Sears 149.213340 manuale d’uso

SERIAL OR CODE NUMBER: Model and code number may be found on1he right side of Spindie Housing You should record both model and serial number and retain in a satepiace for future use CALIFORNIA OWNERS: a unique serial code number is stamped inside the Pulley Cover CAUTION: Read All Instructions Carefully Before Start- ing Assembly and Use. Save This[...]

FULL ONE-YEAR WARRANTY ON CRAFTSMAN RADIAL DRILL PRESS If within one year from date of purchase, this Craftsman RADIAL DRILL PRESS fails due to a defect in materi- al or workmanship, Sears will repair it, free of charge WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER IN THE UNITED STATES, . This warranty gives [...]

4 REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see thatkeys and adjusting wrenches are removed from tool before turning on 5 KEEP WORK AREA CLEAN Cluttered areas and beeches invite accidents 6 DON'T USE IN DANGEROUS ENVIRONMENT Don't use power tools in damp or wet locations, or expose them to rain Keep work area well illum[...]

SAFETY RULES FOR DRILL PRESSES 1 DO NOT USE until unit is completely assembled and installed according to instructions 2 USE ONLY CHUCK KEY PROVIDED WiTH YOUR RADIAL DRILL PRESS It is equipped with a self-ejecting pin that elimi- nates hazard of leaving key in chuck 3 ALWAYS WEAR EYE PROTECTION 4 DO NOT WEAR Gloves, necktie or loose fitting ciothin[...]

TOOLS REQUmRED 8-inch Adjustable Mallet Wrench UNPACKRNG AND CHECKUNG CONTENTS Model 149213340 Radial Drill Press is shipped complete in one carton Carefully unpack and separate parts from packing material Check loose parts against Table of Loose Parts on page 5 and parts list on page 15 If any parts are missing or damaged, do not attempt to assemb[...]

ASSEMBLY WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT THE RADIAL DRILL PRESS TO A POWER SOURCE UNTIL ALL ASSEMBLY STEPS ARE COMPLETE_ AND YOU HAVE READ AND UNDERSTOOD SAFETY AND OPERATIONAL INSTRUCTIONS= CAUTION: Do NOT ALLOW BRAKE FLUIDS_ GASOLINE, PENETRATING OILS 1 ETC,_ TO COME IN CONTACT WITH PLASTIC PARTS, THESE SOLUTIONS CONTAIN CHEMICALS THA[...]

I 7 Make sure bottom of Spindle Shaft (REF 42) and bore of Chuck (REF 46) are clean and free of grease Press Chuck up onto Spindle Shaft_ NOTE: To avoid damage to Chuck, rotate Chuck barrel until jaws are fully open. 8 Using a mallet or a block of wood and hammer, firmly tap Chuck upward into position onto Spindle Shaft f nNSTALUNG RADUAL DRULL PRE[...]

CONTROLS AND ADJUSTMENTS _ WARNING: MAKE SURE SWITCH IS IN OFF POSmON AND POWER CORD IS UNPLUGGED BEFORE PERFORMING CHECKS= ADJUSTMENTS I OR SETUP PROCEDURES, On-Off Switch 2. Table Rotation - To rotate table, first loosen Lock Handle. The table can be rotated from side to side or completely out from under Spindle Shaft to allow work surface on bas[...]

I Cast Tab Spring Assembly /_ ))_ Feed Shaf< _ ) Lock'Nuts 3 Check operation of Return Spring for proper tension and full return 4 Nuts must be tightened before use Be very careful; the nuts hold Spring Assembly in position and should NOT be tightened flush against Spring Assembly A small gap is necessary for proper operation of Spindle Hou[...]

Belt Tension Butterfly Set Screw Angle Gauge (REF 85) on Column head and full length scored V groove on Horizontal Tube (REF 81) to set desired angle Lock in position using Lock Handle When returning to vertical position, turn Vertical Lock plunger and allow it to snap down onto Horizontal Tube When vertical position is reached, plunger will pop in[...]

Adjusting Spindle Perpendicular to Table The Radial Drill Press was factory-adjusted and set with Spindle Housing perpendicular to table No further adjust- ment should be necessary However. normal shipping and handling may have changed the setting Check and adjust as follows: 1 DISCONNECT FROM POWER SOURCE! Never make any adjustments while the tool[...]

OPERATaON Correct Drilling Speeds See "Changing Speeds" section under "Controls and Adjustments" and Speed Chart inside Pulley Cover for cor- rect drilling speeds Always disconnect tool from power source before making any adjustments Care must be taken when setting speed for any cutting tool or accessory not list- ed on chart Re[...]

ACCESSORUES Mortising Kit Vises and Clamps Although not designed specifically for mortising, the variety of possible drill angles and feed lengths with the Radial Drill Press make possible some formerly impossible operations Use Sears Model 9 BT 25255 Mortising Chisel Housing and Model 9 BT 29506 Drill Press Mortising Kit with the accompa- nying ma[...]

CRAFTSMAN 344NCH RADIAL DRILL PRESS MODEL No. 149.213340 REPAnR PARTS 72 71 7 14 ---i 87 14/__ 6 12 17 5 J 4 I I 88 15 3 53 30 29 89 : 34 54 14[...]

CRAFTSMAN 34-iNCH RADIAL DRULL PRESS MODEL No. 149.213340 PARTS LIST REF NO, 1 2 3 4 8 6 7 8 9 10 11 12 !3 14 15 18 17 18 !9 2O 21 22 23 24 25 281 27 28 29 30 31 32 33 34 35 36 37 3R 39 4O 41 42 43 44 45 46 46A 47 48 49 5O PART NO. 4910-001-951 4910-001-70 4910-252-70 4910-162-70 1737-200-00 4910-013-70 4910-014-70 4910-015-70 4910-016-70 4910-053-[...]

TROUBLESHOOTING CHART TROUBLE PROBABLE CAUSE REMEDY Noisy operation 1 Incorrect V-belt tension 1_ Adjust tension 2 Dry spindle shaft 2. Lubricate spindle shaft See "Maintenance" section 3 Loose Spindle shaft or 3 Tighten Lock Nut (left hand thread) or pulley Motor Pulley set screw, Bit burns or smokes 1 Incorrect spindle speed. 1, Change [...]