Smeg ALFA201XE manuale d’uso

Index 1. PRECAUTIONS FOR SAFETY AND USE _____________________ 21 2. INSTALLING THE OVEN __________________________________ 23 3. DESCRIPTION OF C ONTROLS ____________________________ 25 4. USING THE OVEN _______________________________________ 26 5. CLEANING AND MAIN TENANCE ___________________________ 33 6. EXTRAORDINARY MAINTENAN CE _____________[...]

Presentation 1. PRECA UTIONS FOR SAFETY A ND USE THIS MANUAL IS AN I NTEGRAL PART OF T HE APPLIANCE. TAKE GOOD CARE OF IT A ND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE. WE URG E YOU TO READ THI S MANUAL AND ALL THE INFORMATIO N IT CONTAINS CAREFULLY BEFO RE USING THE OVEN. INSTALLATIO N MUST BE CARRIED O UT BY QUALIFIED STAFF IN COMPLI[...]

Presentation NEVER PLAC E INFLAMMABLE OBJECTS I N THE OVEN: IF IT SHOU LD ACCIDENTALLY BE SWITCHED ON, T HIS MIGHT CAUSE A FIRE. THE APPLIAN CE BECOMES VERY HOT DURI NG USE. OVEN GLOVES SHOULD ALWAY S BE WORN. THE NAMEPLA TE WITH THE TECHNICAL DATA, SERIAL NUM BER AND MARK IS IN A VISIBL E POSITION ON THE BACK OF TH E OVEN. THIS NAMEP LATE MUST NEV[...]

Instructions for the Installer 2. INST ALLING THE O VEN The oven is designed for free-standi ng installation on a horizontal work- top. It must be far enough from the wa ll behind it to allow easy access to the terminal board for conne ction of the power supply lead. Installatio n must be carried out by a qualified engineer in compliance with th e [...]

Instructions for the Installer 24 2.2 Safety thermosta t The oven is fitted with a safety devic e tripped in case of a serious malfunction. To reset the safety dev ice, call the after-sales service. The manufacturer declin es all responsibility for injury or damage caused by failure to comply with t he above regulations or deriving from tampering w[...]

Instructions for the User 3. DESCRIPTION OF CONTROLS STOP BUTTON Use this button to set th e time when tu rning on the appliance for the first time or after a power failure, scroll through preset programs and t erminate cooking cycles. START BUTTON Use this button to set th e time when tu rning on the appliance for the first time or after a power f[...]

Instructions for the User 26 4. USING THE O VEN 4.1 Precautions and General Advice When the oven is used for the first time, it should be heated to 200°C for long eno ugh to burn off any oily residues left by the manufacturing process. If you have to carry out any procedures on foods, leave the door open for as short a time as possible to ensure t[...]

Instructions for the User P5.5 or P3.0 for single-phase power connection. After selecting the appropriate power, press STOP to confirm the setting. N.B. This power setting operation only has to be carried out the first time the oven is connected. The value set is saved and automatically us ed whenever the oven is switched on after this. To modify t[...]

Instructions for the User 28 To edit a humidified fan-mod e program by entering the parameters ex actly as required, turn the knob to one of the programs from P1 to P14. The display shows the parameters c ontained in the selected program. Hold down STOP for 2 seconds. A beeper sounds to indicate that the editing mode has been accessed , and the mes[...]

Instructions for the User The display shows UEnd . The parameters set are now saved i n the chosen program. Press START to display the pa rameters just set. Press START again to run the program just edite d. 4.8 Humidified fan-mode cooking Use the knob to select one of the preset programs (P1 – P14). The display shows the parameter s of the selec[...]

Instructions for the User 30 N.B. - during preheating and cooking, whenever the door is opene d the message "door" will appear on the display a nd a beep will sound to warn the user that the door must be clos ed while t hese operations are in progress. 4.9 Modifying a previously edited program To modify one of the programs, turn the knob [...]

Instructions for the User 4.10 Manual cooking Use the knob to select the manual program. The special feature of this user-edi table program is that the co oking parameters set are not retained in the memory when the k nob is turned to any other position. This means that an "empty" program is always immediately available for quick, easy ed[...]

Instructions for the User 32 4.13 Possible error messages on the display 4.13.1 Err1 This message appears whenever the so ft ware detects that the sensor connector is not properly connected to the electro nic circuit board or has short-circuited. This error resets automatically when the oven’s power su pply is switched off. If the error persists,[...]

Instructions for the User 5. CLEANING AND MAINTENANCE Important: never point jets of water str aight at the oven and do not use h igh- pressure water cleaners. Before carrying out any operation, disconnect the oven from the electricity supply. 5.1 Cleaning stainless steel To keep stainless steel in good condit ion, it must be cleaned regularly a t [...]

Instructions for the User 34 5.2 Cleaning the inside of the oven To keep the oven in g ood condition, it must be clea ned regularly at the end of each day, after allowing it to cool. Remove all rem ovable parts. Remove the side runners by lifting them and sliding them off the supporting pins. (as shown here). • Clean the oven shelves and side run[...]

Instructions for the User 5.3 Door glazing The pane of glass in the oven door is very easy to clean since the inside window can be opened. This means that each pane of glass ca n be cleaned on both the inside and the outside. To open the inside pane, simply gently pull out the two points shown in figure 1. After cleaning, to close the inside window[...]

Instructions for the User 36 6. EXTRA ORDINAR Y MAINTENANCE Occasionally, the oven will require minor servicing procedur es or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific operations for each procedure of this kind are provided below. Before carrying out any operation, disconnect the oven from t[...]