Water Heater Innovations 196284-001 manuale d’uso

1 PRINTED IN U.S.A. 1004 PLACE THESE INSTRUCTIONS ADJACENT T O HEA TER AND NOTIFY OWNER TO KEEP FOR FUTURE REFERENCE. COMMERCIAL GAS W A TER HEA TER Glass-Lined T ank-T ype W ater Heater P ART NO. 196284-001 • INST ALLA TION • OPERA TION • SERVICE • MAINTENANCE Thank you for buying this energy efficient water heater . We appreciate your con[...]

2 FOREWORD The design of models ***-75 and 100 comply with the latest version of ANSI Z21.10.3-CSA 4.3 as automatic storage or automatic circulating tank type water heaters. Installation diagrams are found in this manual. These diagrams will serve to provide the installer with a reference for the materials and method of piping necessary . It is hig[...]

3 GENERAL SAFETY INFORMA TION PRECAUTIONS DO NOT USE THIS APPLIANCE IF ANY P ART HAS BEEN UNDER W A TER. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water . IF THE UNIT IS EXPOSED TO THE FOLLOWING, DO NOT OPERA TE HEA TER UNTIL ALL CO[...]

4 IF YOU EXPERIENCE AN OUT -OF-GAS SITUA TION, DO NOT TR Y T O RELIGHT APPLIANCES YOURSELF , ask your LP delivery person to relight pilots for you. Only trained LP professionals should conduct the required safety checks in accordance with industry standards. EXTENDED NON-USE PERIODS W ARNING HYDROGEN GAS CAN BE PRODUCED IN A HOT W A TER SYSTEM SERV[...]

5 Drain pans suitable for these heaters are available from your distributor or Apcom Inc., 125 Southwest Parkway , Franklin, TN 37065 or contact them by phone, 615-794-5574 or fax 615-791-0660. W ater heater life depends upon water quality , water pressure and the environment in which the water heater is installed. Water heat- ers are sometimes ins[...]

6 If the unconfined space is within a building of tight construction (buildings using the following construction: weather stripping, heavy insulation, caulking, vapor barrier , etc.), air for combustion, ventilation and draft hood dilution must be obtained from outdoors. The installation instructions for confined spaces in tightly constructed build[...]

7 VENT CONNECTION V ent connections must be made to an adequate stack or chimney . Size and install proper size vent pipe. Do not reduce pipe size to less than that of the draft hood outlet. Horizontal runs of vent pipe must have a minimum upward slope toward the chimney of 1/4 inch per foot. Dampers or other obstructions must not be installed in b[...]

8 Size the main gas line in accordance with T able 1. The figures shown are for straight lengths of pipe at 0.5 in. W .C. pressure drop, which is considered normal for low pressure systems. Note: Fittings such as elbows, tees and line regulators will add to the pipe pressure drop. Also refer to the latest version of the National Fuel Gas Code. TABL[...]

9 THERMOSTAT FOR NATURAL AND PROPANE GASES FIGURE 6. GAS PRESSURE REGULA TOR The gas pressure regulator is built into the gas valve and is equipped to operate on the gas specified on model and rating plate. The regulator is factory adjusted to deliver gas to burner at correct water column pressure allowing for a nominal pressure drop through the co[...]

10 FOR YOUR SAFETY READ BEFORE LIGHTING BEFORE LIGHTING: ENTIRE SYSTEM MUST BE FILLED WITH W A TER AND AIR PURGED A T F AUCETS . W ARNING: If you do not follow these instructions exactly , a fire or explosion may result causing property damage, personal injury or loss of life. 1. STOP! Read the safety information above on this label. 2. Set the the[...]

11 FOR YOUR SAFETY READ BEFORE LIGHTING BEFORE LIGHTING: ENTIRE SYSTEM MUST BE FILLED WITH W A TER AND AIR PURGED A T F AUCETS . W ARNING: If you do not follow these instructions exactly , a fire or explosion may result causing property damage, personal injury or loss of life. 1. STOP! Read the safety information above on this label. 2. Set the the[...]

12 TEMPERA TURE REGULA TION DANGER THIS W A TER HEA TER IS EQUIPPED WITH AN ADJUST ABLE THERMOST A T TO CONTROL W A TER TEMPERA TURE. HOT W A TER TEMPERA TURES REQUIRED FOR AUTOMA TIC DISHWASHER AND LAUNDRY USE CAN CAUSE P AINFUL SCALDING WITH POSSIBLE SERIOUS AND PERMANENT INJURY . THE TEMPERA TURE A T WHICH INJUR Y OCCURS V ARIES WITH THE PERSON?[...]

13 • If the back draft cannot be corrected by the normal method or if a suitable draft cannot be obtained, a blower type flue gas exhauster must be employed to assure proper venting and correct combustion. HIGH TEMPERA TURE LIMIT SWITCH (Auto Reset T ype Energy Cut Off) TO RESET AUT OMA TIC GAS SHUTO FF This water heater is equipped with a automa[...]

14 T ABLE 3. INPUT CHECK TIME REQUIRED TO CONSUME 1 CU. FT . OF GAS Approx. Time Required T ype of BTU Per T o Consume 1 Cu. Ft. Model Gas Cu. Ft. of G as ***-75 Natural 1050 50.3 sec. Propane 2500 1 19.8 sec. ***-100 Natural 1050 50.3 sec. Propane 2500 1 19.8 sec. Use this formula to “clock” the meter . Be sure that other gas consuming applian[...]

15 PREVENTIVE MAINTENANCE RECOMMENDED PROCEDURE FOR PERIODIC REMOV AL OF LIME DEPOSITS FROM T ANK TYPE COMMERCIAL W A TER HEA TERS The amount of calcium carbonate (lime) released from water is in direct proportion to water temperature and usage, see chart. The higher the water temperature or water usage, the more lime deposits are dropped out of th[...]

16 Prepare the Water Heater T o delime the water heater using the Flo-Jug method, first prepare the heater for deliming. Then install the long plastic male adapter fitting into the drain valve opening of the water heater . Use teflon tape and hand tighten only . Do not overtighten. Prepare the Up-N-Down Transfer Kit The next step is the preparation[...]

17 PLUG THE TEMPERA TURE AND PRESSURE RELIEF V A L VE. Also, the leakage could be due to unusually high water pressures or temperatures in the system, or to a faulty relief valve. Y our dealer or a qualified service technician should be called to determine the cause of the problem and to correct it. 4. If you cannot identify or correct the source o[...]

18 NOTES[...]

19 NOTES[...]

20[...]