    7 FUNCTIONAL DESCRIPTION NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRA TES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRA TIONS CONT AINED IN THE MANUAL ARE REPRESENT A TIVE ONL Y AND MA Y NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED TO ILLUSTRA TE TECHNIQUE ONL Y . FOREWORD Model FS200SD is a 10" T able Sa w design[...]

  • Page 8

    8 1. Leg (4) (2 with holes at base for attaching wheel bracket and brace) 2. 3/8” Flat Washer for Mounting Saw to Stand & for Assembling Stand (24) 3. Foot (4) 4. M8x1.25 Hex Nut for Mounting Saw to Stand & for Assembling Stand (20) 5. M8x1.25x45mm Hex Screw for Mounting Saw to Stand (4) 6. M8x1.25x20mm Carriage Head Bolts for Assembling [...]

  • Page 9

    UNP ACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective co a ting from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces w[...]

  • Page 10

    10 A TT ACHING MITER GAUGE HOLDER DISCONNECT MACHINE FROM POWER SOURCE. Fig. 5 E A B Fig. 6 G F Fig. 7 Fig. 8 Fig. 9 1. Attach the spring clip (E) Fig. 5 to the miter gauge holder (A) using an M4x.7x10mm pan head screw (F), 3/16" external tooth lockwasher , (B) and M4x.7 hex nut. NOTE: The hex nut (G) Fig. 6 will fit into the recess at the bac[...]

  • Page 11

    11 ASSEMBLING ST AND 1. Attach the rubber feet (H) Fig. 1 1 to the bottom of each leg (F). Locate the two legs (F) which have holes at the bottom for attaching the wheel brackets (G) and brace (E). (Make sure wheels and brackets are properly oriented. See inset Figure 1 1.) T o attach the brackets, remove the nuts from the bolts and insert the bolt[...]

  • Page 12

    12 Fig. 14 Fig. 15 Fig. 16 A TT ACHING BLADE HEIGHT ADJUSTING HANDWHEEL 1. Insert an M6x1x55mm pan head screw (D) Fig. 14 through the handle (E). Attach the handle (E) to the handwheel (A) by threading the screw (D) clockwise into the handwheel. 2. Attach the handwheel (A) Fig. 15 to the shaft (B). Align the flat on the inside of the handwheel to t[...]

  • Page 13

    13 Fig. 22 L B H C Fig. 18 Fig. 21 Fig. 20 Fig. 19 3. Locate the 1/4-20x2" hex head screw (G) Fig. 18. Place the 1/4" internal tooth lockwasher (O) M6.4 flat washer (P) and the 1/4" external tooth lockwasher (R) on the screw (G). 4. Position the recessed end (E) Fig. 19 of the splitter bracket (B) against the end of the pivot rod (F)[...]

  • Page 14

    14 Fig. 26 Fig. 28 Fig. 27 ASSEMBLING RIP FENCE 1. Thread the M8x1.25 hex nut (A) Fig. 26, approximately halfway on the stud of the handle (B). 2. Thread the handle (B) Fig. 26 into the tapped hole (C) in the fence cam (D). T ighten the hex nut (A) Fig. 27 against the cam (D). 3. The rip fence is usually set up on the right hand side of the saw tab[...]

  • Page 15

    MOVING THE SA W T o move the saw , grasp the side of the table opposite of the wheels. Lift the saw so that it is slightly off the floor and pull the table to the desired location as shown. Not all floors are perfectly smooth, check both wheels each time you move the saw to ensure that they are not engaging the floor when the saw is at rest. Make s[...]

  • Page 16

    16 Fig. 32 A B BLADE TIL T ADJUSTMENT T o tilt the saw blade, loosen the lock handle (A) Fig. 32 and move the handwheel (B) until the blade is at the desired angle. T ighten the lock handle (A). NOTE: The lock handle (A) is spring-loaded. Pull out on the handle (A) and reposition it on the serrated stud located underneath the handle. THE BLADE TIL [...]

  • Page 17

    17 RIP FENCE OPERA TION AND ADJUSTMENTS 1. T o move the rip fence (A) Fig. 35 along the table, lift up the fence locking lever (B), slide the fence to the desired location on the table, and push down the fence locking lever (B). 2. The pointer indicates the distance from the fence to the saw blade. If an adjustment is required, loosen the screw (C)[...]

  • Page 18

    18 MITER GAUGE OPERA TION AND ADJUSTMENTS For cross-cutting (blade set 90 degrees to the table), the miter gauge can be used in either table slot. For bevel cross-cutting (with the blade tilted), use the miter gauge in the right table slot only so that the blade will be tilted away from the miter gauge and your hands. T o operate the miter gauge, l[...]

  • Page 19

    19 Fig. 41 1. NOTE: One 7/8" wrench is supplied with the saw for changing the saw blade. 2. Remove table insert (A) Fig. 41, and raise saw blade (F) to its maximum height. 3. T o remove blade, place the wrench (D) on the flats of the arbor nut (C) to keep the arbor from turning. Place a piece of wood (B) flat on the table against the blade so [...]

  • Page 20

    20 Fig. 42A A C B Fig. 42B B (B) can be fastened to the front of the miter gage by using two wood screws (C) through the holes provided in the miter gage body and into the wood-facing. NEVER USE THE FENCE AS A CUT -OFF GAGE WHEN CROSS-CUTTING. When cross-cutting a number of pieces to the same length, a block of wood (B) Fig. 42B can be clamped to t[...]

  • Page 21

    21 Fig. 45 Fig. 46 THE MAXIMUM WIDTH DADO CUT FOR THIS SAW IS 1/2 INCH. THE BLADE GUARD AND SPLITTER ASSEMBL Y CANNOT BE USED WHEN DADOING. IT MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW . Before dadoing, loosen wing nut (A) Fig. 48 and take off the blade guard and splitter assembly (B). Keep assembly handy to replace it after dadoing. AUXILIAR[...]

  • Page 22

    22 Fig. 51 Fig. 52 Fig. 49 Fig. 50 Fig. 48A 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four or five inside cutters, (Fig. 48A). V arious combinations of saws and cutters are used to cut grooves from 1/8” to 13/16” for use in shelving, making joints, tenoning, grooving, et[...]

  • Page 23

    23 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA TERIAL TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the fe[...]

  • Page 24

    24 Fig. 54 Fig. 55 Kerf should be about 1/4" apart. Fig. 54, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructed of, should be a straight piece of wood that is free of knots and cracks. Featherboards are used to keep the work in contact with the fence and table, as shown in Fig. 55, and [...]

  • Page 25

    25 BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS TROUBLE! SA W WILL NOT ST ART WHA T’S WRONG? WHA T TO DO… 1.Saw not plugged in. 1.Plug in saw . 2.Fuse blown or circuit breaker tripped. 2.Replace fuse or reset circuit breaker . 3.Cord damaged. 3. Have cord replaced by authorized service center . 4.Brushes worn out. 4.Have brushes replaced by [...]

  • Page 26

    26 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. W ear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST ART Shoul[...]

  • Page 27

    A V ANT DE RETOURNER CE PRODUIT POUR QUELQUE RAISON QUE CE SOIT , COMPOSER LE NUMÉRO SUIV ANT : 1 800 544-6986 MERCI D’A MERCI D’A VOIR CHOISI FIREST VOIR CHOISI FIREST ORM ! VISITEZ ORM ! VISITEZ WWW WWW .FIREST .FIREST ORMT ORMT OOLS.COM/PRODUCTREGISTRA OOLS.COM/PRODUCTREGISTRA TION TION POUR ENREGISTRER VOTRE NOUVEAU PRODUIT POUR ENREGISTRE[...]

  • Page 28

    28 Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera la mort ou des graves blessures. Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait causer la mort ou de graves blessures. Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait cau[...]

  • Page 29

    29 1. POUR SA PROPRE SÉCURITÉ, LIRE LE MODE D’EMPLOI A V ANT D’UTILISER L ’OUTIL. L ’apprentissage de l’utilisation de cet outil, des restrictions, et des risques qui lui sont propres réduit grandement la possibilité d'accidents et de blessures. 2. PORTER DES PROTECTIONS OCULAIRE ET AUDITIVE. TOUJOURS PORTER DES LUNETTES DE SÉCU[...]

  • Page 30

    30 CONSER VER CES DIRECTIVES. Les consulter souvent et les utiliser pour donner des directives aux autr es. 1. NE P AS UTILISER CET OUTIL A V ANT qu'il ne soit assemblé et installé conformément aux instructions. 2. CONSUL TER LE SUPERVISEUR, instructeur , ou autre personne qualifiée si vous n'êtes pas familiarisé avec le fonctionnem[...]

  • Page 31

    31 Fig. A Fig. B PRISE ÉLECTRIQUE MISE À LA TERRE LAMES CONDUCTRICES LA LAME DE MISE A LA TERRE EST LA PLUS LONGUE DES TROIS LAMES PRISE ÉLECTRIQUE MISE À LA TERRE MOYEN DE MISE À LA TERRE ADAPT A TEUR 2. Pour les machines mises à la terre et branchées à un cordon d’alimentation utilisées sur un circuit d’alimentation de régime nomina[...]

  • Page 32

    32 Figure 3 Quincaillerie 1. (1) Vis à tête cylindrique à dépouille M6x1x55 mm 2. (1) Vis à tête hexagonale de 1/4-20x2 po 3. (1) Vis à tête hexagonale de M6x de 1 x 20 mm 4. (2) Vis à tête hexagonale de 1/4-20 x 1/2 po 5. (1) Vis à tête plate de M6x1x12 mm 6. (1) Vis à tête cylindrique à dépouille de M4x0,7x10 mm 7. (4) Vis à têt[...]

  • Page 33

    33 1. (4) pattes (dont 2 sont perforées à la base pour la fixation du support de roue et de la traverse) 2. (24) Rondelles plates de 3/8 po (4,8 mm) pou fixer la scie à un socle et assembler le socle 3. (4) Pattes 4. (20) Écrous hexagonaux de M8x1,25 pour fixer la scie à un socle et assembler le socle. DÉSEMBALLAGE ET NETTOY AGE Désemballer [...]

  • Page 34

    34 FIXA TION DU POR TE-JAUGE À ONGLET DÉBRANCHER L'APP AREIL DE LA SOURCE D’ALIMENT A TION. 1. Fixer l'attache à ressort (E) fig. 5 du porte-jauge à onglet (A) en utilisant une vis à tête cylindrique de M4x de 0,7 x 10 mm (F), une rondelle à denture extérieure de 3/16 po (4,8 mm), (B) et un écrou hexagonal M4x de 0,7. REMARQUE [...]

  • Page 35

    35 3. Localiser la vis à tête hexagonale 1/4-20x2 po (G, fig. 18. Placer la rondelle à denture intérieure de 1/4 po (6,4 mm) (O), la rondelle plate M6.4 (P) et la rondelle à denture extérieure de 1/4 po (6,4 mm) (R) sur la vis (G). 4. Positionner l’extrémité en retrait (E), fig. 19, du support du couteau séparateur (B) contre l’extrém[...]

  • Page 36

    36 A VERTISSEMENT A VERTISSEMENT A VERTISSEMENT surcharge (coupe trop rapide, utilisation d'une lame émoussée, utilisation de la scie au-delà de ses capacités, etc.) ou d'une basse tension, mettre l'interrupteur à la position d'arrêt. Laisser refroidir le moteur pendant trois à cinq minutes. Enfoncer la touche de réiniti[...]

  • Page 37

    37 UTILISA TION ET RÉGLAGES DE LA JAUGE À ONGLET Pour le tronçonnage (lame à 90 degrés de la table la jauge à onglet peut être utilisée dans l'une ou l'autre fente sur la table. Pour un tronçonnage en biseau (avec la lame inclinée) utiliser la jauge à onglet dans la fente droite de la table uniquement pour que la lame soit incl[...]

  • Page 38

    38 UNE DES RÈGLES D'UTILISA TION D'UNE SCIE : NE JAMAIS SE SUSPENDRE SUR, NI TOUCHER LA P ARTIE DE LA PIÈCE À DÉCOUPER. T enir la pièce supportée, et non la pièce coupée. Le tronçonnage se poursuit jusqu’à ce que la pièce soit coupée en deux, et que la jauge à onglet et la pièce reviennent au point de départ. A vant de re[...]

  • Page 39

    39 UTILISA TION DU P AREMENT EN BOIS AUXILIAIRE F ACE AU GUIDE LONGITUDINAL En exécutant certaines coupes spéciales – et si cette opération peut mettre l'accessoire de coupe en contact avec le guide – il faut ajouter un parement en bois (A) fig. 47A, d'un côté du guide longitudinal tel qu'illustré. Le parement en bois se fi[...]

  • Page 40

    40 ENTRETIEN GARDER LA MACHINE PROPRE Dégager régulièrement toutes les conduites d’air avec de l’air comprimé sec. T outes les pièces en plastique doivent être nettoyées à l'aide d'un chiffon doux humide. NE JAMAIS utiliser de solvants pour nettoyer les pièces en plastique. Les solvants peuvent dissoudre ou endommager le mat?[...]

  • Page 41

    41 Les accessoires recommandés pouvant être utilisés avec l’outil sont disponibles auprès de votre distributeur local ou centre de réparation autorisé. Pour tout renseignement concernant les accessoires, composer le : 1-800-544-6986 l’utilisation de tout accessoire non recommandé avec l’outil pourrait s’avérer dangereuse. T ous les [...]

  • Page 42

    42 S S S S I I I I E E E E R R R R R R R R A A A A D D D D E E E E B B B B A A A A N N N N C C C C O O O O F F F F S S S S 2 2 2 2 0 0 0 0 0 0 0 0 S S S S D D D D 2 2 2 2 5 5 5 5 4 4 4 4 M M M M M M M M ( ( ( ( 1 1 1 1 0 0 0 0 ” ” ” ” ) ) ) ) MANUAL DE INSTRUCCIONES ANTES DE DEVOL ANTES DE DEVOL VER ESTE PRODUCTO POR CUALQUIER MOTIVO, LLAME[...]

  • Page 43

    43 Indica una situación de inminente riesgo, la cual, si no es evitada, causará la muerte o lesiones serias. Indica una situación potencialmente riesgosa, que si no es evitada, podría resultar en la muerte o lesiones serias. Indica una situación potencialmente peligrosa, la cual, si no es evitada, podría r esultar en lesiones menores o mode-r[...]

  • Page 44

    44 1. P ARA SU PROPIA SEGURIDAD, LEA EL MANUAL DE INSTRUCCIONES ANTES DE UTILIZAR LA MÁQUINA. Al aprender la aplicación, las limitaciones y los peligr os específicos de la máquina, se minimizará enormemente la posibilidad de accidentes y lesiones. 2. USE PROTECCIÓN DE LOS OJOS. USE SIEMPRE ANTEOJOS DE SEGURIDAD. Use también una careta o una [...]

  • Page 45

    45 REGLAS DE SEGURIDAD ADICIONALES P ARA SIERRA DE MESA 1. NO UTILICE EST A MÁQUINA hasta que esté completamente montada e instalada de acuerdo con las instrucciones. 2. OBTENGA ASESORAMIENTO de su supervisor , instructor u otra persona calificada si no está completamente familiarizado con la utilización de esta máquina. 3. SIGA TODOS LOS CÓD[...]

  • Page 46

    46 CAJA TOMACORRIENTE CONECT ADA A TIERRA TERMINALES QUE LLEV AN CORRIENTE EL TERMINAL DE CONEXIÓN A TIERRA ES EL MÁS LARGO DE LOS 3 TERMINALES MEDIO DE CONEXIÓN TIERRA ADAPT ADOR CAJA TOMACORRIENTE CONECT ADA A TIERRA 1. T odas las máquinas conectadas con cordón conectadas a tierra: En caso de mal funcionamiento o avería, la conexión a tier[...]

  • Page 47

    47 1. Pies (4) (2 con orificios en la base para montar el soporte de la rueda y la abrazadera) 2. Arandela plana de 3/8" para montar la sierra en la base de soporte & para montar la base de soporte (24) 3. Pie (4) 4. T uerca hexagonal M8 para montar la sierra en la base de soporte & para montar la base de soporte (20) 5. T ornillo hexa[...]

  • Page 48

    48 ENSAMBLAJE DESEMP AQUET ADO Y LIMPIEZA Desempaque cuidadosamente la máquina y todas las piezas sueltas que están en el contenedor o contenedores de transporte. Quite el revestimiento pr otector de todas las superficies no pintadas. Este revestimiento puede quitarse con un paño suave humedecido con queroseno (no utilice acetona, gasolina ni di[...]

  • Page 49

    49 1. Fije las patas de goma (H) Fig. 11 a la parte inferior de cada pie (F). Ubique los dos pies (F) que tienen orificios en la parte inferior para fijar los soportes de la rueda (G) y la abrazadera (E). (Asegúrese de que las ruedas y los soportes estén bien orientados. Consulte el r ecuadro de la Figura 11). Para fijar los soportes, retir e las[...]

  • Page 50

    50 ENSAMBLADO DEL VOLANTE DE INCLINACION Y ELEV ADO DE HOJA 1. Inserte el tornillo de M6x1x55 screw (D) Fig. 14, a través de la agarradera (E) y ensamble la agarradera (E) al volante de mano (A) mediante el roscado del tornillo (D) en el sentido de las manecillas del reloj hacia dentr o del volante de mano. 2. Ensamble el volante de mano (A) Fig. [...]

  • Page 51

    51 ARRANCANDO Y DETENIENDO LA SIERRA El interruptor (A) Fig. 29 está localizado en el tablero delanter o del gabinete de la sierra. Para encender la sierra, mueva el interruptor (A) a la posición superior . Para apagar la sierra, mueva el interruptor (A) a la posición inferior . ASEGÚRESE DE QUE EL INTERRUPTOR ESTÉ EN LA POSICIÓN "OFF&qu[...]

  • Page 52

    52 FUNCIONAMIENTO Y AJUSTES DE LA GUIA DE CORTE A LO LARGO 1. Para mover la guía de corte a lo lar go (A) Fig. 35, a lo lar go de la mesa, levante la palanca de cierre (B), deslice la guía a la posición deseada en la mesa y empuje la palanca de cierre de la guía (B) hacia abajo para fijar la guía a dicha posición. 2. Se suministra un indicado[...]

  • Page 53

    53 CAMBIO DE LA HOJA DESCONECTE LA MÁQUINA DE LA FUENTE DE ALIMENT ACIÓN. UTILICE HOJAS DE SIERRA CON UN DIÁMETRO DE 254 MM (10”) CALIFICADAS P ARA 4700 RPM O MA YOR. UTILICE ÚNICAMENTE HOJAS DE SIERRA CON ORIFICIOS P ARA MANDRIL DE 16 MM (5/8”). 1 . NOT A: Junto con la sierra se suministra una llave de 22,2 mm (7/8") para cambiar la h[...]

  • Page 54

    54 UNA TOPE-GUIA SIEMPRE SE DEBE UTILIZAR P ARA LAS OPERACIONES LA REALIZACIÓN DE CORTES AL HILO. NUNCA REALICE UNA OPERACIÓN QUE LA REALIZACIÓN DE CORTES AL HILO HECHO A PULSO. 1. Arranque el motor y haga avanzar la pieza de trabajo sujetándola hacia abajo y contra el tope-guía. No se sitúe nunca en la línea del corte de la sierra cuando re[...]

  • Page 55

    55 EL CONJUNTO DE PROTECTOR DE LA HOJA Y SEP ARADOR NO SE PUEDE UTILIZAR CUANDO SE REALICEN OPERACIONES DE RANURADO Y SE DEBE QUIT AR O GIRAR HAST A LA P ARTE TRASERA DE LA SIERRA. T AMBIÉN SE DEBEN USAR POSICIONADORES AUXILIARES, DISPOSITIVOS DE FIJACIÓN, P ALOS DE EMPUJAR Y T ABLAS DE CANTO BISELADO. 3. En la Fig. 52 se muestra una operación d[...]

  • Page 56

    56 ASEGÚRESE DE SEGUIR LAS REGLAS E INSTRUCCIONES DE SEGURIDAD PROBLEMA: LA SIERRA NO ENCIENDE ¿QUÉ SUCEDE? QUÉ HACER… 1.La sierra no está enchufada. 1.Enchufe la sierra. 2.Fusible quemado o interruptor 2.Reemplace el fusible o reinicie el automático activado. interruptor automático. 3.Cable dañado. 3.Llevela al centro de mantenimiento au[...]

  • Page 57

    57 RÉP ARA TION GARANTIE Cat.No. FS200SD Form No. 90514421 MAR. ‘07 Copyright © 2007 Black & Decker Printed in China T odos los Centros de Servicio Black & Decker están dotados de personal capacitado para proporcionar un servicio técnico eficiente y fiable a las máquinas herramientas de nuestros clientes. Contacte al local Black &[...]

  • Page 58

    58 NOTES / NOT AS[...]

  • Page 59

    59 NOTES / NOT AS[...]

  • Page 60

    60 NOTES / NOT AS[...]