Sharp HTSB250 manuale d’uso

ENGLISH MODEL HT -SB250(BK) SOUND BAR SYSTEM OPERA TION MANUAL B arcodesof t http://www.barcodesoft.com Barcode Symbology: Code 93 ; Font Facenam e: Code93 M H r Data To Encode: TINSZA877AWZZ Point Size 8 : *TINSZA877AWZZFP*| Point Size 10 : *TINSZA877AWZZFP*| Point Size 12 : *TINSZA877AWZZFP*| Point Size 14 : *TINSZA877AWZZFP*| Printed in Malaysia[...]

E-1 Special notes W ARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CO VER (OR B ACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QU ALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols: The lightning flash with [...]

E-2 IMPORT ANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety . However , improper use can result in electric shock and/or re. In order to prevent pote[...]

E-3 IMPORT ANT SAFETY INSTRUCTIONS (continued) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualied technician to restore the pr[...]

E-4 For U.S. customer only CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace t[...]

E-5 V olume control ■ The soun d level at a given volum e settin g depend s on unit efficiency , location, and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on with the vol ume control setting up high, or while continually listening at high volumes. Precautions (continued) for [...]

E-6 1 10 9 1 1 14 15 12 1 3 3 2 4 5 7 6 8 Audio Line In 2 Jack ................................. 9 Line In 1 Jacks ......................................... 9 DC Input Jack ........................................ 10 1. 2. 3. Reference page Rear Panel ■ Controls and indicators (continued) Remote Control ■ Remote Control T ransmitter Cinema/Game[...]

E-7 System preparation Make sure to unplug the AC power cord before installing the unit or changing the position. Select from three installation methods according to the preferred position. Using spikes Nuts (secured on spikes) must be used when installing spikes. The unit can be levelled by adjusting the spikes and nuts. Option 2 Option 1 Tighten [...]

E-8 Fix a wall mount plug into the hole using a hammer, until it is ush with the wall surface. 3 1-1/4” (32 mm) 3/8” (8-9 mm) W all surface S y s t e m p r ep a r a t io n ( c o n t i n u e d ) W all surface Screw the wall mount angle to the wall as shown in the illustration. (T otal screw is 8 pieces) 4 W all mount angle W all mount angle W[...]

E-9 Falling prevention Safety wires (not suppl ied) are usef ul to prevent the unit from falling off the table. Loop the safety wires (not supplied) into each hole as shown and tie the safety wires to the LCD TV stand. Sound bar connections to TVs Caution: Turn off all other equipment before making any connections. T uner receiving for other audio [...]

E-10 AC power connection Aft er che cki ng al l the con ne cti ons have bee n mad e correctly , connect the AC power cord to the AC power input jack, then to the AC outlet. Using with the AC/DC adaptor ■ 1 Plug the AC power cord into the AC/DC adaptor . 2 Plug the AC/DC adaptor cable into the DC INPUT jack on the unit. 3 Plug the AC power cord in[...]

E-1 1 shall not be exposed to excessive heat such as sunshine, re or the like. Installing the battery incorrectly may cause the unit to malfunction. Notes concerning use: Replace the battery if the operating distance is reduced or if the operation becomes erratic. Purchase “CR 2025”, coin lithium battery . Periodically clean the transmitter [...]

E-12 General control (continued) Muting ■ The volume is muted temporarily when pressing the MUTE button on the remote cont rol. Pres s again to restore the volume. Preset sound mode ■ Main unit operation: T o change to a different mode, press the SURROUND button repeatedly until the desired sound mode lights up. Remote control operation: Press [...]

E-13 Symptom Possible cause No sound is heard. Is the input signal (selection) set properly? Is the volume level set to “0”? Is muting activated? ● ● ● Noise is heard during playback. Move the unit away from any computers or mobile phones. ● When a button is pressed, the unit does not respond. Set this unit to the stand-by mode and then[...]

E-14 T roubleshooting chart (continued) Condensation ■ Sudden temperature changes, storage or ope rat ion in an extr eme ly hu mid envir onm ent may cause condensation inside the cabinet or on the transmitter on the remote control. Conden sation can cause the unit to ma lfunc- tion. If this happens, leave the power on until normal playback is pos[...]

E-15 Specications As part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement without prior notice. The performance specica- tion gures indicated are nominal values of production unit. There may be some deviations from these values in individual unit. Power sou[...]