Zenoah BK2651DL manuale d’uso

GB-1 G B BK2651DL BK2651DL G B OWNER’S MANUAL BRUSHCUTTER 848EFT93A1 (704)[...]

GB-2 BK2651DL EC DECLARA TION OF COMFORMITY We, ZENO AH CO ., L TD. 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following pr oducts referr ed to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC EN ISO 11806, ISO 14865 : 1997 2000/14/EC Internal contr ol production. The products referr ed to are: DE[...]

GB-3 G B BK2651DL 1. Par ts location SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to pre vent possib le ser ious bodily injury , and for this reason you are requested to read all such instructions carefully and follow them without fail. W ARNIN[...]

GB-4 BK2651DL Model BK2651DL Overall size (LxWxH) mm 2621 x 414 x 330 Dry weight kg 8.3 Engine Model Zenoah G26LS Displacement cm 3 25.4 Fuel Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Carburetor Diaphragm type Ignition system Flywheel magneto (C.D.I.) Spark plug NGK BPMR 7A Fuel tank capacity L 1.1 Starter Recoil starter Clutch [...]

GB-5 G B BK2651DL 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer fr om whom you purchased the pr od- uct[...]

GB-6 BK2651DL ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts. W ARNING Never place the throttle into the high-speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting at- tachment stops rotating when the throttle is moved fully back t[...]

GB-7 G B BK2651DL • IF SOMEONE COMES 1. Guard against hazar dous situa- tions at all times. W arn adults to keep pets and children away fr om the area. Be careful if you ar e ap- proached. Injury may result fr om flying debris. 2. If someone calls out or otherwise interrupts you while working, al- ways be sure to turn off the en- gine before turn[...]

GB-8 BK2651DL 6. Set up INST ALLING THE SHOULDER STRAP 1. Hook the upper part of the shoulder strap at the notch on the top of the frame and pass it through the buckle as shown in the Figure, then secur e it firmly . 2. Put the hook at the lower part of the shoulder strap in the strap installing location at the bottom of the frame. Buckle Fr ame Ho[...]

GB-9 G B BK2651DL ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 (when using ZENO AH genuine oil) • Exhaust emission are contr olled by the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the intro- duction of an inert material during combustion. •[...]

GB-10 BK2651DL IMPORT ANT • Overchoking may make the engine har d to start due to excess fuel. If the engine fails to start after several attempts, open the choke and repeatedly pull the r ope, or remove the spark plug and dry it befor e tr ying again. ST ARTING A W ARMED ENGINE Y ou can start a war med engine while carrying the unit on the back.[...]

GB-11 G B BK2651DL NOTE • This brush cutter can be operated in either the right side or left side position. The rope guide position is fixed for right side position operation when shipped from the factory . • Adjust the rope guide position as shown in the figur e to allow the operator in the left-hand position to pull the recoil starter with th[...]

GB-12 BK2651DL 8. Operation PUTTING ON THE UNIT NOTE • When carrying the unit on the back, make sure that the throttle lever is set to the idling position and that the throttle wir e will not become twisted and tensioned. 1. After confirming that there is no person or obstacle nearby , grasp the end of the main pipe handle (cutter head side) with[...]

GB-13 G B BK2651DL 9. Maintenance Every Every Ever y 25 50 100 System/components Procedure Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter , fuel filter inspect/clean ✔✔ r eplace, if necessary see adjusting replace carbur etor idle adjusting screw ✔ idling speed if necessary cle[...]

GB-14 BK2651DL 9. Maintenance 9. Maintenance (1) Fuel filter (1) Stopper (2) Flexible liner (3) Gear case (4) Inner shaft (1) Air filter W ARNING • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a per sonal injury . AIR FIL TER • The a[...]

GB-15 G B BK2651DL INT AKE AIR COOLING VENT W ARNING • Never touch the c ylinder , muffler , or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns. • When checking the machine to make sure that it is okay before using it, check the a[...]

GB-16 BK2651DL Limited warranty Should any failure occur on the pr oduct under normal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profession- ally , and 30 days if used for rental purpose) fr om [...]